Konami TOP GUNNER Arcade Game Instruction Manual

Supplied By Shane R. Monroe ([email protected])
KONAMI:
INSTRUCTION MANUAL
al KONAMI ® is a trademark of Konami Industry Co. , Ltd.
TABLE OF CONTENTS
Page
Conversion Kit Contents Inside Cover “56 Pin Wiring Harness Color Code .
Introduction TE penes не. eee 1 36 Pin Wiring Harness Color Code .
Graphics. Ce eee Cee, | В .. .— ..2 Wiring Diagram ena. ee
Monitor Specifications ..................3 Dip Switch Setting... ena .
Monitor Information E 4 User Information Warning. .......
Stereo/Mono Sound Installation xh ena 5
CONVERSION KIT CONTENTS:
e MAIN PRINTED CIRCUIT BOARD
P.C.B. CAGE (FCC REQUIRED) |
+ CONNECTING WIRING HARNESS |
* 6 SETS — BUTTON ASSEMBLIES
* TWO 8-WAY JOYSTICKS
MARQUEE (HEADER)
(1/8” acrylic sheet)
* ONE SET SIDE PANEL GRAPHICS (left & right
® CONTROL PANEL OVERLAY
* CONTROL PAN EL DECALS
instruction вонь ЛА decals (2 sets)
MANUAL
o - REGISTRATION CARD
REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.
THIS KIT USABLE IN AN UPRIGHT WITH A VERTICAL MONITOR.
*THIS KIT NOT INTENDED FOR COCKTAIL MODEL CABINETS.
TOP GUNNER: INTRODUC
q . "Lat a .— , 0, = , "
.. = .. LE .. ."
. и = =
1 " =.
о".
= “
.
= . A
.
" Su - = "
" . .. h .
.
.
" 3" : . =
=" - ="
". = " .
KONAMI CONVERSION KITS are the most ‘complete
conversion kits available today. Eve r detail has been
carefully considered, designed and packaged tor provide
you the r means of easily producing a professional con-
version.
These kits have all the accessories to easily convert
your UPRIG HT video game.
and maximize your profits.
The Japanese Amusement
TOP GUNNER can be installed in any vertically
‘mounted 1 rastar scan | monitor ‘game. ВЕ
Eve ything y you will need. to construct your : new game IS
provided in this kit. All accessory parts — wiring
‘harness, joystick, etc. are custom made for TOP GUN-
NER by top engineers experienced in the coin-op in-
dustry. An 8-way Joystick with rotary s switch (as provid.
: ed) MUST be used. o
We strongly urge you to FULLY STUDY this. instruction. Во
manual BEFORE you begin your conversion. It contains 5
step-by-step instructions, schematic diagrams and sug-
gestions on how to install your Konami Conversion Kit
The Player Instruction and Button Control decals are
made of a non-destructible acrylic material specifically
— to keep. the player from peeling them off. Should you
“convert. a cocktail table game, TOP GUNNER is sup
plied with 2 sets of button decals. ——— LS
APORTANT NOTICE * * x
Machine Manufacturers Association (JAMMA) has in-
troduced a new standard in video game PC. В. S. It was decided that all new products
from any JAM MA member will use the : same f pin print-out on the edge c con nector. The
edge connector will have 56 pin e outs, 28 per side.
Konami Inc. will offer a 56 to 36 r pin adaptor PC.B. available through your distributor.
This new adaptor PC. B. will enable the new 56 |
dard 36 pin out.
pin out to adapt to Konami's old stan- _
PREPARATION:
For best results, all old graphics should be removed
completely from the cabinet. “Stick-on” graphics can be
removed by using a hairdryer or hot air device. The heat
from the dryer will loosen the adhesive, allowing you to
easily peel them off — any adhesive residue can be
cleaned off with acetone and a soft dry cloth. (DO NOT
USE ACETONE ON SURFACES PAINTED WITH FLAT
PAINT.)
TOOLS YOU NEED:
1. Foaming Aerosol (such as “Windex”).
2. Soft Squeegee.
3. X-Acto Knife.
SIDE PANEL DECALS
1. Spray area of cabinet where Side Panel decals are to
be applied with foaming aerosol or a mild soap solu-
tion.
. Remove protective backing from decals.
. Position decals into place.
. With a soft squeegee, beginning from the center of
the decal, slowly and evenly press out excess foam
until you achieve a smooth finish.
5. Allow to set approximately 2 to 3 hours before handi-
ing. Maximum adherence is achieved in 48 to 72
hours.
