TNT 72704 air compressor Operator's Manual
The TNT 72704 is a 3-gallon oil-free air compressor designed for a variety of tasks around the home, garage, or workshop. The compressor features a 1/3 horsepower motor and a single-cylinder pump for reliable operation. It is also equipped with a 25-foot recoil air hose, a variety of accessories, and a pressure regulator to control output air pressure.
Advertisement
Advertisement
3-GALLON OIL-FREE
AIR COMPRESSOR
Operator's Manual Model:
Model 72704
TOLL FREE HELPLINE: 1-888-266-7096
FOR SAFE OPERATION, READ AND UNDERSTAND
ALL CONTENTS OF THE INSTRUCTION MANUAL
1
TABLE OF CONTENTS
SPECIFICATIONS..........................................................................................
SAFETY GUIDELINES ..................................................................................
2
3
IMPORTANT SAFETY INSTRUCTIONS ....................................................... 3
GENERAL SAFETY RULES...........................................................................
9
SPECIFIC SAFETY RULES............................................................................11
GLOSSARY OF TERMS.................................................................................
12
ASSEMBLY.....................................................................................................
13
INSTALLATION...............................................................................................
19
OPERATION...................................................................................................
21
MAINTENANCE .............................................................................................
26
TROUBLESHOOTING....................................................................................
27
EXPLODED VIEW/PARTS LIST.....................................................................
29
LIMITED WARRANTY ....................................................................................
32
SPECIFICATIONS
Model No.: 72704
Motor.................................................................................120V 60Hz, 2.2-amp
Running Horsepower...............................................................................1/3 Hp
Tank Size...............................................................................................3-gallon
Pump Type..................................................Single Cylinder: Shaft direct drive
Air Hose Type.............................................................25’recoil, MAX. 100 PSI
Air Delivery...................................................................... 1.0 SCFM @ 40 PSI
0.6 SCFM @ 90 PSI
Cut-in Pressure........................................................................................85 PSI
Cut-out Pressure....................................................................................100 PSI
Max. Pressure........................................................................................100 PSI
Power Cord.....................................................................6ft, 3-prong, 18 AWG
2
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and
PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided,
will
result in
death or serious injury
.
hazardous situation which, if not avoided, could result in death or
serious injury.
Indicates a potentially
Indicates a potentially hazardous situation which, if not avoided,
may
result in
minor or moderate injury.
Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided,
may
result in
property damage.
IMPORTANT SAFETY INSTRUCTIONS
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are: lead from lead-based paints crystalline silica from bricks and cement and other masonry products arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear
MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
When using air tools, basic safety precautions should always be followed to reduce the risk of personal injury.
3
IMPORTANT SAFETY INSTRUCTIONS
Save these instructions
Improper operation or maintenance of this product could result in serious injury and property damage. Read and understand all warnings and operation instructions before using this equipment.
HAZARD
WARNING: Risk of explosion or fire
What Could Happen
It is normal for electrical contacts within the motor and pressure switch to spark.
How To Prevent It
Always operate the compressor in a well ventilated area free of combustible
materials, gasoline, or solvent vapors.
If electrical sparks from compressor
come into contact with flammable vapors, they may ignite, causing fire or explosion.
Restricting any of the compressor
ventilation openings will cause serious overheating and could cause fire.
Unattended operation of this product
could result in personal injury or property damage. To reduce the risk of fire, do not allow the compressor to operate unattended.
If spraying flammable materials, locate
compressor at least 20 feet away from
spray area. An additional length of hose may be required.
Store flammable materials in a secure location away from compressor.
Never place objects against or on top
of compressor. Operate compressor in an open area at least 12 inches away
from any wall or obstruction that would restrict the flow of fresh air to the ventilation openings.
Operate compressor in a clean, dry well ventilated area.
Always remain in attendance with the product when it is operating.
Always disconnect electrical power by moving pressure switch lever to the off position and drain tank daily or after each use.
