INSTALLATION AND SAFETY INSTRUCTIONS

ASSEMBLY FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU

ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED

OR THE CIRCUIT BREAKER OFF .

GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this fixture.

STEP 1:

Carefully remove the fixture from the carton and check that all parts are included, as shown in Figures 1 & 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY, MOUNT TO OUTLET BOX OR SUPPORTING

SYSTEM ABLE TO SUPPORT THE WEIGHT OF THE FIXTURE.

*NOT SUPPLIED (FIG. 1)

RETAINING

RING (P)

GLASS (G)

FIXTURE RING (S)

FRONT PLATE (M)

CAP NUTS (T)

FRONT PLATE

(DECORATIVE FRONT)

*WIRE

CONNECTOR

BACK PLATE

FIGURE 2

*NOT SUPPLIED

Safety Instruction

HC-846

082704

Line art shown may not exactly match the fixture enclosed.

However, the installation instructions do apply to this fixture.

Fill In Item Number On Carton And

File This Sheet For Fixture Reference. ITEM#_________

INSTALLATION HC-846

IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET

BOX.

STEP 1:

Punch out appropriate holes in backplate [A], if applicable, to correspond with holes in outlet box.

STEP 2:

Push socket wires thru plastic bushing (If applicable).

STEP 3:

A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

GROUP A: CONNECT TO BLACK

HOUSE WIRE

BLACK

GROUP B: CONNECT TO WHITE

HOUSE WIRE

WHITE

*

PARALLEL WIRE (ROUND & SMOOTH) *

PARALLEL WIRE (SQUARE & RIDGED)

* NOTE: When parallel wire is used, the tracer wire is square shaped or ridged, and the less tracer wire is round in shape or smooth. (Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart.

B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do Not twist wires together before using wire connectors.

C. Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.

D. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps B and C, as above, and check again for a firm connection.

E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner.

STEP 4:

GROUNDING INSTRUCTIONS: The green grounding screw (L) is to be inserted into the hole with two raised dimples provided on the universal mounting bar. Wrap the ground wire from the fixture (if supplied) and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (L) on the universal mounting bar. If uninsulated ground wire is on the universal mounting bar, connect the ground wire from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied) (See Figure

2).

NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to have ground wires. These fixtures still meet all U.L. specifications. The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

FINAL ASSEMBLY

Make sure no bare wires can be seen outside wire connectors.

STEP 1:

Tuck wires into outlet box. Attach backplate to outlet box by placing outlet box screws (not supplied) through punched-out holes in backplate. (Optional- Wood screws placed in outer holes will provide additional support).

STEP 2:

Place front plate (M) over mounting screws on back plate and secure with cap nuts (T).

STEP 3:

Place glass (G) through fixture ring (S) onto socket assembly and secure in place with retaining ring (P).

STEP 4:

Install lamps.

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.

Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.