Lucent Technologies PSAX 23N34 E1 IMA Module, PSAX 1000, 1250, 2300, 4500 Multiservice Media Gateway User Guide

PDF
Dokument
PacketStar&reg; PSAX
21-Port High-Density E1 IMA Module
User Guide
Model 23N34
for the PacketStar&reg; PSAX Multiservice Media Gateways
Issue 1, December 2004
System Software Release 10.0.0
Doc. No.: 255-700-584
Copyright &copy; 2004 by Lucent Technologies. All rights reserved.
For trademark, regulatory compliance, and related legal information,
see the &quot;Legal Notices, Safety, and Regulatory Information&quot; section.
Legal Notices, Safety, and Regulatory
Information
Copyright
Copyright &copy; 2004 by Lucent Technologies. All rights reserved.
This material is protected by the copyright laws of the United States and
other countries. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to Lucent Technologies), except
in accordance with applicable agreements, contracts or licensing, without the
express written consent of the originating organization and the business
management owner of the material.
Trademarks
PacketStar , Lucent, Lucent Technologies, and the Lucent Technologies logo
are registered trademarks of Lucent Technologies in the USA. Other product
and brand names mentioned in this guide are trademarks or registered trademarks of their respective owners.
Notices
The information in this document is for informational use only, is subject to
change without notice, and should not be construed as a commitment by
Lucent Technologies, Inc. This document is without warranty of any kind,
either expressed or implied. Lucent Technologies, Inc. assumes no responsibility for any errors, inaccuracies, or omissions. Neither is any liability
assumed for damages resulting from the use of the information or instructions contained herein. Lucent Technologies, Inc. is not responsible for any
damage or loss to your data or equipment resulting either directly or indirectly from use of this document.
Warranty Information
Software and Hardware Limited Warranties
Lucent Technologies provides a 90-day limited software warranty, and a oneyear limited hardware warranty on this product. Refer to the Software License
and Limited Warranty Agreement and the Lucent Technologies InterNetworking Systems Global Warranty that accompanied your package for more information.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
iii
Warranty Warnings
! WARNING:
When inserting modules into the chassis, slide them gently, not forcefully. Excessive force may cause the modules to be seated improperly in
the chassis, and result in possible damage to the module or the chassis.
Install or remove modules one at a time. Doing this aids in preventing
the PSAX system from indicating any erroneous failure messages, and
allows the PSAX system time to reinitialize and display the accurate configuration of the module that is inserted.
! CAUTION:
Modifying or tampering with PSAX chassis components may void your
warranty. Any modification to this equipment not expressly authorized
by Lucent Technologies may void your granted authority to operate such
equipment.
! CAUTION:
Shipping the chassis with removable I/O, server, or CPU modules
installed may cause damage to the chassis and the modules. Damage to
any of the components in the system resulting from shipping the chassis
with removable modules installed will void your warranty.
Safety Warnings and Information
When installing and operating the 21-Port High-Density E1 IMA module, follow the safety guidelines provided in the PacketStar&reg;PSAX Multiservice Media
Gateway Safety Guidelines, which accompanies this product, to help prevent
serious personal injury and damage to the module. Please read all warnings
and instructions supplied before beginning installation or configuration of
this module. In addition to the general safety information provided, you
should also refer to the appropriate PSAX installation guide for other important safety information and procedures.
Regulatory Standards Compliance
Safety and Electromagnetic Compatibility (EMC)
The following PacketStar PSAX systems are compliant with applicable safety
and EMC standards when configured with the 21-Port High-Density E1 IMA
module (model 23N34):
• PSAX 1000 system
• PSAX 1250 system
• PSAX 2300 system
• PSAX 4500 system
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
iv
Release 10.0.0
255-700-584
Refer to the PacketStar PSAX 1000, PSAX 1250, PSAX 2300, or PSAX 4500
installation guide for details on safety and EMC standards compliance.
Telecommunications
The 21-Port High-Density E1 IMA module (model 23N34) is compliant with
the following applicable telecommunications standards:
• ETSI TBR 12:1993+A1:1996 (Europe)
• ETSI TBR 13:1996 (Europe)
• TS 016:1997 (Australia)
Regulatory Statements
European Union Regulatory Statement
CE Marking
Hereby, Lucent Technologies declares that the PacketStar PSAX 1000
(-48 V dc and 220 V ac), PSAX 1250 (-48 V dc and 220 V ac), PSAX 2300,
and PSAX 4500 Multiservice Media Gateways, including the equipment documented in this publication, are in compliance with the essential requirements and other relevant provisions of the following Council Directives:
• Low Voltage 72/23/EEC
• Electromagnetic Compatibility (EMC) 89/336/EEC
• Radio Equipment and Telecommunications Terminal Equipment
1999/5/EC
The Lucent PacketStar PSAX Multiservice Media Gateways deployed in the
European Economic Area (EEA) are intended for connection to E1, E3,
STM-1, and STM-4c networks. The EC Declarations of Conformity may be
viewed or printed at the following public-access Internet site:
http://www.lucentdocs.com/ins
EU-regulativer
CE-m&aelig;rkning
Lucent Technologies erkl&aelig;rer hermed at PacketStar PSAX 1000 (-48 V dc og
220 v vekselstr&oslash;m), PSAX 1250 (-48 V dc og 220 v vekselstr&oslash;m), PSAX 2300,
og PSAX 4500 Multiservice Media Gateways, inkl. det udstyr der findes
behandlet i denne dokumentation, er i overensstemmelse med f&oslash;lgende EUdirektiver:
• Lavsp&aelig;ndingsdirektivet 72/23/EEC
• EMC-direktivet 89/336/EEC
• Direktivet om radio og teleterminaludstyr 1999/5/EC
Lucent PacketStar PSAX Multiservice Media Gateways, anvendt i E&Oslash;S
(Europ&aelig;iske &Oslash;konomiske Samarbejde) skal forbindes med E1, E3, STM-1 og
STM-4c netv&aelig;rk. EU-overensstemmelseserkl&aelig;ringen er at finde p&aring; f&oslash;lgende
internetside hvorfra den ogs&aring; kan udskrives:
http://www.lucentdocs.com/ins
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
v
Beh&ouml;rdliche Standard-CE-Kennzeichnung f&uuml;r die Europ&auml;ische Gemeinschaft
CE-Markierung
Hiermit erkl&auml;rt Lucent Technologies, dass die PacketStar PSAX 1000
(-48 V DC und 220 V~), PSAX 1250 (-48 V DC und 220 V~), PSAX 2300, und
PSAX 4500 Multiservice Media Gateways, einschlie&szlig;lich den in dieser Publikation dokumentierten Anlagen, die notwendigen Anforderungen und
anderen relevanten Vorschriften der folgenden Council-Direktiven einhalten:
• Niederspannungsdirektive 72/23/EEC
• Elektromagnetische Vertr&auml;glichkeit (EMC) 89/336/EEC
• Funkger&auml;te und Funkverkehr-Endeinrichtungen 1999/5/EC
Die Lucent PacketStar PSAX Multiservice Media Gateways, die in der
Europ&auml;ischen Gemeinschaft im Einsatz stehen, dienen zum Anschluss an folgende Netztypen: E1, E3, STM-1 und STM-4c. Die Konformit&auml;tserkl&auml;rung f&uuml;r
die Europ&auml;ische Gemeinschaft kann auf folgendem, &ouml;ffentlich zug&auml;nglichem
Internet-Site eingesehen oder ausgedruckt werden:
http://www.lucentdocs.com/ins
&yen;&sup2;&sup3;&sup2;&shy;&middot;&cedil;&shy;&macr;&cent;q&para;&cent;&cedil;&frac12;&acute;&sup3;&cedil;&not;&raquo;}&frac12;&para;&ordm;&acute;&yen;&iquest;&macr; &raquo;&sup2;&ordm;&middot;&not;&raquo;
t &Auml;&yen;&sup2;&middot;&not;&amp;(
&copy;&cedil;&sup3;&acute;&yen;&para;&cent;&sup2;&not;/XFHQW7HFKQRORJLHV&uml;&not;&deg;&micro;&sup2;&copy;&shy;&cent;&cedil;&shy;&cedil;&yen;3DFNHW6WDU PSAX1000 (-48 Vdc
&macr;&yen;&shy; 9DF), PSAX1250 (-48 Vdc&macr;&yen;&shy; 9DF), PSAX2300, &macr;&yen;&shy;PSAX
Multiservice Media Gateways, &macr;&yen;&sup1;&micro;&raquo;&macr;&yen;&shy;&sup3;&copy;&reg;&sup3;&acute;&deg;&shy;&middot;&plusmn;&cent;&raquo;&plusmn;&copy;&cedil;&yen;&sup2;&cedil;&frac12;&acute;&yen;&cedil;&not;&raquo;&acute;&yen;&para;&sup3;&curren;&middot;&yen;&raquo;
&macr;&uml;&sup3;&middot;&not;&raquo;&copy;&sup2;&yen;&para;&plusmn;&sup3;&sup2;&iexcl;&frac34;&sup3;&sup2;&cedil;&yen;&shy;&plusmn;&copy;&cedil;&shy;&raquo;&brvbar;&yen;&middot;&shy;&macr;&raquo;&yen;&acute;&yen;&shy;&cedil; &middot;&copy;&shy;&raquo;&macr;&yen;&shy;&deg;&sup3;&shy;&acute;&raquo;&middot;&frac14;&copy;&cedil;&shy;&macr;&raquo;&uml;&shy;&yen;&cedil;&reg;&copy;&shy;&raquo;&cedil;&ordm;&sup2;
&uml;&not;&laquo;&shy;&micro;&sup2;&cedil;&sup3;&frac12;t&frac12;&plusmn;&brvbar;&sup3;&frac12;&deg;&iexcl;&sup3;&frac12;
• &yen;&plusmn;&not;&deg; &cedil;&middot;&not;(2.
• +&deg;&copy;&macr;&cedil;&para;&sup3;&plusmn;&yen;&laquo;&sup2;&not;&cedil;&shy;&macr; &middot;&frac12;&plusmn;&brvbar;&yen;&cedil;&cent;&cedil;&not;&cedil;&yen;(0&amp;(2.
• &yen;&uml;&shy;&sup3;&ordf;&ordm;&sup2;&shy;&macr;&cent;&raquo;
&copy;&reg;&sup3;&acute;&deg;&shy;&middot;&plusmn;&cent;&raquo;
&macr;&yen;&shy;
}&reg;&sup3;&acute;&deg;&shy;&middot;&plusmn;&cent;&raquo;
&cedil;&copy;&para;&plusmn;&yen;&cedil;&shy;&macr;&sup3;&curren;
&cedil;&not;&deg;&copy;&acute;&shy;&macr;&sup3;&shy;&sup2;&ordm;&sup2;&shy;&micro;&sup2;
(.
&yen;/XFHQW3DFNHW6WDU36$;0XOWLVHUYLFH0HGLD*DWHZD\V&acute;&sup3;&frac12;&frac14;&sup3;&frac12;&sup2;&cedil;&sup3;&acute;&sup3;&sup1;&copy;&cedil;&not;&sup1;&copy;&iexcl;
&middot;&cedil;&sup3;&sup2;}&frac12;&para;&ordm;&acute;&yen;&iquest;&macr;&cent;&shy;&macr;&sup3;&sup2;&sup3;&plusmn;&shy;&macr;&cent;&micro;&para;&sup3;}}y&acute;&para;&sup3;&sup3;&para;&iexcl;&frac34;&sup3;&sup2;&cedil;&yen;&shy;&laquo;&shy;&yen;&middot;&curren;&sup2;&uml;&copy;&middot;&not;&plusmn; &copy;&cedil;&yen;&uml;&iexcl;&macr;&cedil;&frac12;&yen;
((670&macr;&yen;&shy;670F7&shy;m&not;&deg;&micro;&middot;&copy;&shy;&raquo;}&sup2;&yen;&para;&plusmn;&cent;&sup2;&shy;&middot;&not;&raquo;&cedil;&not;&raquo;}&plusmn;&acute;&sup3;&para;&sup3;&curren;&sup2;&sup2;&yen;
&acute;&para;&sup3;&brvbar;&deg;&not;&sup1;&sup3;&curren;&sup2; &sup2;&yen;&cedil;&frac12;&acute;&ordm;&sup1;&sup3;&curren;&sup2;&yen;&acute;&cent;&cedil;&not;&sup2;&acute;&yen;&para;&yen;&macr;&cedil;&ordm;&acute;&para;&sup3;&middot;&shy;&cedil; &middot;&cedil;&sup3;&macr;&sup3;&shy;&sup2;&cent;&cedil;&sup3;&acute;&sup3;&sup1;&copy;&middot;&iexcl;&yen;&cedil;&sup3;&frac12;
&sup2;&cedil;&copy;&para;&sup2;&copy;&cedil;
http://www.lucentdocs.com/ins
Euroopan unionin s&auml;&auml;ntelystandardi
CE-merkint&auml;
Lucent Technologies vakuuttaa t&auml;ten, ett&auml; PacketStar PSAX 1000 (-48 V dc ja
220 V vaihtovirtaa), PSAX 1250 (-48 V dc ja 220 V vaihtovirtaa), PSAX 2300,
ja PSAX 4500 Media Gatewayt ja t&auml;ss&auml; julkaisussa dokumentoidut laitteet,
t&auml;ytt&auml;v&auml;t seuraavien neuvoston direktiivien keskeiset vaatimukset ja asiaankuuluvat m&auml;&auml;r&auml;ykset:
• Pienj&auml;nnite 72/23/EY
• S&auml;hk&ouml;magneettinen yhteensopivuus (EMC) 89/336/EY
• Radiolaitteet ja telep&auml;&auml;telaitteet 1999/5/EY
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
vi
Release 10.0.0
255-700-584
Lucent PacketStar PSAX Multiservice Media Gatewayt, joita k&auml;ytet&auml;&auml;n
Euroopan talousalueella, on tarkoitettu liitett&auml;v&auml;ksi E1-, E3-, STM-1- ja
STM-4c-verkkoihin. EU:n vaatimustenmukaisuusvakuutus voidaan n&auml;hd&auml;
tai tulostaa seuraavalta julkiselta Internet-sivulta:
http://www.lucentdocs.com/ins
Norme r&eacute;glementaire de l’Union europ&eacute;enne
Label CE
Lucent Technologies d&eacute;clare en ceci que les passerelles de m&eacute;dia multiservices PacketStar PSAX 1000 (-48 V c.c. et 220 V ca), PSAX 1250 (-48 V c.c. et
220 V ca), PSAX 2300, et PSAX 4500 sont conformes aux exigences essentielles et autres dispositions pertinentes des directives suivantes du Conseil:
• Basse tension 72/23/CEE
• Compatibilit&eacute; &eacute;lectromagn&eacute;tique (CEM) 89/336/CEE
• Mat&eacute;riel radio et terminaux de t&eacute;l&eacute;communications 1999/5/CE
Les passerelles de m&eacute;dia multiservices PacketStar PSAX de Lucent, commercialis&eacute;es dans l’Espace &eacute;conomique europ&eacute;en sont destin&eacute;es aux connexions
&agrave; des r&eacute;seaux E1, E3, STM-1 et STM-4c. Les d&eacute;clarations de conformit&eacute; CE
peuvent &ecirc;tre consult&eacute;es ou imprim&eacute;es &agrave; partir du site Internet d’acc&egrave;s public:
http://www.lucentdocs.com/ins
Normativa dell’Unione Europea
Apposizione del
marchio CE
La Lucent Technologies dichiara che i gateway multiservizio PacketStar
PSAX 1000 (-48 V dc e 220 V c.a.), PSAX 1250 (-48 V dc e 220 V c.a.),
PSAX 2300, e PSAX 4500 inclusi quelli documentati in seguito, rispondono ai
requisiti essenziali ed ad altre norme rilevanti delle seguenti direttive del
Consiglio:
• Direttiva 72/23/CEE “Basse tensioni”
• Direttiva 89/336/CEE sulla compatibilit&agrave; elettromagnetica
• Direttiva 1999/5/CE riguardante le apparecchiature radio e le apparecchiature terminali di telecomunicazione
I gateway multiservizio PacketStar PSAX della lucent, impiegati nell’area economica europea (EEA), sono concepiti per il collegamento con reti E1, E3,
STM-1 e STM-4c. Le dichiarazioni di conformit&agrave; CE possono essere visionati
o stampati presso il seguente sito Internet di pubblico accesso:
http://www.lucentdocs.com/ins
Norm van de Europese Unie
CE-markering
Lucent Technologies verklaart hierbij dat de PacketStar PSAX 1000 (-48 V dc
en 220V wisselstroom), PSAX 1250 (-48 V dc en 220V wisselstroom),
PSAX 2300, en PSAX 4500 Multiservice Media Gateways voldoen aan de
essenti&euml;le vereisten en andere relevante bepalingen van de volgende Richtlijnen van de Raad:
• Laagspanning 72/23/EEG
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
vii
• Elektromagnetische compatibiliteit (EMC) 89/336/EEG
• Radioapparatuur en telecommunicatie-eindapparatuur 1999/5/EG
De Lucent PacketStar PSAX Multi Service Media Gateways die in de Europese
Economische Ruimte (EER) zijn ingezet, zijn bestemd voor aansluiting op E1,
E3, STM-1 en STM-4c netwerken. DE EU-verklaringen van overeenstemming kunnen worden bekeken of afgedrukt op de volgende Internet-site met
openbare toegang:
http://www.lucentdocs.com/ins
Padr&atilde;o Regulador da Uni&atilde;o Europeia
Marca CE
A Lucent Technologies vem por este meio declarar que os Concentradores de
Acesso PacketStar PSAX 1000 (-48 V dc e 220V CA), PSAX 1250 (-48 V dc e
220V CA), PSAX 2300, e PSAX 4500 obedecem aos requisitos essenciais e a
outras disposi&ccedil;&otilde;es relevantes das seguintes Directivas do Conselho:
• Baixa Voltagem 72/23/EEC
• Compatibilidade Electromagn&eacute;tica (EMC) 89/336/EEC
• Equipamento de R&aacute;dio e Equipamento Terminal de Telecomunica&ccedil;&otilde;es
1999/5/EC
Os Concentradores de Acesso PacketStar PSAX da Lucent instalados na &Aacute;rea
Econ&oacute;mica Europeia (EEA) foram concebidos para serem ligados a redes do
tipo E1, E3, STM-1 e STM-4c. As Declara&ccedil;&otilde;es de Conformidade CE podem ser
vistas ou impressas no seguinte s&iacute;tio de acesso p&uacute;blico da Internet:
http://www.lucentdocs.com/ins
Norma reguladora de la Uni&oacute;n Europea
Marcas de la CE
Por el presente, Lucent Technologies declara que las pasarelas de medios
multiservicio PacketStar PSAX 1000 (-48 V cc y 220 V ca), PSAX 1250
(-48 V cc y 220 V ca), PSAX 2300, y PSAX 4500 Multiservice Media Gateways, inclusive el equipo documentado en esta publicaci&oacute;n, est&aacute;n en conformidad con los requisitos esenciales y otras disposiciones pertinentes de las
siguientes directrices del consejo:
• Bajo voltaje 72/23/EEC
• Compatibilidad electromagn&eacute;tica (EMC) 89/336/EEC
• Equipo de radio y equipo de terminales de telecomunicaciones 1999/5/EC
Las pasarelas de medios multiservicio Lucent PacketStar PSAX Multiservice
Media Gateways desplegadas en el &aacute;rea econ&oacute;mica europea (European Economic Area, EEA) est&aacute;n destinadas a conectarse en redes E1, E3, STM-1 y
STM-4c. Las declaraciones de conformidad de la CE pueden verse o
imprimirse en el siguiente sitio Internet de acceso p&uacute;blico:
http://www.lucentdocs.com/ins
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
viii
Release 10.0.0
255-700-584
Europeiska unionens standardf&ouml;rordning
CE-m&auml;rkning
Lucent Technologies deklarerar h&auml;rmed att PacketStar PSAX 1000
(-48 V likstr&ouml;m och 220 V v&auml;xelstr&ouml;m), PSAX 1250 (-48 V likstr&ouml;m och 220 V
v&auml;xelstr&ouml;m), PSAX 2300, och PSAX 4500 Multiservice Media Gateways, inklusive den i denna publikation dokumenterade utrustning, uppfyller de
v&auml;sentliga kraven och andra relevanta best&auml;mmelser som g&auml;ller enligt f&ouml;ljande Europar&aring;dsdirektiv:
• L&aring;gsp&auml;nning 72/23/EEC
• Elektromagnetisk kompatibilitet (EMC) 89/336/EEC
• Radioutrustning och telekommunikationskopplingsutrustning 1999/5/EC
Lucent PacketStar PSAX Multiservice Media Gateways, som &auml;r placerad i EEA
(European Economic Area), &auml;r avsedd f&ouml;r att anslutas till E1, E3, STM-1 och
STM-4c n&auml;tverk. Europar&aring;dets Konformitetsdeklarationer kan ses p&aring; bildsk&auml;rm eller skrivas ut p&aring; f&ouml;ljande, f&ouml;r allm&auml;nheten tillg&auml;ngliga Internet-st&auml;lle:
http://www.lucentdocs.com/ins
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
ix
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
x
Release 10.0.0
255-700-584
Table of Contents
Legal Notices, Safety, and Regulatory Information . . . . . . . . . . . . . . . . . iii
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Software and Hardware Limited Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Warranty Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Safety Warnings and Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Regulatory Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Safety and Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Telecommunications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
European Union Regulatory Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
xiv
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-1