4
HAZARD
WARNING: Risk of Bursting
Air Tank: The following conditions could lead to a weakening of the tank, and result in a violent tank explosion and could cause property damage or serious injury.
What Could Happen
1.
Failure to properly drain condensed water from tank, causing rust and thinning of the steel tank.
How To Prevent It
Drain tank daily or after each use. If tank develops a leak, replace it immediately with a new tank or replace the entire compressor.
2. Modifications or attempted repairs to the tank.
3.
Unauthorized modifications to the unloader valve, safety valve, or any other components which control tank pressure.
4.
Excessive vibration can weaken the air tank and cause rupture or explosion
ATTACHMENTS & ACCESSORIES:
Exceeding the pressure rating of air
tools, spray guns, air operated accessories, tires, and other inflatables
can cause them to explode or fly apart, and could result in serious injury.
Never drill into, weld, or make any
modifications to the tank or its attachments.
The tank is designed to withstand specific operating pressures. Never make
adjustments or parts substitutions to alter the factory set operating pressures.
For essential control of air pressure, you
must install a pressure regulator and pressure gauge to the air outlet (if not
equipped) of your compressor. Follow the equipment manufacturers recommendation and never exceed the maximum allowable pressure rating of attachments. Never use compressor to
inflate small low pressure objects such as children’s toys, footballs, basketballs, etc.
HAZARD
WARNING: Risk from Flying Objects
WHAT CAN HAPPEN
The compressed air stream can cause
soft tissue damage to exposed skin and
can propel dirt, chips, loose particles, and small objects at high speed, resulting in property damage or personal injury.
5
HOW TO PREVENT IT
Always wear ANSI Z87.1 approved
safety glasses with side shields when using the compressor.
Never point any nozzle or sprayer
toward any part of the body or at other
people or animals.
Always turn the compressor off and
bleed pressure from the air hose and tank before attempting maintenance, attaching tools or accessories.
HAZARD
WARNING: Risk of Electric Shock
WHAT CAN HAPPEN
Your air compressor is powered by
electricity. Like any other electrically powered device, If it is not used properly
it may cause electric shock.
Repairs attempted by unqualified
personnel can result in serious injury or death by electrocution.
HOW TO PREVENT IT
Never operate the compressor outdoors
when it is raining or in wet conditions.
Never operate compressor with
protective covers removed or damaged.
Any electrical wiring or repairs required on this product should be performed by
authorized service center personnel in accordance with national and local electrical codes.
Electrical Grounding: Failure to provide
adequate grounding to this product could result in serious injury or death from electrocution.
See grounding instructions.
Make certain that the electrical circuit
to which the compressor is connected
provides proper electrical grounding, correct voltage and adequate fuse protection.
HAZARD
WARNING: Risk to Breathing
WHAT CAN HAPPEN
The compressed air directly from your compressor is not safe for breathing.
The air stream may contain carbon
monoxide, toxic vapors, or solid
particles from the tank. Breathing these
contaminants can cause serious injury
or death.
Sprayed materials such as paint, paint solvents, paint remover, insecticides, weed killers, may contain harmful vapors
and poisons.
HOW TO PREVENT IT
Air obtained directly from the compressor
should never be used to supply air for
human consumption. In order to use air produced by this compressor for breathing, suitable filters and in-line
safety equipment must be properly
installed. In-line filters and safety
equipment used in conjunction with the compressor must be capable of treating
air to all applicable local and federal codes prior to human consumption.
Work in an area with good cross
ventilation. Read and follow the safety
instructions provided on the label or safety data sheets for the materials you
are spraying. Use a NIOSH/ MSHA
approved respirator designed for use with your specific application.
6
come into contact with you or your clothing.
7
HAZARD
WARNING: RISK OF SERIOUS INJURY OR PROPERTY
DAMAGE WHEN TRANSPORTING COMPRESSOR
(Fire, Inhalation, Damage to Vehicle Surfaces)
WHAT CAN HAPPEN
Oil can leak or spill and could result in fire or breathing hazard; serious injury or death can result. oil leaks will damage carpet, paint or other surfaces in vehicles or trailers.
