Konami JAILBREAK Conversion Kit Instruction Manual

* JAILBREAK CONVERSION KIT *
(INSTRUCTION MANUAL
=
f =
nt
>
e
ve
por
ZN
©’ Копа © wes
UL
BREAK TM is a registered
trademark of Konami Inc. © 1985 Konami Inc.
- «= 1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 Konami» is a registered
So TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW trademark of Konami Industry Co., Ltd.
Konami Inc.
TABLE OF CONTENTS
Page Page
Conversion Kit Contents. ....... Inside Cover Wiring Harness ColorCode . .............. 5
Introduction. .......................... 1 Important Installation Notice ............. 6
Recommended Control Panel Layouts ...... 1 Wiring Diagram ............oeeeevecoer 7
Graphics..........eecesxeecorrererdanen 2 Technical Information ................... 8
Monitor Specifications .................. 3 Dip SwitchSetting...................... 9
Monitor Information. .................... 4 User Information Warning. ....... Back Cover
CONVERSION KIT CONTENTS:
e MAIN PRINTED CIRCUIT BOARD
* P.C.B. CAGE (FCC REQUIRED)
* CONNECTING WIRING HARNESS
* 6 SETS — BUTTON ASSEMBLIES
* 8-WAY JOYSTICK
e MARQUEE (HEADER)
(1/8” acrylic sheet)
e ONE SET SIDE PANEL GRAPHICS (left & right)
* CONTROL PANEL OVERLAY
e CONTROL PANEL DECALS
instruction decals/button decals (2 sets)
MANUAL
* REGISTRATION CARD
REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.
THIS KIT USABLE FOR COCKTAIL AND UPRIGHT VIDEO GAMES WITH A
RASTAR SCAN MONITOR WHICH IS OR CAN BE MOUNTED HORIZONTALLY.
JAILBREAK INTRODUCTION
KONAMI CONVERSION KITS are the most complete
conversion kits available today. Every detail has been
carefully considered, designed and packaged to provide
you the means of easily producing a professional con-
version.
These kits have all the accessories to easily convert
your UPRIGHT or COCKTAIL video game.
We strongly urge you to FULLY STUDY this instruction
manual BEFORE you begin your conversion. It contains
step-by-step instructions, schematic diagrams and sug-
gestions on how to install your Konami Conversion Kit
and maximize your profits.
JAILBREAK can be installed in any horizontally
mounted rastar scan monitor game.
Everything you will need to construct your new game is
provided in this kit. All accessory parts — wiring
harness, joystick, etc. are custom made for JAILBREAK
by top engineers experienced in the coin-op industry.
An 8-way joystick (as provided) MUST be used.
The Player Instruction and Button Control decals are
made of a non-destructible acrylic material specifically
to keep the player from peeling them off. Should you
convert a cocktail table game, JAILBREAK is supplied
with 2 sets of button decals.
SAVE YOURSELF TIME AND MONEY
The following P.C.B.'s are interchangeable with JAILBREAK P.C.B.'s
Super Cobra ® Scramble * Pooyan *e Locomotion * Circus Charlie * L'il Hustler
Juno First * Time Pilot * Gyruss e Tutankham e Turtles *e Super Basketball * Mega Zone
Pandora's Palace * Time Pilot '84 * Track “n' Field * Hypersports * Roadfighter e Yie-Ar Kung Fu e Kicker
Rush 'N Attack e Mikie * Frogger (60% — check pin print-out) * Amidar *e Roc 'N Rope * The End
In other words, your JAILBREAK will plug right into existing edge connectors of the games listed above — be sure to
check your pin print-out. (Keep in mind that JAILBREAK is designed as a horizontal game.)
DUAL CONTROL
By moving SW#2 of dip switch bank #3 to the “on” position, you are now in the dual control upright mode. This allows
you to set up an upright game with two sets of controls rather than one set. The first set of controls should be hooked
up to the 1P set of wires; the second set to the 2P wires (see wiring diagrams). Each player still challenges the
“computer-controlled” opponent (alternating play). This does not allow simultaneous interaction of players on the
video screen.