Purpose of This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Audience for This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
What You Should Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Related Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Lucent Technologies Information Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Product Information Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Printed Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Other Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
About Lucent Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
For More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
About the PacketStar PSAX Product Family. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
PSAX 1000 Multiservice Media Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
PSAX 1250 Multiservice Media Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
xi
Table of Contents
PSAX 2300 Multiservice Media Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
PSAX 4500 Multiservice Media Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Text Types Used in This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
. 1-5
1-5
Icons and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1-5
Use of Command Description Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-6
Use of Field Description Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-6
General Navigational Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1-7
Selecting Options, Fields, and Commands Using the Console Interface . . . . . . . . . . . 1-7
1-7
Help Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1-8
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1-9
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Comments on This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
2
Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-1
Overview of This Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-1
Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2
Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2-4
Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-5
Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-5
Performance and Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-6
Module Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-6
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-7
Loopback Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-7
3
3-1
Configuring Ports and Channels Using the Console . . . . . . . . . . . . . . . . . . . 3-1
Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-1
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-1
Obtaining General Module Data and Accessing Ports and Channels. . . . . . . . . . . . . . . . . 3-1
3-1
Accessing the Equipment Configuration Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-1
Alarm Status Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3-6
Configuring the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-7
Configuring Ports and Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3-8
Viewing Port Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Configuring IMA Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Viewing Group Channel Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
Saving the Equipment Configuration and Logging Off . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Provisioning Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
xii
Release 10.0.0
255-700-584
Table of Contents
A
Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Overview of This Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
To the PSAX 12-Port BNC Patch Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
To the PSAX 24-Port RJ Patch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
To the PSAX 48-Port RJ Patch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
B
Reference Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Overview of This Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Avoiding Common Errors When Configuring Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Optimizing SVC Call Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Connection Type by Interface Type Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Interface Type by I/O Module Type Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
Module Alarm Status Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7
ATM Service Categories in the PSAX System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-9
ATM Service Category Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-9
Priority of ATM Service Categories in the PSAX System . . . . . . . . . . . . . . . . . . . . . . . .B-9
ATM TS, UPC, and VI Configuration Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-10
ATM Traffic Shaping Capability by Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-11
ATM Traffic Shaping Sample CPS Calculation Table . . . . . . . . . . . . . . . . . . . . . . . . . .B-13
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
xiii
List of Figures
1-1
Field Description Table Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-2
Main Menu Help Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
2-1
21-Port High-Density E1 IMA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2
21-Port High-Density E1 IMA Modules Connected to 48-port RJ Patch Panel (front view of
chassis, patch panel, fan tray, and heat deflector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-3
21-Port High-Density E1 IMA Modules Connected to 48-port RJ Patch Panel (back view of
patch panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2-3
2-3
2-4
21-Port High-Density E1 IMA Module Connected to a 12-port BNC Patch Panel (front view of
chassis and patch panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2-5
21-Port High-Density E1 IMA Module Connected to a 12-port BNC Patch Panel (back view of
patch panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2-4
2-4
2-6
Loopback Configuration Options on the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
3-1
Sample Equipment Configuration Window on a PSAX 1000
System (Page 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-2
Sample Equipment Configuration Window on a PSAX 1250
System (Page 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-3
Sample Equipment Configuration Window on a PSAX 2300 or
PSAX 4500 System (Page 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-4
Sample Equipment Configuration Window on a PSAX 1000, PSAX 2300, or
PSAX 4500 System (Page 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3-5
Sample Equipment Configuration Window on a PSAX 1250
System (Page 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3-6
Console Interface Main Menu Window (Equipment Configuration Selected) . . . . . . . . . . . . 3-8
3-7
Equipment Configuration Window (As Displayed on the PSAX 1250, PSAX 2300, and PSAX
4500 Console) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3-8
Equipment Configuration Window (As Displayed on the PSAX 1000 Console) . . . . . . . . . . 3-9
3-9
21-Port High Density E1 IMA Module Configuration Window . . . . . . . . . . . . . . . . . . . . . . 3-10
3-10
21-Port High Density E1 IMA Module Port and Channel Configuration Window . . . . . . . 3-11
3-11
3-11
21-Port High Density E1 IMA Port Statistics Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
3-12
High-Density E1 IMA Group Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3-13
IMA Virtual Group Channel Configuration Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
3-14
IMA Group Configuration Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
3-15
IMA Group Channel Statistics Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
3-16
Save Configuration [Modified] (Before Saving) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
B-1
Combining the UPC Feature and Either the TS or VI Feature on a Connection . . . . . . . . . . B-11
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
xiv
List of Tables
1-1
Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1-2
Command Description Table Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-3
System Responses to Selecting Options, Fields, or Commands. . . . . . . . . . . . . . . . . . . . . . . . 1-7
1-4
Shortcut Keys for Navigating Console Interface Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
2-1
Physical Hardware Specifications for the PSAX I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-2
Performance and Power Specifications for the PSAX Module . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-3
LED Indicators for the 21-Port High-Density E1 IMA Module . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
3-1
Equipment Configuration Window Field Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3-2
Module Alarm Status Descriptions on the Equipment Configuration Window . . . . . . . . . . . . 3-7
3-3
21-Port High Density E1 IMA Module Port and Channel Configuration Window Field
Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3-12
3-4
21-Port High-Density E1 IMA Module—Line Status Alarm Descriptions . . . . . . . . . . . . . . . . 3-15
3-15
3-5
21-Port High Density E1 IMA Port Statistics Window Field Descriptions . . . . . . . . . . . . . . . . 3-18
3-18
3-6
IMA Virtual Group Channel Configuration Window Field Descriptions . . . . . . . . . . . . . . . . 3-21
3-21
3-7
IMA Group Configuration Window Field Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
3-23
3-8
IMA Group Channel Statistics Window Field Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
3-33
3-9
Messages Generated after the Save Configuration Process . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
3-35
A-1
21-Port High-Density E1 IMA Module Connector, Cable, and PSAX 12-Port BNC Patch Panel
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B-1
Connection Type by Interface Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
B-2
Interface Type by I/O Module Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
B-3
Module Alarm Status Descriptions on the Equipment Configuration Window . . . . . . . . . . . . B-7
B-4
PSAX System-Supported Quality of Service Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
B-5
Mapping ATM Service Categories to PSAX System Priority Levels. . . . . . . . . . . . . . . . . . . . . B-10
B-10
B-6
ATM Traffic Shaping, UPC Support, and VI Support Configuration Compatibility. . . . . . . . . B-10
B-7
ATM Traffic Management Capabilities by Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
B-11
B-8
ATM Traffic Shaping CPS Calculation Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13
B-13
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
xv
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
xvi
Release 10.0.0
255-700-584
1
Getting Started
Purpose of This Guide
The PacketStar&reg;21-Port High-Density E1 IMA Module User Guide provides a
description of the 21-Port High-Density E1 IMA module. It also provides
information on how to configure the module ports and channels.
For information on configuring interfaces and provisioning connections
through the PSAX console interface, see the PacketStar&reg; PSAX Connections Provisioning Guide. If the Navis&reg; EMS-PSAX interface is being used, see the
Navis&reg; EMS-PSAX Interface and Connection Provisioning Guide.
Note:
If you are using this module for the first time, you should read
through this guide in its entirety before beginning the configuration process. The chapters in this guide are arranged in the logical
order of normal configuration and should be performed in that
order for the module to operate successfully.
Audience for This Guide
The information in this guide is intended for users who will configure ports
and channels for the 21-Port High-Density E1 IMA module in the PSAX Multiservice Media Gateway system.
What You Should Know
Before you use this document or operate a PSAX system, you should already
understand and have experience with the following:
• ATM Forum, Frame Relay Forum, and other telecommunications specifications
• Ethernet network capabilities
• Internet Protocol capabilities
• Data network design
• Telephony network design
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
1-1
Chapter 1 Getting Started
Related Reading
Related Reading
Lucent Technologies Information Products
Product Information
Library
To install, operate, and configure your PSAX system and I/O and server modules, read the PSAX publications provided on your Lucent Technologies
PacketStar&reg; PSAX Multiservice Media Gateways Product Information Library
CD-ROM.
Printed Documents
For your convenience, many of the documents included on the PacketStar&reg;
PSAX Multiservice Media Gateways Product Information Library CD-ROM are also
available in printed form. You can order these documents through the Lucent
Technologies Customer Information Center Web site at:
http://www.lucentdocs.com.
Other Publications
Numerous books are currently available on the subject of basic telecommunications technology and specific protocols. In addition to such general reading,
you should also be familiar with the industry specifications identified in this
guide.
About Lucent Technologies
Lucent Technologies is the communications systems and technology company formed through the restructuring of AT&amp;T. We bring with us a tradition
of more than 125 years of experience and a dedication to superior customer
service.
Lucent Technologies manufactures, sells, and services a complete line of customer premises communications units, and commercial and multimedia
communications and messaging systems designed and supported by our
research and development unit, Bell Laboratories.
Our legacy and our spirit of innovation allow Lucent to provide our customers with the tools needed to communicate effectively, any time and anywhere, and to integrate the latest technologies into real-life solutions that
help make business work.
For More Information
To learn more about the PacketStar PSAX family of Multiservice Media Gateways and the complete line of Lucent Technologies products, visit our Web
site at http://www.lucent.com.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
1-2
Release 10.0.0
255-700-584
Chapter 1 Getting Started
About the PacketStar PSAX Product Family
About the PacketStar PSAX Product Family
Lucent Technologies provides a complete range of PSAX Multiservice Media
Gateways in the PacketStar PSAX family.
PSAX 1000 Multiservice Media Gateway
The PacketStar PSAX 1000 Multiservice Media Gateway is designed to provide
a full range of central office-based multiservice media gateway functions in a
small, competitively-priced package suitable for customer premise deployment. Ideal for central office, large enterprise, or wireless cell site multiservice media gateway applications, the PSAX 1000 system provides highly reliable network access for time-division multiplex voice, frame relay,
10/100BASE-T Ethernet, and ATM data applications.
When it is functioning in a redundant operating mode and after it has experienced a single-point failure, the PSAX 1000 system provides up to 630 Mbps
of ATM cell bus capacity. The total ATM cell bus capacity of the system may
also be scaled to provide nonblocking, nonredundant chassis bandwidths
beyond 630 Mbps.
Supporting up to five slots (19–inch chassis) for I/O and server modules—with a full range of interfaces such as DS0A, DS1/E1, DS3/E3, OC-3,
OC-3c/STM-1, OC-12c/STM-4c, 10/100BASE-T Ethernet, and serial—the
PSAX 1000 system is a cost-effective access switch solution for connecting to
legacy equipment.
PSAX 1250 Multiservice Media Gateway
The PacketStar PSAX 1250 Multiservice Media Gateway is designed to provide a full range of central office-based multiservice ATM access functions.
Ideal for the central office or a large enterprise’s multiservice media gateway,
the PSAX 1250 system provides highly reliable network access for time-division multiplex voice, frame relay, 10/100BASE-T Ethernet, and ATM data
applications.
When it is functioning in a redundant operating mode and after it has experienced a single-point failure, the PSAX 1250 system provides up to 600 Mbps
of ATM cell bus capacity. The total ATM cell bus capacity of the system may
also be scaled to provide nonblocking, nonredundant chassis bandwidths
beyond 600 Mbps.
Supporting 10 slots (19-inch chassis) or 14 slots (23-inch chassis) for I/O and
server modules—with a full range of interfaces such as DS0A, DS1/E1,
DS3/E3, OC-3, OC-3c/STM-1, OC-12c/STM-4c, 10/100BASE-T Ethernet,
and serial—the PSAX 1250 system is a cost-effective access switch solution
for interworking with legacy equipment.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
1-3
Chapter 1 Getting Started
About the PacketStar PSAX Product Family
PSAX 2300 Multiservice Media Gateway
The PacketStar PSAX 2300 Multiservice Media Gateway offers carrier-grade,
high-density multiservice ATM access functions. Designed as the multiservice
media gateway for the central office or for a large enterprise customer, the
PSAX 2300 system provides network access for time-division multiplex
voice, frame relay, 10/100BASE-T Ethernet, and ATM data applications.
When it is functioning in a redundant operating mode and after it has experienced a single-point failure, the PSAX 2300 system provides up to 1.9 Gbps
of ATM cell bus capacity. The total ATM cell bus capacity of the system may
also be scaled to provide nonblocking, nonredundant chassis bandwidths
beyond 1.9 Gbps.
Supporting 15 slots for I/O and server modules—with provisions for OC-3,
OC-3c/STM-1, and OC-12c/STM-4c interfaces with 1:1 protection, 1:1 DS1
module protection switching, and a full range of interfaces such as DS0A,
DS1/E1, DS3/E3, 10/100BASE-T Ethernet, and serial—the PSAX 2300 system solves demanding and diverse network design challenges with ease.
PSAX 4500 Multiservice Media Gateway
The PacketStar PSAX 4500 Multiservice Media Gateway provides carrier-class
reliability, with an unmatched range of service capabilities, end-to-end traffic
prioritization, “any-service, any-channel” flexibility, and breakthrough voice
technology. Ideal for the central office or a large enterprise multiservice
media gateway, the PSAX 4500 system provides highly reliable network
access for time-division multiplex voice, frame relay, 10/100BASE-T Ethernet, and ATM data applications.