HOW TO PREVENT IT
Always place COMPRESSOR on a
protective mat when transporting to protect against damage to vehicle from leaks. Remove COMPRESSOR from vehicle immediately upon arrival at your destination.
HAZARD
WARNING:
RISK OF UNSAFE OPERATION
WHAT CAN HAPPEN
Unsafe operation of your air compressor
could lead to serious injury or death to you or others.
HOW TO PREVENT IT
Review and understand all instructions and warnings in this manual.
Become familiar with the operation and
controls of the air compressor.
Keep operating area clear of all persons, pets, and obstacles.
Keep children away from the air compressor at all times.
Do not operate the product when
fatigued or under the influence of alcohol or drugs. Stay alert at all times.
Never defeat the safety features of this product.
Equip area of operation with a fire extinguisher.
Do not operate machine with missing, broken, or unauthorized parts.
8
GENERAL SAFETY RULES
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power
tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. do not
change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull the Plug from an outlet. keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords
immediately. Damaged Power Cords increase the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock.
PERSONAL SAFETY
Stay alert. watch what you are doing, and use common sense when operating a power tool. do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Dress properly. do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
9
GENERAL SAFETY RULES
Avoid accidental starting. be sure the Power Switch is off before
plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Always wear ANSI-approved safety goggles and a dust mask/respirator when using or performing maintenance on this tool.
TOOL USE AND CARE
Use clamps (not included) or other practical ways to secure and support
the work piece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
Do not force the tool. use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
Do not force the tool and do not use the tool for a purpose for which it is not intended.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced.
Disconnect the Power Cord Plug from the power source before making
any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users. Keep children away from.
Maintain tools with care. Properly maintained tools are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may become hazardous when used on another tool.
SERVICE
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a risk of injury.
10
SPECIFIC SAFETY RULES
Maintain labels and nameplates on the Air Compressor. These carry important information. If unreadable or missing, contact toll free helpline:
1-888-266-7096 for a replacement.
Always wear ANSI-approved safety impact eye goggles and heavy work
gloves when using the Air Compressor. Using personal safety devices reduce the risk for injury. Safety impact eye goggles and heavy work gloves are available from SEARS CANADA.
Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use a power tool in areas near flammable chemicals, dusts, and vapors. Do not use this product in a damp or wet location.
Avoid unintentional starting. Make sure you are prepared to begin work before turning on the Air Compressor.
Do not force the Air Compressor. This tool will do the work better and safer at he pressure and capacity for which it was designed.
Always unplug the Air Compressor from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
Before each use, check all nuts, bolts, and screws for tightness. Vibration may cause these to loosen.
Drain compressor every day. Do not allow moisture to build up inside the compressor.
Make sure all equipment is rated to the appropriate capacity. Adjust the output air pressure to the tool’s operating capacity.
Avoid explosions and fire. Never place flammable objects near the compressor. Never spray water or any flammable liquids towards the compressor.
Avoid bodily injury. Never direct the air outlet at persons or animals.
Never leave the air tool unattended when it is plugged into the air
compressor. Turn off the tool, and unplug it from air compressor outlet before leaving.
WARNING! People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker.
11
GLOSSARY OF TERMS
Become familiar with these terms before operating the unit.
CFM: Cubic feet per minute.
SCFM: Standard cubic feet per minute; a unit of measure of air delivery.
PSI: Pounds per square inch ; a unit of measure of pressure.
Code Certification: Products that bear one or more of the following marks:
UL, CUL, ETL, CETL, have been evaluated by OSHA certified independent safety laboratories and meet the applicable Underwriters Laboratories
Standards for Safety.
Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called "cut-in" pressure.
Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called "cut-out" pressure.
Branch Circuit: Circuit carrying electricity from electrical panel to outlet.
