Electrohome Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: ELECTROHOME
Included Communications Adapter(s):
Quantity Part Number
1
1
1
26-474-01
26-467-01
26-477-01
Description
ADP, UNV, “F”
ADP, UNV, “A”
ADP, UNV, “H”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS INDI-
CATED BY THE “ ✔ ” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL DIF-
FERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
ELECTROHOME MARQUEE/
VISTA/HAL
Config as
✔
✔
✔
Model
Electrohome Marquee
Electrohome Vista
Electrohome Hal
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0
0
0
0
0
0
5
5
5
6 J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-474-01
6 J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-467-01
6 J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-467-01
Electrohome EPS 0 0 F E J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-477-01
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-400-01 Rev. B
Electrohome Configuration and Connections
Electrohome Marquee/Vista/Hal Projector Configuration
Check to see if the System 8/10 P
LUS
is already configured for the Marquee/
VistaPro/Hal projector. The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config as
Model
✔ Electro. Marquee
✔ Electro. Vista
✔ Electro. Hal
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 5 6
0 0 5 6
0 0 5 6
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-474-01
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-467-01
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↑ ↑ ↓
26-467-01
ON 1 2 3 4 5 6 7 8 9 10
_ When connecting the projector for Video Loopback
(VLB) operation SW15, DIP switch #8 must be Down.
See page 3-4 for switch description, and page 2-10 for VLB operation.
RS2
RS5 RS2 RS1
SW15 DIP Switch
RS3
RS1 RS4
RS5 is for RGB switching delay. See page 3-4 for more information on switch functions.
RS3 RS4
Configured For:
RS-232
3.
Use a grease pencil (or other rub-off marker) to mark the space on the label next to “Marquee” or “VistaPro” or “Hal”.
4.
Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a host/peripheral system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the following page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female
“Switcher” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the
Marquee/VistaPro projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 P
LUS
and projector to normal operation.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-400-01 Rev. B Page 1
Electrohome Configuration and Connections
Electrohome Marquee Series Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to a Marquee projector. Refer to Electrohome Marquee documentation to continue the installation.
_ If the installation includes looping
( host/peripheral ) switchers, see
Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
In
RS-232
Out
To
Switcher
Electrohome Marquee Projector
Sync
Red Green Blue Hor/Comp Vert
Channel List
9-Pin
The Marquee/VistaPro projector software allows the user to program the projector slot and input numbers to match the System 8/10 P
LUS
input numbers.
Turn the projector on and use the
Marquee/VistaPro remote to display the channel list shown in the picture to the right.
Use the arrow keys to edit the list. Press Exit when finished.
"F" 26-474-01
"F"
CC 50'
15-Pin HD
3, 4 or 5 BNC
Electrohome Vista/Hal Series Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to a VistaPro projector. Refer to Electrohome Vista/Hal documentation to continue the installation.
VID 1
COMP. VIDEO
VID 2
S-VIDEO
AUDIO
L
IN
VID-1
IN
VID-2
R
RED GREEN BLUE
SYNC
H/C SYNC V SYNC
DAT 1
AUDIO
L
IN OUT
DAT 1
R
RS-232
STATUS
REMOTE
POWER
NETWORK IN
NETWORK OUT
SPARE
SWITCHER
9-Pin HD
26-467-01
"A"
"A"
9-Pin HD
CC 50'
15-Pin HD
S-VIDEO (Y)
COMP VIDEO
S-VIDEO (C)
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-400-01 Rev. B Page 2
Electrohome Configuration and Connections
Electrohome EPS Projector Configuration
Check to see if the System 8/10 P
LUS
is already configured for the Marquee/
VistaPro/Hal projector. The general setup is explained on page 3-4 and the switch settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 P
LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P
LUS to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config as
Model
Electrohome EPS
Rotary Switches Cable SW15 Settings Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0 0 F E J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-477-01
ON 1 2 3 4 5 6 7 8 9 10
SW15 DIP Switch
RS2 RS3
RS5 RS2 RS1
RS1 RS4
RS3 RS4
Configured For:
RS-232
3.
Use a grease pencil (or other rub-off marker) to mark the space on the label next to “EPS”.
4.
Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a host/peripheral system, set #3 and #5 to the up position and the others down. See illustration to the left.
Use the illustration on the facing page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “RS-
232C” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 P
LUS
.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 P
LUS
outputs to the EPS projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 P
LUS
by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 P
LUS
and projector to normal operation.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-400-01 Rev. B Page 3
Electrohome Configuration and Connections
Electrohome EPS Projector Connections
Use the illustration below when connecting the System 8/10 P
LUS
to an EPS projector. Refer to Electrohome documentation to continue the installation.
RS - 232C
H
Side Panel
CommAdapter
26-477-01 "H"
9-Pin Female
Rear Panel
RGBHV 5 BNC
RCA Adapter
S-Video
Adapter
15-Pin
Male
Composite
Video
S-Video
_ If the installation includes looping ( host/peripheral ) switchers, see Chapter 5. If Video Loop
Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-400-01 Rev. B Page 4
