ASK Installation Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: ASK
Included Communications Adapter(s):
Quantity
1
1
Part Number
26-467-01
26-523-01
Description
ADP, UNV, “A”
ADP, UNV, “N”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “ ✔ ” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
ASK A10+
Config as
Model
✔ ASK A10+
ASK A9
ASK C100
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 E 9 J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓
26-467-01
1 0 E 9 J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓
26-467-01
0 0 E F J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓
26-523-01
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 1
ASK Installation Configuration and Connections
ASK A10+ Projector Configuration
Config as
Verify that the System 8/10 P
LUS
is already configured for the ASK A10+ projector. The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Model
✔ ASK A10+
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 E 9 J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓
¯
↑ ↓
26-467-01
ON
1 2 3 4 5 6 7 8 9 10
_RS5 is for RGB switching delay. See page 3-4 for more information on switch functions.
RS2
SW15 DIP Switch
RS3
RS5 RS2 RS1
RS1 RS4
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “ASK A10+”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. Connect the ASK adapter’s 26-pin male connector to the projector’s “Source 1“ port. Next, connect the Comm Adapter’s 9-pin female connector to the projector’s
“RS-232” port.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm
Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the
System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the ASK adapter’s 15-pin male “Computer” connector. For composite video, connect the
RCA connector from the System 8/10 Plus to the composite video “C” connector of the ASK adapter. For S-video, connect the DIN connector from the System 8/
10 Plus to the S-video “S” connector of the ASK adapter.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 2
ASK Installation Configuration and Connections
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 P
LUS
and projector to normal operation.
ASK A10+ Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to the ASK
A10+ projector. Refer to ASK documentation to continue the installation.
15-Pin Male
15-Pin Female
26-Pin Male
ASK Adapter
R L C S
9-Pin Female
Comm Adapter
26-467-01
A
9-Pin Male
15-Pin Female (monitor)
9-Pin Female
Composite Video
RGBHV 5 BNC
15-Pin Male S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 3
ASK Installation Configuration and Connections
ASK A9 Projector Configuration
Config as
Verify that the System 8/10 P
LUS
is already configured for the ASK A9 projector.
The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Model
ASK A9
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
1 0 E 9 J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓
¯
↑ ↓
26-467-01
_RS5 is for RGB switching delay. See page 3-4 for more information on switch functions.
RS2
ON 1 2 3 4 5 6 7 8 9 10
SW15 DIP Switch
RS3
RS5 RS2 RS1
RS1 RS4
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “ASK A9”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. Connect the ASK adapter’s 26-pin male connector to the projector’s “Source 1” port. Next, connect the Comm Adapter’s 9-pin female connector to the projector’s
“RS-232” port.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm
Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the
System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the ASK adapter’s 15-pin male “Computer” connector. For composite video, connect the
RCA connector from the System 8/10 Plus to the composite video “C” connector of the ASK adapter. For S-video, connect the DIN connector from the System 8/
10 Plus to the S-video “S” connector of the ASK adapter.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 4
ASK Installation Configuration and Connections
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 P
LUS
and projector to normal operation.
ASK A9 Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to the ASK A9 projector. Refer to ASK documentation to continue the installation.
15-Pin Male
15-Pin Female
26-Pin Male
ASK Adapter
R L C S
9-Pin Female
Comm Adapter
26-467-01
A
9-Pin Male
15-Pin Female (monitor)
9-Pin Female
Composite Video
RGBHV 5 BNC
15-Pin Male S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 5
ASK Installation Configuration and Connections
ASK C100 Projector Configuration
Config as
Verify that the System 8/10 P
LUS
is already configured for the ASK C100 projector. The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Model
ASK C100
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 E F J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓
¯
↑ ↓
26-523-01
ON 1 2 3 4 5 6 7 8 9 10
_RS5 is for RGB switching delay. See page 3-4 for more information on switch functions.
RS2
SW15 DIP Switch
RS3
RS5 RS2 RS1
RS1 RS4
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “ASK C100”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. Connect the Comm adapter’s DIN connector to the projector’s “Mouse 1” port.
6. Connect the CC-50' (or CC-100') communications extension cable from the 9-pin male connector of the Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the projector’s 15-pin female “Analog Computer VGA” connector. For composite video, connect the RCA connector from the System 8/10 Plus to the projector’s
“Video” connector. For S-Video, connect the DIN connector from the System 8/
10 Plus to the projector’s “S-Video” connector.
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 6
ASK Installation Configuration and Connections
9. Return System 8/10 P
LUS
and projector to normal operation.
ASK C100 Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to the ASK
C100 projector. Refer to ASK documentation to continue the installation.
REMOTE
CONTROL
MOUSE 2 MOUSE 1
○
○
S-VIDEO
○
○
AUDIO
IN
VIDEO
○
AUDIO
OUT
AUDIO
(1) (2)
IN (3)
○
○
○
○
○
○
○
○
○
○
8-pin male DIN
○
○
○
○
○
Comm Adapter
26-523-01 "N"
N
○
○
○
9-Pin Male
○
○
9-Pin Female
DIGITAL COMPUTER
DVI (1)
○
○
○
○
○
○
ANALOG COMPUTER
VGA (2)
ANALOG COMPUTER
VGA (3)
MONITOR
RGBHV
15-Pin Male
Composite
Video
S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-548-01 Rev. B Page 7