DUTY CYCLE
Air compressors should be operated on not more than a 50% duty cycle. This means an air compressor that pumps air more than 50% of one hour is considered misuse, because the air compressor is undersized for the required air demand. Maximum compressor pumping time per hour is 30 minutes.
ACCESSORIES INCLUDED
Includes: 25' Recoil air hose, Inflation Needle, Tapered Blow Gun Nozzle,
Blow Gun Adapter, Blow Gun Safety Nozzle, Blow Gun, Tire Chuck, ¼”Male
Quick-Connect Plugs, PTFE - Thread Seal Tape, ¼” Female Quick-Connect
Body and 2” Brad Nailer.
12
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Carefully remove the tool and any accessories from the box. Mark sure that all items
listed in the packing list are included.
Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
Do not discard the packing material until you have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please call 1-888-266-7096 for assistance.
PACKING LIST
Air Compressor
Accessories (11)
Operator’s Manual (not shown)
1
Includs:
1 air compressor
2 2” Brad Nailer
3 25' Recoil air hose
4 Inflation Needle
5 Tapered Blow Gun Nozzle
6 Blow Gun Adapter
7 Blow Gun Safety Nozzle
8 Blow Gun
9 Tire Chuck
10 ¼”Male Quick-Connect Plugs
11 PTFE - Thread Seal Tape
12 ¼” Female Quick-Connect Body
13 Operator’s Manual (not shown)
2
4
5
6
7
3
11
8
9
10
12
13
ASSEMBLY
Make sure the Power Switch of the tool is in its “Off” position and that the tool is unplugged from its electrical outlet, and all air pressure is released before making any adjustments to the tool.
1. Close the Drain Valve under the Tank by turning it clockwise until it stops.
2. Connect the high pressure air hose to the air outlet.
The outlet is 1/4” x 18 NPT. For easy connection or removal, a quick coupler should be installed on the end of the air outlet.
3. To extend the life of most air tools, it is recommended to install an oiler and water filter in series with the air output line of the Air Compressor as shown below.
4. Connect the other end of the high pressure air hose to the air tool.
Do not remove or try to adjust the factory sealed Pressure
Controller; removal can cause the Tank to over pressurize and explode.
(Brad Nailer)
14
ASSEMBLY
Attaching Air Hose To Compressor
1.
2.
Using your left hand push quick connect towards the body of the compressor.
Firmly press fit the male quick connect portion on the air hose into the female quick connect and release female quick connect locking hose in place.
NOTE: When connecting or disconnecting air hose remove air from tank.
Fig. A
15
ASSEMBLY
Assemble Accessories
The unit is supplied with an accessory kit and inflator/deflator kit, choose the accessory needed.
Assemble Accessory Kit
(See Fig. B)
1. Assemble female tire chuck (a) to hose (b) and tighten securely with wrenches.
To Assemble Accessories
1. Attach the blow gun (c) to hose (b).
Risk of unsafe operation. If an accessory is not being used with the blow gun, the safety nozzle MUST be assembled.
2. Assemble the safety nozzle (d) or blow gunadapter (e) to blow gun.
NOTE:To use the inflating needle (f) or the tapered inflator (g), need to use the blow
gun adapter (e) to assembled to the blow gun
3. Attach the inflation needle(f) to the blow gun adapter on the blower gun.
g a f e b c d
Fig. B
16
ASSEMBLY
Assembling Inflation Needle Or Tapered Nozzle
The blow gun (c) and blow gun adapter (e) from the accessory kit is needed to use the inflator/deflator kit. (See Fig. C/Fig. D)
1. Attach the blow gun to hose.
2. Attach blow gun adapter to blow gun.
3. Attach the inflation needle (f), tapered nozzle (g).
Safety Nozzle
g e f c
Fig. C
Fig. D
17
ASSEMBLY
Quick-Connect
(See Fig. E)
1. Assemble the 1/4” female quick-connect plug (k) to the 1/4” Female quick-connect body (l).
2. Attach the quick-connect plug to the hose.
k l
PULL
Fig. E
NOTE: Always use PTFE tape on all threaded components, to prevent leaks.
