R
Hardware Identification
Identification de la quincaillerie
7020-505 CLIMB SHELVING - TALL GABLE /
Supplier number
Num
/ 15955
Assembly Instructions
Instructions de montage
Before Assembly
1. Read through the instructions carefully before starting assembly.
2. Check the contents of the package. Contact the point of sale if you
find anything defective or missing.
3. Make sure that the indicated tools are available.
4. Assemble step by step as shown in the instructions.
5. It is a good idea to use a soft, protective underlay during assembly.
6. Do not use power tools at any stage of the assembly.
7. This product must be assembled by an adult.
Avant le montage
1. Lisez attentivement les instructions avant de commencer les travaux
de montage.
2.
ou manquantes, contactez le point de vente).
support souple.
6. Ne pas utiliser d'outils
de montage.
E (1)
H (2)
F (1)
7020-506 CLIMB SHELVING - SHORT GABLE /
G (2)
Y (1)
X (1)
I (1)
3" #2 Phillips / Phillips no 2, 3"
3" #3 Phillips / Phillips no 3, 3"
F (1) G (2) H (2)
1. Paint safe masking tape (blue)
2. Pencil
3. Tape measure
LEVEL - 48" / NIVEAU - 48 "
1. Ruban de peintre (bleu)
2. Crayon de blomb
7020-508 CLIMB SHELVING - L/R BRACKET /
1. Laser level
1. Niveau laser
CAUTION
EQ3 suggests that you install all gables onto wall studs. If using wall anchors please contact your local hardware store for suggestions on the wall anchors appropriate for your building type. EQ3 cannot recommend the wall anchors as there are many construction types.
ATTENTION
du mur. Si vous devez utiliser des ancrages, veuillez contacter votre vous conseiller sur le choix d'ancrages.
J (1)
7020-507 CLIMB SHELVING - EXTENSION BRACKET /
G (8)
K (1)
L (1)
7020-504 CLIMB SHELVING - DESK BRACKET /
G (6)
H (2)
M (1)
Please keep this assembly instruction in a safe place for future reference.
G (12)
1/12
7020-501-16 CLIMB SHELVING - NARROW SHELF /
A (1)
7020-502-16 CLIMB SHELVING - MID SHELF /
7020-503-16 CLIMB SHELVING - WIDE SHELF /
C (1)
7020-504-16-A CLIMB SHELVING - DESK SHELF /
B (1)
D (1)
SECTION 1: MOUNTING GABLE TEMPLATES - VERTICAL AND HORIZONTAL
1. Measure the height of your baseboard and record it in the box below. You can place the level flat on baseboard to help you get an accurate measurement.
SECTION 1: MONTAGE DES GABARITS VERTICAUX ET HORIZONTAUX
WALL / MUR
HEIGHT / HAUTEUR
2/12
2. Setup the laser level and project a line onto the wall where the installation is to take place. Measure from the floor to the line every 16", 32", or 48"
beginning where your first gable is to be installed and to each subsequent gable. Record the height on the assembly instructions in the area provided.
If a laser level is unavailable to you, you can accomplish this by placing a long piece of masking tape across the wall ensuring that it is level by using the 48" level.
d'un niveau de 48".
1
WALL / MUR
7020-503-16 CLIMB SHELVING - WIDE SHELF /
7020-501-16 CLIMB SHELVING - NARROW SHELF /
2
7020-504-16-A CLIMB SHELVING - DESK SHELF /
7020-502-16 CLIMB SHELVING - MID SHELF /
3
4
5
CHART 1 / GRAPHIQUE 1
1 2 3 4
5
6 7 8
Select the box with the lowest value - this will be the first gable you install. This is used to determine the highest point of the floor.
Cochez la case avec la valeu la plus faible - c'est ce montant que vous installerez en premier.
EXAMPLE / EXEMPLE
CHART 1 / GRAPHIQUE 1
1
2 3 4 5 6 7 8
25.5" 25.75" 25.25" 25.25" 25.0"
From the above measurements, the first gable that you will install will be gable #5 - the gable with the smallest measurement.
If any of the measurements are more than 1" apart you will need additional floor wedges/felt pads to complete the install due to the uneven nature of the floor.
**The reason is the first gable installed must be the gable that sits at the highest location on the floor. Failure to select the highest position on the floor for the first gable will result in gables that do not touch the floor, gables that are too high for the shelving to sit level or unneeded holes in the wall.
** des trous inutiles dans votre mur.
3/12
3. Cut the vertical template (Part X) off from the ground marking using the height measured in step 1 plus
1
8
" added to it. Only add the
1
8
" to the height if all your measurements are less than 1" in difference. If it will be greater, do not add the
1
8
".
