Extron electronics SYSTEM 8/10 Plus Configuration And Connections

Sharp Installation Configuration and Connections

SYSTEM 8/10 Plus

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: SHARP

Included Communications Adapter(s):

Quantity

1

1

Part Number

26-426-01

26-467-01

Description

ADP, SHARP IR

ADP, UNV, “A”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “

✔

” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR:

SHARP XG (RS-232)

Config as

Model

✔ XG (RS-232)

XG-E1200U

XG-1000/E1100

XG-NV6/NV2U/NV5

XG-NV3

XG-P10XU

PG-C30XU

XG-P20XU

Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

0 0 F 9 J2

↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

1 0 F 3 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-426-01

0 0 F 3 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-426-01

2 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

1 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

2 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

2 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

1 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓

26-467-01

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 1

Sharp Installation Configuration and Connections

Sharp XG Series Projector Configuration (RS-232)

Verify that the System 8/10 Plus is already configured for the Sharp XG Series projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.

1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.

_________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF.

2. Set the System 8/10 Plus switches as follows:

Config as

4

Model Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Sharp XG (RS-232) 0 0 F 9 J2

↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓

¯

↑ ↓

26-467-01

ON 1 2 3 4 5 6 7 8 9 10

SW15 DIP Switch

RS2

RS3

RS5 RS2 RS1

RS1

RS3 RS4 RS4

Configured For:

RS-232

3. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left.

4. Use the illustration on the following page and continue with the steps below.

5. Connect the BNC cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite

Video).

________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual.

________ Some Sharp projectors will only select S-Video when connected to an S-Video source. You should not input S-Video and Composite Video sources simultaneously on these models. Consult your Sharp manual to determine if your model supports CVID and SVID simultaneously.

6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

7. Installation is now completed.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 2

Sharp Installation Configuration and Connections

System 8/10 Plus to Sharp XG Series Projector Connections (RS-232)

Use the illustration below as a guide when connecting the System 8/10 Plus to a

Sharp projector. Refer to Sharp documentation to continue the installation.

________ Important note! For Sharp projectors which do not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time. For those Sharp projectors which will allow you to connect to S-Video and Composite Video sources simultaneously - please refer to the inset diagram below.

Composite

Video or

S-Video

Universal

CommAdapter

26-467-01

9-Pin Male

9-Pin Female

IN

1

VIDEO INPUT

S-VIDEO VIDEO

IN

2

Composite

Video and

S-Video

VIDEO INPUT

S-VIDEO VIDEO

AUDIO INPUT

L R

DO NOT

CONNECT

HERE

CONNECT

HERE

VIDEO OUTPUT

INPUT 1

FILTER

ON

R

OFF

PC CONTROL

COMPUTER RGB

G

MOUSE FOR PC98 WIRED

REMOTE

OUTPUT

AUDIO OUTPUT

L R

COMPUTER

AUDIO IN

B

INPUT 2

H V

DC5V OUTPUT

MAX CURRENT 1A

-

+

RGBHV 5 BNC 15-Pin

Male

Composite

Video or

S-Video

________ When RS-232 control of the projector is used, the projector’s IR remote can be used. However, because the projector’s IR remote does not communicate with the System 8/10 Plus switcher, the projector and switcher can become out-ofsync if the projector’s IR remote is used to change the projector’s input, picture mute or power settings. Should this occur, press the power, mute or channel buttons on the switcher to allow the projector and switcher to resynchronize.

________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the

System 8/10 Plus User’s Manual.

________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 3

Sharp Installation Configuration and Connections

Sharp XG-1000/E1100 Projector Configuration

Config as

4

Verify that the System 8/10 P

LUS

is already configured for the Sharp projector.

The general setup is explained on page 3-4 and the switch settings for the Sharp projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 P

LUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 P

LUS to verify that the main power is OFF; also turn the projector power OFF.