18
INSTALLATION
GROUNDING INSTRUCTIONS
DANGER! Risk of Electric Shock. In the event of a short circuit, grounding reduces the risk of shock by providing an escape wire for the electric current. This air compressor must be properly grounded.
The portable air compressor is equipped with a cord having a grounding wire with an appropriate grounding plug (see following illustrations). The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances.
1. The cord set and plug with this unit contains a grounding pin. This plug MUST be
used with a grounded outlet.
IMPORTANT: The outlet being used must be installed and grounded in accordance with all local codes and ordinances.
2. Make sure the outlet being used has the same configuration as the grounded plug.
DO NOT USE AN ADAPTER. (See illustration)
3. If these grounding instructions are not completely understood, or if in doubt as to
whether the compressor is properly grounded, have the installation checked by a
qualified electrician.
Risk of Electric Shock. IMPROPER GROUNDING CAN RESULT IN ELECTRICAL
SHOCK. Do not modify the plug provided. If it does not fit the available outlet, a correct outlet should be installed by a qualified electrician. Repairs to the cord set or plug MUST be made by a qualified electrician.
Plug
Grounding pin
3-Prong Plug and Outlet
Grounded
Outlets
19
INSTALLATION
EXTENSION CORDS
Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage.
(See Table A.)
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required.
(See Table
A.)
If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size.
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
TABLE A
RECOMMENDED MINIMUM WIRE GAUGE FOR (120 OR 240 VOLT)
EXTENSION CORDS*
NAMEPLATE AMPERES
(at full load)
0 – 2.0
2.1 – 3.4
3.5 – 5.0
25 Feet
18
18
18
EXTENSION CORD LENGTH
50 Feet
18
18
18
75 Feet
18
18
16
100 Feet 150 Feet
18 16
16
14
14
12
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
18
18
14
12
16
14
12
10
14
12
10
-
12
10
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
12
-
-
-
20
OPERATION
KNOW YOUR AIR COMPRESSOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Tank Air
Pressure Gauge
Overload Protector
Power Switch
Air Release
Safety Valve
Pressure
Adjustment
Output Air
Pressure
Gauge
Quick-connect
Coupler
Air Outlet
21
OPERATION
OPERATING COMPRESSOR
TURNING COMPRESSOR ON
1. Pull and release the Air Release Safety Valve to verify it does not stick.
2. Plug the power cord into a grounded electrical outlet.
3. Press the Power Switch to the On position.
4. Allow the Tank to fill to 85 PSI before using.
With the Air Compressor turned on, operation is automatic and under the control of the internal Pressure Controller.
PRESSURE ADJUSTMENT
Set the appropriate air pressure output for the air tool being used.
1. Turn the Pressure Adjustment knob to the left to decrease output air pressure, or to the right to incease the output air pressure.
2. Read the air output pressure on the Output Air Pressure Gauge.
USING THE AIR RELEASE SAFETY VALVE
The Air Release Safety Valve is used when tank decompression is needed quickly and efficiently.
1. Press the Power Switch to the Off position.
2. Pull on the Air Release Safety Valve ring to release pressure from the Tank.
3. When all pressure is released, let go of the ring on the Air Release Safety
Valve.
EMPTY AIR AND CONDENSATION
The water Drain Valve is located underneath the Air Tank. It must be used daily to release all trapped moisture through this valve. It will also get rid of any condensation that may cause tank corrosion.
Slightly open the water Drain Valve to blow air and moisture out of the Tank. Opening it all the way may cause it to be blown off.
1. Press the Power Switch to the Off position.
2. Unscrew the water Drain Valve two to three turns counterclockwise.
3. When all the moisture is released, turn the Drain Valve clockwise until it is tight.
22
OPERATION
OPERATING BRAD NAILER
Always disconnect the tool from the air supply before loading. When loading the tool always aim the tool away from yourself and others. Make sure that the trigger is not pressed while the tool is being loaded.