—
MARQUEE
PUTTING YOUR BEST GAME FORWARD
6. Trim side decal to fit your cabinet.
CONTROL PANEL OVERLAY:
1. Refer to Recommended Control Panel Layout on
page 1.
Drill any new holes needed.
Plug any holes that will not be used. (A permanent
epoxy filler works well for this step.)
. Pre-position the overlay prior to removing the back-
ing.
. Slowly apply the overlay — inch by inch on the con-
trol panel, removing the backing as you apply it.
. Once it's In place, by- using an X-Acto knife, cut
around the button and joystick placements.
INSTRUCTION/BUTTON DECALS:
Apply the Player Instruction, Button and 1 Player/
2 Player decals in their respective positions. Apply
pressure liberally. Allow to set as long as possible
before putting game on location.
о a A ON
NOTE: Maximum adherence is achieved in 48 to 72
hours.
FCC WARNING LABEL: |
FCC Warning Label must be applied to the outside o
the cabinet near the line cord entry.
(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)
1/8” Acrylic Marquee shouid be cut to fit your game. DO
NOT remove protective mask until this*is done.
One way of cutting your Marquee is as follows: (Be sure
to protect painted side of Marquee from any surface
which may scratch or mar finish).
CUTTING WITH A KNIFE OR SCRIBER
Acrylic sheet up to 3/16” thick may be cut by a method
similar to that used for cutting window glass. Use a
scriber of some kind — a scribing knife suchas the one
pictured, a metal scriber, an awl, or even a sturdy craft
knife — to score the sheet. Draw the scriber several
times (7 or 8 times for a 3/16” thick piece) along a -
straight edge held firmly in. place: It is best mot tb.
remove the protective masking. Make the cuts carefully
using firm, even pressure. For best results make each
stroke cleanly off the edge of the sheet.
Then clamp the acrylic sheet or hold it rigidly under a
straight edge with the scribe mark hanging just over the
edge of a table. Protect your hands with a cloth, and ap-
ply a sharp downward pressure to the other side of the
sheet. It will break along the scratch. Scrape the edges
to smooth any sharp corners. This method is not recom-
mended for long breaks or thick material.
- LR
Always draw the scribin
knife along a straight edge.
- - wl 4 =+ и
tp PE dE
Break sheet over edge of
table after scribing.
P.C.B. CAGE INSTALLATION
Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation.
The cage is made of a 32 point stem-stock which is fire retardant.
TO INSTALL THE CAGE: a
1. Open cage bottom and secure to desired P.C.B. position.
2. Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
3. Close the cage over printed circuit board and secure with latch on cage.
2
SM —
TOP GUNNER: 36 PIN WIRING HARNESS
36 Pin Wire
Harness ||
36 to 56 Pin
Adaptor Card
WIRE COLOR KEY:
WHITE/GREEN
RED/GREEN *(Mono Speaker Output)
YELLOW/RED
BROWN/YELLOW
VIOLET/WHITE
ORANGE/WHITE
RED/WHITE
BLUE/WHITE
BLACK/WHITE
RED/GRAY
GRAY/WHITE
PINK/WHITE
GREEN/BROWN
RED/BROWN
WHITE/BLACK
BLACK
BLACK
RED
Solder Side
without major rewiring.
Parts Side
(NOT USED) + 12V DC
B| 2 | “(Mono Speaker Output)
2P GUN | C | 3 | 2PMISSILE
2P LEFT | D | 4 | 2PRIGHT
IP START | E | 5 | 2P START
1Р MISSILE | F | 6 | 2PUP
1P GUN HT (NOT USED)
COIN 1 | L | 10 | COIN 2
1P DOWN | M | 11 | COIN COUNTER 1
(NOT USED) | N | 12 | COIN COUNTER 2
VIDEO GREEN | P | 13 | VIDEO BLUE
VIDEO RED | R | 14 | VIDEO SYNC
(NOT USED) | S | 15
GROUND | T | 16 | GROUND
GROUND | U | 17 | GROUND
+5Vpc| V | 18 | +sVDC
(BASE COLOR/LINE COLOR)
*SEE PG. 5 FOR SPEAKER WIRING
Supplied in TOP GUNNER you will find a 36 to
56 pin card connector. This connector enables
the operator to convert his Konami wired video
cabinet from the old 36 pin harness to the
new JAMMA standard 56 pin connector
If this kit is to be installed in a non-Konami
«Wired cabinet a wiring harness is supplied.
