- No category
advertisement
IDT79RC4640™
Pin
Name
ColdReset*
Type
Input
Reset*
ModeClock
ModeIn
Int*(5:0)
NMI*
Input
Output
Input
Input
Input
Description
Cold reset
This signal must be asserted for a power on reset or a cold reset. ColdReset must be de-asserted synchronously with MasterClock.
Reset
This signal must be asserted for any reset sequence. It may be asserted synchronously or asynchronously for a cold reset, or synchronously to initiate a warm reset. Reset must be de-asserted synchronously with MasterClock.
Boot mode clock
Serial boot-mode data clock output at the system clock frequency divided by 256.
Boot mode data in
Serial boot-mode data input.
Interrupt
Six general processor interrupts, bit-wise OR’ d with bits 5:0 of the interrupt register.
Non-maskable interrupt
Non-maskable interrupt, OR’d with bit 6 of the interrupt register.
Absolute Maximum Ratings
Note: Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Symbol Rating
R4640
5.0V±5%
RV4640
3.3V±5%
Commercial Commercial
V
TERM
T
C
T
BIAS
Terminal Voltage with respect to GND
Operating Temperature(case)
Case Temperature Under Bias
–0.5
1 to +7.0
0 to +85
–55 to +125
to +4.6
0 to +85
–55 to +125
T
STG
Storage Temperature –55 to +125 –55 to +125
I
IN
DC Input Current 20
2
I
OUT
DC Output Current 50
3
1.
NVIN minimum = –2.0V for pulse width less than 15ns. VIN should not exceed VCC +0.5 Volts.
2.
When VIN < 0V or VIN > VCC
3.
Not more than one output should be shorted at a time. Duration of the short should not exceed 30 seconds.
RV4640
3.3V±5%
Industrial
to +4.6
-40 to +85
–55 to +125
–55 to +125
Unit
V
°C
°C
°C mA mA
Recommended Operation Temperature and Supply Voltage
Grade
Commercial
Industrial
Temperature
0
°C to +85°C (Case)
-40
°C + 85°C (Case)
0V
0V
GND
R4640
V
CC
5.0V
±5%
N/A
RV4640
V
CC
3.3V
±5%
3.3V
±5%
12 of 23 December 5, 2008
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Block Diagram
- 1 Features
- 2 Description
- 2 Hardware Overview
- 2 Pipeline
- 2 Integer Execution Engine
- 2 Register File
- 2 Arithmetic Logic Unit
- 2 Integer Multiply/Divide
- 3 Floating-Point Coprocessor
- 3 Floating-Point Units
- 3 Floating-Point General Register File
- 4 System Control Coprocessor (CP0)
- 4 System Control Coprocessor Registers
- 4 Operation Modes
- 4 Virtual-to-Physical Address Mapping
- 5 Debug Support
- 5 Interrupt Vector
- 5 Cache Memory
- 5 Instruction Cache
- 5 Data Cache
- 6 Write Buffer
- 6 System Interface
- 6 System Address/Data Bus
- 6 System Command Bus
- 6 Handshake Signals
- 7 Boot-Time Options
- 7 Non-overlapping System Interface
- 7 Boot-Time Modes
- 7 Power Management
- 7 Standby Mode Operation
- 7 Entering Standby Mode
- 8 Thermal Considerations
- 9 Data Sheet Revision History
- 9 Changes to version dated December 1995:
- 9 Changes to version dated March 1997:
- 9 Changes to version dated May 1997:
- 9 Changes to version dated March 1998:
- 9 Changes to version dated April 1998:
- 9 Changes to version dated July 1999:
- 9 Changes to version dated March 2000
- 9 Changes to version dated July 2000
- 9 Changes to version dated April 2001
- 9 Changes to version dated June 2006
- 9 Changes to version dated December 2008
- 11 Pin Description
- 12 Absolute Maximum Ratings
- 12 Recommended Operation Temperature and Supply Voltage
- 13 DC Electrical Characteristics — Commercial Temperature Range—R4640
- 13 Power Consumption—R4640
- 14 AC Electrical Characteristics — Commercial Temperature Range—R4640
- 14 Clock Parameters—R4640
- 14 System Interface Parameters—R4640
- 15 Boot-time Interface Parameters—R4640
- 15 Capacitive Load Deration—R4650
- 15 DC Electrical Characteristics — Commercial / Industrial Temperature Range—RV4640
- 16 Power Consumption—RV4640
- 17 AC Electrical Characteristics — Commercial/Industrial Temperature Range—RV4640
- 17 Clock Parameters—RV4640
- 17 System Interface Parameters—RV4640
- 18 Boot Time Interface Parameters—RV4640
- 18 Capacitive Load Deration—RV4640
- 19 Timing Characteristics—RV4640
- 20 Mode Configuration Interface Reset Sequence
- 21 Physical Specifications - 128-Pin PQFP
- 22 RC4640 Package Pin-Out
- 23 Ordering Information
- 23 Valid Combinations