Model

Sharp XG

2. Set the switches as follows:

Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

0 0 F 3 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓

ON

1 2 3 4 5 6 7 8 9 10

¯

↑ ↓

26-426-01

SW15 DIP Switch

RS2

RS3

RS5 RS2 RS1 _ RS5 is for

RGB switching delay. See page 3-4 for more information.

RS1

RS3 RS4 RS4

Configured For:

RS-232

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “Sharp XG”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See picture to the left.

Use the illustration on the next page to do the following steps.

5. Connect the Comm Adapter’s miniphone connector to the “Wired Remote” input jack and the power plug to the Aux power port on the rear panel of the projector.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the

Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 P

LUS

. (If you wish to make your own communications cable, see page 3-2.)

______ Secure the screws on all D connectors.

7. Connect the BNC cables from the System 8/10 P

LUS

outputs to the Sharp projector inputs according to the application requirements.

8. Apply Main Power to the System 8/10 P

LUS

by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

9. Return System 8/10 P

LUS

and projector to normal operation.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 4

Sharp Installation Configuration and Connections

Sharp XG-1000/E1100 Projector Connections

Use the illustration below when connecting the System 8/10 P

LUS

to a Sharp XG-

1000/E1100 projector. Refer to Sharp documentation to continue the installation.

ON

Filter

OFF

ANALOG DIGITAL

COMPUTER RGB INPUT

COMPUTER RGB OUTPUT

15-Pin

Sharp XG-1000 or E1100 Projector

INPUT

1

AUDIO

R L

VIDEO S-VIDEO

WIRED

REMOTE

INPUT

2

OUTPUT

C-SYNC

OUTPUT

MAX CURRENT

2 0 0 m A

RGB INPUT

R G B

+ red cable

AUDIO 15.75kHz/15.625kHz

ANALOG RGB

Sharp COM

Adapter

26-426-01

9-Pin

15-Pin

CC 50'

________ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 5

Sharp Installation Configuration and Connections

Sharp XG-E1200U LCD Projector Configuration

Verify that the System 8/10 Plus is already configured for the Sharp XG-E1200U projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.

1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.

___________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF.

2. Set the System 8/10 Plus switches as follows:

Config as

4

Model Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Sharp XG-E1200U 0 0 F 3 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓

ON 1 2 3 4 5 6 7 8 9 10

¯

↑ ↓

26-426-01

SW15 DIP Switch

RS2

RS3

RS5 RS2 RS1

RS1

RS3 RS4 RS4

Configured For:

RS-232

3. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left.

4. Use the illustration on the following page and continue with the steps below.

5. Connect the BNC cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite

Video).

________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual.

________ Because the projector’s video port will only select S-Video when connected to an

S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored.

6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

7. Installation is now completed.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 6

Sharp Installation Configuration and Connections

System 8/10 Plus - Sharp XG-E1200U LCD Projector Cable Diagram

Use the illustration below as a guide when connecting the System 8/10 Plus to a

Sharp XG-E1200U projector. Refer to Sharp documentation to continue the installation.

➶

(26-353-01, male-to-male)

VIDEO INPUT

S-VIDEO VIDEO

AUDIO INPUT

L R

VIDEO OUTPUT

PC CONTROL

MOUSE FOR PC98 WIRED

REMOTE

➶

See first note below

INPUT 1

COMPUTER RGB

OUTPUT

L

AUDIO OUTPUT

R

COMPUTER

A U D I O I N

FILTER

ON

OFF

R G B

INPUT 2

H V

DC5V OUTPUT

MAX CURRENT 1A

-

+

Power Plug

➶

Adapter (26-446-01)

SHARP COM

ADAPTER 26-426-01

VIDEO INPUT

S-VIDEO VIDEO

➶

To Composite Video source (see last note on previous page)

________ When the Wired Remote jack is installed, the projector’s IR Receivers are disabled. This jack can be installed or removed at any time. Please perform the basic projector setup before installing the Wired Remote jack.