*SINGLE CONTROL LAYOUT
DUAL CONTROL LAYOUT
1P START > > 2P START
> >
SHOOT SELECT
& &
SELECT SHOOT
E >
1P START > > 2P START
808 OS
7 SHOOT SELECT Te SHOOT SELECT
Ta
5
29
TI
* RECOMMENDED LAYOUT
PUTTING YOUR BEST GAME FORWARD
PREPARATION:
For best results, all old graphics should be removed
completely from the cabinet. “Stick-on” graphics can be
removed by using a hairdryer or hot air device. The heat
from the dryer will loosen the adhesive, allowing you to
easily peel them off — any adhesive residue can be
cleaned off with acetone and a soft dry cloth. (DO NOT
USE ACETONE ON SURFACES PAINTED WITH FLAT
PAINT.)
TOOLS YOU NEED:
1. Foaming Aerosol (such as “Windex").
2. Soft Squeegee.
3. X-Acto Knife.
SIDE PANEL DECALS
1. Spray area of cabinet where Side Panel decals are to
be applied with foaming aerosol or a mild soap solu-
tion.
. Remove protective backing from decals.
. Position decals into place.
. With a soft squeegee, beginning from the center of
the decal, slowly and evenly press out excess foam
until you achieve a smooth finish.
5. Allow to set approximately 2 to 3 hours before handl-
ing. Maximum adherence is achieved in 48 to 72
hours.
> WN
6. Trim side decal to fit your cabinet.
CONTROL PANEL OVERLAY:
1. Refer to Recommended Control Panel Layout on
page 1.
2. Drill any new holes needed.
3. Plug any holes that will not be used. (A permanent
epoxy filler works well for this step.)
4. Pre-position the overlay prior to removing the back-
ing.
5. Slowly apply the overlay — inch by inch on the con-
trol panel, removing the backing as you apply it.
6. Once it's in place, by using an X-Acto knife, cut
around the button and joystick placements.
INSTRUCTION/BUTTON DECALS:
Apply the Player Instruction, Button and 1 Player/
2 Player decals in their respective positions. Apply
pressure liberally. Allow to set as long as possible
before putting game on location.
NOTE: Maximum adherence is achieved in 48 to 72
hours.
FCC WARNING LABEL:
FCC Warning Label must be applied to the outside of
the cabinet near the line cord entry.
MARQUEE
(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)
1/8” Acrylic Marquee should be cut to fit your game. DO
NOT remove protective mask until this is done.
One way of cutting your Marquee is as follows: (Be sure
to protect painted side of Marquee from any surface
which may scratch or mar finish).
CUTTING WITH A KNIFE OR SCRIBER
Acrylic sheet up to 3/16” thick may be cut by a method
similar to that used for cutting window glass. Use a
scriber of some kind — a scribing knife such as the one
pictured, a metal scriber, an awl, or even a sturdy craft
knife — to score the sheet. Draw the scriber several
times (7 or 8 times for a 3/16” thick piece) along a
straight edge held firmly in place. It is best not to
remove the protective masking. Make the cuts carefully
using firm, even pressure. For best results make each
stroke cleanly off the edge of the sheet.
Then clamp the acrylic sheet or hold it rigidly under a
straight edge with the scribe mark hanging just over the
edge of a table. Protect your hands with a cloth, and ap-
ply a sharp downward pressure to the other side of the
sheet. It will break along the scratch. Scrape the edges
to smooth any sharp corners. This method is not recom-
mended for long breaks or thick material.
Break sheet over edge of
table after scribing.
Always draw the scribing
knife along a straight edge.
P.C.B. CAGE INSTALLATION
Konami, inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation.
The cage is made of a 32 point stem-stock which is fire retardant.
TO INSTALL THE CAGE:
1. Open cage bottom and secure to desired P.C.B. position.
2. Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
3. Close the cage over printed circuit board and secure with latch on cage.
2
JAILBREAK: MONITOR SPECIFICATIONS
JAILBREAK requires a horizontally mounted monitor. It also generates composite negative sync. If your monitor is
composite positive sync, you will have to change to composite negative sync.
