- No category
advertisement
Parameters Description
tension setpoint, which is setpoint shown in the parameter P1012. It has the read or write function as configuration adjusted in parameter P1029.
P1029 – Web Tension Setpoint Source Selection
Adjustable
Range:
1 = Setpoint via Analog Input AI1
2 = Setpoint via Analog Input AI2
3 = Setpoint via Analog Input AI3
4 = Setpoint via Analog Input AI4
5 = Setpoint via HMI
6 = Setpoint via Electronic Potentiometer
7 = Setpoint via Communication Networks
Proprieties:
Factory Setting: P1023 = 0: 5
P1023 = 1: 5
P1023 = 2: 5
Access groups via HMI:
01 PARAMETER GROUPS
∟ 50 SoftPLC
.....
Description:
This parameter defines the source of web tension setpoint.
Table 5.6 – Description of the web tension setpoint source
P1029 Description
3
4
1
2
5
6
It defines that the setpoint source will be the value read via analog input AI1 and visualized in parameter P1011.
It defines that the setpoint source will be the value read via analog input AI2 and visualized in parameter P1011.
It defines that the setpoint source will be the value read via analog input AI3 and visualized in parameter P1011.
It defines that the setpoint source will be the value read via analog input AI4 and visualized in parameter P1011.
It defines that the setpoint source will be the value write in parameter P1011 via HMI.
It defines that the setpoint source will be via electronic potentiometer and visualized in parameter P1011.
7 It defines that the setpoint source will be the value write in parameter P1011 via communication networks.
5.15 LINE SPEED
This parameter group allows the user to configure the line speed.
P1015 – Line Speed
Factory Setting: -
Range:
Proprieties:
RW
Access groups via HMI:
01 PARAMETER GROUPS
∟ 50 SoftPLC
.....
Description:
This parameter shows the value of line speed used to control the center winder or unwinder when in torque limit mode or speed mode. It has the read or write function as configuration adjusted in parameter P1030.
Load Cell Center Winder | 53
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 ABOUT THE MANUAL
- 6 ABBREVIATIONS AND DEFINITIONS
- 6 NUMERICAL REPRESENTATION
- 7 1. INTRODUCTION TO CENTER WINDERS
- 7 1.1 WINDING
- 7 1.2 CENTER WINDER CONCEPT
- 8 1.3 TERMS USED IN CENTER WINDERS
- 11 1.4 GENERAL CHARACTERISTICS OF THE CENTER WINDER APPLICATIVE
- 12 2 LOAD CELL CENTER WINDER
- 12 2.1 TORQUE LIMIT MODE
- 15 2.2 TORQUE MODE
- 18 2.3 SPEED MODE
- 21 3 WLP APPLICATIVE CONFIGURATION
- 33 4 WLP APPLICATIVE DOWNLOAD
- 34 5 PARAMETERS DESCRIPTION
- 34 5.1 CENTER WINDER CHARACTERISTICS
- 34 5.2 ORIGIN OF THE COMMANDS
- 35 5.3 RAMPS
- 35 5.4 SPEED LIMITS
- 36 5.5 DYNAMIC BRAKING
- 36 5.6 WINDER CONTROL CONFIGURATION
- 37 5.7 PID CONTROLLER
- 39 5.8 MOTOR TORQUE CURRENT REFERENCE
- 40 5.9 CONTROL WORD
- 41 5.10 DIGITAL INPUTS
- 45 5.11 DIGITAL OUTPUTS
- 46 5.12 ANALOG INPUTS
- 52 5.13 WEB TENSION VIA LOAD CELL
- 52 5.14 WEB TENSION SETPOINT
- 53 5.15 LINE SPEED
- 54 5.16 ROLL DIAMETER
- 58 5.17 TAPER FUNCTION
- 58 5.18 STALL MODE
- 59 5.19 WEB PRESENCE DETECTION IN WINDER
- 60 5.20 READING PARAMETERS
- 62 6 FAULT AND ALARM MESSAGES
- 63 7 MONITORING DIALOGS
- 67 8 TREND VARIABLES DIALOGS
- 69 9 PARAMETER VALUE DIALOGS
- 70 10 GENERAL NOTES