ORANGE
ORANGE/GREEN
ORANGE/YELLOW
BLUE/YELLOW
VIOLET/YELLOW
BLACK/YELLOW
ORANGE/GRAY
BROWN/WHITE
GRAY/YELLOW
BLUE/GRAY
GREEN/GRAY
YELLOW/GRAY
BLUE/BROWN
WHITE/BROWN
PINK/YELLOW
BLACK
BLACK
RED
TOP GUNNER: 56 PIN WIRING HARNESS
Solder Side -— Parts Side
WIRE COLOR KEY:
BLACK
BLACK
BLACK BLACK
RED RED
RED RED
ORANGE ORANGE
WHITE/RED COIN COUNTER 2 "J | 8 | COIN COUNTER 1 WHITE/BLACK
vero [Ko] ver
WHITE/GREEN (Mono Speaker Output) Lo 10 | (Mono Speaker Output) WHITE/BLUE
(EMPTY) | M | 11 | EMPTY)
GREEN/WHITE VIDEO GREEN N | 2 VIDEO RED RED/WHITE
WHITE VIDEO SYNC | P | 13 | VIDEO BLUE BLUE/WHITE
YELLOW/BLACK SERVICESW| R | 14 | VIDEO GROUND BLACK
(EMPTY) | $ | 15 | EMPTY)
YELLOW/RED COIN2| T | 16 [CONT — YELLOWIBLUE
— WHITE(IOLED 2P START | U | 17 | 1PSTART Iyllowndidr ¿SAANGENLACK
(WHITE/BROWND 2PUP | V | 18 | 1PUP WHITR(GRAY)
(ORANGEIWHITEY 2P DOWN | W | 19 | 1P DOWN GRAY
ORANGE EDenbli) 2p LEFT xm 1P LEFT VELLONIGREEND
P SHOOT >= 1P SHOOT
GRAY REDA :
GRAY(GREEN +‘
BLACK GND | e | 27 | GND BLACK
BLACK —GND| f | 28 | GND — BLACK
(BASE COLOR/LINE COLOR)
В DIP SW No. 1 Settings
Coin 1 Switch det
| COIN | PLAY
Ш 1
N
ВР
q
“oia > w |
F
DIP SWITCH NO. 2 2 SETTINGS
“THE NUMBER OF PLAYER S LIFE o
do
O
+
C
0
23) ВЕ za}
TT 0
AL LL
| | | |0|lo/2 9
| an |
| > | Y IN
FIRST
30000
50,000
30000 | NA
150,000 —
о.
DIFFICULTY
EASY
NORMAL
DIFFICULT
_ VERY DIFFICULT _
DIP SWITCH SETTINGS
8 |
OFF
OFF
con 2 Switch Set
7
OFF
| SECOND
250,000 |
ON 7
6.
OFF
OFF
ON
5
OFF
ON
Com [Pay
ON
ON
OFF
_ OFF
OFF
ON
oN _
OFF
| oFF |
ON
ON
OFF
OFF
ON
OFF
ON
OFF
8
OFF
SOUND IN ATTRACT MODE
on
OFF
OFF
ON
OFF
OFF |
= | 5 | | = | с | 5 | = | 3 | о | | | оо |,
1
1
1
7
1
1
2
2
3
3
3
4
4
ÓN
INVALIDITY
"SW 3 NOT USED
DIP SWITCH NO. 3 SETTINGS
VIDEO SCREEN FLIP
NORMAL
UPSIDE DOWN _ —
‘+ SHOWS NORMAL SETTING
*SW 2, SW 3, & SW 4: NOT USED
HER: MONITOR INFORMATION
SERVICE INSTRUCTIONS
NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every
time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis
become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move
the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6
feet before turning off.
1.0 BLACK LEVEL CONTROL ADJUSTMENT
This control has been set at the factory and should not
— need further attention, however, when the game is con-
nected a slight adjustment of VR201 may be necessary to
obtain the proper black level (the black portion of the
9.0 HORIZONTAL WIDTH ADJUSTMENT
~The horizontal width coil is a hexagonal tuning tool ad-
justment. This control must be adjusted slowly, if
necessary, until the picture or test pattern attains the
correct horizontal proportions.
picture just extinguished).
2.0 VERTICAL SIZE (HEIGHT)
Location of this control is shown in Fig. 1. This control
must be adjusted slowly, if necessary, until the picture or
test pattern attains the correct vertical proportions.
3.0 CIRCUIT PROTECTION
A 4.0A pigtail fuse, mounted on the Main Board has been
provided to protect the Power Output Circuit.
* KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC.
USE THE THREE PIN CONNECTOR ON THE MONITOR.