When it is functioning in a redundant operating mode and after it has experienced a single-point failure, the PSAX 4500 system provides up to 4.2 Gbps
of ATM cell bus capacity. The total ATM cell bus capacity of the system may
also be scaled to provide nonblocking, nonredundant chassis bandwidths
beyond 4.2 Gbps.
The high-performance midplane design supports 15 interface slots. Module
protection for two groups of four or six multiport DS3, STS-1e, or E3 modules is provided via an N:1 protection scheme using rear access line interface
modules. The protection module provides backup so that on the failure of
any one of the modules in a group, traffic is maintained. A single PSAX 4500
system at the edge of the carrier network can transition traffic from a large
number of network customers over high-speed DS1/E1 IMA, DS3/E3, OC-3,
OC-3c/STM-4c, and OC-12c/STM-4c trunks into the ATM core, managing
the whole quickly and efficiently, down to the individual permanent virtual
circuit.
Through the use of the latest DSP voice technology, the PSAX 4500 system
supports advanced voice traffic over ATM (VToA) services for up to 6048 DS0
channels. As a multiservice media gateway—with H.248 call control, CAS,
PRI, GR-303, and V5.2 protocols, 3-Port DS3/STS-1e, 1-Port OC-3/STM-1
CES, and Tones and Announcements modules—the PSAX 4500 system provides packet solutions for voice over xDSL, trunking, tandem, and PRI offload
switching.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
1-4
Release 10.0.0
255-700-584
Chapter 1 Getting Started
Conventions
Conventions
Text Types Used in This Document
This guide uses a different typeface to denote text displayed on console interface windows and equipment, as well as data you enter. Table 1-1 shows how
each typographical convention is used.
Table 1-1. Text Conventions
Appearance
How it is used
SANS SERIF BOLD, ALL CAPS
Labels on module panels, chassis faceplates, or other
hardware
Fixed-width normal
Message text displayed on the user interface window
Serif bold
• Button name (GUI interface) or command name
(console interface) on the user interface window
• Literal text for values that the user types or selects
from predefined sets of values for fields
• Commands or literal argument values
Fixed-width bold
System prompts displayed on the user interface window
Serif italics
• A variable name or string for which you will substitute your own information
• An argument or parameter on a command line for
which you will substitute your own information
Icons and Symbols
Refer to the procedures within this guide for important safety information
and proper procedures.
Standard icons and symbols to alert you to dangers, warnings, cautions, and
notes are described as follows:
! DANGER:
Warnings for a personal injury hazard are identified by this format.
! WARNING:
Warnings relating to risk of equipment damage or failure are identified
by this format.
! CAUTION:
Warnings relating to risk of data loss or other general precautionary
notes are identified by this format.
Note:
Identifies additional information pertinent to the text preceding
this note.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
1-5
Chapter 1 Getting Started
Conventions
Use of Command Description Tables
All illustrations for configuration windows in this guide for the PSAX system
console interface are followed by a command description table describing the
command functions displayed on the window (near the bottom of the window). You should read all the information in the command description table,
especially when first using a window, because these descriptions may have
special instructions or configuration constraints provided in the Function column by use of the Note: text convention (see Table 1-2).
Table 1-2. Command Description Table Example
Command
Function
Bring All Interfaces Brings the out-of-service configured interfaces to in-service status.
Into Service
Note: In GR-303 configuration, it is critical to bring into service
only those channels actively configured with DS1 ports.
Use of Field Description Tables
For all illustrations for configuration windows in this guide for both the
PSAX system console interface and the EMS-PSAX, the field description
tables normally follow the command description tables. Field description
tables define the editable and the display-only fields, their functions, valid
values, and constraints, if applicable. As in the command description tables,
the Note: text convention is also used, where appropriate, in the field description tables to alert the user to special instructions or configuration constraints
(see Figure 1-1).
Identifies editable fields
or display-only fields on
screens
Identifies initial field
value default
Field Name
Field Values
Interface Type
Identifies available
range for field value
when applicable
Default: 0
Range: 0-22
Format: Numeric
Describes the function of the field
and special instructions for
configuring modules
Description
Specifies the type of end-to-end connection
protocol that governs the transmission parameters
for this configured port and channel interface.
Note: When certain types of interfaces are selected in this field, other configuration fields are displayed on this window.
Identifies field value format as
Numeric, Predefined Alphanumeric,
Hexadecimal, or Valid Dotted Quad.
Decribes special instructions or
configuration constraints
Figure 1-1. Field Description Table Example
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
1-6
Release 10.0.0
255-700-584
Chapter 1 Getting Started
General Navigational Guidelines
General Navigational Guidelines
Selecting Options, Fields, and Commands Using the Console Interface
Follow these guidelines to select an option, field, or command on the PSAX
console interface windows and to navigate through the windows:
• To select an option, field, or command, do one of the following:
~ Press the Up, Down, Left, or Right Arrow to highlight (reverse video
image) the option name, field name, or command you want to select and
press Enter as many times as necessary until the field choice you want is
displayed.
~ Use the alternate keys, K=UP, H=LEFT, L=RIGHT to highlight (reverse
video image) the option name, field name, or command you want to
select and press Enter. (You can optionally redefine these alternate keys
from the User Options window, which is accessible from the Console
Interface Main Menu window.)
~ To quickly select a command, you can also simultaneously press Ctrl and
the letter underlined in the command.
Once an option name, field, or command is selected, the system responds
as described in Table 1-3.
Table 1-3. System Responses to Selecting Options, Fields, or Commands
For a selected...
the following occurs:
option name
The window corresponding to the option name is displayed.
field
The following variations occur:
• The field entry area is blank or contains the default or previously
entered value. Press Enter to enter or change data in this field. Press
Enter again to exit edit mode.
• The field entry area, like the field name, is displayed in reverse video
image and contains a predefined set of values, which you can view or
select by pressing Enter to navigate forward through these values. To
navigate backward through these field values, press Ctrl+H or the
Backspace key.
Read-only fields, which you cannot change, are enclosed in square brackets (example: [LineStatus]).
command
The following variations occur:
• A message in the information line indicating an error or successful completion of the command is displayed.
• The next higher level or previous window (window name) is displayed.
• The next lower level or succeeding window (window name) is displayed.
• To navigate through the Console windows, use the shortcuts listed in
Table 1-4.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
1-7
Chapter 1 Getting Started
Help Information
Table 1-4. Shortcut Keys for Navigating Console Interface Windows
If you want to...
press...
redisplay the previous window
Ctrl+B on the window.
redisplay the Console Interface Main Menu window
Ctrl+G on the window.
refresh the window
Ctrl+R on the window.
On all the PSAX system windows, each command or menu option has an
underlined letter. The control key plus an underlined letter is a shortcut to
that command or menu option. You can use the navigation keys and hotkeys
with the Caps Lock key on or off. Always observe the status line at the bottom of the window for instructions and information.
Help Information
The Help windows are accessible from any window in the PSAX system console interface. To access the Help windows, press the ? (Question Mark) key
on any window. In addition to the Help windows, the Console Interface windows display contextual help in the information line at the bottom of each
window. Contextual help provides information about the command or field
currently highlighted on that window. The information line also displays
error codes and responses to commands. All responses and notifications are
recorded in a trap log. See the PacketStar&reg; PSAX Simple Network Management
Protocol (SNMP) Trap Reference Guide for details on displaying the trap log and
obtaining explanations of the trap messages.
To view the Help windows from the Console Interface Main Menu window,
perform the following procedure.
Begin
1 On the window for which help is desired, press the ? (question mark)
key.
The Help window for the current console window is displayed (see
Figure 1-2).
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
1-8
Release 10.0.0
255-700-584
Chapter 1 Getting Started
Technical Support
Your site name appears here
after initial configuration
Information Line
Figure 1-2. Main Menu Help Window
2 To display the remaining Help windows for the current console window,
press the Down Arrow key.
3 To scroll backward through the Help windows for the current console
window, press the Up Arrow key.
4 To exit Help and return to the current console window, press the Enter
key.
End
Technical Support
If you experience a problem with the 21-Port High-Density E1 IMA module,
refer to the Lucent Technologies Product Warranty Registration Information, which
accompanied your shipment, for instructions on obtaining support in your
area.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
1-9
Chapter 1 Getting Started
Before You Begin
Before You Begin
Before you start configuring and using your new 21-Port High-Density E1
IMA module, be sure you:
• Record your site-specific specifications such as the IP addresses you will
use, and the connections and interfaces you will need. Decide which user
names and passwords you will assign.
• Make sure you have IP connectivity to all PSAX devices to be managed
• Determine the numbering scheme for any in-band management connections you will be using
Comments on This Guide
To comment on the PacketStar&reg;21-Port High-Density E1 IMA Module User Guide,
please complete the comment card at the following web address:
http://www.lucent-info.com/comments/
You can also email your comments to [email protected].
Include the following information:
Title: PacketStar&reg;21-Port High-Density E1 IMA Module User Guide
Release number: Release 10.0.0
Document number: 255-700-584
Issue number: Issue 1
Publication date: December 2004
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
1-10
Release 10.0.0
255-700-584
2
Module Description
Overview of This Module
The 21-Port High-Density E1 IMA module (see Figure 2-1) provides a line
rate of 2.048 Mbps per port. The module’s inverse multiplexing for ATM
capabilities permit a user to strap 2 to 21 of the physical ports together to create ATM interfaces that support up to 43 Mbps of bandwidth. A maximum of
10 IMA groups may be configured per module.
This module offers native E1 ATM services and E1 IMA services, including
permanent virtual circuits, soft permanent virtual circuits, and switched virtual circuits. The module supports the Traffic Shaping feature on ATM UNI
v3.n, UNI v4.0, IISP, PNNI, and ILMI interfaces. This functionality enables
service providers to offer both individual unchannelized E1 ATM services
(without IMA overhead) and multiple E1 IMA group services using a single
module.
Using the IMA protocol, this module provides an effective method of combining the transport bandwidths of multiple E1 links that are grouped to collectively provide higher intermediate rates. This technique involves inverse
multiplexing and de-multiplexing of ATM cells in a cyclical fashion among
links grouped to form a higher bandwidth logical link whose rate is approximately the sum of the link rates. This is referred to as an IMA group. From
the system’s viewpoint, these IMA groups are simply new ATM interfaces
sized as multiples of E1. (Refer to Inverse Multiplexing for ATM Version 1.1, afphy-0086.001.)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
2-1
Chapter 2 Module Description
Connection Options
FAIL
ACTIVE
PORTS 1-12
PORTS 13-21
HD E1
IMA
Figure 2-1. 21-Port High-Density E1 IMA Module
Connection Options
The 21-Port High-Density E1 IMA module connects to user equipment via a
standard 10-foot Lucent cable (COMCODE 300550639) with an RJ-48H connector. Typically, this cable is used to connect the module to one of the following patch panels within the same or an adjacent Telco frame:
• PSAX 12-Port BNC Patch Panel (impedance 75 ohms)
• PSAX 24-Port RJ Patch Panel (impedance 120 ohms)
• PSAX 48-Port RJ Patch Panel (impedance 120 ohms)
The PSAX 24-Port RJ Patch Panel uses ports 1–21 (ports 22-24 are not used).
The PSAX 48-Port RJ Patch Panel uses ports 1–21 and 25–45 (ports 22–24
and 46–48 are not used).
The Lucent cable can be extended for short-haul links of up to 500 feet (with
5 dB cable loss) by connecting the Lucent cable to an Avaya cable (p/n
1010025AGY CUSTL, at -1 dB per 100 feet), or equivalent. Use RJ-48H connectors (for example, Cinch p/n 57-10500-271A and Cinch p/n
57-20500-7A) on the extension cable to link the Lucent cable to the
PSAX Patch Panels.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
2-2
Release 10.0.0
255-700-584
Chapter 2 Module Description
Connection Options
Figure 2-2 and Figure 2-3 show both connectors of two modules connected
to a PSAX 48-Port RJ Patch Panel (COMCODE 300298544). Figure 2-4 and
Figure 2-5 show one connector of a module connected to a PSAX 12-Port
BNC Patch Panel (COMCODE 300298569). Each port consists of a pair of
transmit and receive signals. These components are separately orderable.
Heat
Deflector
PORT 13-24
PORT 1-12
Patch
Panel
PacketStar36$;33
1.75&quot; SPACER
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
HD E1
IMA
HD E1
IMA
SERIAL
DS1
IMA
DS1
IMA
DS1
IMA
DS1
IMA
DS3
ATM
DS3
ATM
DS3
ATM
CPU2
CPU2
STRATUM
3 4
STRATUM
3 4
Power Supply
(110V AC)
Model 20N04
CLK LOS
CLK LOS
non-redundant
FAIL
FAIL
FAIL
FAIL
ACTIVE
ACTIVE
Power Supply
(110V AC)
Model 20N04
WARNINGS:
2
ETHERNET
PORTS 1-12
LOS
LOS
LOS
LOS
1
1
1
1
LOS
LOS
TX
TX
2
2
RX
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
RX
PORTS 13-21
PORTS 13-21
B
ATTACH POWER
CORD ONLY
DANGER: HIGH VOLTAGE WHEN UNIT IS
FULLY SEATED
IN CHASSIS
CONSOLE
TX
LOS
RX
CAUTION: DISCONNECT POWER BEFORE
CHANGING FUSE. REPLACE ONLY WITH
FUSE OF SAME TYPE AND RATING.
Power Supply A
PSAX1250 FAN TRAY
RX
LOAD
6
LOAD
LOS
TX
TX
RX
RX
WARNINGS:
SEE INSTALLATION
INSTRUCTIONS BEFORE
CONNECTING THIS MODULE
non-redundant
ENSURE FACILITY POWER
IS COMPATIBLE WITH
VOLTAGE RATING OF
THIS MODULE
2
4
LOS
5
ETHERNET
LOS
TX
CONSOLE
2
3
PORTS 1-12
PORTS 1-12
A
1
SEE INSTALLATION
INSTRUCTIONS BEFORE
CONNECTING THIS MODULE
ENSURE FACILITY POWER
IS COMPATIBLE WITH
VOLTAGE RATING OF
THIS MODULE
ATTACH POWER
CORD ONLY
DANGER: HIGH VOLTAGE WHEN UNIT IS
PSAX 1250
FULLY SEATED
IN CHASSIS
UNPLUG POWER CORD
BEFORE REMOVING
THIS MODULE
UNPLUG POWER CORD
BEFORE REMOVING
THIS MODULE
MULTIPLE POWER
CONNECTIONS,
DISCONNECT TWO
POWER CORDS
BEFORE SERVICING
CHASSIS
MULTIPLE POWER
CONNECTIONS,
DISCONNECT TWO
POWER CORDS
BEFORE SERVICING
CHASSIS
CAUTION: DISCONNECT POWER BEFORE
ACTIVE
Fuse A
CHANGING FUSE. REPLACE ONLY WITH
FUSE OF SAME TYPE AND RATING.
Power Supply B
ALARMS
Fuse B
FAN FAIL
Fan Tray
Non-redundant
-48 V
0.5 A
-48 V
0.5 A
1.0A
1.0A
Figure 2-2. 21-Port High-Density E1 IMA Modules Connected to 48-port RJ Patch
Panel (front view of chassis, patch panel, fan tray, and heat
deflector)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Figure 2-3. 21-Port High-Density E1 IMA Modules Connected to 48-port RJ Patch
Panel (back view of patch panel)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
2-3
Chapter 2 Module Description
Software Features
PacketStar36$;33
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
FAIL
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
HD E1
IMA
HD E1
IMA
SERIAL
DS1
IMA
DS1
IMA
DS1
IMA
DS1
IMA
DS3
ATM
DS3
ATM
DS3
ATM
CPU2
CPU2
STRATUM
3 4
STRATUM
3 4
Power Supply
( AC )
CLK LOS
CLK LOS
non-redundant
FAIL
FAIL
FAIL
FAIL
ACTIVE
ACTIVE
Power Supply
( AC )
WARNINGS:
2
PORTS 1-12
1
PORTS 1-12
A
3
LOS
LOS
LOS
LOS
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
LOS
LOS
TX
RX
4
CONSOLE
LOAD
LOAD
ATTACH POWER
CORD ONLY
DANGER: HIGH VOLTAGE WHEN UNIT IS
FULLY SEATED
IN CHASSIS
LOS
TX
TX
TX
RX
RX
RX
non-redundant
ENSURE FACILITY POWER
IS COMPATIBLE WITH
VOLTAGE RATING OF
THIS MODULE
RX
LOS
WARNINGS:
SEE INSTALLATION
INSTRUCTIONS BEFORE
CONNECTING THIS MODULE
SEE INSTALLATION
INSTRUCTIONS BEFORE
CONNECTING THIS MODULE
ENSURE FACILITY POWER
IS COMPATIBLE WITH
VOLTAGE RATING OF
THIS MODULE
ATTACH POWER
CORD ONLY
DANGER: HIGH VOLTAGE WHEN UNIT IS
FULLY SEATED
IN CHASSIS
UNPLUG POWER CORD
BEFORE REMOVING
THIS MODULE
UNPLUG POWER CORD
BEFORE REMOVING
THIS MODULE
MULTIPLE POWER
CONNECTIONS,
DISCONNECT TWO
POWER CORDS
BEFORE SERVICING
CHASSIS
MULTIPLE POWER
CONNECTIONS,
DISCONNECT TWO
POWER CORDS
BEFORE SERVICING
CHASSIS
6
-21
PORTS 1-12
6
PORTS 13-21
PORTS 13-21
5
ETHERNET
CONSOLE
TX
RX
LOS
ETHERNET
LOS
TX
Figure 2-4. 21-Port High-Density E1 IMA Module Connected to a 12-port BNC
Patch Panel (front view of chassis and patch panel)
1
1
RX
2
2
TX
RX
3
3
TX
RX
4
4
TX
RX
5
5
TX
RX
6
6
TX
RX
7
7
TX
RX
8
8
TX
RX
9
9
TX
RX
10
10
TX
RX
11
11
TX
RX
12
12
TX
RX
TX
Figure 2-5. 21-Port High-Density E1 IMA Module Connected to a 12-port BNC
Patch Panel (back view of patch panel)
You may also connect the 21-Port High-Density E1 IMA module to a 24-port
RJ Patch Panel (COMCODE 300298551). See the Packetstar&reg; PSAX CO Patch
Panel and Cable Installation Guide (255-700-117, Issue 2) for instructions.