Example: Baseboard measured 3", cut at 3
1
8
" on the template (Part X)
1
8
". Ajoutez ce
1
8
"
8
1
".
Exemple: Pour une plithe mesurant 3" de hauteur, coupez 3
1
8
" du gabarit.
4. Secure template to the wall in the spot selected in step 2 using masking tape, ensuring that the top line is level and that the bottom of the template is resting on the top of the baseboard. Once secured, ensure that the template is vertically straight as well as horizontally straight using the 48" level.
5
X
X
X
X
5. Secure the horizontal template (part Y) to the wall using masking tape, taking care to line up the mounting holes on part Y with the mounting holes on part X.
Use a laser level or box level to ensure that the horizontal template is level on the wall.
Once level on the wall, mark the gable (part E) positions 4 and 5 on the wall using a pencil. Be sure to mark the center of the hole where the screw/anchor will be inserted.
3
4
Y
5
X
4/12
6. Secure the next horizontal template (part Y) to the wall with masking tape taking care to line up the mounting holes on part Y with the last mounting holes on the previous part Y (NOT THE CUTOUT SECTION). Use a laser level or box level to ensure that the horizontal template is level on the wall.
Once level on the wall mark the 3rd gable (part E) position on the wall using a pencil. Be sure to mark the center of the hole where the screw/anchor will be inserted.
Continue the process of securing the horizontal template and marking the gable locations on the wall with pencil until all gable locations are marked.
l'acrage.
3
Y 4
Y
5
X
7. For a configuration that includes a short gable (part I) you then must use another vertical template (part X) to get the proper mounting location. Take part X and fold up the bottom sufficiently so that it does not touch the baseboard when on the wall.
Align the upper mounting holes of template X over template Y and secure with masking tape. Ensure that the mounting holes of template X are precisely over the mounting holes of template Y. Check using a laser level or box level that template X is level on the wall.
Using a pencil, mark the lower location of the gable to be installed.
7.
Utilisez un crayon de plomb pour marquer plus bas, l'emplacement du montant
Y
2
3
Y 4
Y
5
X
X
5/12
8. With all gable (part E/I) positions now marked on the wall, take each gable (part
E/I) and hold it up to where it will be installed. The upper end of each gable should sit inside the box on templates X and Y. Adjust the feet on the bottom of the gables as necessary to ensure that they are at the correct height.
For installations with a floor variance greater than 1" as measured in Chart 1, you will need to use additional shims/felt pads in order to secure your gables at the bottom.
hauteur.
le dessous de montants.
Y
2
3
Y
X
4
Y
5
X
9. Install all gable support clips (part F) onto the wall and remove templates once they are installed. Save the templates in a safe location for future use.
Conservez les gabarits pour une utilisation future.
H
F
X
H
F
6/12
10. According to your specific configuration, attach all of the shelf support brackets to the gables where indicated on your layout. Do this while the gables are detached from the wall to prevent damage to the walls or pulling out your clips.
Use the #3 Phillips head screw driver to install all the bolts (part G).
Caution: If there are shelves without a spacing of one step between them, leave one of the sides shelf support brackets off to allow you to install the lower shelf first. Once attached, you may install the above shelf support bracket.
DO NOT FORCE THE GABLES APART IN ORDER TO TRY AND FIT A SHELF.
Attention: Dans le cas de tablettes sans espaceement d'au moins un niveau entre elles,
7020-508 7020-507
J (1)
K (1)
E/I
E/I
E/I
E/I
J
K
K
7020-504
!
M (1)
M
G
E/I
J
M G
7/12
11. Once all the shelf supports are secured, you can now secure all your gables to wall - E / I.
E/I
E/I
B
E/I
G
12. Ensure that the (part E/I) installed gables are square to the wall. Do so by measuring the distance at the top against the measurement at the bottom.
Adjust the floor leveler to hold the gable in place so that the distances are the same.
nivellement, ajustez chaque montant afin que les deux mesures soient identiques.
WALL / MUR
7.25"
7.25"
8/12
13.
J
C
14.
A
K
J
9/12
15.
M
D
16.
J
B
B
B
B
J
10/12
17.
Secure shelves
Securiser etageres
18.
H
L
11/12
Some Useful Advice
You should check and re-tighten the screws and bolts a few weeks after assembly.
For cleaning, use mild soapy water only and dry with soft cloth
(other cleaning agents may cause damage not covered by the warranty).
Quelques bons conseils
Pour le nettoyage, utilisez de l'eau savonneuse douce
peuvent causer des dommage non-couverts par la garantie).
WARNING
AVERTISSEMENT
To prevent tipping and possible injury:
Do not allow anyone (including children) to climb the unit. The unit may tip over which can cause property damage, personal injury or death.
des blessures ou la mort.
DO NOT REMOVE THIS LABEL
12/12