1. Press the magazine release button to open the magazine.(See Fig. F)
2. Slide the magazine open and insert a strip of fasteners.(See Fig. G)
3. Push the magazine closed from the bottom. Make sure the nails slide freely in the magazine. (See Fig. H)
4. The magazine should lock closed. If it does not, open and make sure the nails are flat against the tray of the magazine.
5. Connect the tool to the air supply. Make sure the air supply is in the correct
PSI range (see Operating Instructions).
6. Never operate the tool unless the tip of the nailer is in contact with the workpiece. Do not operate the tool without fasteners loaded or damage to the tool may result.
Release
Button
Fig. F Fig. G
Fig. H
23
OPERATION
IMPORTANT:
Never exceed the maximum or minimum pressure. Pressure that is too low or too high may cause excess noise, wear, and/or misfiring.
When connecting the air supply, keep hands and body away from the discharge area of the nailer.
A filter regulator/oiler is required and should be located on the air line as close to the tool as possible.
Keep the air filter clean. A dirty filter will reduce the air pressure supplied to the tool causing a reduction in power and efficiency.
For better performance, install quick-connectors on your tool and a quick coupler on the air hose.
For the best performance, make sure all connections in the air supply are tightly sealed to prevent air loss.
24
OPERATION
USING THE TIRE PRESSURE GAUGE
Place the tire gauge opening on the valve stem of the tire and firmly hold in place for at least 2 seconds. If required check twice for accuracy.
The side wall of your tire will specify the maximum PSI or KPA rating however the pressure level for everyday driving will be specified in your vehicles manual and should be followed. It is suggested to review your vehicles owners manual for optimum tire pressure by season or contact your tire manufacturer for more details.
NOTE: Check tire condition and pressure at least once a month and before any long trip. Never exceed the maximum cold tire inflation pressure shown on the tire side wall. The tire pressures should be checked when the tires are cold. On hot days the pressures will be 4 to 8 psi (28 - 50 KPA) higher after high speed driving.
NOTE: The Tire Gauge is NOT INCLUDED in the accessories.
USING THE TIRE CHUCK
1. Connect tire chuck to hose using PTFE tape on threads. You may also attach the tire chuck to a male quick connect for quick and easy removal in the future.
2. Connect hose to compressor and turn switch to ON position. Allow pressure to build up to maximum pressure level in tank.
3. Adjust regulator pressure to MAXIMUM position. In maximum output pressure position 135psi the tire will fill up quicker and accurately however it is extremely important to monitor the air flow using the tire gauge as it is in process of being filled to ensure of not overfilling tire. NOTE: If maximum pressure is not used for output of the compressor to tire than the tire may not fill as there may be a pressure lock between the tire and the hose which is normal. Due to this always use maximum pressure from compressor and continue to monitor pressure with gauge.
4. Place tire chuck on tire valve stem and press firmly into place to prevent air from leaking out of tire.
5. Remove tire chuck from valve stem and check pressure using a tire gauge.
This process needs to be followed throughout the process of filling each tire to ensure of accuracy and to prevent overfilling..
25
MAINTENANCE
MAINTENANCE OF COMPRESSOR
Make sure the Power Switch of the tool is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
1.
BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use.
Do not use damaged equipment.
2. Purge the Air Tank daily of all air and condensation to prevent corrosion.
3. Store the Air Compressor in a clean and dry location.
4. Check all air fittings for leaks before using.
MAINTENANCE OF BRAD NAILER
Disconnect the tool from the air supply before performing any adjustments, cleaning, maintenance, or repair.
• Regular lubrication should be performed if your tool is used without an in-line automatic oiler. Place 2–6 drops of air tool oil into the air inlet before each workday and after every 2 hours of continuous use.
• Check all connections and o-rings. Change all worn or damaged o-rings, seals, etc. Tighten all the screws and caps to prevent potential damage or injury.
• Inspect the trigger and safety mechanisms to ensure they are working properly.
Check for loose or missing parts, binding, and/or sticking parts and adjust or replace accordingly.