Further connections to user equipment may be made per the specifications
outlined in ANSI T1.403-1999. See Appendix A, ”Pin Configurations,” for
more details.
Software Features
The 21-Port High-Density E1 IMA module supports the following protocols
and services:
• Protocols: ATM, IMA
• ATM services over IMA groups:
~ ATM UNI 3.0, 3.1, 4.0, and ILMI with traffic shaping
~ IISP user and IISP network with traffic shaping
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
2-4
Release 10.0.0
255-700-584
Chapter 2 Module Description
Hardware Features
~ ATM PNNI with traffic shaping
Hardware Features
The 21-Port High-Density E1 IMA module provides the following hardware
features:
• Number of ports: 21
• Connector type: 2 Mini-Champ connectors
• Line rate: 2.048 Mbps
• Physical interfaces supported: ITU-T G.703, ITU-T G.704
• Line encoding mode: HDB3 (default), AMI
• Loopback capabilities: line loopback, local loopback
• Line buildout: N/A
• Framing mode: CRC4-CAS
Hardware Specifications
Table 2-1 provides the general physical hardware and environmental specifications for the PSAX I/O module.
Table 2-1. Physical Hardware Specifications for the PSAX I/O Module
Specification
Description
Dimensions
17.3 cm H x 2.41 cm W x 24.1 cm D
(6.8 in. H x 0.95 in. W x 9.5 in. D)
Weight
0.59 kg (1.3 lb.)
Operating temperature range for all the 0&deg; to 50&deg; C (32&deg; to 122&deg; F)
PSAX 1250, PSAX 2300, and
PSAX 4500 systems
Operating temperature range for the
PSAX 1000 systems
For AC-powered PSAX 1000 systems:
0&deg; to 50&deg; C (32&deg; to 122&deg; F)
For DC-powered PSAX 1000 systems:
-20&deg; to 60&deg; C (-4&deg; to 140&deg; F) with a cold start minimum of
0&deg; C (32&deg; F)
Operating humidity range for all chassis 5% to 85% relative humidity
Operating altitude range for all chassis
60 meters (197 feet) below sea level to 4,000 meters
(13,123 feet) above sea level
Storage temperature range for all
chassis
-40&deg; to 70&deg; C (-40&deg; to 158&deg; F)
Storage humidity range for all chassis
0% to 90% noncondensing
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
2-5
Chapter 2 Module Description
Hardware Features
Performance and Power Specifications
Table 2-2 provides the chassis speed, power consumption, and memory allocation specifications for this PSAX module.
Table 2-2. Performance and Power Specifications for the PSAX Module
Module
23N34
21-Port
High-Density E1 IMA
1
2
3
Total
Amount of
SDRAM
24 MB
Module
Maximum
Program and
Input
Data Space
Buffer1
7 MB
4 MB
Output
Buffer2
Chassis
Speed3
13 MB
(212,992)
Low
Speed
Maximum
Power
Consumption
14.5 W
The I/O buffers carry 16,384 cells per megabyte.
Indicates the size of the output buffer followed by the maximum number of 64-byte cells in the output
buffer.
This column relates only to the speed at which the module communicates within the chassis. A high-speed
module will communicate at high speed (1.2 Gbps) in a chassis that has a high-speed bus (PSAX 4500
chassis). High-speed modules will communicate at 600 Mbps in any other chassis. Low-speed modules will
always communicate at 600 Mbps in any chassis.
Module Placement
The 21-Port High-Density E1 IMA module is installed in any PSAX chassis
slot intended to contain an I/O or server module. If you are installing the
module in a newly installed PSAX chassis, be sure to follow your facility site
plan for placing this module in the correct location in the chassis.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
2-6
Release 10.0.0
255-700-584
Chapter 2 Module Description
Loopback Configuration Options
LED Indicators
Table 2-3 describes how the light-emitting diode (LED) indicators on the
21-Port High-Density E1 IMA module faceplate respond to different module
conditions. These LEDs indicate if the module has been installed properly.
Table 2-3. LED Indicators for the 21-Port High-Density E1 IMA Module
Module
Status
Initial
Power-On
No
Configured
Ports
LED
One or
No Cable on
More
Port
Configured
Ports
Cable on
Port
FAIL
(red)
Lights
briefly1
Not lit
Lights only Not
when the
Applicable
module is
not functioning
Not
Applicable
ACTIVE
(green)
Lights
briefly1
Not lit
Lights only Not
when the
Applicable
module is
functioning properly
Not
Applicable
1
Note: After power is initially applied to the system and the system boot is
complete, the FAIL and ACTIVE LEDs indicate whether the module has no
configured ports (red), or one or more configured ports (green).
Loopback Configuration Options
To aid network troubleshooting and testing, loopback capability is provided
for the 21-Port High-Density E1 IMA module.
The loopback option on the module port and channel configuration window
for the module enables you to verify the integrity of a port by transmitting a
received signal back to the source. Selecting a loopback option is described in
the module configuration procedure.
Figure 2-6 illustrates the line loop, payload loop, and local loop options.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
2-7
Chapter 2 Module Description
Loopback Configuration Options
Line Loop
Payload Loop
Line Driver
Signal
Receiver
Port Connector
Port
Connector
Framing Chip
Backplane
Connector
Backplane
Connector
Local Loop
Line Driver
Receiver
Backplane
Connector
Figure 2-6. Loopback Configuration Options on the Module
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
2-8
Release 10.0.0
255-700-584
3
Configuring Ports and Channels
Using the Console
Overview of This Chapter
This chapter describes how to use the console interface to perform the
following tasks on the 21-Port High-Density E1 IMA module:
•
“Obtaining General Module Data and Accessing Ports and Channels”
•
“Configuring Ports and Channels”
•
“Configuring IMA Groups”
•
“Saving the Equipment Configuration and Logging Off”
Before You Begin
Be sure to complete the following tasks first before configuring the 21-Port
High-Density E1 IMA module:
•
Configure your basic system (see “Configuring the System for Your Site”
in the PacketStar&reg; PSAX Multiservice Media Gateway User Guide).
•
Configure the Stratum 3–4 module (see “Configuring the Stratum 3–4
Module” in the PacketStar&reg; PSAX Multiservice Media Gateway User Guide).
When configuring the 21-Port High-Density E1 IMA module using the console interface, display-only fields are displayed in square brackets ([ ]).
Obtaining General Module Data and Accessing Ports and
Channels
This section describes how to obtain product, model, version, and serial
number data about a module from the Equipment Configuration window. In
addition, the window provides operational status and alarm conditions on
each installed module. You also use this window to access the port and
channel configuration windows for the PSAX modules.
Accessing the Equipment Configuration Window
Perform the following procedure to access the Equipment Configuration window.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-1
Chapter 3 Configuring Ports and Channels Using the Console
Obtaining General Module Data and Accessing Ports and Channels
Begin
1 On the Console Interface Main Menu window, select the Equipment
Configuration option.
The Equipment Configuration window is displayed (see Figure 3-1
through Figure 3-5).
2 View the operational and alarm status, software version, PEC, and serial
number data of the installed modules.
3 When you are ready to begin configuring the ports and channels of the
module, select the line displaying the name of the module you want to
configure.
4 Proceed to the section, “Configuring the Ports,” for module configuration
procedures.
Note:
The sample Equipment Configuration windows in the following
figures may not show the actual module you are configuring.
These figures illustrate the variations of slot configurations for
the different PSAX chassis displayed on the Equipment Configuration window.
End
Figure 3-1.
Sample Equipment Configuration Window on a PSAX 1000
System (Page 1)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-2
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Obtaining General Module Data and Accessing Ports and Channels
Figure 3-2.
Sample Equipment Configuration Window on a PSAX 1250
System (Page 1)
Figure 3-3.
Sample Equipment Configuration Window on a PSAX 2300 or
PSAX 4500 System (Page 1)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-3
Chapter 3 Configuring Ports and Channels Using the Console
Obtaining General Module Data and Accessing Ports and Channels
Commands
Figure 3-4.
Sample Equipment Configuration Window on a PSAX 1000,
PSAX 2300, or PSAX 4500 System (Page 2)
Figure 3-5.
Sample Equipment Configuration Window on a PSAX 1250
System (Page 2)
The commands in this window have the following functions.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-4
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Obtaining General Module Data and Accessing Ports and Channels
Command
Function
Update Display
Refreshes the current status of the modules in the PSAX chassis.
Page Down
Displays the second page of the Equipment Configuration window. This command toggles with Page Up.
Page Up
Displays the first page of the Equipment Configuration window.
This command toggles with Page Down.
Interface by Name
Displays the Interface Name Table window on which you can
view all the interface names in the PSAX system.
Go Back to Main Menu
Redisplays the Console Interface Main Menu window.
Field Description
The display-only fields on this window are described in Table 3-1.
Table 3-1. Equipment Configuration Window Field Descriptions
Field Name
Field Value
Description
Slot
Default: N/A
Displays the slot number in the PSAX chassis.
Range: 1–25, depends
on chassis type
Format: Numeric
Module Type
Default: N/A
Range: N/A
Format: Predefined
Displays the type of the module in the slot. When a
module is inserted into the chassis, its name is displayed in the Module Type field next to the slot number. When the module is removed from the chassis, its
name is no longer displayed in the Module Type field
and is replaced with None.
Status
Default: Unknown
Range: N/A
Format: Predefined
Displays the operational status of the module.
Unknown
Indicates that the module has not been configured.
Primary
Indicates one of the following:
• at least one port or channel on an I/O module has
been configured.
• a CPU module is functioning as the primary CPU
module.
Standby
Indicates one of the following:
• a module in redundant systems is operating as the
standby (backup) module to the primary (active)
module.
• a CPU module in redundant systems is functioning
as the standby (backup) CPU module.
Default: No Alarm
Range: N/A
Format: Predefined
Displays the present alarm condition of the module.
For the alarm status conditions, see the table “Alarm
Status Descriptions for Modules” following this table.
Alarm Status
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-5
Chapter 3 Configuring Ports and Channels Using the Console
Obtaining General Module Data and Accessing Ports and Channels
Table 3-1. Equipment Configuration Window Field Descriptions (Continued)
Field Name
Field Value
Description
SW #
Default: N/A
Range: N/A
Format: Predefined
Displays the version of PSAX system software with
which the modules’ firmware was released. The software version is encoded in the module firmware.
Because not all modules require firmware upgrades
with every new PSAX system software release, the
software version that is displayed in this window may
be lower than the CPU system software that is currently running on the PSAX system. See the most
recent Release Note document for the latest software
and firmware lineup information.
PEC
Default: N/A
Range: N/A
Format: Predefined
Displays the product element code (PEC) used to identify and order this type of module. The PEC is encoded
in the module bootloader.
Serial #
Default: N/A
Range: N/A
Format: Predefined
Displays the unique serial number of the individual
module. The product serial number is encoded in the
module firmware. The format of this field is the following:
PSAX System Rel. 6.5.0 and later: 12-digit number in
the format: YYVVDDnnnnnn, where YY = year of manufacture VV = vendor ID code (manufacturer and location) DD = date code of manufacture (either month or
week depending on vendor’s preference) nnnnnn =
sequential number, which in conjunction with YY, VV,
and DD, creates a unique number for each hardware
component in the PSAX product line
For existing products with the 10-digit serial number
used in Rel. 6.5.0 or later systems, this number is displayed with two preceding zeros.
PSAX Rel. 6.3.0 and earlier: 10-digit number. For
products with 12-digit serial numbers used in Rel 6.3.0
or earlier systems, the first two digits (YY) are not displayed.
Alarm Status Values
The Alarm Status field on the Equipment Configuration window is described
in Table 3-2.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-6
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-2. Module Alarm Status Descriptions on the Equipment Configuration Window
Alarm Status
Module Type
Affected
Description
NoAlarm
I/O and Server Indicates that no alarms have been detected for the module
in this slot.
WrongCardType
I/O and Server Indicates that one type of module was configured in this
slot in the chassis, but a now different module occupies this
slot.
LineFailed
All
Hexadecimal format,
Example:
12345678ABC
I/O and Server Indicates that one or more ports on the module in this slot
currently have a loss of signal. The numbers indicate which
ports have a loss of signal. For modules that have more
than eight ports not receiving signals, the value in this field
is in hexadecimal format.
CardRemoved
All
Indicates that the module in this slot is no longer receiving
or transmitting signals because the line failed.
Indicates that one of the following events occurred:
• The module in this slot was configured and then
removed from the slot.
• Connections on the OC-3, OC-12, STM-1, or STM-4
APS/MSP primary module in this slot were transferred to
the standby module. After the transfer occurs, the former
primary module then displays CardRemoved in the
Alarm Status field; the former standby module then displays Primary in the Status field.
ReferenceClockFailed Stratum 3–4
Indicates that the timing reference clock on the Stratum
module in this slot failed.
CompositeClockFailed Stratum 3–4
Indicates that the timing composite clock on the Stratum
module in this slot failed.
Overload
Power Supply
Indicates that the Power Supply module is operating under
an overload condition.
PowerFailed
Power Supply
Indicates that the power has failed.
Minus48vFailed
Power Supply
Indicates that the -48 V dc Power Supply module output
failed.
UnknownAlarm
I/O and Server Indicates that the reason for failure is not known.
CompleteClockFailed Stratum 3–4
Indicates that the backplane detected a clock error.
PowerFailed
Indicates that no power is coming into the PSAX chassis.
Power Supply
Configuring the Module
The 21-Port High-Density E1 IMA module has 21 physical E1 ports that may
be used for native E1 ATM services or for E1 IMA groups. You must first
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-7
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
configure the 21-Port High-Density E1 IMA module before you can set up
connection provisioning.
The configuration of IMA groups on the 21-Port High-Density E1 IMA
module involves the following major tasks:
1. Each port must be configured with the IMA interface, and that IMA
interface must be brought into service.
2. Each IMA group must be established.
3. Each IMA group must be configured with an ATM interface (IISP, UNI,
or PNNI).
Configuring Ports and Channels
To configure the 21-Port High-Density E1 IMA ports and channels, perform
the following procedure.
Configuring the Ports and Channels
Begin
1 On the Console Interface Main Menu window (see Figure 3-6), select
the Equipment Configuration option and press Enter.
Figure 3-6.
Console Interface Main Menu Window (Equipment Configuration
Selected)
The Equipment Configuration window is displayed (see Figure 3-7 and
Figure 3-8) .
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-8
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Figure 3-7.
Equipment Configuration Window (As Displayed on the PSAX 1250,
PSAX 2300, and PSAX 4500 Console)
Figure 3-8.
Equipment Configuration Window (As Displayed on the PSAX 1000
Console)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-9
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
2 On the Equipment Configuration window, select an HD–E1–IMA
module in the Card Type column and press Enter. The 21-Port High
Density E1 IMA Module Configuration window is displayed (see
Figure 3-9).
Figure 3-9.
21-Port High Density E1 IMA Module Configuration Window
This window allows you to select a physical port (1–21) to configure or
the virtual port (22) to configure an IMA group (channel). It also
provides the operational status of the ports and channels.
Commands
The commands in this window have the following functions:
Command
Bring All Interfaces Into Service
Function
Brings the out-of-service configured interfaces for all the
ports to in-service status. The value InService is displayed in the Oper_Status field for all 21 ports.
Take All Interfaces Out Of Service Takes the in-service configured interfaces for all
ungrouped ports to out-of-service status. The value OutOfService is displayed in the Oper_Status field for all
ungrouped ports. You must use this command first
before using the Delete All Interfaces command.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-10
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Command
Function
Delete All Interfaces
Deletes the configured interfaces for all ungrouped ports.
The value Unconfigured is displayed in the Oper_Status
field for all ungrouped ports. Ports that were in groups
are no longer grouped but are still configured and in-service. You must first take all interfaces out of service
(using the Take All Interfaces Out Of Service command) before you can use this command to delete all the
configured interfaces. Use the Take All Interfaces Out
Of Service command and the Delete All Interfaces
command again to delete the remaining ungrouped
ports. The value Unconfigured is displayed in the
Oper_Status field for all 21 ports.
Update Display
Updates the values in the fields to show the most current
configuration. Use this command primarily to display the
most current information in the Oper_Status field.