GRAN — 19% — RED
DRIVE DRIVE
4.0 FOCUS ca curo
Adjust the focus control, located on the HV unit (T352),
for maximum over-all defination and fine picture detail. SLU CUTOFF
5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, Nee и SUNG NOTE:
VR351 (See Fig. 1) GND © WHEN USING COMPOS
ITE SYNC USE HORIZ,
A warm-up period of at least five minutes should be
SYNC INPUTS.
allowed before alignment is carried out. With the monitor
being driven from the game signal, short TP601 to TP31.
Adjust VR351 until the picture stops sliding horizontally.
Remove the short.
6.0 HORIZONTAL VIDEO POSITION
If the video is off center on the raster some compensa-
tion can be made by adjusting this control.
7.0 VERTICAL RASTER
POSITION ADJUSTMENT
If the video is oft center vertically, (short dimension of
picture tube) some compensation can be made by mov-
ing the vertical raster position adjustment jumper to
either positions “U” or “D”.
8.0 HORIZONTAL RASTER
POSITION ADJUSTMENT
If the video is off center horizontally (long dimension of
the picture tube) some compensation can be made by
moving the horizontal raster position adjustment jumper
to elther positions “R” or “L”.
POS H SYNC
POS Y SYNC
HORIZ HOLD
BLK LEVEL
(un
ain
HORIZ VERT VERT VERT HORIZ
CENTERING SIZE HOLD RASTER RASTER
SHIFT SHIFT
FIGURE 1
TOP GUNNER: MONITOR SPECIFICATIONS
TOP GUNNER requires a vertically mounted monitor. It also generates composite negative sync. If your monitor is
composite positive sync, you will have to change to composite negative sync.
(1) To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the
output pin from the P.C.B. is a combination of H-sync and V-sync.
NOTE: Please refer to Figure 2.
FIGURE 2:
+5V 14
FROM P.C. BOARD 1 12 7
NEGATIVE COMPOSITE SYNC. = GND OUTPUT TO MONITOR
(PIN 14 on P.C.B EDGE) POSITIVE COMPOSITE SYNC.
(+ SV and GND should be taken out of the P.C. Board.)
‚ (2) Separate Sync modification for TOP GUNNER if your monitor has “Separate Sync” input. (For example
“Electrohome brand” and “Wells-Gardner brand.)
Step 1
WIRING HARNESS
VIDEO SYNC
я [14
-HÍ-V NEGATIVE SYNC INPUT
ul |
ss! | 1 MONITOR BOARD
If the picture is still not stable...
Step 2
Prepare Hook-up wire to seperate -H and -V sync. signals.
WIRING HARNESS
=
VIDEO SYN
Rj14 -
$ [15]
SVCN4P °
5 3 | E nal | I À ru
LU | cy Ae T UA L + I г L CT >>
TI ps nop 66 Û € > py B21 a NG wo a 9! > bd
1830 G si 135 jel A O LAS-d2
mn 690 41) GV GE nal Е EV q LMS-d
2 2990 661 | [vw 319 2»5 SET (6 [57 | | 9 | °| me 1
Я —3 DA | 9V я sa: * AL LI bd
21] £820 Е Ly El 14 L 39 PA — bg £0 8MS-d2
0320 ov} | | 06 Y ey заст T de | pin ea | L500
02 05 | . и” Е TT T E
EL. Ep | | | ae ES E zm ENE 22 102 3 y de oh +4 ix aw 80 INI09
LL Sas ЕТ | | 29 "бу >) O Al Ci ST * | | с gl
£420 Ev | 775 ste 30 18) 1 + al ie ves 002157 ЭМ La
Gl 95 - 5 Ш gEN vz AH 2u 2——“a 20109
. ge | | ET 810 — ve 1" 19° se ea —jes evk “o 3911438
och gy Lb | | 877 Ta ТУ TE a 00 ven € 9 an Е IE vel LLL | foe , JEN] 261 G avi) q H
val LY | id Tae ee 10 EV 5 | 0 |
¥) Ob— | т: gbl co: 0! = | de -
71 209 nos va | [oo ET St He * ve — Df MeUITT = £42500
Bd + | =~ - | - | Id
gg] “A po + au 5 057 | Y o, BOTS ae o O = (6157 | | 91 pe wif 1771" IZ n 1%
ge] E | 7 IV 96 a 50 Lyre - © | | SNK
ME 2 8057 0 ¥/S | 18 LY oe} oe T ЗО av cz 1 let | 001 g | aad TEJA cv 5 <0 1431-d¢
9 "668 o 7 — — T6|9 na 5611 OV ве NI 7! DUT | |
