advertisement
Twin-tub Washing Machine
User's manual
This manual is for
HWM130-0713S
Please read this manual carefully before using.
Retain it for future reference.
0030807922A
Contents
Names of the parts - - - - - - - - - - - - - - - - - 1
Safety precautions - - - - - - - - - - - - - - - - - 2
Installation and adjustment - - - - - - - - - - - 4
Preparation before washing - - - - - - - - - - 6
The musts in washing - - - - - - - - - - - - - - - 7
Usage of the detergent - - - - - - - - - - - - - 7
Washing sequence - - - - - - - - - - - - - - - - - 8
Disposal after washing - - - - - - - - - - - - - - - 12
Trouble-Shooting *Answer to question - - - - 14
Packing list *Specification - - - - - - - - - - - - - 16
Names of the parts
Drain selector
Wash selector
Wash timer
Water-filling entrance
Inlet selector
Control panel
Filter frame
Water level adjusting lever
Lint filter
Wash tub
Valve cover
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Major frame
Spin tub
Cabinet
Pulsator
Wash tub cover
Drain hose
Base frame
Notes: All illustrations in this manual are given for reference only. Your products and
accessories may show differences from these illustrations due to our
continuous improvement.
Meaning and description of the symbols
Warning sign
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of the user.
Please check if the power receptacle has good earthing condition before using to guarantee your safety.
1
Safety precautions
Please insert the power cord into special receptacle with rated voltage. Be sure to use single-phase
three pins receptacle. The earthing
terminal of the receptacle must be
earthed reliably. If possible, please adopt electric leakage protector.
When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned or when it is idle.
If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp place like the bathroom . Never wash it with water. Do not place wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is installed on ground with carpet , do not block the ventilation hole with carpet.
Ventilation hole at the bottom of the washing machine
Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning.
Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more.
2
Safety precautions
Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children.
Do not decompose, repair or alter the machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (such as thinner, petrol etc.).
Petrol
Thinner
Handicapped or children without care shall not use the machine.
Keep the machine away from direct sunlight and heat source like the
heater.
Please put down the drain hose before washing and connect the water inlet pipe properly.
It is suggested to use foamless washing powder.
Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the washer s water inlet system and draining system will be frozen ,then result in the damaged of the whole machine. If the washer has below 0 C, please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use .
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating
the machine.
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
incomplete drainage.
2.Do not tramp or press the drain hose.
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
4.If extra drain hose is needed , please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
length shall not exceed 1.5m.
If the extra hose is too long, cut it either at point A or B.
<10cm
> 30mm
<1.5m
A B
Voltage change
This washer is assembled for 220V, but can be changed from 220V to 127V.
Check your electrical source and follow the diagram below to convert voltage.
Green
Blue
White
(1).
Loosen the fastening screw and take off the back cover.
(2). Unknit the safeguard bag to expose the connectors.
(3). Detach the white connector from the green one(220V), then inlay
it into the blue one(127V).
(4). Pack all the connectors with the safeguard bag as usual and f ix it.
Then install the back cover.
Above all the steps must be done by the special serviceman.
4
Install the lint filter
Put the underside of the lint filter into overflow filter then push the upside into overflow filter.
After installation, please refer that the lint filter installed to the right station, otherwise the lint filter may be fallen off when washing, influencing your use.
overflow filter lint filter
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation position of the drain hose. Soft item
Extend the drain hose from the side of spin tub
Back
Front
Figure 1
Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet.
Take the hose out of the fixing groove.
(See to Figure 2).
Soft item
Embed the drain hose into the groove along the side of the spin tub in the order of (1)~(3), heading
for the side of the spin tub. (See to Figure 3).
Embed the drain hose into the groove with hands. Take care not to damage the drain hose in fastening the fixing clamp.
Extend to the spin tub side
Figure 2
Embed into the groove in turn
Figure 3
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
Water inlet hose entrance on the control pane directly.(pull it out to dismantle it)
Water inlet
Select water level according to the quantity of the laundries.
Set the water level adjusting lever
to needed line.
Water level indicator
Maximum
Medium
Minimum
Max
Med
Min
5
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if the laundries has special requirement on washing
Clear the pocket. Take out the coins, sand, hairpins etc.
Tie the long strips; fasten the buttons; close zippers.
The quantity of When the pulsator the laundries is running , the shall not be too buttons of the large. Stretch laundries may and loosen the putting them in cause noise. For laundries before the sake of discretion, please the tub.
put the laundries with buttons into other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
6
The musts in washing
The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can
be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put in reasonable amount of laundries and the laundries can be turned round in washing for one time washing.