Go Back to Equipment Configura- Redisplays the Equipment Configuration window.
tion
3 Select one of the lines with the physical port you want to configure and
press Enter. The 21-Port High Density E1 IMA Module Port and Channel
Configuration window is displayed (see Figure 3-10).
Figure 3-10. 21-Port High Density E1 IMA Module Port and Channel
Configuration Window
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-11
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Commands
The commands in this window have the following functions:
Command
Function
Apply Port Configuration
For a specified port number value, applies the port configuration field values you set.
Reset Port Display
Resets the port configuration fields to the last set of saved
values.
Bring Interface Into Service
Brings the selected interface in the Interface Type field for
the channel to in-service status. This field is displayed only
when the interface is out of service or unconfigured.
Take Interface Out Of Service Takes the in-service configured interface to out-of-service
status. This field is displayed only when the interface is in
service.
Configure Interface
Displays the screen through which you will configure the
applied ATM interface for this port.
View Port Statistics
Displays the High Density E1 IMA Port Statistics window.
Go Back to Card Configuration
Redisplays the High Density E1 IMA Card Configuration
window.
Field Descriptions
4 Select the values for the fields on this window from the values given in
Table 3-3.
Table 3-3. 21-Port High Density E1 IMA Module Port and Channel Configuration Window Field
Descriptions
Field Name
[Line Type]
[Line Coding]
Field Value
Description
Default: Crc-mf
Range: N/A
Format: Predefined
Indicates the framing mode for the port.
Crc-mf
Indicates that the non-selectable mode is CRC4CAS. The near-end port can receive traffic from
the far-end port in this mode or in CCS without
time slot 16.
Default: Hdb3
Range: N/A
Format: Predefined
Indicates the type of line coding to be used on
this port. (The data format that lets either end of
the communications channel correctly interpret
messages from the other.)
Hdb3
High-density bipolar of order 3. A bipolar coding
method that does not allow more than 3 consecutive zeros.
Ami
Alternate mark inversion. Indicates zero code
suppression.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-12
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-3. 21-Port High Density E1 IMA Module Port and Channel Configuration Window Field
Descriptions (Continued)
Field Name
Loopback
Transmit Clock
[Time Slot 16]
[Line Status]
Field Value
Description
Default: NoLoop
Range: N/A
Format: Predefined
Indicates whether the port is to be used for loopback testing and, if so, the type of loopback to be
performed.
NoLoop
The port will not be used for loopback.
LocalLoop
Local loopback will be used on this port. The signal will be received from another module in the
chassis, sent through the module circuitry
(including the segmentation and reassembly
(SAR) function) and the chassis backplane to the
originating module.
LineLoop
Line loop will be used on this port. The received
signal will be sent through the receiver and the
line driver, and then back out to the originating
point.
TestMode
Not supported.
Default: LocalTiming
Range: N/A
Format: Predefined
Indicates what type of synchronization is used by
the interface to maintain proper data flow
through the PSAX system and the remote devices
connected to the system.
LocalTiming
Selects a synchronization source (CompositeClock, T1BITS, E1ETSI, CompositeClockDS0A,
Freerun, or LineTiming) that is provided through
the Stratum 3–4 module.
LoopTiming
Selects the recovered clock from the received
data and is used as the transmit clock on the
selected interface.
Adaptive Timing
Selects an interface buffer to allow different data
rates to pass through the PSAX system and prevent overruns or underruns in the traffic. This
option is displayed when the port is configured as
Unstructured in the Data Transfer Type field.
Default: Cas
Range: N/A
Format: Predefined
Indicates that Time Slot 16 is reserved for network use and not available for ATM payload.
Cas
Indicates that Time Slot 16 is reserved for network use.
Default: NoAlarm
Range: N/A
Format: Predefined
Indicates the line status of the port: loopback,
failure, received and transmitted alarm information. See the table below for descriptions.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-13
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-3. 21-Port High Density E1 IMA Module Port and Channel Configuration Window Field
Descriptions (Continued)
Field Name
Interface Type
[Admin Status]
Field Value
Description
Default: Unconfigured
Range: N/A
Format: Predefined
Indicates the type of end-to-end connection protocol that governs the transmission parameters of
this configured port and channel interface.
Unconfigured
This interface is not configured.
Atm Ima
This interface is configured as an ATM IMA interface.
Note: Each port in an IMA group must first be
configured as an IMA interface.
AtmUni3-0
This interface is configured for the ATM UNI 3.0
interface.
AtmUni3-1
This interface is configured for the ATM UNI 3.1
interface.
AtmUni4-0
This interface is configured for the ATM UNI 4.0
interface.
AtmPnni1_0
This interface is configured for the ATM PNNI 1.0
interface.
IispUser
This interface is configured for the ATM IISP user
interface.
IispNetwork
This interface is configured for the ATM IISP network interface.
Default: Unconfigured
Range: N/A
Format: Predefined
Indicates the administrative status of the port.
Unconfigured
The interface for the port is not configured.
OutOfService
The interface has not yet been brought into service, or in-service interface has been set to out of
service with the Take Interface Out of Service
command.
InService
The interface has been brought into service with
the Bring Interface Into Service command.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-14
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-3. 21-Port High Density E1 IMA Module Port and Channel Configuration Window Field
Descriptions (Continued)
Field Name
[Oper Status]
Field Value
Description
Default: Unconfigured
Range: N/A
Format: Predefined
Indicates the operational status of the port and
whether the port is exchanging a valid signal.
Unconfigured
This channel is not operational because the interface is not configured.
OutOfService
Two types of problems cause this status.
• A loss-of-signal condition is due to any one of
the following:
~ The module port is not physically
connected to a cable.
~ The cable is not connected at the other end
to a device.
~ The cable is broken.
• A loss of frame or encoding is due to a problem
with the framing or encoding of the signal. For
example, a repeater could corrupt the signal.
InService
The port is physically connected to a cable, the
cable is conducting the signal, and the signal is
being transmitted and received correctly.
Table 3-4 provides the line status alarm descriptions for the 21-Port HighDensity E1 IMA module. This alarm is displayed in the Line Status field on
the High Density E1 IMA Port and Channel Configuration window.
Table 3-4. 21-Port High-Density E1 IMA Module—Line Status Alarm Descriptions
Alarm
Description
NoAlarm
No alarm is present.
RcvFarEndLOF
Far-end sending loss of frame.
FarEndLOF
Near-end sending loss of frame indication.
RcvAIS
Far-end sending alarm indication signal.
AIS
Near-end sending alarm indication signal.
LossOfFrame
Near-end loss of frame.
LossOfSignal
Near-end loss of signal.
LoopbackState
Near-end is looped.
T16AIS
Near-end sending E1 TS16 alarm indication signal.
RcvFarEndLOMF
Far-end sending TS16 loss of multi-frame.
FarEndLOMF
Near-end sending TS16 loss of multi-frame.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-15
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-4. 21-Port High-Density E1 IMA Module—Line Status Alarm Descriptions
Alarm
Description
RcvTestCode
Near-end detects a test code.
OtherFailure
Any line status not defined here.
RmtLoopback
Far-end loopback.
5 To apply the values for the port fields, select the Apply Port
Configuration command.
6 Select the Configure Interface command.
The selected interface configuration window is displayed. See the
PacketStar&reg; PSAX Connections Provisioning Guide for instructions.
7 To bring the interface into service, select the Bring Interface Into
Service command.
Note:
You must bring the ATM IMA interface into service before you
can set up High-Density E1 IMA groups.
End
Viewing Port Statistics
Begin
To view statistics for a port, from the 21-Port High Density E1 IMA Module
Port and Channel Configuration window (Figure 3-10), select the View Port
Statistics command. The 21-Port High Density E1 IMA Port Statistics
window (see Figure 3-11) is displayed.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-16
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Figure 3-11. 21-Port High Density E1 IMA Port Statistics Window
Commands
The commands in this window have the following functions:
Command
Function
Continuous Update
Updates the values in the fields every second.
Reset Statistics
Sets all field values to zero.
Go Back to Port Configuration
Redisplays the High Density E1 IMA Port and
Channel Configuration window.
Field Descriptions
Descriptions of the data fields for the High Density E1 IMA Port Statistics
window are given in Table 3-5.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-17
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-5. 21-Port High Density E1 IMA Port Statistics Window Field Descriptions
Field Name
Field Value
Description
Errored Seconds
Default: 0000000000 A count of the number of errored seconds that
have occurred on the E1 port since the last time
Range: N/A
statistics were reset. An errored second contains
Format: Numeric
at least one of the following:
• Path coding violations
• Controlled slip events
• A detected alarm indication signal (AIS) defect
• Presence of bipolar violations
Severely Errored
Seconds
Default: 0000000000 A count of the number of severely errored seconds that have occurred on the E1 port since the
Range: N/A
last time statistics were reset. A severely errored
Format: Numeric
second contains at least one of the following:
• 320 or more path coding violation error events
• Out-of-frame (OOF) defects
• Detected AIS defect
• A minimum of 1,544 line coding violations
(LCVs).
Severely Errored
Framing Seconds
Default: 0000000000 A count of the number of severely errored framing seconds encountered by the E1 port in one of
Range: N/A
the previous 96 individual 15-minute intervals. A
Format: Numeric
severely errored framing second has one or more
out-of-frame defects or a detected AIS defect.
Unavailable Seconds
Default: 0000000000 A count of the number of unavailable seconds
encountered by the E1 port in one of the previRange: N/A
ous 96 individual 15-minute intervals. UnavailFormat: Numeric
able seconds (UAS) are calculated by the number
of seconds that the interface is unavailable.
Controlled Slip Sec- Default: 0000000000 A count of the number of controlled slip seconds
onds
encountered by the E1 port in the previous
Range: N/A
24-hour period. A controlled slip second is a
Format: Numeric
1-second interval containing one or more controlled slip events.
Path Coding Violations
Default: 0000000000 A count of the number of path coding violations
encountered by the E1 port in the previous
Range: N/A
24-hour period. A path coding violation is a
Format: Numeric
frame synchronization bit error in the
E1-no-CRC formats, or a CRC error in the
E1-CRC formats.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-18
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-5. 21-Port High Density E1 IMA Port Statistics Window Field Descriptions
Field Name
Line Errored Seconds
Field Value
Description
Default: 0000000000 A count of the number of line errored seconds
encountered by the E1 port in the previous
Range: N/A
24-hour period. A line errored second is a second
Format: Numeric
in which one or more line code violation error
events were detected.
Bursty Errored Sec- Default: 0000000000 A count of the number of bursty errored seconds
onds
encountered by the E1 port in the previous
Range: N/A
24-hour period. A bursty errored second has
Format: Numeric
fewer than 320 and more than 1 path coding violation error events, no severely errored frame
defects, and no detected incoming AIS defects.
Line Coding Violations
Default: 0000000000 A count of the number of line coding violations
that have occurred on the E1 port since the last
Range: N/A
time statistics were reset. Line coding violations
Format: Numeric
indicate that a bipolar violation or an excessive
zeroes error event has occurred.
Configuring IMA Groups
Once you have configured ports with ATM IMA interfaces, you can set up
High-Density E1 IMA groups for the 21-Port High-Density E1 IMA module.
High-Density E1 IMA groups must be defined on the virtual port (port 22).
Up to 10 groups (channels) can be configured on this port. A group may have
1 to 21 of the physical ports assigned to it. For example:
~ You can assign all 21 of the physical ports to Group 1 (channel 1);
however 9 groups would be unused.
~ You can assign one physical port to Group 1(channel 1) and any
combination in Group 2 (channel 2) through Group 10 (channel 10)
totalling 10 groups and 21 ports.
Figure 3-12 illustrates these options.
1
21
Physical
Ports
Groups
1
2
3
4
5
6
7
8
9
10
Channels
Virtual Port 22
1-21 physical ports can be assigned to any one group (channel) or in any
combination totalling 10 groups and 21 ports.
Figure 3-12. High-Density E1 IMA Group Configuration Options
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-19
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Perform the following procedure to set up High-Density E1 IMA groups.
Setting Up High-Density E1 IMA Groups
Begin
1 On the 21-Port High Density E1 IMA Module Configuration window
(see Figure 3-9), select port 22, which is the virtual port, and press
Enter. The IMA Virtual Group Channel Configuration window is
displayed (see Figure 3-13).
Figure 3-13. IMA Virtual Group Channel Configuration Window
Commands
The commands in this window have the following functions:
Command
Function
Bring Interfaces Into Service
Brings out-of-service configured interfaces to in-service status. You must first configure the interface
before you can use this command.
Take Interfaces Out of Service
Takes the in-service configured interfaces to out-ofservice status. You must use this command first
before using the Delete All Interfaces command.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-20
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Command
Function
Delete All Interfaces
Deletes all interfaces for all ports. The value Unconfigured is displayed in the Interface, Admin. Status,
and Oper. Status fields for all groups. All values are
cleared in the Ports field. Only the interfaces that are
out of service can be unconfigured by this command.
Go Back to Card Config
Redisplays the 21-Port High Density E1 IMA Module
Configuration window.
Field Descriptions
The display-only fields in this window are described in Table 3-6.
Table 3-6. IMA Virtual Group Channel Configuration Window Field Descriptions
Field Name
Interface
(display only)
Admin. Status
(display only)
Field Value
Description
Default: Unconfigured
Range: N/A
Format: Predefined
Displays the ATM interface type applied to the
group (1-10). The interface type is applied in the
next window, IMA Group Configuration.
Unconfigured
Indicates that this interface is not configured.
AtmUni 3-0
Indicates that this interface is configured for ATM
UNI 3.0 interface.
AtmUni 3-1
Indicates that this interface is configured for ATM
UNI 3.1 interface.
AtmUni 4-0
Indicates that this interface is configured for ATM
UNI 4.0 interface.
IispUser
Indicates that this interface is configured for ATM
IISP User interface.
IispNetwork
Indicates that this interface is configured for ATM
IISP Network interface.
AtmPnni 1-0
Indicates that this interface is configured for ATM
ATM PNNI 1.0 interface.
Default: Unconfigured
Range: N/A
Format: Predefined
Displays the administrative status of the group
(1-10).
Unconfigured
Indicates that the interface for the group is not
configured.
OutOfService
Indicates that the interface has not yet been
brought into service, or its in-service interface has
been set to out of service with the Take Interfaces Out of Service command
InService
The interface has been brought into service with
the Bring Interfaces Into Service command.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-21
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-6. IMA Virtual Group Channel Configuration Window Field Descriptions (Continued)
Field Name
Oper. Status
(display only)
Ports
(display only)
Field Value
Description
Default: Unconfigured
Range: N/A
Format: Predefined
Displays the operational status of the group and
whether the group is exchanging a valid signal.
Unconfigured
Indicates that this channel is not operational
because the interface is not configured.
OutOfService
Indicates that the group (near end and far end) is
not operational because there is no connection.
InService
Indicates that the group (near end and far end) is
operational.
Default: N/A
Range: 1-21
Format: Numeric
Displays each port assigned to the group. Ports
are assigned on the next window, IMA Group
Configuration.
2 Select the first line for group 1 and press Enter. The IMA Group
Configuration window (see Figure 3-14) is displayed.
Figure 3-14. IMA Group Configuration Window
Commands
The commands in this window have the following functions:
Command
Function
Apply IMA Group Configuration Applies the configuration field values you set.
Reset IMA Group Display
Resets the port configuration display.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-22
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Command
Function
Bring Interface Into Service
Brings the out-of-service configured interface for the
channel to in-service administrative status. You must
first configure the interface before you can use this
command. This command is displayed only when the
interface is out of service.
Take Interface Out Of Service
Takes the in-service configured interface to out-ofservice administrative status. You must use this command first before using the Delete All Interfaces
command. This command is displayed only when the
interface is in service.
Configure Interface
Displays the screen through which you will configure
the applied ATM interface for this group.
View IMA Group Statistics
Displays the IMA Group Channel Statistics window.
Go Back to Channel Config
Redisplays the IMA Virtual Group Channel Configuration window.
Field Descriptions
3 Select the values for the fields on this window from the values given in
Table 3-7.
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
Field Value
Description
Minimum Tx Links Default: 1
Range: 1–21
Format: Numeric
Indicates the minimum number of transmit links
required to be active for the IMA group to be in
the up state.
Minimum Rx Links Default: 1
Range: 1–21
Format: Numeric
Indicates the minimum number of receive links
required to be active for the IMA group to be in
the up state.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-23
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
Near-end Tx Clock
Field Value
Description
Default: Ctc
Range: N/A
Format: Predefined
Indicates the transmit clocking mode used by the
near-end IMA group.
Ctc
Specifies that the Common Transmit Clock (CTC)
mode will be used by the near-end IMA group.
Select this value only if the transmit clock of all
IMA links in this group will be derived from the
same source. You must set up the underlying
clock configuration to ensure operation in the
selected mode.
Itc
Specifies that the Independent Transmit Clock
(ITC) mode will be used by the near-end IMA
group. Select this value only if there will be at
least one IMA link in this group whose transmit
clock will be derived from a source that is different from at least one other link transmit clock.
The ITC mode allows links to have different clock
sources but does not require it.
Tx IMA Id
Default: N/A
Range: 0–255
Format: Numeric
Indicates the IMA identifier to be used by the farend IMA function. The Tx IMA Id is an identifier
used to distinguish this IMA group from other
IMA groups in a connection. Choose a unique
value within the range of 0–255; it does not have
to be the same as that of the far-end IMA group.
