SIP setting. Alphatech IP Bold series, IP Bold - tx, IP Bold - tkxc, IP Bold - txc

3.3.2 SIP setting

The door entry IP BOLD might operates in 2 basic SIP modes . It is either SIP server – door entry registration is performed to SIP server and then you call to phone numbers assigned by SIP server or Peer to Peer (P2P) – door entry call exact IP adress and SIP s erver services can´t be used.

Mode SIP server

After performing of required changes please don’t forget click on „Save“.

Display name - name by which is device presented in network (for example will display as door entry name in programms UDV panel, UDVguard)

SIP User Agent – for easy inastallation is possible use the SIP user agent. The syntax of this string is not defined, but a common practise is

„device name + version“.

38 IP BOLD - installation and operating instructions

Account - unit name in SIP protocol (usually line number or name without diacritics)

Auth.ID - name for SIP server registration

Password - password for SIP server registration

Send register – when registration is necessary (mostly yes) then this parametr must be used

Registration server - IP adress or server name of registration server (in most systems and installations is enough to insert IP adress).

Registration is performed on this server. When you dont mark send registration then dont fill Registration server and IP adres sof

SIP server write to Proxy server .

Port - SIP port is usually 5060 or 5061

Expiration[sec] – expiration of SIP server registration (period of registration request repeated sending)

Registrate after restart – when you mark then allways during restart will be unregistrated

SIP server - IP adress or server name. Over this server connection is made.

When is not filled then connection makes on Registration server

(but you must mark Send registration )

Port - SIP port is usually 5060 or 5061

Outbound proxy - IP adress or proxy name where is determine where will be

Port - sends door entry requests. If outbound proxy is setup will be

INVITE regest sends to outbound proxy adress. Outbound proxy is used due NAT. When is not used dont fill up.

SIP port is usually 5060 or 5061

SIP Transport - TCP or UDP, or automatic selection (TCP + UDP)

Provisional code – determine if during ringing will be sends SIP code „180

Ringing “ or „183 Session progress“

Enable symetric RTP - by mark is ON. It means that door entry will not sends by itself audio to RTP called party, but wait for called party to send

RTP. After sends data to same adress:port from which message arrived. It is trick used for bridging NAT

Registration status display on page as visible on picture.

IP BOLD - installation and operating instructions 39

Peer to Peer mode (P2P)

After performing of changes ple ase don’t forget click on „Save“.

Display name – name by which is device presented in network (for example will display as door entry name in programms UDV panel,

UDVguard)

SIP User Agent – for easy inastallation is possible use the SIP user agent. The syntax of this string is not defined, but a common practise is

„device name + version“.

Account - unit name in SIP protocol (usually line number), it is recommended to keep filled.

Outbound proxy - IP adress or proxy name where is determine where will be sends door entry requests. If outbound proxy is setup will be

INVITE regest sends to outbound proxy adress. Outbound proxy

Port - is used due NAT. When is not used dont fill up.

SIP port is usually 5060 or 5061

40 IP BOLD - installation and operating instructions

SIP Transport - TCP or UDP, or automatic selection (TCP + UDP)

Provisional code - determine if during ringing will be sends SIP code „180

Ringing “ or „183 Session progress“

Enable symetric RTP - by mark is ON. It means that door entry will not sends by itself audio to RTP called party, but wait for called party to send

RTP. After sends data to same adress:port from which message arrived. It is trick used for bridging NAT.

In active mode - P2P is possible to operate device, which require for their function registration at the SIP server. This option will use new SIP phones, which generally do not support P2P mode, as well as applications for iOS - Apple.

The principle of setting SIP phones and UDV guard, UDV Panel with IP BOLD:

1. Mode of phone is SIP server registration is IP address IP BOLD

(registration or SIP server = IP address IP BOLD)

2. Name and password is the line number (we choose a numbering plan so that each number occurred in the network only once, then for each device, fill in name and password to register with this number).

Example:



IP address of IP BOLD is 192.68.1.250 and the name (page SIP parameters) is 250



The IP address of SIP phone 1 is 192.168.1.200, fill in the registration here - SIP server = 192.168.1.250 and name = password = 230



The IP address of SIP phone 2 is 192.168.1.201, fill in the registration here - SIP server = 192.168.1.250 and name = password = 231

Call to SIP Phone 1 is 230 , calls to SIP phone 2 is 231 and calls to

IP BOLD is 250

IP BOLD - installation and operating instructions 41