(1) To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the
output pin from the P.C.B. is a combination of H-sync and V-sync.
NOTE: Please refer to Figure 2.
FIGURE2 <
+5V a
7404 or 74LS04
lg
FROM P.C. BOARD 41 2
NEGATIVE COMPOSITE SYNC. | GND OUTPUT TO MONITOR
(PIN 14 on P.C.B EDGE) — POSITIVE COMPOSITE SYNC.
(+ 5V and GND should be taken out of the P.C. Board.)
(2) Separate Sync modification for JAILBREAK if your monitor has “Separate Sync” input. (For example
“Electrohome brand” and Wells-Gardner brand.”)
Step 1
WIRING HARNESS
N [12
P 113
R [14
S
15
If the picture is still not stable...
Step 2
Prepare Hook-up wire to seperate -H and -V sync. signals.
WIRING HARNESS
N 112
i
i
I
DE = NEGATIVE SYNC INPUT
1
НЕМ NEGATIVE SYNC INPUT
MONITOR BOARD
VIDEO SYNC
PE ED TE EE a aE EE.
Tra] VIDEO SYNC
$ 15
pP
PWB300394
JAILBREAK: MONITOR INFO.
SERVICE INSTRUCTIONS
NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every
time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis
become magnetized it will be necessary to degauss the atfected area with a manual degaussing coil. Move
the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6
feet before turning off.
1.0 BLACK LEVEL CONTROL ADJUSTMENT
This control has been set at the factory and should not
need further attention, however, when the game is con-
nected a slight adjustment of VR201 may be necessary to
obtain the proper black level (the black portion of the
picture just extinguished).
2.0 VERTICAL SIZE (HEIGHT)
Location of this control is shown in Fig. 1. This control
must be adjusted slowly, if necessary, until the picture or
test pattern attains the correct vertical proportions.
3.0 CIRCUIT PROTECTION
A 4.0A pigtail fuse, mounted on the Main Board has been
provided to protect the Power Output Circuit.
4.0 FOCUS
Adjust the focus control, located on the HV unit (1352),
for maximum over-all defination and fine picture detail.
5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT,
VR351 (See Fig. 1)
A warm-up period of at least five minutes should be
allowed before alignment is carried out. With the monitor
being driven from the game signal, short TP601 to TP31.
Adjust VR351 until the picture stops sliding horizontally.
Remove the short.
6.0 HORIZONTAL VIDEO POSITION
If the video is off center on the raster some compensa-
tion can be made by adjusting this control.
7.0 VERTICAL RASTER
POSITION ADJUSTMENT
If the video is off center vertically, (short dimension of
picture tube) some compensation can be made by mov-
ing the vertical raster position adjustment jumper to
either positions “U” or “D”.
8.0 HORIZONTAL RASTER
POSITION ADJUSTMENT
If the video is off center horizontally (long dimension of
the picture tube) some compensation can be made by
moving the horizontal raster position adjustment jumper
to either positions “R” or “L”.
9.0 HORIZONTAL WIDTH ADJUSTMENT
The horizontal width coil is a hexagonal tuning tool ad-
justment. This control must be adjusted slowly, if
necessary, until the picture or test pattern attains the
correct horizontal proportions.
“= „с a
* KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC.
USE THE THREE PIN CONNECTOR ON THE MONITOR.
REO CUTOFF
GRN CUTOFF’
BLU CUTOFF
*NEG H SYNC
* NEG V SYNC
*GND
POS H SYNC
POS V SYNC
—
GND _
BLU |
GRN |
"Eo
DRIVE DRIVE
NOTE.
WHEN USING COMPOS-
ITE SYNC USE HORIZ.
SYNC INPUTS,
HORIZ.
WIDTH
COIL
HORIZ HOLD
BLK LEVEL
A fore
TPEO!