Tx Frame Length
Default: M128
Range: N/A
Format: Predefined
Indicates the frame length to be used by the IMA
group in the transmit direction. This can be set
only when the IMA group is configured. The
frame length is the number of cells in each IMA
frame. Use the smaller number (e.g. m32) to send
more IMA frames and use the larger number (e.g.
m256) to send fewer IMA frames. Smaller frames
handle errors more quickly, but the larger frames
result in less overhead.
M32
The frame length is M32 cells.
M64
The frame length is M64 cells.
M128
The frame length is M128 cells.
M256
The frame length is M256 cells.
Default: 25
Range: 1-200
Format: Numeric
Indicates the maximum number of milliseconds
of delay differential among the links that will be
tolerated.
Link Delay Diff
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-24
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
Field Value
Compatibility Mode Default: No
Range: N/A
Format: Predefined
Auto IMAversion
Detection
Preferred
IMAversion
Description
Allows the near-end IMA group to receive the
link status at the correct location in the IMA control protocol (ICP) cell from the far-end IMA
group. This mode must be set correctly when
connected to ATM IMA Specification Version 1.0
equipment. The Compatibility Mode field must
be enabled when connected to equipment following the alternate link state reporting mechanism described in Appendix C.8.1 of ATM IMA
Specification Version 1.1.
No
Disables the Compatibility Mode.
Yes
Enables the Compatibility Mode.
Default: Enabled
Range: N/A
Format: Predefined
Indicates whether the IMA group will automatically select the compatible ATM IMA Specification (Version 1.0 or Version 1.1) for both ends of
a link or only use the configured preferred ATM
IMA Specification version.
Enabled
Indicates that the IMA group will automatically
select the compatible ATM IMA Specification version for both ends of a link.
Disabled
Indicates that the IMA group will only use the
configured preferred ATM IMA Specification version in the Preferred IMAversion field.
Default: Version1p1 Displays the preferred ATM IMA Specification
version.
Range: N/A
Format: Predefined
Version1p1
Indicates that the preferred ATM IMA Specification is Version 1.1.
Version1p0
Indicates that the preferred ATM IMA Specification is Version 1.0.
Alpha Value
Default: 2
Range: 1-2
Format: Numeric
Indicates the alpha value used to specify the
number of consecutive invalid IMA control protocol (ICP) cells to be detected before moving to
the IMA HUNT state. The smaller the value, the
faster the IMA link will go into a loss of IMA
frame (LIF) failure state.
Beta Value
Default: 2
Range: 1-5
Format: Numeric
Indicates the beta value used to specify the number of consecutive errored ICP cells to be detected
before moving to the IMA HUNT state. The
smaller the value, the faster the IMA link will go
into an LIF failure state.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-25
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
Gamma Value
Field Value
Default: 1
Range: 1-5
Format: Numeric
[Far-end Tx Clock] Default: Ctc
Range: N/A
Format: Predefined
[Rx IMA ID]
Description
Indicates the gamma value used to specify the
number of consecutive valid ICP cells to be
detected before moving from the IMA PRESYNC
state to the IMA SYNC state. The smaller the
value, the faster the IMA link will recover from
an LIF error.
Displays the transmit clocking mode used by the
far-end IMA group.
Ctc
Specifies that the Common Transmit Clock (CTC)
mode will be used by the far-end IMA group.
Itc
Specifies that the Independent Transmit Clock
(ITC) mode will be used by the far-end IMA
group.
Default: 0
Range: 0-255
Format: Numeric
Displays the IMA identifier currently in use by
the far-end IMA function. The Rx IMA Id is an
identifier used to distinguish this IMA group from
other IMA groups in a connection.
[Rx Frame Length] Default: M32
Range: N/A
Format: Predefined
Displays the IMA frame length in cells as received
from the remote IMA function.
M32
The frame length is M32 cells.
M64
The frame length is M64 cells.
M128
The frame length is M128 cells.
M256
The frame length is M256 cells.
[Least Delay Link]
Default: Port 0
Range: 0-21
Format: Numeric
Displays the interface index of the link configured in the IMA group that has the smallest link
propagation delay. This value has meaning only if
more than one link has been configured in the
IMA group.
[Max Delay Diff]
Default: 1
Range: N/A
Format: Numeric
Displays the observed number of milliseconds of
delay differential among the links.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-26
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
Interface Type
[Admin Status]
[Oper Status]
Field Value
Description
Default: Unconfigured
Range: N/A
Format: Predefined
Indicates the type of end-to-end connection protocol that governs the transmission parameters of
the configured channel interface. An interface
type can be configured only if a port exists in the
group.
Unconfigured
This interface is not configured.
AtmUni3-0
This interface is configured for the ATM UNI 3.0
interface.
AtmUni3-1
This interface is configured for the ATM UNI 3.1
interface.
AtmUni4-0
This interface is configured for the ATM UNI 4.0
interface.
IispUser
This interface is configured for the ATM IISP user
interface.
IispNetwork
This interface is configured for the ATM IISP network interface.
AtmPnni1-0
This interface is configured for the ATM PNNI 1.0
interface.
Default: Unconfigured
Range: N/A
Format: Predefined
Displays the administrative status of the port.
Unconfigured
The interface for the port is not configured.
OutOfService
The interface has not yet been brought into service, or its in-service interface has been set to out
of service with the Take Interface Out of Service command.
InService
The interface has been brought into service with
the Bring Interface Into Service command.
Default: Unconfigured
Range: N/A
Format: Predefined
Displays the operational status of the port and
whether the port is exchanging a valid signal.
Unconfigured
This channel is not operational because the interface is not configured.
OutOfService
The group (near end and far end) is not operational because there is no connection.
InService
The group (near end and far end) is operational.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-27
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
[Near-end State]
Field Value
Description
Default: NotConfig- Displays the current operational state of the nearured
end IMA group state machine.
Range: N/A
Format: Predefined
NotConfigured
The group does not exist.
StartUp
The near end is in start-up and is waiting to
receive the indication that the far end is in startup.
StartUpAck
When both groups start up, they move through
this transitional state to the InsufficientLinks
state. While in this state, indications from the
near end that it is in start-up are ignored.
CfgAbt
Configuration aborted. This state is entered when
the near end tries to use the following unacceptable configuration parameters (remaining fields
below).
UnsupportedM
Unsupported value of M (M = frame length).
CfgAbtIncSymmetry
Incompatible group symmetry.
CfgAbtOther
Configuration aborted for other reasons.
InsufficientLinks
This state implies that the group has accepted the
near-end group parameters and that the near end
has also accepted its own group parameters, but
does not have sufficient links to move into the
Operational state.
Blocked
The group is blocked (e.g., inhibited by Unit
Management (UM)). The group can be blocked
for maintenance purposes while sufficient links
are Active in both directions. The PSAX group is
blocked when it is administratively out of service.
Operational
The group is operational and in the Up state. The
group is not inhibited and has sufficient links in
both the Tx and Rx directions. The IMA interface
now has the capability to receive ATM layer cells
and pass them from the IMA sublayer to the ATM
layer.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-28
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
[Far-end State]
Field Value
Description
Default: NotConfig- Displays the current operational state of the farured
end IMA group state machine.
Range: N/A
Format: Predefined
NotConfigured
The group does not exist.
StartUp
The far end is in start-up and is waiting to receive
the indication that the near end is in start-up.
StartUpAck
When both groups start up, they move through
this transitional state to the InsufficientLinks
state. While in this state, indications from the
near end that it is in start-up are ignored.
CfgAbt
Configuration aborted. This state is entered when
the far end tries to use the following unacceptable configuration parameters (remaining fields
below).
UnsupportedM
Unsupported value of M (M = frame length).
CfgAbtIncSymmetry
Incompatible group symmetry.
CfgAbtOther
Configuration aborted for other reasons.
InsufficientLinks
This state implies that the group has accepted the
far-end group parameters and that the far end
has also accepted its own group parameters, but
does not have sufficient links to move into the
Operational state.
Blocked
The group is blocked (e.g., inhibited by the Unit
Management (UM)). The group can be blocked
for maintenance purposes while sufficient links
are Active in both directions.
Operational
The group is operational and in the Up state. The
group is not inhibited and has sufficient links in
both the Tx and Rx directions. The IMA interface
now has the capability to receive ATM layer cells
and pass them from the IMA sublayer to the ATM
layer.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-29
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
[Failure Status]
Field Value
Description
Default: NoFailure
Range: N/A
Format: Predefined
Displays the current failure status of the IMA
group, which gives the reason why the group
state machine is in the Down state. This means
that either the near end or the far end is not
operational. See the Near-end State and Far-end
State field values above.
NoFailure
The IMA group state machine is Up and in the
Operational state.
StartUpNe
The near end is in the StartUp state.
StartUpFe
The far end is in the StartUp state.
InvalidMValueNe
The near end has received an invalid M value
(M = frame length).
InvalidMValueFe
The far end has received an invalid M value
(M = frame length).
FailedAsymmetricNe
The near end is reporting that the far end is
requesting a group symmetry that the near end
does not support.
FailedAsymmetricFe
The far end is not accepting near-end symmetry.
InsuffLinksNe
The near end does not have sufficient links to
move into the Operational state.
InsuffLinksFe
The far end does not have sufficient links to move
into the Operational state.
BlockedNe
The group is blocked at the near end.
BlockedFe
The group is blocked at the far end.
OtherFailure
The group has failed for other reasons.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-30
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Table 3-7. IMA Group Configuration Window Field Descriptions
Field Name
[GroupSymmetry]
In.
Av.
Field Value
Description
Default: SymOpera- Displays the mode that allows symmetric or
tion
asymmetric cell rate transfer over the IMA virtual
link.
Range: N/A/
Format: Predefined
SymOperation
The IMA group is only required to carry ATM
layer cells on physical links in which the IMA
links in both the transmit and receive directions
are Active.
AsymOperation
The IMA group is allowed to carry ATM traffic
over the physical links on which the IMA links in
both the transmit and receive directions are not
Active at the same time.
AsymConfiguration
The IMA group is not required to configure IMA
links in both directions of the physical links used
by the IMA unit.
Default: 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
16 17 18 19 20
Range: 1–21
Format: Numeric
Displays the ports that are available (in this case,
the first 20 of 21) to be included in a group. To
select a port, navigate to a number in the lower,
Av. (available) row and press Enter. The number
moves to the upper, In. (in group) row. To select
more ports, use the &gt;&gt; navigation key to go to
the next page and the &lt;&lt; navigation key to go to
the previous page.You may select 1 to 21 ports to
make a group.
4
Select the Apply IMA Group Configuration command. The port
configuration is applied.
5 Select the Configure Interface command. The selected interface type
window is displayed. See the PacketStar&reg; PSAX Connections Provisioning
Guide for instructions.
6 Select the Bring Interface Into Service command. The selected
interface is administratively in service. The [Admin Status] field displays
the InService value.
7 Repeat steps 1–6 under ”Setting Up High-Density E1 IMA Groups” on
page 3-20 for the remaining nine IMA groups, as needed. All 21
physical ports may belong to one group.
End
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-31
Chapter 3 Configuring Ports and Channels Using the Console
Configuring the Module
Viewing Group Channel Statistics
Begin
To view statistics for a group, from the IMA Group Configuration window
(Figure 3-14), select the View IMA Group Statistics command. The IMA
Group Channel Statistics window (see Figure 3-15) is displayed.
Figure 3-15. IMA Group Channel Statistics Window
Commands
The commands in this window have the following functions:
Command
Function
Continuous Update
Updates the field values every second.
Reset Statistics
Sets all field values to zero.
Go Back to Group Channel
Configuration
Redisplays the IMA Group Configuration window.
Field Descriptions
Descriptions of the data fields for this window are given in Table 3-8.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-32
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Saving the Equipment Configuration and Logging Off
Table 3-8. IMA Group Channel Statistics Window Field Descriptions
Field Name
Field Value
Description
[Near-End Failures] Default: 0
Range: N/A
Format: Numeric
Displays the number of failures at the transmitting end of the link.
[Far-End Failures]
Default: 0
Range: N/A
Format: Numeric
Displays the number of failures at the receiving
end of the link.
[Number of Active
Tx Links]
Default: 0
Range: 0–21
Format: Numeric
Displays the number of active transmit links from
the near end.
[Number of Active
Rx Link]
Default: 0
Range: 0–21
Format: Numeric
Displays the number of active receive links from
the far end.
[Time Elapsed]
Default: 0:00:00
Range: N/A
Format: hh:mm:ss
Displays the time elapsed in hours, minutes, and
seconds since last reset.
Saving the Equipment Configuration and Logging Off
After configuring the module ports and channels, the interface types for each
port and channel, and the connections, you must save the values to the
PSAX system database. It is recommended that you save your values
frequently as you progress through your work, at a minimum, after finishing
each stage of work:
•
Configuring each module in your system
•
Configuring the connections in your system
•
Before exiting your current console session
Perform the following procedure to permanently save the values for your
system.
! CAUTION:
If your system loses power or if you reboot the chassis, and you have not
yet saved the values permanently, you will lose all unsaved values you
have applied on the various windows.
Begin
1 Press Ctrl+G, to return to the Console Interface Main Menu window.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-33
Chapter 3 Configuring Ports and Channels Using the Console
Saving the Equipment Configuration and Logging Off
On the Console Interface Main Menu window, [Modified] is displayed
next to the Save Configuration command, indicating you have made
changes to the system that are not yet saved to the PSAX system database
(see Figure 3-16).
Figure 3-16. Save Configuration [Modified] (Before Saving)
2 Select the Save Configuration command or press Ctrl+A.
Wait a few seconds while the system writes the values to the PSAX system database. The system displays the following message while it is executing this command:
Saving the equipment and connection information
Note:
In PSAX systems with redundant CPUn modules, the standby
CPUn module reboots every time you save the configuration on
the primary CPUn module. This event is a function of the SVC
retention feature and the result of saving the configuration
changes you have made.
When the save configuration function is completed, the system displays
an appropriate message as described in Table 3-9.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-34
Release 10.0.0
255-700-584
Chapter 3 Configuring Ports and Channels Using the Console
Provisioning Connections
Table 3-9. Messages Generated after the Save Configuration Process
When a PSAX
system is...
the system displays...
nonredundant
T-SaveConfiguration: saveConfigurationReasonCode=All-OK
redundant
T-SaveConfiguration: saveConfigurationReasonCode =
Expect2ndCPUCardFailedOrRemoved*
The standby CPUn module is rebooted when the save command is issued.
After the standby CPUn module reboots, the system displays the following
message: T-SaveConfiguration: saveConfigurationReasonCode=FileTransferCompleted
*
This message indicates that while the standby CPUn module reboots after you select the Save
ration command, the standby CPUn module is temporarily unavailable.
Configu-
After saving the configuration values, the indicator [Modified] is no
longer displayed next to the Save Configuration command.
End
Provisioning Connections
For instructions on configuring interfaces and provisioning connections, see
your PacketStar&reg; PSAX Connections Provisioning Guide. In using that guide, keep
in mind that the following connection types are supported by the 21-Port
High-Density E1 IMA module:
•
PVC connections:
~ ATM-to-ATM virtual channel connection (VCC)
~ ATM-to-ATM virtual path connection (VPC)
~ Bridge-to-ATM virtual channel connection (VCC) (z)
~ Circuit Emulation-to ATM virtual channel connection (VCC)
~ Variable bit rate (VBR)-to-ATM virtual channel connection (VCC)
~ AAL2 Trunk Connection (w)
•
SVC connections:
~ ATM-to-ATM virtual channel connection VCC (n)
~ ATM IISP CBR connection
~ ATM IISP VBR connection
•
SPVC connections:
~ ATM-to-ATM virtual channel connection (VCC) (z)
~ Circuit Emulation-to-ATM virtual channel connection (VCC) (y)
~ Circuit Emulation-to-ATM Std AAL2 virtual channel connection
(VCC)
~ Variable bit rate (VBR)-to-ATM virtual channel connection (VCC) (w)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
3-35
Chapter 3 Configuring Ports and Channels Using the Console
Provisioning Connections
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
3-36
Release 10.0.0
255-700-584
A
Pin Configurations
Overview of This Appendix
This appendix describes the connector pin assignments for the 21-Port
High-Density E1 IMA module.