Ta | - À ET is NN E |, УЧЕТ ав 2 ai Tale Eg — та 1H91#-d2
bl, LEIA ALL | 419 | | a LLY EZ | 4 al с т gin eal = { 6749 E
+H can [18 | El 3 | [e asi az fo GI
5, 040A PONE ТУ | | VE “es 092 | ELZS00
a L49A — | ai — 0 EFS DI — “BIE ae Ae LIE | en | 1 LA LY ld NADO-dé
7 = e” TT ses la 6 MIG | 2 "
> 2% e | | | ay | veus 22211 NN
AN; / | : y | |
588500 es | HH a | LS 1 ST || £6257 "TP at Eva 4 2100HS-d2
| DIN | = | : Evan
gf 008 т E a ГГ | | - es — afr ws 90 €100HS-d2
En ло ve à Ei ll 8 £42500
Lg №0 т TH 0! ol y 410 id 3
LJ 0 | > TV T | LA LY 0 14]31-dl
pq] € 08 b | 5 ac | | ¿ Е С ВТ o of | > 02
— 104 EX IN — _ |8 |S | A A DD a о (№ r
L550 Ch | | | [ DE 0$ "e Га у EY e E aT er a NE 1 1H91H-di
1119108 SIN 1 ZY3LNNOI NI09058 ‘8 > гало Ol ne 268 и a T “st | | Ld A
СЛОВ | 5 L A le af 9 ess AT | | 08 ВИЙ ий
SI IN. E log we av 95 | |] cvs
LI 13534 Lines ha TP e Ly arty | ONIFT 7. 9 NAOO-di
ONG 4 | LH31NNO9 N109058 57] HIND © Bl av agit ||| J9A un ¿E 8 61
71 0008 | yp | at PLIS Te 6)" na TT ap | T £42600 +:
01] or | | | L
59] 100$ TWNN == | «< т 095 Sres E e pa sE ani NG 550 1100HS-dI
iy o W E 13534 UV em a = ——— 92 So ME ls sn ld 2100HS-di
SL слом | | ® “вит AZL+ | — = Ga NE sup € b EC
3) sno JE, ma Fp - late | = vel ee e ev 3 ELO0HS-di
== поч сб | Bud Fr ¿ESOO 1 | $ | mS 947 9 . e
ЕН улом И 21+ G+ | O Bellic 75118 | |
| Er | |
ok | | I A “a b/ST | ZEST | II a о WId ov ov D Go
de | | 1 Lez 2A | Tze "|
a. Ti | hs ||, || 118 evis om y 01 3 8 st
9 OH NaN 901 | | | 9 3 #1) | | tl POS | | zen b L € i. 19 2\ b | b 2
—9 y il 3851 | Cs 4 | Fi 2857 || y WH "ia tg] 2A g MD 61
LEN E | 9 EIN: | od 77] 90 cure | “VIL ey)
7 by 3 Ned 09 1 Li | haria 051 vf | 82N ica? yal 3
<I al | E E III N3 | [té Г 100 SY Ese {SY |
Ol e, GS N 8 4 G| ; Z | [T5904 | ero [60 vss Via da > 110 091 NE оф 19 ws |
bi DE | ON | II dt gen "2 va 6Y | 20 LY LY
3 qu INEST | | 5 9 GO Ol be MEL ea 65 8% E! g ve
—=1 0 | < Li] 392 ces a A "reo С @ АНК GZ 949
196 at ve INAS | 9 | 695 HIE 21190 Liv ra? rc mias Sg
ol 95 | [|| ZEA 7 NETO 2 Hea ou El ou
51168 Г 2 || AL | |< 61 cie AZ, — y 12981, bXAL |
eo IHN = | ot |S | || ee CA ED TAL | [3535
€ { i даа | d = La ZIV A —— qz3z
uE | G+ 3319 и Le ol. A 0814
09 > Te о | | 523199 Г Fi jad SIV | Eliza] EN - == 632
Ole 2 | 3! | aavo 111 |! (26 ane DO) || Lao 09 31%, AE bi . mile
dd | _ Y
ile I. Te le | [гг ME 22 v1 [02 _ sues] SH &
ar 8143 | 9HIN B| ge | LI 8037 | — 31 nag В bl “I Bm _ EE
= 22^ | | | с оо су В | = Т - 23
[TTI] een vf - REA 2
+ SvL LST EST EST] | | = _ [021 wig G+ e VHS
— ES Lal 2: + - - pr VLS | IL x PbS 6 EY IG nds I al
C+ - i il" € 108 618 oT ON9 OLY + 2667 ! По
+ 258 x all OT
i E || O-ZHW2£b'81 | p G+ cv =<
Ep a — \6+ EPELOD
5
0052 7/3
я 9 —=11C3
9 rN Sag E | я 1с2 ve |
| 2P-5W7 o 6 —=11C1 1Y | | =
| | P4 A3 vb _6 00 я | 5157 io B 90 |
| 2P-Su6 OZ 4 3 — 16 кв a | |
P4 “e ona Y? 4B " 542 ze 6 - CK es ULF UT
2p-SW5 DE 2 — | ЗА > nalo E освз |
pa mm ши | + E a TL освг
2P-5W4 о? 8 ws 13)... A 2B "a 2 DB6 7
x 5-84 -— va? pe | ff 1112125 [11 32a > pre M Des que
| 2P-SW3 Op of cra7 | | E | IM con 18 | a 084
| P4 a 3 а 10 >c0 er = 1A wid a A DB3 8CD3 72
| | — 2P- 3 | | S76 EN DB2 |
| + SWZ Og; 4,0 vol: N E ы | 157 De aco? = |
| Op-SN1 ne 2 RN3 | 3 3E | = _ | DBO OCDI 75
| P4 — AI vill] 629 гг || 4 pa U12 | 11 LS157 | | | ocho
| 005273 12 19 | ;
| 1Р- 9 | 11 Y - 46 y LS139 |
О sue oie Lo O pe | ei sol ‚а.
