advertisement
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
T
T
T
Printer, mouse, and other external devices
Battery pack
Hard disk drive
DIMM
T
T
CD-ROM/Diskette drive Module
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
T
System board
LCD assembly
Chapter 4 82
advertisement
Related manuals
advertisement
Table of contents
- 1 Aspire 1410/1680 Series
- 2 Revision History
- 3 Copyright
- 4 Conventions
- 5 Preface
- 7 Product Comparision
- 9 Table of Contents
- 11 Ch.1 System Introduction
- 11 Features
- 13 System Block Diagram
- 14 Board Layout
- 14 Top View
- 15 Bottom View
- 17 An Aspire Tour
- 17 Front View
- 18 Closed Front View
- 19 Left View
- 20 Right View
- 21 Rear Panel
- 22 Bottom Panel
- 23 Indicators
- 25 Using the Keyboard
- 25 Lock Keys
- 26 Embedded Numeric Keypad
- 27 Windows Keys
- 28 Hot Keys
- 30 Special Key
- 31 Launch Keys
- 33 Touchpad
- 33 Touchpad Basics
- 35 Hardware Specifications and Configurations
- 46 Ch.2 System Utilities
- 46 BIOS Setup Utility
- 47 Navigating the BIOS Utility
- 48 Information
- 49 Main
- 51 Advanced
- 53 Security
- 57 Boot
- 58 Exit
- 59 BIOS Flash Utility
- 60 Ch.3 Machine Disassembly and Replacement
- 61 General Information
- 61 Before You Begin
- 63 Disassembly Procedure Flowchart
- 65 Removing the Battery Pack
- 66 Removing the HDD Module/the Memory and the Wireless LAN Card/ the Thermal Module and the CPU/ODD ...
- 66 Removing the HDD Module
- 66 Removing the Memory and the Wireless LAN Card
- 66 Removing the Thermal Module and CPU
- 68 Removing the ODD Module
- 68 Removing the LCD Module
- 70 Disassembling the Main Unit
- 70 Separate the Main Unit Into the Upper and the Lower Case Assembly
- 70 Disassembling the Upper Case Assembly
- 71 Disassembling the Lower Case Assembly
- 74 Disassembling the LCD Module
- 76 Disassembling the External Modules
- 76 Disassembling the Optical Drive Module
- 78 Ch.4 Troubleshooting
- 79 System Check Procedures
- 79 External Diskette Drive Check
- 79 External CD-ROM Drive Check
- 79 Keyboard or Auxiliary Input Device Check
- 80 Memory check
- 80 Power System Check
- 82 Touchpad Check
- 83 Power-On Self-Test (POST) Error Message
- 84 Index of Error Messages
- 87 POST Code
- 88 Index of Symptom-to-FRU Error Message
- 91 Intermittent Problems
- 92 Undetermined Problems
- 93 Use NAPP CD to Build Master Hard Disc Drive
- 93 CD to Disk Recovery
- 96 Disk to Disk Recovery
- 100 Ch.5 Jumper and Connector Locations
- 100 Top View
- 102 Bottom View
- 104 Ch.6 FRU (Field Replaceable Unit) List
- 105 Exploded Diagram
- 118 App.A Model Definition and Configuration
- 118 Model Name Definition
- 120 App.B Test Compatible Components
- 121 Microsoft Windows XP Environment Test
- 126 App.C Online Support Information
- 128 Index