________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the

System 8/10 Plus User’s Manual.

________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.

Configuring the Projector

Please refer to your Sharp XG-E1200U Operations Manual to set up your projector. Also, in order for the System 8/10 Plus to know whether the projector is “ON” or “OFF”, the projector’s 5VDC output jack must be set to “LAMP”.

1. Select MENU.

2. Select SYSTEM SETUP.

3. Select DC 5V OUTPUT.

4. Using the buttons on the rear of the Sharp XG-E1200U, select

LAMP.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 7

Sharp Installation Configuration and Connections

Sharp NV6 Projector Configuration

Config as

4

Verify that the System 8/10 Plus is already configured for the Sharp NV6 projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.

1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.

__________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF.

2. Set the System 8/10 Plus switches as follows:

Model

Sharp NV6

Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

2 0 F 9

↑ ↓

26-467-01

ON

J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓

¯

1 2 3 4 5 6 7 8 9 10

SW15 DIP Switch

RS2

RS3

RS5 RS2 RS1

RS1

RS3 RS4 RS4

Configured For:

RS-232

3. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left.

4. Use the illustration on the following page and continue with the steps below.

5. Connect the video cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite

Video).

________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual.

________ Because the projector’s video port will only select S-Video when connected to an

S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored.

6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

7. Installation is now completed.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 8

Sharp Installation Configuration and Connections

System 8/10 Plus - Sharp NV6 Projector Connections

Use the illustration below as a guide when connecting the System 8/10 Plus to a

Sharp NV6 projector. Refer to Sharp documentation to continue the installation.

________ Important note! When connecting the Switcher’s BNC output to either the projector’s BNC or 15-pin input (but not both simultaneously), set the projector’s

input type selector switch to the appropriate “BNC” or “15-pin” setting.

________ The Sharp NV6 projector does not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time.

input type selector switch

Sharp RS-232C cable

Universal

CommAdapter

26-467-01

○

○

○

○

○

○

○

Sharp NV6 Connect.eps

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

9-Pin Female

9-Pin Male

CC cable

RGBHV 5 BNC

Important note!

Composite Video and S-video output to the projector may not be connected simultaneously

15-Pin

Male

Composite

Video or

S-Video

________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the

System 8/10 Plus User’s Manual.

________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 9

Sharp Installation Configuration and Connections

Sharp NV3 Projector Configuration

Config as

4

Verify that the System 8/10 Plus is already configured for the Sharp NV3 projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.

1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual.

__________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF.

2. Set the System 8/10 Plus switches as follows:

Model

Sharp NV3

Rotary Switches Cable SW15 Settings Comm

RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

1 0 F 9 J2

↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓

ON 1 2 3 4 5 6 7 8 9 10

¯

↑ ↓

26-467-01

SW15 DIP Switch

RS2

RS3

RS5 RS2 RS1

RS1

RS3 RS4 RS4

Configured For:

RS-232

3. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left.

4. Use the illustration on the following page and continue with the steps below.

5. Connect the video cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite

Video). One end of the Universal Comm adapter plugs into the IOIOI port of the

Sharp PC Control adapter. The Sharp PC Control adapter plugs into the projector’s PC Control port 1.

________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual.

________ Because the projector’s video port will only select S-Video when connected to an

S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored.

6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

7. Installation is now completed.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 10

Sharp Installation Configuration and Connections

System 8/10 Plus - Sharp NV3 Projector Connections

Use the illustration below as a guide when connecting the System 8/10 Plus to a

Sharp NV3 projector. Refer to Sharp documentation to continue the installation.

________ The Sharp NV3 projector does not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○

PC Control port 1

Universal

CommAdapter

26-467-01

Sharp PC Control adapter

9-Pin Female

9-Pin Male

CC cable

RGBHV 5 BNC

15-Pin

Male

See note above

Composite

Video or

S-Video

________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the

System 8/10 Plus User’s Manual.

________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C Page 11