1Р- 8 CRA2 | 16 | > 38 5 15 | Y3k | 28 COL3
| SW7 Op3 Sla3 val? F5 | | 3A : sn ap} 3p sis LE | 821 og COL2 e
| 1P-SW6 О 4 A? y la | . 3 501 = 12A 2Y AN 14 A 5 rl 511, 2 A 108 YI 5 — NR! COLT 14
| RN2 I Ш 14|LS per vob €. 4 NWRO ts
1P-SW5 СР 2 1 | e ol 12, X dl en OP
| P3 Al у! 4 т 203 | 1A i 15 . то ;
| 005273 202 то гк Г L509 NCSY ==
a ; 5 EE» 11 | 15 , 59
| 1P-5W4 D53 rm 7 | ps 10 к! oy e 124 tan NVSY E
1P- 4. СКАТ 575 — FAG
1P-Sw2 035 ú до ord 5 A 1C3 UB RO ai 23 Lys 20| 14| 22 dan NV@C H33
RN | Tee | 1 al22 Bu 271, GND OF | e des nage 19!
1P-SW1 DS 2 | rele 1Y} 3 А14 1 nvew 10
РЗ, — Al Yi 1 10 Ol ico | А13 с 13 261,13 | ? РА! |
/ RAI | Ш! EI RESET 3 A2 1 = 2/012 D7 19 18 = FAO |
116 A" 1 3 pr 23) 18 D7 SY 1133
ı|RA2.2KX8 rie boa! © 17106 axıı 90
| ash? HI 24 |^10 D5 + 16/95 SHE | FD7 AX 39
| DIPSWI E E: 25 he 513 o Е ía В 8d) “wis [167
| 1 >. [16.43 4| 51 6) 7| 81 9 ivy * Ya nl 13193 5 SO 33] 0° axe 13€
| a — 15 1] o MESAS gC D Pane % —— 55 08 1x7 199
3 LE 14 | M A5 = as 11 E p1 U13 + 8 "РОЗ 138
CM 3 о |3 CEE “ AE 1144 U37 DO vec ={FD2 ax [166
ERs En AB Lo 814 q GND ia axa
| - e 11 = re | 14 А? 3 я 3 д? ps 28 5 AD FDO AX3 88
| a ul. A e A A = 10 Al VPP yn = 1 116 AX2 37
( ~ 19 AD — a0 2. 10 29 ax [8
| | 17 + E CS cr28 = CH? [1 NTIH АХО 36
и E 2725 | НЗ ress
| | U15 ” LI 56 Eck Cr cm ry TES?
| | 1|RA2.2KX4 D7 (55 “ ==" m1“ 180 — [170 TES3 vor |164
811 ots к pr 5 E | Mao § hores vos ES
P5W3 | LS257 57 La +5V mp ESE 72791 Ce 172 vés E
1 o~ [8 13], SEL, is À | Wes a voa >
al - 4 ya: 11] ay 3 BSC Гео | ТЕЗЭ 85
0 5 | 3A 5 31 Em | К vol 34
+ + ; д 526 20 ay 1 85 MT - — on
a U7 RA: e A | 41 SOUND-R 5 | 35 - = ==
| 2.2KX8 2] 1Y 1 a a1 15 125 140
| | 1A Ш 1 2 1 1000U16E SOUND-R - 133
De 2| 3| 4 и SOUND
~ [16 4| 5| 6| 7| 81 9| | S244
| 2] : 1 SOUND -
Е J I 15 = o sou “on x +
6 "Ч 11 6 В ЗА SY BUT1 BUT? BS +12
7 ss [10 + - Bl “| SOU-R № = E +] Ct
3A |
— 8 > |9 я | Я гл 5 и hot IN U2 LA4445 is ‚1UCX34
| A SE ий —1'A 1Y S0U-COM IT e | GND_GND |
f ¿> то sou "A 28 .
