advertisement
Washing sequence
Inlet selector
Wash timer
(To set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer).
Wash selector
(Standard current,
strong current)
(Do not set drain selector on Drain position during washing)
(To set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
3 15
WASH SPIN
12
9
WASH TIMER
6
WASH SELECTOR
Wash
1 Inlet selector
(1) Set fill selection to Wash side .
( Figure 1 )
(2 ) Adjust water level rod to a position as needed.
WASH SPIN
Figure 1
2 Fill water and add solved powder detergent until water reaches a suitable level.
( Figure 2 )
It begin to wash to dispense detergent uniformly.
3 Put in the wash load, and supplement water as necessary.
STRONG
STANDARD
Figure 2
4 Select the current
Select the strength of the current according to the laundries. (Figure 3)
WASH SELECTOR
Figure 3
OFF
15 3
5 Select the washing time
Select the washing time according to the laundries. (Figure 4)
6 After washing,set the DRAIN SELECTOR
at DRAIN .(Figure 5)
12
WASH TIMER
OFF
9
6
Figure 4
DRAIN
Figure 5
DRAIN SELECTOR
8
Midway spinning
1.
Put the laundries into the spin tub evenly and smoothly.
2.
Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push Gland
Push
Proper The laundries are slanting
Proper No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.
Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
WASH SPIN
9
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is a few , please use "Standard" current.
If you use "Strong" current, it may splash.
10
Spinning
1. Put the laundries into the spin tub
evenly and smoothly.
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and draining
or rinsing with water-filling
together, please first do spinning for around 1 minute,
then do draining or rinsing
with water-filling. Otherwise
the spinning will stop owing to too much water stored in the spin tub.
11
advertisement
Related manuals
advertisement