advertisement
Problem solving guide
Unsatisfactory washing result
Problem
The dishes are not clean.
Smearing appears on glassware and cutlery, there is a bluish sheen on the surface of glassware; film can be wiped off.
Possible cause
The dishes were not loaded correctly.
The programme was not powerful enough.
There is some stubborn soiling although most of the crockery is only lightly soiled
(e.g. with tea stains).
Not enough detergent was dispensed.
Items are blocking the path of the spray arms.
The filter combination in the base of the wash cabinet is not clean or is not correctly fitted. This may cause the spray arm jets to get blocked.
The non-return valve is open and blocked. Dirty water has flowed back into the wash cabinet.
The rinse aid dosage is set too high.
Remedy
See notes in "Loading the dishwasher"
Select a more intensive programme. See
"Programme chart".
Use the "Adjust Sensor wash" function (see
"Additional functions").
Use more detergent, or change your detergent.
Rearrange the items so that the spray arms can rotate freely.
Clean and/or fit the filter combination correctly. Clean the spray arm jets. See
"Cleaning and care".
Clean the drain pump and the non-return valve. See
"Maintenance - Cleaning the drain pump and non-return valve".
Reduce the dosage. See
"Before using for the first time - Rinse aid".
50
Problem solving guide
Problem
Dishes, cutlery and glasses are not dry or are flecked.
Possible cause
The amount of rinse aid may be insufficient, or the rinse aid reservoir empty.
White residue is visible on cutlery and crockery, clouding occurs on glassware; film can be wiped off.
Crockery was taken out of the cabinet too soon.
Combination tabs have been used which have impaired drying performance.
The "Combi tab" function has been selected, but the wrong type of detergent was used.
Not enough rinse aid was used.
There is no salt in the salt reservoir.
The salt reservoir cap has not been screwed on correctly.
An unsuitable combination detergent has been used.
The water softener is programmed to a setting which is too low.
Remedy
Replenish the reservoir, increase the dosage or change the brand of rinse aid.
See "Before using for the first time".
Leave it in for longer. See
"Operation".
Set the Combi tab function to
"Normal", and fill the rinse aid reservoir with rinse aid. See
"Additional functions".
Set the Combi tab function to the detergent product being used (see "Additional functions").
Increase the dosage. See
"Before using for the first time
- Rinse aid".
Fill the salt reservoir. See
"Before using for the first time
- Filling the salt reservoir".
Replace it, making sure that it screws back on correctly.
Change your detergent. Use a standard liquid, tablet or powder detergent.
Select a higher water softener setting. See "Before using for the first time".
51
Problem solving guide
Problem
Glassware has a brown or blue tinge, and film cannot be wiped off.
Glassware is dull and discoloured; film cannot be wiped off.
Tea or lipstick stains have not been completely removed.
Plastic items are discoloured.
There are rust stains on cutlery.
Possible cause
This may be caused by the detergent.
Remedy
Change your detergent.
The glassware is not dishwasher-proof. The surfaces are affected.
The wash temperature of the selected programme was too low.
The bleaching effect of the detergent used is too low.
Natural dyes e.g. from carrots, tomatoes or ketchup may be the cause.
The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes.
The affected items are not corrosion resistant.
There is no remedy.
Purchase glassware which is dishwasher-proof.
Select a programme with a higher wash temperature.
Change your detergent.
Use more detergent. See
"Operation".
Discolouration is irreversible.
A programme was not run after dishwasher salt was added. Traces of salt have got into the wash cycle.
There is no remedy.
Purchase cutlery which is dishwasher-proof.
Always run the "Quick wash" programme, without any crockery in the dishwasher and without selecting the "Turbo" function, after adding dishwasher salt.
The salt reservoir cap has not been screwed on correctly.
Replace it, making sure that it screws back on correctly.
52
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Guide to the appliance
- 5 Appliance overview
- 6 Control panel
- 7 Warning and Safety instructions
- 12 Caring for the environment
- 12 Disposal of the packing material
- 12 Disposal of your old appliance
- 13 Energy saving washing
- 14 Before using for the first time
- 14 To open the door
- 14 To close the door
- 14 Safety lock
- 15 Water softener
- 16 To programme the water hardness level
- 17 To call up the water hardness level in the display
- 18 Before using the appliance for the first time you require
- 18 Filling the salt reservoir
- 19 Salt indicator
- 20 Rinse aid
- 20 Adding rinse aid
- 21 Rinse aid indicator
- 22 Setting the rinse aid dosage
- 23 Loading the dishwasher
- 24 Items not suitable for dishwashers
- 25 Upper basket
- 25 Hinged cup rack
- 26 Adjusting the upper basket
- 27 Lower basket
- 27 Hinged spikes
- 29 Bottle holder (depending on model)
- 30 Cutlery
- 30 Cutlery tray (depending on model)
- 31 Operation
- 31 Detergent
- 32 Adding detergent
- 33 Switching on
- 33 Selecting a programme
- 33 Starting a programme
- 34 Time display
- 34 Programme sequence indicators
- 34 At the end of a programme
- 34 Switching off
- 35 Unloading the dishwasher
- 35 Interrupting a programme
- 35 Changing a programme
- 36 Additional functions
- 36 Extra options
- 36 Turbo
- 36 Combi tabs
- 37 Delay start
- 39 Factory default setting
- 40 Adjust Sensor wash
- 41 Cleaning and care
- 41 Cleaning the wash cabinet
- 41 Cleaning the door and the door seal
- 41 Cleaning the door front
- 42 Cleaning the filters in the wash cabinet
- 44 Cleaning the spray arms
- 45 Problem solving guide
- 45 Technical problems
- 47 The dishwasher does not fill/drain
- 48 General problems
- 49 Noises
- 50 Unsatisfactory washing result
- 53 Maintenance
- 53 Cleaning the water inlet filter
- 54 Cleaning the drain pump and non-return valve
- 55 After sales service
- 55 Repairs
- 55 Future updates
- 55 For testing institutes
- 56 Programme chart
- 60 Optional accessories
- 61 Electrical connection
- 62 Plumbing
- 62 The Miele waterproof anti-leak system
- 62 Connection to the water supply
- 63 Drainage
- 64 Technical data