go ; ЗиК | 197 SOU-COM vse Wenner Wzzonee A
i L 1 1 >
A o oi
: 7 | r - лы GND Ору L
| = a
ov —— (0820
ban vs se 1920
[HP ву 2600
| BS EY bG 11 £80
00 airs 571 0420
LO су E 1320
20 9% 2400
bt ED Ma SL 490
X18 HAD _ ana ina |“! GG |
135
A HS
Bt
LS i.
HI OL
€01S Ce
20
Let LOO ca
volé
50
| vl El
« LEZ
Ll
gl
61
0c
00
La
za
Ea
vo
ca
Cl 90
№ La
A al
LIN v2
714% Hb gz
VE
A ||
6|^° ces A
1 hi
ell e EL
LS IS ||
»
NLASVW
as: 9 — 089A
La — | 1990
ETT 28%
BC CAJA
Le 20 040A
az ÓN LADA
" Gé (21 240A
bé 60 || +394
€ WL ASTIN |
Co ov a |
ov "NIG 59; 0704
26 "ye oil
27104
Ё y GE ь La La
bE JIA y q = E ON
Ey SV PLL lou
ME 92n ayls ||
ct Ob b 67104
99
9 ve va “E E 1119108
gy De 00 BY (108
¿Si
<T ju)
CO
Onda
|108
¿nd
nay
УПЧ
sniy
nay
ECH
Ol
"E,
|||
151
6
AS
LL
0G 1!
39
0c
ov Qu
lod La
6 E.
8 L
ev Eu
9 5011
GY ty
sen gy: SV Loy
HL ¿y Ay
618 gE Eo
Ge 801
sv, A bas
OS OLE
LLY LLE
гие oe
Ely ELU
O ETA 9 |
PLA
TE: Or:
LA
sul 6b1
39 22
De
Gl 451
avi
E9S
88500
JJA
LOSN
S JAN
AWN
JOIN
Ol
6
SIXN ans 2V
cvle
L
WA bY
MXN GV
02N gy 4
SIN HB of
oo °'S gy
LO EL
bé
Lé
I NNN
DYIN
ЧТ ЭМ
E
e ol
Jan ONS 2y -
| an
OdIN 2A by
E.
3dON 0SN gylS
HL ul”
он! 00 * gy =
10 6\
¿MIN
L MIN
91M)
691 66561
eG! 191 til
980 MG 1
L Nay
ETA я
LEN ve
Ov 7 AZ HL gz
Y
- 6|* 695 %*
vt
ОН отв
461597 |
LUEY
OV
EN Y!
НО 2Y
LLS EV
LA
LO GV
T 0 qv
= 0 LY
¿NJ Ni
bi JEL
ELY
cl
LD | NE PUC E
WIMSVM
(7
Cu
С
ge
Lc
|
IN
3)
Ос
NLASVW
| |
CRES
G+
23
AM
- 590 D?
12F ni le
Us no
| 282883826888
+12 C
+12 C
e
wp
a ape AT на. a я =; F = ЧР
€
coL4 tro SYNC ‚45367 Р
= INRAS COL3 = © го > ' —^м pyOSYNC |
NCAS со. 2 pa— |
NF OE COLT
NWR 1 COLO e
NWRO |
nesY (4,
wr BS,
| | FA? |
| { CLR | FAB |
у 1 = FA5 |
Y | Tal - FA4 мос 27
{у |
| 4464 [ess ve] Faz ним 80-3 5 -NOTE-
| © 1017 RAS РА! | 271 6264SL
+ 16 OF FAO +5
26 | AX12 o 55 дуг 74 E e % VCC(+5V) |
AX11 39.211411 82 —— +12 |
19 FD7 AX10 167 54 A10 о: +12V
18 I FD6 AXx9 132 25 [Ad D7} ;
7 he: FD5 AX8 AB 06
к FD4 AX7 = —F ЗА 05 = : GND
115 FD3 AXE | D4
(13 FD2 AX5 > D3 À : NC
FD1 AX4 | = D2
a FDO AX3 a D1
AX2 | DO
| AX 3 |
INT1H AXO | * KINDS OF CAPACITOR |
Eos T : TANTAL
| TES3 v07 M : MYLAR
| TES4 vO6 E : ELECTRIC
E seg C : CERAMIC
TESB v04 |
{| TES7 Vo3 |
TESS vo? 570 JAMMA EDGE 56PIN
: - = PIN NO.
