Zenith Installation Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: ZENITH
Included Communications Adapter(s):
Quantity Part Number
1 26-471-01
Description
ADP, UNV, “C”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “ ✔ ” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
ZENITH PRO
Config as
Model
✔ Zenith Pro
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 0 E J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-471-01
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-419-01 Rev. A
Zenith Installation Configuration and Connections
Zenith Pro Projector Configuration
Verify that the System 8/10 P
LUS
is already configured for the Zenith Pro projector. The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config as
Model
✔ Zenith Pro
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 0 E J2
↓ ↓ ↑ ↓ ↑
-
↓ ↓ ↓ ↑ ↓
26-471-01
ON
1 2 3 4 5 6 7 8 9 10
_ RS5 is for RGB switching delay. See page 3-4 for more information on switch functions.
RS2
SW15 DIP Switch
RS3
RS5 RS2 RS1
RS1 RS4
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “Zenith Pro”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the next page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “Remote
1” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the
Zenith Pro projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 P
LUS
and projector to normal operation.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-419-01 Rev. A Page 1
Zenith Installation Configuration and Connections
Zenith Pro Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to a Zenith Pro projector. Refer to Zenith documentation to continue the installation.
In
Video
Out Y
Y/C IN
C
S-Video
In
Remote 1 System Bus
In Out
Remote 2
R G/G Sync B H/Sync
RGB 1 IN
V R/Pr G/Y B/Pb H/Sync
RGB 2 IN
V
"C"
25-Pin
26-471-01
"C"
15-Pin HD
CC 50'
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-419-01 Rev. A Page 2