Do not select " Maximum " water level for
laundries less than 1.0kg, so as to avoid splashing of water.
Usage of the detergent
How to use the washing powder
How to use the whitener
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or pattern as they
are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the laundries than the detergent. Therefore please use it with proper quantity.
Dosage of different washing powder is different. Please refer to the instruction of the washing powder for the detail dosage.
7
Washing sequence
Inlet selector
Wash timer
(To set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer).
Wash selector
(Standard current,
strong current)
(Do not set drain selector on Drain position during washing)
(To set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
3 15
WASH SPIN
12
9
WASH TIMER
6
WASH SELECTOR
Wash
1 Inlet selector
(1) Set fill selection to Wash side .
( Figure 1 )
(2 ) Adjust water level rod to a position as needed.
WASH SPIN
Figure 1
2 Fill water and add solved powder detergent until water reaches a suitable level.
( Figure 2 )
It begin to wash to dispense detergent uniformly.
3 Put in the wash load, and supplement water as necessary.
STRONG
STANDARD
Figure 2
4 Select the current
Select the strength of the current according to the laundries. (Figure 3)
WASH SELECTOR
Figure 3
OFF
15 3
5 Select the washing time
Select the washing time according to the laundries. (Figure 4)
6 After washing,set the DRAIN SELECTOR
at DRAIN .(Figure 5)
12
WASH TIMER
OFF
9
6
Figure 4
DRAIN
Figure 5
DRAIN SELECTOR
8
Midway spinning
1.
Put the laundries into the spin tub evenly and smoothly.
2.
Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push Gland
Push
Proper The laundries are slanting
Proper No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.
Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
WASH SPIN
9
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is a few , please use "Standard" current.
If you use "Strong" current, it may splash.
10
Spinning
1. Put the laundries into the spin tub
evenly and smoothly.
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and draining
or rinsing with water-filling
together, please first do spinning for around 1 minute,
then do draining or rinsing
with water-filling. Otherwise
the spinning will stop owing to too much water stored in the spin tub.
11
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Press the elastic piece at upper end of lint filter to release the tab from the filter cover , and pull the lint
filter outward to remove it. (See Figure 1).
Figure 1
2. Remove lint
Pull the lower end of lint filter rear cover outward
to disassemble it from the lint filter front cover.
Remove lint completely with clear water. (See
Figure 2).
Lint filter rear cover
Disassemble
3. Install lint filter
Page 4
Assemble
Lint filter front cover
Figure 2
Cleaning the overflow filter
Too much lint on the overflow filter will influence the normal usage of the machine. Please clean it every two months.
1 Take off the overflow filter.
Elastic fixing claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
12
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
(3).Hang up the hook at
upper side.
(4).Push the upper part in as
indicated in Figure 2.
Hook
Water level adjusting lever
Corrugation pipe
Figure 1
Figure 2
Disposal of the complete unit
Wipe the complete unit with soft cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Alcohol
Petrol Thinner
After washing, dismount the water inlet hose.
Do not store water in the tub for long period. Discharge the water immediately after each using.
Pull off the power plug and hang up the power cord.
Hang up the drain hose.
Wipe off the water drops on the surface and inside the tub with clean soft cloth.
Open the cover of the wash tub and the inner/outer cover of the spin tub for some time (about one hour), then close them.
13
Trouble-shooting Answer to question
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub, please take them out immediately.
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "DRAIN SELECTOR" at "OFF" . If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
Below 50 c
2~3L
When the water is frozen
Pour hot water below 50 into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
14
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomena The reason
The machine does
not act.
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The draining does not work
Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
There's abnormal sound during washing
Are there hair pin, coins or metal items brought
inside the tub?
There's abnormal sound and violent
vibration during spinning
Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to the outer side of the spin tub?
Are the laundries in spin tub too much?
There may be some water flowing out of the drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
15
Packing list
Name
User's manual
Water inlet hose
Gland
Twin-tub washing machine
Quantity
One piece
One piece
One piece
One set
Specification
Water level / Water quantity (about)(L) Maximum/89L Medium/75L Minimum/63L
Rated washing capacity kg
Rated spinning capacity kg
Injection pressure(MPa)
Rated washing power(W)
10.0
6.0
0.02~0.2
270/340
Rated spinning power(W) 125/180
Made in China
16
advertisement
Related manuals
advertisement