GND veo NUMBER: PARTS-SIDE
er nar aaa 41111 ALPHABET : SOLDER-SIDE
15H |[GND VCC 69 93 115 125 140 /A/ A SMALL LETTER
3 u23 18] TILT. hy 550 4P-CONNECTOR |
550 13P-CONNECTOR |
1P ROTARY SW.SOUND |
570 13P-CONNECTOR |
2P ROTARY SW.SOUND |
= 5=0 4P-CONNECTOR |
88) py eS pa 88) ps MONG
+| C6 KEL56P CNT 3P NHCN4P 550 4P-CONNECTOR
ZZ 1000U1 6E 51 р ‚6 STEREO
НЕС. ТУР
2reno t 2000 IGonami | KONAMI INDUSTRY CO. .LTD.|REC-TYPE| SCHEMATIC DIAGRAW
P2 Po a da: ыы _ |
GND GND 88) p2 88] pa 881 p7 DESIGN| DRAW | CHECK |APPROVE RELEASE NAME
P3 Ра — mia я |
¡Oc | 10 cc SVCN4P CN 3P NHCNAP So | DATE |86 , 6 27 OXO31 — puB302067A
РЗ Ра
©] 66] e . | TOLE-
oan Liao IDAKA | IDAKA SCALE |. mance | Al |” "| 101006
}
1
р
K
TOP GUNNER: STEREO/MONO SOUND INSTALLATION
Konami introduces stereo sound.
Please read instructions carefully. If your video cabinet doesn’t utilize two speakers, follow
instructions for mono output.
- Stereo Output Connector B13P
- =
= ны В o 1 d
= = 1 k E "
Tk
6X631 | HOW TO CHANGE TO
q — MONAURAL/STEREO
с
“Note: Мопо & Stereo sound cannot
operate simultaneously.
‘For Mono Sound
Use pin #10 and Pin L of the 56 pin edge
connector to the speaker contacts.
Also connect Jumper connector to
mono B4P.
Use left hand volume control to adjust
| sound level.
For Stereo Sound
Jedunr dYg OUON
1edwnf dyg 080181S N
Use pin 1 and 2 of connector B13 for
right speaker.
Use pin 3 and 4 of connector B13 for
left speaker.
Change jumper connector to stereo
B4P.
CUSTOM
ë
CUSTOM
CUSTOM
TOP GUNNER
REQUIRED POWER CAPACITY.
+12у
STERED ВЕ
ОС PARTS SIDE
-SOLDER SIDE
- я
— | FUSE 3A
ans sn | 8 N6V AH 1 SUPP! | .
ress FUSE 2A Ш
„DIN
HI] WIN COUNTER?
COIN COUNTER! EO
COIN COUNTER? Less — —
COLOR MONITER — E ==
— ce N SERVICE [5s
| COIN | [53 TA + : PE к
COINZ
1P START - + 26, START в т
: RE Tr To — ЗРК
CONTROL FOR de o —H 2 == eE ae
A Ds | LR OT CC Eo TE | | 0e A o AR LEFT
a pq AN it: Mid To
в >» 1 st 2Р LEFT.
2P DON | ПП. т re LE de
Má TH + Rig
Filer | IL —~1 LJ 2P
E Me a € Se
SAMEN “contre pA 26 Sheets
ONLY FOR TABLE TYPE
GND
L | GND
E
CONTROL FOR 1P tin —
-— Hi — JAMMA S6PIN EDGE CONNECTOR
| | Oo O O ©— Осне@ет? TT | 2/32 INCH PITCH .
— ore at IN - NOTES
и ORIGHT PIAR 1 ISPEAKER T 7 - NO - 1 1P NO.1 PLAYER
| oT + SPEAKER LEFT 2P NO.2 PLAYER
- O DON ; — 2 SURGE KILLER DIGDES FOR COIN
— COUTER INSTALLED ON THE P.C.B
|
USER INFORMATION
WARNING
F.C.C. REGULATION COMPLIANCE
THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED
VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983
WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE-
QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A
COMPUTING DEVICE.
IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO
ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED
FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER-
FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE
OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY
TO CORRECT THE INTERFERENCE.
THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION
KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT
THE TIME OF INSTALLATION.
ar KONAMI.
815 Mittel Drive, Wood Dale, Illinois 60191
Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973
For Technical Assistance Call Toll Free (800) 222-6181 (Outside Illinois)
">