• Keep the nail magazine and the firing tip of the tool clean and free of any foreign particles or objects.
26
TROUBLESHOOTING
TROUBLESHOOTING OF COMPRESSOR
Problem
Air Compressor will not start
Tank air pressure does not reach 90 PSI and Air Compressor runs continuously.
Air tool not operating at proper speed.
Possible Causes
Power Switch in Off position.
No power at outlet.
Line cord not plugged in.
Air Leaking at Drain Valve.
Air hose has leak.
Air output pressure low.
Air hose has leak.
Probable Solutions
Push Power Switch to On position.
Check power at outlet.
Plug line cord into electrical outlet.
Tighten Drain Valve.
Tighten or repair air hose.
Adjust Pressure Adjustment knob so Air Output Pressure Gauge reads air tool’s proper operating pressure.
Tighten or repair air hose.
27
TROUBLESHOOTING
TROUBLESHOOTING OF BRAD NAILER
If any of the following problems arise during operation, stop using the tool immediately. Only a qualified technician or authorized service centre can perform repairs on this tool. Disconnect the tool from the air supply before any repair or adjustment. When replacing O-rings or cylinders, lubricate with air tool oil before reassembly.
Problem
Air leak near the top of the tool or in the trigger area
Air leak near bottom of tool.
Possible Causes
1. O-ring in trigger valve damaged.
2. Trigger valve head damaged.
3. Trigger valve stem, seal, or O-ring damaged.
Probable Solutions
1. Push Power Switch to On position.
2. Check power at outlet.
3. Plug line cord into electrical outlet.
1. Loose screws
2. Worn or damaged O-rings or bumper.
1.Tighten screws.
2. Check and replace O-rings and/or bumper.
Air leak between body and cylinder cap.
1. Loose screws.
2. Worn or damaged O-rings or seals.
Fasteners being driven too deep.
1. Worn bumper.
2. Air pressure is too high.
Too does not function well, does not drive fasteners, operates sluggishly.
1. Inadequate air supply.
2. Inadequate lubrication.
3. Worn or damaged O-rings or seals.
4. Exhaust port in cylinder head is blocked.
Tool skips fasteners
1. Worn bumper or damaged loading spring.
2. Dirt in front plate.
3. Dirt or damage is preventing fasteners from moving freely in the magazine.
4. Worn or dried-out O-ring on piston, or lack of lubrication.
5. Cylinder cover seal leaking.
1. Tighten screws.
2. Check and replace O-rings or seals.
1. Replace bumper.
2. Adjust air pressure.
1. Verify adequate air supply.
2. Place 2–6 drops of oil into air inlet to lubricate.
3. Check and replace O-rings or seals.
4. Consult Authorized service technician to replace internal parts.
1. Replace bumper or loading spring.
2. Clean drive channel on front plate.
3. Clean magazine.
4. O-ring needs to be replaced or lubricated.
5. Replace sealing washer.
Tool jams
1. Incorrect or damaged fasteners.
2. Damaged or worn driver guide.
3. Magazine or nose screw loose.
4. Magazine is dirty.
1. Change and use correct fasteners.
2. Check and replace the driver guide.
3. Tighten the magazine.
4. Clean the magazine.
28
Fig.1
EXPLODED VIEW/PARTS LIST
29
Fig. 2
EXPLODED VIEW/PARTS LIST
Fig. 3
30
EXPLODED VIEW/PARTS LIST
5
6
7
8
9
10
11
12
13
14
15
16
17
3
4
No Model Num.
1
2
3110252
3110752-1
3020252
3020152
3220250
3420350
3640152
3410552
3110152-1
3220840
3290651
3410302-1
3220475
3410352
3630252-2
3630150-2
3410452
Description
Motor Assy.
Pressure regulator Assy.