Connector Pin Assignments
The 21-Port High-Density E1 IMA module provides two 50-pin Mini-Champ
connectors(see Figure A-1) labeled PORTS 1-12 and PORTS 13-21. The following sections show the pin assignments between these connectors, the Lucent
cable, and the patch panel connectors.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Figure A-1. Pin Locations on the Mini-Champ Connector
To the PSAX 12-Port BNC Patch Panel
Table A-1 lists the pin assignments between the 21-Port High-Density E1
IMA module connectors, the Lucent cable, and the 50-pin RJ-48H connector
and the BNC connectors on the PSAX 12-Port BNC Patch Panel.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
A-1
Appendix A Pin Configurations
Connector Pin Assignments
Table A-1. 21-Port High-Density E1 IMA Module Connector, Cable, and PSAX 12-Port BNC Patch Panel
Pin Assignments
Module Connectors1
Port2
1/13
2/14
3/15
4/16
5/17
6/18
7/19
8/20
Signal Name Socket Pin #3
Lucent Cable
(COMCODE 300550639)
Mini Champ
RJ-48H
Plug P1
Socket P2
TX-T
27
27
26
2
TX-R
2
2
1
27
RX-T
1
1
39
1
RX-R
26
26
14
26
TX-T
29
29
27
4
TX-R
4
4
2
29
RX-T
3
3
40
3
RX-R
28
28
15
28
TX-T
31
31
28
6
TX-R
6
6
3
31
RX-T
5
5
41
5
RX-R
30
30
16
30
TX-T
33
33
29
8
TX-R
8
8
4
33
RX-T
7
7
42
7
RX-R
32
32
17
32
TX-T
35
35
30
10
TX-R
10
10
5
35
RX-T
9
9
43
9
RX-R
34
34
18
34
TX-T
37
37
31
12
TX-R
12
12
6
37
RX-T
11
11
44
11
RX-R
36
36
19
36
TX-T
40
40
32
15
TX-R
15
15
7
40
RX-T
14
14
45
14
RX-R
39
39
20
39
TX-T
42
42
33
17
TX-R
17
17
8
42
RX-T
16
16
46
16
RX-R
41
41
21
41
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
A-2
PSAX 12-Port BNC Patch
Panel
RJ-48H Plug BNC ConnecPin #
tor
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
Release 10.0.0
255-700-584
Appendix A Pin Configurations
Connector Pin Assignments
Table A-1. 21-Port High-Density E1 IMA Module Connector, Cable, and PSAX 12-Port BNC Patch Panel
Pin Assignments (Continued)
Module Connectors1
Port2
Signal Name Socket Pin #3
9/21
10/NC
4
11/NC
12/NC
Lucent Cable
(COMCODE 300550639)
Mini Champ
RJ-48H
Plug P1
Socket P2
PSAX 12-Port BNC Patch
Panel
RJ-48H Plug BNC ConnecPin #
tor
TX-T
44
44
34
19
TX-R
19
19
9
44
RX-T
18
18
47
18
RX-R
43
43
22
43
TX-T
46
46
35
21
TX-R
21
21
10
46
RX-T
20
20
48
20
RX-R
45
45
23
45
TX-T
48
48
36
23
TX-R
23
23
11
48
RX-T
22
22
49
22
RX-R
47
47
24
47
TX-T
50
50
37
25
TX-R
25
25
12
50
RX-T
24
24
50
24
RX-R
49
49
25
49
TX1
RX1
TX1
RX1
TX1
RX1
TX1
RX1
1 For 21-port E1 modules, one module requires two PSAX 12-Port BNC Patch Panels.
2 Indicates port numbers from the module connectors and through the patch panel.
3 Pins 13 and 38 are not used by the module. On the patch panel, the RJ-48H connector is labeled PORT
and match with the BNC connectors labeled 1–12.
1–12,
4 NC = not connected at the module.
To the PSAX 24-Port RJ Patch Panel
Table A-1 lists the pin assignments between the 21-Port High-Density E1
IMA module connectors, the Lucent cable, and the PSAX 24-Port RJ Patch
Panel connectors, two 50-pin Cinch plugs and the 24 RJ-48C sockets.
Note:
The transmit and receive—tip and ring—pairs of the patch panel
RJ-48C sockets are reversed from the standard RJ-48C pin
assignments described in the ANSI T1.403 standard (Pin 1 R1, Pin
2 T1, Pin 4 R, and Pin 5 T).
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
A-3
Appendix A Pin Configurations
Connector Pin Assignments
Table A-1. 21-Port High-Density E1 IMA Module Module Connector, Cable, and PSAX 24-Port RJ Patch
Panel Pin Assignments
Lucent Cable
(COMCODE 300550639)
Module Connectors1
Port2
1/13
2/14
3/15
4/16
5/17
6/18
7/19
8/20
Signal Name Socket Pin #3
Mini Champ
Plug P1
RJ-48H
Socket P2
RX-T
1
1
39
39
1 (T1)
RX-R
26
26
14
14
2 (R1)
TX-T
27
27
26
26
4 (T)
TX-R
2
2
1
1
5 (R)
RX-T
3
3
40
40
1 (T1)
RX-R
28
28
15
15
2 (R1)
TX-T
29
29
27
27
4 (T)
TX-R
4
4
2
2
5 (R)
RX-T
5
5
41
41
1 (T1)
RX-R
30
30
16
16
2 (R1)
TX-T
31
31
28
28
4 (T)
TX-R
6
6
3
3
5 (R)
RX-T
7
7
42
42
1 (T1)
RX-R
32
32
17
17
2 (R1)
TX-T
33
33
29
29
4 (T)
TX-R
8
8
4
4
5 (R)
RX-T
9
9
43
43
1 (T1)
RX-R
34
34
18
18
2 (R1)
TX-T
35
35
30
30
4 (T)
TX-R
10
10
5
5
5 (R)
RX-T
11
11
44
44
1 (T1)
RX-R
36
36
19
19
2 (R1)
TX-T
37
37
31
31
4 (T)
TX-R
12
12
6
6
5 (R)
RX-T
14
14
45
45
1 (T1)
RX-R
39
39
20
20
2 (R1)
TX-T
40
40
32
32
4 (T)
TX-R
15
15
7
7
5 (R)
RX-T
16
16
46
46
1 (T1)
RX-R
41
41
21
21
2 (R1)
TX-T
42
42
33
33
4 (T)
TX-R
17
17
8
8
5 (R)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
A-4
PSAX 24-Port RJ Patch
Panel
RJ-48C
Cinch Plug Socket Pin #
Pin #
(CPE)
Release 10.0.0
255-700-584
Appendix A Pin Configurations
Connector Pin Assignments
Table A-1. 21-Port High-Density E1 IMA Module Module Connector, Cable, and PSAX 24-Port RJ Patch
Panel Pin Assignments (Continued)
Lucent Cable
(COMCODE 300550639)
Module Connectors1
Port2
9/21
10/22
11/23
12/24
Signal Name Socket Pin #3
Mini Champ
Plug P1
RJ-48H
Socket P2
PSAX 24-Port RJ Patch
Panel
RJ-48C
Cinch Plug Socket Pin #
(CPE)
Pin #
RX-T
18
18
47
47
1 (T1)
RX-R
43
43
22
22
2 (R1)
TX-T
44
44
34
34
4 (T)
TX-R
19
19
9
9
5 (R)
RX-T
20
20
48
48
1 (T1)
RX-R
45
45
23
23
2 (R1)
TX-T
46
46
35
35
4 (T)
TX-R
21
21
10
10
5 (R)
RX-T
22
22
49
49
1 (T1)
RX-R
47
47
24
24
2 (R1)
TX-T
48
48
36
36
4 (T)
TX-R
23
23
11
11
5 (R)
RX-T
24
24
50
50
1 (T1)
RX-R
49
49
25
25
2 (R1)
TX-T
50
50
37
37
4 (T)
TX-R
25
25
12
12
5 (R)
1 For 21-port E1 modules, one module can be connected to the patch panel.
2 Indicates port numbers from the module connectors and through the patch panel.
3 Pins 13 and 38 are not used. On the patch panel, the two Cinch sockets are labeled PORT 1–12, and PORT
13–24 and match with the RJ-48C connectors labeled 1–24. The pin assignments are the same for each connector.
To the PSAX 48-Port RJ Patch Panel
Table A-2 lists the pin assignments between the 21-Port High-Density E1
IMA module connectors, the Lucent cable, and the PSAX 48-Port RJ Patch
Panel connectors, four 50-pin Cinch plugs and the 48 RJ-48C sockets.
Note:
The transmit and receive—tip and ring—pairs of the patch panel
RJ-48C sockets are reversed from the standard RJ-48C pin
assignments described in the ANSI T1.403 standard (Pin 1 R1, Pin
2 T1, Pin 4 R, and Pin 5 T).
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
A-5
Appendix A Pin Configurations
Connector Pin Assignments
Table A-2. 21-Port High-Density E1 IMA Module Connector, Cable, and PSAX 48-Port RJ Patch Panel Pin
Assignments
Lucent Cable
(COMCODE 300550639)
Module Connectors
Port1
1/13/25/37
2/14/26/38
3/15/27/39
4/16/28/40
5/17/29/41
6/18/30/42
7/19/31/43
8/20/32/44
Signal Name Socket Pin #2
Mini Champ Cinch Socket
Plug P1
P2
RX-T
1
1
39
39
1 (T1)
RX-R
26
26
14
14
2 (R1)
TX-T
27
27
26
26
4 (T)
TX-R
2
2
1
1
5 (R)
RX-T
3
3
40
40
1 (T1)
RX-R
28
28
15
15
2 (R1)
TX-T
29
29
27
27
4 (T)
TX-R
4
4
2
2
5 (R)
RX-T
5
5
41
41
1 (T1)
RX-R
30
30
16
16
2 (R1)
TX-T
31
31
28
28
4 (T)
TX-R
6
6
3
3
5 (R)
RX-T
7
7
42
42
1 (T1)
RX-R
32
32
17
17
2 (R1)
TX-T
33
33
29
29
4 (T)
TX-R
8
8
4
4
5 (R)
RX-T
9
9
43
43
1 (T1)
RX-R
34
34
18
18
2 (R1)
TX-T
35
35
30
30
4 (T)
TX-R
10
10
5
5
5 (R)
RX-T
11
11
44
44
1 (T1)
RX-R
36
36
19
19
2 (R1)
TX-T
37
37
31
31
4 (T)
TX-R
12
12
6
6
5 (R)
RX-T
14
14
45
45
1 (T1)
RX-R
39
39
20
20
2 (R1)
TX-T
40
40
32
32
4 (T)
TX-R
15
15
7
7
5 (R)
RX-T
16
16
46
46
1 (T1)
RX-R
41
41
21
21
2 (R1)
TX-T
42
42
33
33
4 (T)
TX-R
17
17
8
8
5 (R)
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
A-6
PSAX 48-Port RJ Patch
Panel
RJ-48C
Cinch Plug Socket Pin #
Pin #
(CPE)
Release 10.0.0
255-700-584
Appendix A Pin Configurations
Connector Pin Assignments
Table A-2. 21-Port High-Density E1 IMA Module Connector, Cable, and PSAX 48-Port RJ Patch Panel Pin
Assignments (Continued)
Lucent Cable
(COMCODE 300550639)
Module Connectors
Port1
9/21/33/45
10/22/34/46
11/23/35/47
12/24/36/48
Signal Name Socket Pin #2
Mini Champ Cinch Socket
Plug P1
P2
PSAX 48-Port RJ Patch
Panel
RJ-48C
Cinch Plug Socket Pin #
(CPE)
Pin #
RX-T
18
18
47
47
1 (T1)
RX-R
43
43
22
22
2 (R1)
TX-T
44
44
34
34
4 (T)
TX-R
19
19
9
9
5 (R)
RX-T
20
20
48
48
1 (T1)
RX-R
45
45
23
23
2 (R1)
TX-T
46
46
35
35
4 (T)
TX-R
21
21
10
10
5 (R)
RX-T
22
22
49
49
1 (T1)
RX-R
47
47
24
24
2 (R1)
TX-T
48
48
36
36
4 (T)
TX-R
23
23
11
11
5 (R)
RX-T
24
24
50
50
1 (T1)
RX-R
49
49
25
25
2 (R1)
TX-T
50
50
37
37
4 (T)
TX-R
25
25
12
12
5 (R)
1 Indicates port numbers from the module connectors and through the patch panel.
2 Pins 13 and 38 are not used. On the patch panel, the four Cinch sockets are labeled PORT 1–12, PORT 13–24,
PORT 25–36, and PORT 37–48 and match with the RJ-48C connectors labeled 1–48. The pin assignments
are the same for each connector.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
A-7
Appendix A Pin Configurations
Connector Pin Assignments
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
A-8
Release 10.0.0
255-700-584
B
Reference Tables
Overview of This Appendix
This appendix contains reference information that is helpful while configuring your PSAX system. The following types of information are provided:
•
“Avoiding Common Errors When Configuring Interfaces”
•
“Optimizing SVC Call Performance”
•
“Connection Type by Interface Type Table”
•
“Interface Type by I/O Module Type Table”
•
“Module Alarm Status Table”
•
“ATM Service Categories in the PSAX System”
•
“ATM TS, UPC, and VI Configuration Capabilities”
Avoiding Common Errors When Configuring Interfaces
An error may occur when you apply an interface to a channel. If an error
condition occurs, the PSAX system sends an SNMP trap that is usually displayed in the console Trap Log Display window (accessible from the Console
Interface Main Menu window). The list below includes the most common
interface errors that cause the PSAX system to display a message. (See the
PacketStar&reg; PSAX Simple Network Management Protocol (SNMP) Trap Reference
Guide for more information about the SNMP traps related to interface errors).
•
Entering field values that are outside of the configurable range of values
•
Attempting to configure an interface for a port or channel that has
already been configured
•
Attempting to configure an interface that is already in service (must be
out of service to be configured or change field values)
•
Entering field values that are not recognized by the PSAX system
software
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
B-1
Appendix B Reference Tables
Optimizing SVC Call Performance
Optimizing SVC Call Performance
The information in this section provides guidance on optimizing call
performance when configuring SVCs on the PNNI interface. The servicespecific connection-oriented protocol (SSCOP) parameter is set on these
interface configuration windows: ATM IISP network or IISP user, ATM
UNI 3.0 or UNI 3.1, or ATM PNNI 1.0.
Note:
These settings are suggested for connecting to a PSAX system from
a remote site only. The PSAX system configures these settings
internally in its own ATM switch.
When unacknowledged protocol data units (PDUs), the MaxPD field on the
remote end peer (such as the NavisCore™ CBX 500™) shows the maximum
number of SSCOP packets transmitted since the last PSAX polling of the peer.
To optimize call performance, the SSCOP Rx Window Size field of the local
ATM interface should be less than the maximum value displayed in the
MaxPD credit window at the remote end of the ATM interface. Otherwise,
the rate at which switched calls can be set and released may be degraded.
On the ATM IISP Interface Configuration window, the maximum credit
window (the SSCOP Rx Window Size field) is configurable with a value up to
32 for all ATM interfaces on the PSAX system. The interfaces of the ATM
switches that are connected to the PSAX system should be configured with
the same values. This method results in 100 percent call completion at a call
setup rate of 60 calls per second using even distribution. If these values are
not configured in this way, calls will be set up at a rate of less than 60 calls
per second.
Note:
Various SSCOP parameter settings determine the maximum credit
window. As a result, you may not be able to directly use these
settings.
For more information on the SSCOP parameter, see the Application Note
entitled Connecting a CBX or GX Switch to a PacketStar&reg; PSAX Multiservice Media
Gateway via an ATM Port.
Connection Type by Interface Type Table
The PacketStar&reg; PSAX Multiservice Media Gateway provide a number of connection types and interface types to the network as described in Table B-1.
Configuring interfaces and connections are described in the PacketStar&reg; PSAX
Connections Provisioning Guide that can be found on the PacketStar&reg; PSAX Multiservice Media Gateways Product Information Library CD-ROM.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-2
Release 10.0.0
255-700-584
Appendix B Reference Tables
Connection Type by Interface Type Table
AAL2 PVC Trunk
X X X X X X
AAL2 Channel PVC VCC Connection
X X X X X X
Terminal Emulation
HDLC Pass-through
PRI ISDN (Network/User)
GR-303
Frame Relay (UNI, NNI)
CAS TrunkLine
Circuit Emulation
Bridge
ATM PNNI 1.0
ATM PNNI over VPC
ATM UNI 3.0/3.1/4.0
ATM Virtual Interface
Connection Type
ATM IMA
Interface Type
ATM IISP (Network/User)
Table B-1. Connection Type by Interface Type
ATM-to-ATM virtual channel connection (VCC) X X X X X X
PVC
ATM-to-ATM virtual path connection (VPC)
PVC
X X X
X
Bridge-to-ATM VCC PVC
X X X X X X X
Bridge-to-bridge PVC
X
Circuit emulation-to ATM VCC PVC
X X X X X X
X
Circuit emulation-to circuit emulation PVC
X
CPU Ethernet Bridge PVC
X X X X X X
Frame relay-to-ATM VCC PVC
X X X X X X
X
Frame relay-to-frame relay PVC
GR-303-to-AAL2 VCC PVC
1
X
X X X X X X
In-band management ATM PVC
X X X X X X
Variable bit rate (VBR)-to-ATM VCC PVC
X X X X X X
X2
VBR-to-VBR PVC
In-Band Management SVC
X X X X X X
ATM-to-ATM VCC SPVC
X X X X X
ATM-to-ATM VPC SPVC
X X X
Circuit emulation-to-ATM VCC SPVC
X X X X X X
X
CE-to-ATM Std AAL2 VCC SPVC
X X X X X
X
Enhanced Router Module to ATM VCC SPVC
X
Frame relay-ATM VCC SPVC
X X X X X
VBR-to-ATM VCC SPVC
X X X X X
VBR-to-ATM Std AAL2 VCC SPVC
X X X X X
X
X
X
X
X
X
X
X
X X X
X
X
1
AAL2 PVCs must be configured before GR-303 connections can be configured.