FOCUS
L R
SCREEN
U D
In “JA
7 | Г ;
HORIZ VERT VERT VERT HORIZ *
CENTERING SIZE HOLD RASTER RASTER
SHIFT SHIFT
FIGURE 1
JAILBREAK: WIRING HARNESS
WIRE COLOR KEY: Solder Side — — Parts Side
(EMPTY) | A 1 + 12V DC ORANGE
RED/GREEN SPEAKER OUT | B 2 | SPEAKER OUT ORANGE/GREEN
RED/YELLOW *2P SHOOT | C 3 |2P SELECT" ORANGE/YELLOW
BROWN/YELLOW *2P LEFT | D 4 |2PRIGHT* BLUE/YELLOW
VIOLET/WHITE 1P START | E 5 | 2P START VIOLET/YELLOW
ORANGE/WHITE 1P SELECT | F 6 |2PUP* BLACK/YELLOW
RED/WHITE 1P SHOOT | H 7 | SERVICESW ORANGE/GRAY
BLUE/WHITE 1P RIGHT | J 8 |1PLEFT BROWN/WHITE
BLACK/WHITE 1PUP | K 9 |2PDOWN* GRAY/YELLOW
RED/GRAY COIN 1 | L 10 | COIN2 BLUE/GRAY
GRAY/WHITE 1P DOWN | M 11 | COIN COUNTER 1 GREEN/GRAY
WHITE/PINK (NOT USED) | N 12 | COIN COUNTER2 YELLOW/GRAY
GREEN/BROWN VIDEO GREEN | P 13 | VIDEO BLUE BLUE/BROWN
RED/BROWN VIDEORED | R 14 | VIDEO SYNC WHITE/BROWN
(EMPTY) | S 15 | (NOT USED) Y ELLOW/PINK
BLACK GND | T 16 | GND BLACK
BLACK GND | U 17 | GND BLACK
RED + 5VDC | у 18 | + 5VDC RED
* Cocktail Table or Dual Control
Upright Only
(BASE COLOR/LINE COLOR)
IMPORTANT INSTALLATION NOTICE FOR JAILBREAK
The solid red heavy guage wires on the edge connector must be inserted at position A18 & B18, as shown in the
diagram below. *Reverse condition will result in board damage!
[e
DZ
B18 B1
ROM 7 ROM 4
ROM 8 ROM 5
ROM 9 ROM 6
SOUND
PROCESSOR
ROM 1 ©
CUSTOM a
|
ROM 2
ROM
RAM OM 3 CPU
HILId HIN! 28/5
YOLIINNO? 3903
AS+
AS+
IND
IND
UND
UND
die
3NAS
NIE
3173
2 YIFINACD NIOD
NMOT el
1 EFL1NNO2 NIOJ
I NOD
c NICD
dN 4!
NAMOT de
HDI di
1131 di
100HS di
21835
193735 di
* d de
17:58 dí
JéFIS cC
1-31 al
1494 сё
JOOHS de
* 1937358 de
MO E=XMF3dS
INO EMV dS
+
* »* +
ACT
o
—
q
es
——
| |
©
N
ry
mm
DD
|
WO
E
One
>
—>“u
TS 30105 —
—= ут ‘
2013 7
2 |
= IY
3)
|__|
N
A
(VEAS +
NI
Ле! +
A1ddfIS
dIM0d
0
ii
x
8IINNOINIOD ACI
—
¥3.N0J NID A
EF.
INAS
N3349
3n78
HOLINOW
40703
ÁJuUO JUBIJAN
|0J3U0D [BN 10 8IqeL HEP009,
97d 94) UC parorsur
431/NN0I
№02 10] sapoip 18)}14 aBins — (7)
19hoid 20N de
Ao) ON dí (1)
di 19
— SILLON —
S 10#1N07
NMOQ di
dh di
LHIl# di
Пе ВЕ
1437 di
100HS di
193138 dl
*
NAOG de
f
5
dh
1437
HOY o——
ей,
LOOHS
193735 0—0 Ö
т т
|
Do
oe
18718 IWY9I di
——
LULL
О © HILIMS IIS
©
* dil 42
18Y1S di
19v1S de
1H9/4
1431 de
de
+ | * | * | *
100HS de
1931735 de
de 10)
IdAl 31971
S1041NO07 dí
18YL1S 3NV9 de
et —
ST04INOD
10/ Ajuo
SD oWDS
— = 4
—
ALIOVeVD EMId (34100 3d
ACI+ В /
19 U9
Eo
MITE MIU
>»
MCI MES?