Copper connector knob
Copper hoop
Screw
Damping pad
Power cord
Cover, bottom
Circuit board
Screw
Washer
Wire clip
Screw
Cover, upper
Overload protector
Power switch
Tooling cover
4
4
1
1
1
Qty
1
1
2
2
1
1
1
2
1
1
1
1
COMPRESSOR (Fig. 1)
26
27
28
29
30
31
32
33
34
23
24
25
20
21
22
No Model Num.
18
19
3220404
3410652-1
3220552
3290408
3290250
3410329
3220575
3330152-5
3290275
3420150
3630152-1
3410152
3290252
3220150
3290750
3390250-1
3111352
Screw
Handle
Description
Screw
Flat washer
Spring washer
Zip tie
Screw
Air tank
Drain valve
Rubber foot
Pressure controller
Ball
Spring
Screw
Flat washer
Copper tube
Electric wire Assy.
No Model Num.
4
5
6
7
1
2
3
8
9
10
11
12
13
3610152
3320350
3220152
3210208
3310152
3420352
3490150
3490650
3290650
3310550
3310252
3490350-1
3310250
Description
Motor
Crank
Hex head screw
Bearing
Connecting rod
Silica gel ring
Piston ring
Paper pad
Hoop
Cylinder
Cylinder washer
Silica gel ring
Cylinder head
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
MOTOR (Fig. 2)
No Model Num.
17
18
19
20
21
14
15
16
22
23
24
25
3750150
3490350
3220610
3290305
3290706
3410350-1
3220205
3650101
3490552
3410150-1
3030150
3220650
Description
Copper connector
Silica gel ring
Screw
Flat washer
Spring washer
Fan
Screw
Flag terminal
Flag terminal bushing
Muffler board
Tube
Screw
No Model Num.
1
2
3
4
5
6
7
8
9
10
3310352
3420552
3340152-1
3420452
3420852
3750252
3420352-1
3420252
3340252
3330252
PRESSURE REGULATOR (Fig. 3)
Description
Pressure regulator
Seal ring
Spring
Seal ring
Rubber washer
Hex cap
Seal ring
Piston
Spring
Spring board
Qty
1
1
1
1
1
1
1
1
1
1
16
17
18
13
14
15
No Model Num.
11
12
3320252
3310452
19
20
3110852-1
3190350
3190352
3190252
3420652
3320452
3320352
3321175
Description
Hex spring cap
Pressure regulator cover
Pressure regulator knob
Safety valve
Pressure gauge
Pressure gauge
Seal ring
Nut
Connector
Male quick connect coupler
Qty
1
1
1
1
1
1
1
1
1
1
Qty
4
5
5
2
1
2
2
1
1
1
16cm
3
1
1
1
1
3
1
1
1
6
6
1
1
2
2
2
Qty
4
1
31
WARRANTY
For TWO YEARS from the date of purchase within Canada, SEARS CANADA will, at its option, repair or replace for the original purchaser, free or charge, any part or parts found to be defective in material or workmanship.
This warranty does not cover:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner's manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Full One Hundred Twenty Days Warranty on Normal Wear Parts: Normal wear parts are defined as blade adaptors, blades, grass bags and tires. These parts are warranted to the original purchaser to be free from defects in material and workmanship for a period of one hundred twenty (120) days from the date of retail purchase.
How to Obtain Service: Warranty service is available by calling the toll-free helpline, at 1-888-266-7096.The factory will not accept the return of a complete unit unless prior written permission has been extended by SEARS CANADA.
Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. The purchaser must pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by
SEARS
CANADA.
Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the sole and exclusive remedy of obligations arising from the sale of its products.
SEARS CANADA will not be liable for incidental or consequential loss or damage.
32
Download
Advertisement
Key features
Oil-free design
3-gallon tank
1/3 horsepower motor
Single-cylinder pump
25-foot recoil air hose
Various accessories
Pressure regulator
Frequently asked questions
The maximum output pressure is 100 PSI.
It is recommended to drain the air tank daily to prevent moisture buildup and corrosion.
The duty cycle of the TNT 72704 air compressor is 50%. This means that the compressor should be operated for no more than 30 minutes per hour.