advertisement
Genesys 420HD IP Phone User's Manual 4. Customizing Your Phone
4.12.2.2 Configuring Softkeys
This section describes how to configure softkeys.
To configure softkeys:
1. Do one of the following:
Configuring via Menu: a. Access the Soft Keys screen ( MENU key > Keys Configuration > Soft Keys ): b. Select Directory ; the following screen is displayed:
The screen above indicates that softkey #1 is configured as Directory, i.e.,
Configuring via Softkey a. Long press any softkey.
Notes:
The softkey button that is configured as a PSK and the 'More' button, when long pressed, do not open the softkey configuration mode.
You can configure softkeys via the phone UI only in the Idle state.
2. Press the right or left rim of the navigation control button to navigate to the desired softkey:
Or use the navigation control buttons to move to Navigate down to an Empty key and select it:
3. Press the navigation control’s left or right rim to navigate to and select Key Event :
4. In the ‘Key Label’ field, define an identifier that you’ll easily identify in the LCD, e.g., 'Dialed':
Genesys 420HD IP Phone User's ManualVersion 2.2.8 35
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Introducing the 420HD IP Phone
- 9 About Genesys' Series of High Definition IP Phones
- 9 Complete Range of Phones
- 9 Cutting Edge Voice Quality & HD VoIP
- 11 Setting up the Phone
- 11 Unpacking
- 11 Device Description
- 11 Front View
- 13 Rear View
- 14 Cabling
- 15 Mounting the Phone
- 15 Mounting the Phone on a Desk
- 15 Routing the Handset Cable
- 16 Mounting the Phone on a Wall
- 17 Getting Started
- 17 LCD in Idle State
- 17 LCD in Ongoing Call State
- 18 Default Softkeys
- 19 Accessing Menus
- 20 Entering Numbers, Alphabetical Letters and Symbols
- 22 Displayed Messages
- 23 Customizing Your Phone
- 23 Selecting Language
- 23 Selecting Ring Tone
- 24 Enabling Call Waiting
- 24 Setting Date and Time
- 25 Changing LCD Contrast Level
- 25 Setting the LCD Backlight Timeout
- 25 Changing the Default Answer Device
- 26 Restarting the Phone
- 26 Adjusting Volume
- 26 Adjusting Ring Volume
- 26 Adjusting Tones Volume
- 27 Adjusting Handset Volume
- 27 Adjusting Speaker Volume
- 27 Adjusting Headset Volume
- 28 Defining Call Forwarding
- 29 Managing Your Personal Directory
- 29 Accessing the Directory
- 29 Adding Contacts to the Personal Directory
- 30 Editing a Contact
- 31 Deleting a Contact
- 31 Searching for a Contact
- 32 Configuring Keys
- 32 Configuring Function Keys [as Speed Dials]
- 33 Editing a Function Key Configured as a Speed Dial
- 33 Deleting a Function Key Configured as a Speed Dial
- 33 Softkeys
- 34 Programmable SoftKeys (PSKs)
- 35 Configuring Softkeys
- 36 Deleting a Configured Softkey
- 36 Configuring a Softkey as a Speed Dial
- 37 Configuring a Softkey as a Speed Dial + BLF
- 37 Configuring a Navigation Key Position Function
- 38 Removing a Configured Function
- 39 Performing Basic Operations
- 39 Using Audio Devices
- 39 Making Calls
- 40 Dialing
- 40 Redialing
- 41 Dialing a Missed Call
- 41 Answering Calls
- 42 Rejecting Incoming Calls
- 42 Silencing Incoming Calls
- 42 Ending an Established Call
- 42 Viewing Missed, Received and Dialed Calls
- 45 Performing Advanced Operations
- 45 Answering Waiting Calls
- 45 Placing Calls On Hold
- 45 Calling a Contact Listed in the Directory
- 46 Enabling Auto Redial
- 47 Pressing a Speed Dial Key to Make a Call
- 47 Transferring Calls
- 47 Performing an Attended Transfer
- 49 Performing a Semi-Attended Transfer
- 50 Performing a Blind Transfer
- 51 Way Conference Calls
- 51 Leaving a 3-Way Conference You Set up without Disconnecting the Others
- 51 Muting Calls
- 52 Activating Do Not Disturb
- 52 Retrieving Voice Mail Messages
- 53 Using Two Lines
- 53 Choosing an Extension Line
- 53 Making a Call on an Extension Line
- 54 Making Two Calls on a Line
- 54 Making Multiple Line Calls
- 54 Toggling Between Multiple-Line Calls
- 55 Toggling Between Calls on the Same Line
- 55 Answering Calls
- 55 Ending Calls
- 56 Logging into a Remote HTTP/S Server
- 57 Troubleshooting
- 59 Specific Third-Party Features
- 59 BroadSoft
- 59 Monitored Lines Based on BroadSoft's BroadWorks BLF Service
- 60 Softkey Display and Command Menu Options
- 60 Presence Management
- 61 Setting Unavailability Status
- 62 Setting Availability Status
- 62 Logging Out
- 62 Viewing Missed Calls
- 63 Configuring Do Not Disturb (DnD)
- 63 Configuring Automatic Forwarding
- 63 Configuring the 'Forward No Reply' Timeout as Number of Rings
- 64 Automatically Receiving an External Line
- 64 Listening in Capability for Call Center Supervisors
- 65 Recording an Agent's Welcome Greeting
- 66 Genesys' Contact Centers
- 66 Softkey Display and Command Menu Options
- 67 Using the Newer BroadSoft-Style ACD
- 68 Presence Management
- 68 Logging In
- 69 Setting Unavailability Status
- 69 Settings Availability Status
- 69 Logging Out
- 70 Configuring Do Not Disturb (DnD)
- 70 Configuring Automatic Forwarding
- 70 Listening in Capability for Call Center Supervisors
- 71 Recording an Agent's Welcome Greeting