Ve Ve
FIN dd INTA
WVHOVIA DNIHIM
AVIHaIIvr
MN
JAILBREAK: TECHNICAL INFORMATION
(1) Required Power Capacity
+5V DC 3A or more.
+ 12V DC See Figure 1 below
Figure 1: W
SPEAKER | 8Q ew 8NEW BREW TT 12W _ 49
Required
Power 12V 1A 12V 2A 12V 2A Not Applicable
Capacity
(2) Signal output ——— 1
R(red) analog, positive _
G(green) analog, positive |
B(blue) analog, positive Vi uu a
Sync. H-V composite negative A
DIAGNOSTIC PROCEDURES
AUTOMATIC SELF-TEST — Upon “Power On”, this system will automatically test ROMS and VIDEO RAMS. The
screen will display pass or fail conditions as follows:
TEST PASSED TEST FAILED IF TEST FAILS
RAM 1 OK RAM 1 BAD ВАМ 1 = 11E
ВАМ 2 ОК RAM 2 BAD RAM2 = 8E
ROM 1 OK ROM 1 BAD ROM 1 = 11 D
ROM 2 OK ROM 2 BAD ROM 2 = 9D
DIP SWITCH SETTINGS
DIP SW No. 1 Settings
Coin 1 Switch Set
Coin 2 Switch Set
SW 4 3 2 1 COIN | PLAY
e | OFF | OFF | OFF | OFF | 1 1
OFF ON 1 2
ON OFF 1 3
ON ON 1 4
OFF ON OFF | OFF 1 5
OFF ON 1 6
ON OFF 1 7
ON ON 2 1
ON OFF | OFF | OFF 2 3
OFF ON 2 5
ON OFF 3 1
ON ON 3 2
ON ON OFF | OFF 3 4
OFF | ON 4 1
ON OFF 4 3
ON ON FREE PLAY
DIP SWITCH NO. 2 SETTINGS
THE NUMBER OF PLAYER'S LIFE
SW 1 2 NUMBER
OFF | OFF 1
ON OFF 2
o OFF ON 3
ON ON 5
CHANGE OF TABLE OR UP-RIGHT
SW 3 TYPE
OFF TABLE
e | ON UP-RIGHT
BONUS SET
SW 4 FIRST BONUS SECOND
e OFF 30,000 Every 70,000
ON 40,000 Every 80,000
Difficulty of the Game
SW 5 6 DIFFICULTY
OFF | OFF EASY
ON | OFF NORMAL
. OFF | ON DIFFICULT
ON | ON VERY DIFFICULT
SW 8 7 6 5 COIN | PLAY
o OFF | OFF | OFF | OFF 1 1
OFF | ON 1 2
ON | OFF 1 3
ON ON 1 4
OFF | ON | OFF | OFF 1 5
OFF | ON 1 6
ON | OFF 1 7
ON ON 2 1
ON | OFF | OFF | OFF 2 3
OFF | ON 2 5
ON | OFF 3 1
ON ON 3 2
ON ON | OFF | OFF 3 4
OFF | ON 4 1
ON | OFF 4 3
ON ON | INVALIDITY
SOUND IN ATTRACT MODE
SW 8 SOUND
OFF OFF
° ОМ ОМ
*SW 7 NOT USED
DIP SWITCH NO. 3 SETTINGS
Video Screen Flip
SW 1
o OFF NORMAL
ON UPSIDE DOWN
Single/Dual Control Upright
SW 2 TYPE
o OFF SINGLE UPRIGHT CONTROL
ON DUAL UPRIGHT CONTROL
*SW 3 & SW 4: NOT USED
* SHOWS NORMAL SETTING
USER INFORMATION
WARNING
F.C.C. REGULATION COMPLIANCE
THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED-
VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983
WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE-
QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A
COMPUTING DEVICE.
IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO
ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED
FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER-
FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE
OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY
TO CORRECT THE INTERFERENCE.
THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION
KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT
THE TIME OF INSTALLATION.
IGonamic
1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007
TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW
">