2
A GR-303 Interface Group (IG) must be configured before GR-303 connections can be configured.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
X
Release 10.0.0
B-3
Appendix B Reference Tables
Interface Type by I/O Module Type Table
Interface Type by I/O Module Type Table
Table B-2 shows the available interface types for each PacketStar PSAX I/O
module used in the PacketStar&reg; PSAX Multiservice Media Gateway. This table
does not include other PSAX modules that are not I/O modules, which
include: the Alarm module, the DSP2x modules, the Enhanced Router module, the Route Server module, and the Tones and Announcements Server
module
.
GR-303
HDLC Pass-through
PRI ISDN (Network/User)
X
X
X
X
X
X
X
X
X
X
X
V5.2
Frame Relay (UNI, NNI)
X
Terminal Emulation
Circuit Emulation
X
Routing
CAS Trunkline
X
Bridge
X
ATM UNI 3.0/3.1
X
ATM UNI 4.0
ATM PNNI over VPC
ATM PNNI 1.0
X
ATM Virtual Interface
Module
ATM IMA
Interface
ATM IISP (Network/User)
Table B-2. Interface Type by I/O Module Type
DS1/T1 Interface Modules
6-Port DS1 IMA
X
6-Port Enhanced DS1/T1
Multiservice
X
X
12-Port Medium-Density
DS1 Multiservice
X
X
12-Port Medium-Density
DS1 IMA
X
X
X
X
X
X
X
12-Port Medium-Density
DS1/E1/DS0A CES
X1 X2
24-Port High-Density DS1
Multiservice
X
X
X
X
8-Port HDSL-2
X
X
X
X
X
X
X3
X
X
X4
X
X
X
DS3, E3, and STS-1e Interface Modules
1-Port Channelized DS3
Multiservice
X
1-Port DS3 IMA
X
X
X
X
X
X
X
X
X
X
1-Port Unchannelized DS3
Frame Relay
X X
X
1-Port Channelized STS-1e,
T1 Format
X
X
X
X
2-Port DS3 ATM
X
X
X
X
2-Port E3 ATM
X
X
X
X
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-4
X X
X
X X
X X
Release 10.0.0
255-700-584
Appendix B Reference Tables
Interface Type by I/O Module Type Table
X
X
3-Port Channelized
DS3/STS-1e Multiservice
Protection
X
V5.2
X
Terminal Emulation
X
GR-303
3-Port Channelized
DS3/STS-1e CES Protection
Routing
PRI ISDN (Network/User)
HDLC Pass-through
Frame Relay (UNI, NNI)
Circuit Emulation
X
Bridge
X
ATM UNI 3.0/3.1
X
ATM UNI 4.0
X
Module
ATM PNNI 1.0
3-Port Channelized
DS3/STS-1e CES
Interface
ATM IMA
CAS Trunkline
ATM Virtual Interface
ATM PNNI over VPC
ATM IISP (Network/User)
Table B-2. Interface Type by I/O Module Type (Continued)
X
3-Port DS3/E3 ATM
X
X
X
X
X
3-Port DS3/E3 ATM
Protection
X
X
X
X
X
3-Port Unstructured
DS3/E3 CES
X
3-Port Unstructured
DS3/E3 CES Protection
X
E1 Interface Modules
6-Port E1 IMA
X
6-Port Enhanced E1
Multiservice
X
X
X
X
X
X
X
X
X
X
X
X
X
21-Port High-Density E1
Multiservice
X
X
X
X
X
X
X
X
X
23N34
21-Port HighDensity E1 IMA
X
X
X
X
X
X
Ethernet Interface Modules
Ethernet
X
X
4-Port Ethernet
X
X
Fiber-Optic Interface Modules
1-Port Channelized
OC-3/STM-1 CES
Multimode
X
X
1-Port Channelized
OC-3/STM-1 CES Singlemode
X
X
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
X
Release 10.0.0
B-5
Appendix B Reference Tables
Interface Type by I/O Module Type Table
1-Port Channelized
OC-3/STM-1 Unstructured
CES/ATM Single-Mode
X5
X5
X5 X5
X6
1-Port Channelized OC3/STM-1 Unstructured
CES/ATM Multimode
X5
X5
X5 X5
X6
2-Port OC-3c/STM-1 ATM
Multimode
X
X
X
X
2-Port OC-3c/STM-1 ATM
Single-Mode
X
X
X
X
4-Port OC-3c/STM-1
Multimode
X
X
X
X
4-Port OC-3c/STM-1
Single-Mode
X
X
X
X
1-Port OC-3c 1+1 APS
Multimode
X
X
X
X
X
1-Port OC-3c 1+1 APS
Single-Mode
X
X
X
X
X
1-Port STM-1 1+1 MSP
Multimode
X
X
X
X
X
1-Port STM-1 1+1 MSP
Single-Mode
X
X
X
X
X
1-Port OC-12c/STM-4c
Multimode
X
X
X
X
X
1-Port OC-12c/STM-4c
Single-Mode
X
X
X
X
X
2-Port OC-3c/STM-1
Enhanced ATM Multimode
X
X
X
X
2-Port OC-3c/STM-1
Enhanced ATM SingleMode
X
X
X
X
V5.2
Terminal Emulation
Routing
PRI ISDN (Network/User)
HDLC Pass-through
GR-303
Frame Relay (UNI, NNI)
Circuit Emulation
CAS Trunkline
Bridge
ATM UNI 3.0/3.1
ATM UNI 4.0
ATM PNNI over VPC
ATM PNNI 1.0
ATM Virtual Interface
Module
ATM IMA
Interface
ATM IISP (Network/User)
Table B-2. Interface Type by I/O Module Type (Continued)
Serial Interface Modules
Quadserial
X
X
X
X
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-6
X
X
X
X
Release 10.0.0
255-700-584
Appendix B Reference Tables
Module Alarm Status Table
X
V5.2
Terminal Emulation
Routing
PRI ISDN (Network/User)
X
HDLC Pass-through
Frame Relay (UNI, NNI)
X
GR-303
Circuit Emulation
CAS Trunkline
X
Bridge
X
ATM Virtual Interface
ATM UNI 3.0/3.1
ATM PNNI over VPC
6-Port Multiserial
ATM UNI 4.0
Module
ATM PNNI 1.0
Interface
ATM IMA
ATM IISP (Network/User)
Table B-2. Interface Type by I/O Module Type (Continued)
X
Voice 2-Wire Interface Modules
4-Port Voice 2-Wire Office
X7
8-Port Voice 2-Wire Station
X7
1
The module supports CAS Trunkline in DS1 and E1 modes only.
2
The module supports Circuit Emulation in DS1, E1, and DS0A modes.
3
The module supports GR-303 in DS1 mode only.
4
The module supports PRI ISDN in DS1 and E1 modes only.
5
The module supports ATM services in the STM-ATM mode only.
6
The module supports CE in the OC3-UCE mode only.
7
European modules do not support this interface with the 8-Port Voice 2-Wire Station module or the 4-Port
Voice 2-Wire Office module.
Module Alarm Status Table
The Alarm Status field on the Equipment Configuration window is described
in Table B-3.
Table B-3. Module Alarm Status Descriptions on the Equipment Configuration Window
Alarm Status
Module Type
Affected
Description
NoAlarm
I/O and Server Indicates that no alarms have been detected for the module
in this slot.
WrongCardType
I/O and Server Indicates that one type of module was configured in this
slot in the chassis, but a now different module occupies this
slot.
LineFailed
All
Indicates that the module in this slot is no longer receiving
or transmitting signals because the line failed.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
B-7
Appendix B Reference Tables
Module Alarm Status Table
Table B-3. Module Alarm Status Descriptions on the Equipment Configuration Window (Continued)
Alarm Status
Module Type
Affected
Description
Hexadecimal format,
Example:
12345678ABC
I/O and Server Indicates that one or more ports on the module in this slot
currently have a loss of signal. The numbers indicate which
ports have a loss of signal. For modules that have more
than eight ports not receiving signals, the value in this field
is in hexadecimal format.
CardRemoved
All
Indicates that one of the following events occurred:
• The module in this slot was configured and then
removed from the slot.
• Connections on the OC-3, OC-12, STM-1, or STM-4
APS/MSP primary module in this slot were transferred to
the standby module. After the transfer occurs, the former
primary module then displays CardRemoved in the
Alarm Status field; the former standby module then displays Primary in the Status field.
ReferenceClockFailed Stratum 3–4
Indicates that the timing reference clock on the Stratum
module in this slot failed.
CompositeClockFailed Stratum 3–4
Indicates that the timing composite clock on the Stratum
module in this slot failed.
Overload
Power Supply
Indicates that the Power Supply module is operating under
an overload condition.
PowerFailed
Power Supply
Indicates that the power has failed.
Minus48vFailed
Power Supply
Indicates that the -48 V dc Power Supply module output
failed.
UnknownAlarm
I/O and Server Indicates that the reason for failure is not known.
CompleteClockFailed Stratum 3–4
Indicates that the backplane detected a clock error.
PowerFailed
Indicates that no power is coming into the PSAX chassis.
Power Supply
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-8
Release 10.0.0
255-700-584
Appendix B Reference Tables
ATM Service Categories in the PSAX System
ATM Service Categories in the PSAX System
ATM Service Category Descriptions
The PSAX system support of defined ATM quality of service (QoS) categories
is described in Table B-4.
Table B-4. PSAX System-Supported Quality of Service Categories
ATM Service Category
Description
Constant Bit Rate (CBR) This service offers consistent delay predictability. CBR is used for applications such as circuit emulation, voice, and video.
Real Time Variable Bit
Rate (VBR-rt)
This service offers low delay variance, but requires access to a variable
amount of network bandwidth. VBR-rt is used for applications such as
packet video and voice.
Non-Real Time Variable This service allows delay variance between the delivery of cells. VBR-nrt
Bit Rate (VBR-nrt)
is used for data applications that have potentially bursty traffic characteristics.
Guaranteed Frame Rate This service allows delay variance and offers a minimum cell rate guaran(GFR)
tee. When used with frame-based data encapsulated in AAL5 PDUs, it
provides frame-based cell discard. GFR is used for frame relay or ethernet
over ATM.
Unspecified Bit Rate
(UBR)
This service allows for best-effort transport by the network. Cells are
transported by the network whenever bandwidth is available and the
user presents traffic.
Priority of ATM Service Categories in the PSAX System
The attributes of the categories of service supported by the PSAX system
software are identified in Table B-5. The service examples in this table are
intended simply as illustrations; you should choose your service category
based on your network applications supported by the PSAX system. The
flexibility of the PSAX system allows you to tailor the system based on the
required service applications by selecting the appropriate connection
configuration selection field value.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
B-9
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-5. Mapping ATM Service Categories to PSAX System Priority Levels
ATM Forum Traffic Management
Connection AQueMan Priority 4.1 Priority (Current ImplementaConfiguration
(Legacy Impletion)
Field Value
mentation)
ATM Service Category
Constant Bit Rate (CBR)
CBR1
Highest
CBR2
Lower than
CBR1
Preferred customers
CBR3
Lower than
CBR2
Standard
CBR4
Lower than
CBR3
Cellular
VBR-express
Lower than
CBR4
VBR-rt1
Lower than
VBR-express
Real-time video
VBR-rt2
Lower than
VBR-rt1
MPEG 1-2/JPEG
VBR-nrt1
Lower than
VBR-rt2
VBR-nrt2
Lower than
VBR-nrt1
Guaranteed Frame Rate
(GFR)
GFR2
Lowest (shares
queue with UBR)
Lower than
VBR-nrt
Frame relay,
Ethernet, TCP
Unspecified Bit Rate
(UBR)
UBR
Lowest
Lowest
UDP
Real Time Variable Bit
Rate (VBR-rt)
Non-Real Time Variable
Bit Rate (VBR-nrt)
Highest
Service Examples
911 calls
Lower than CBR
Network
management
Lower than
VBR-rt
Data
Data
ATM TS, UPC, and VI Configuration Capabilities
Configuration compatibility among the ATM Traffic Shaping, UPC Support,
and VI Support features is shown in Table B-6. In the table, Yes indicates that
the two features coinciding in the matrix can be configured in the same
interface, and No indicates that they cannot. See Figure B-1 for an illustration of this concept.
Table B-6. ATM Traffic Shaping, UPC Support, and VI Support Configuration
Compatibility
Fields on ATM UNI, PNNI, and IISP
Configuration Windows
ATM Traffic
Shaping per VC VI Support
ATM Traffic Shaping per VC
VI Support
UPC Support
No
No
Yes
1
Yes
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-10
UPC Support
Yes1
Yes
Release 10.0.0
255-700-584
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
1
UPC support and Traffic Shaping per VC are supported on the same end-to-end connection only when VI is configured on the egress path, and UPC on the ingress path.
I/O Module 1
Rx
Ingress Path
UPC
Tx
VI or TS
Egress Path
Chassis Backplane
I/O Module 2
Rx
Ingress Path
UPC
Tx
VI or TS
Egress Path
Figure B-1.
Combining the UPC Feature and Either the TS or VI Feature on a
Connection
ATM Traffic Shaping Capability by Module
The ATM Traffic Shaping capability is supported on the PSAX modules
listed in Table B-7. The table includes information on the maximum
number of VCs using traffic shaping, minimum PCR for traffic shaping,
queue size, priority, and precision of traffic shaping for one connection.
Configuration compatibility among the ATM Traffic Shaping, UPC Support, and VI Support features is shown in
The PSAX modules supporting ATM Traffic Shaping, UPC, or VI are
listed in Table B-7. The table includes information on the maximum
number of VCs using traffic shaping, minimum PCR for traffic shaping,
queue size, priority, and precision of traffic shaping for one connection.
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Release 10.0.0
B-11
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-7. ATM Traffic Management Capabilities by Module
Feature Support
Modules
ATM Traffic Shaping (TS)
Max.
Min.
Precision for One
Queue
No. of
1
Size
PCR
Connection2
EPD GFR UPC VI TS
Priority
VCs
DS1/T1 Interface Modules
12-Port Medium-Density DS1
IMA
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
12-Port Medium-Density DS1
Multiservice
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
24-Port High-Density DS1
Multiservice
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
E1 Interface Modules
23N34
E1 IMA
21-Port High-Density
21-Port High-Density E1
Multiservice
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
DS3, E3, and STS-1e Interface Modules
1-Port Channelized STS-1e, T1
Format
x
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
1-Port DS3 IMA
x3
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
1-Port Channelized DS3
Multiservice
x3
x
32,000
150
cps
2&times;
MBS
After
VBR-rt2
~50% of line
rate
3-Port DS3/E3 ATM
x
x
32,000
7 cps
2&times;
MBS
After
CBR
~1% of line rate
x
Fiber-Optic Interface Modules
1-Port OC-12c/STM-4c
Multimode
x
x
x
32,000
87 cps
2&times;
MBS
After
CBR
~1% of line rate
1-Port OC-12c/STM-4c
Single-Mode
x
x
x
32,000
87 cps
2&times;
MBS
After
CBR
~1% of line rate
1-Port Channelized OC3/STM-1 Unstructured
CES/ATM Multimode
x
x
32,000
9 cps
2&times;
MBS
After
CBR
~50% of line
rate
1-Port Channelized
OC-3/STM-1 Unstructured
CES/ATM Single-Mode
x
x
32,000
9 cps
2&times;
MBS
After
CBR
~50% of line
rate
2-Port OC-3c/STM-1 ATM
Multimode
x
x
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
2-Port OC-3c/STM-1 ATM
Single-Mode
x
x
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
2-Port OC-3c/STM-1 Enhanced
ATM Multimode
x
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-12
Release 10.0.0
255-700-584
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-7. ATM Traffic Management Capabilities by Module (Continued)
Feature Support
Modules
EPD GFR UPC
VI
ATM Traffic Shaping (TS)
TS
Max.
No. of
VCs
Min.
PCR1
Queue
Size
Priority
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
Precision for One
Connection2
2-Port OC-3c/STM-1 Enhanced
ATM Single-Mode
x
4-Port OC-3c/STM-1
Multimode
x
x
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
4-Port OC-3c/STM-1
Single-Mode
x
x
x
32,000
24 cps
2&times;
MBS
After
CBR
~1% of line rate
N/A
N/A
N/A
N/A
Serial Interface Modules
Quadserial
N/A
x3
1
If you specify a rate below the minimum supported PCR, the module defaults to traffic shaping at the minimum supported PCR.
2
A connection configured for a PCR less than the specified rate has an output rate within 1% of the configured PCR.
3
UPC is available only when using channelization to DS0s.
ATM Traffic Shaping Sample CPS Calculation Table
Use the information in Table B-8 as a guide for calculations to determine
ATM traffic shaping for cps on the
Sample calculation: If the ATM traffic-shaped connection is configured with
the PCR (Minimum/Actual Target CPS column) value 906 and the maximum
target CPS (Maximum Target CPS column) value 909, the ATM Traffic Shaping feature is actually shaping the traffic to the (Actual CPS column) value
906 cps. The divergence is smallest at low PCR.
Table B-8. ATM Traffic Shaping CPS Calculation Table
Actual Rate (in
bps)
Minimum/Actual Maximum Target
Target CPS
CPS
64,000
151
152
151
128,000
302
303
302
192,000
453
454
453
256,000
604
606
604
320,000
755
757
755
383,999
906
909
906
448,383
1,058
1,062
1,058
512,876
1,210
1,215
1,210
575,999
1,358
1,365
1,358
639,999
1,509
1,517
1,509
713,142
1,682
1,691
1,682
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Actual CPS
Release 10.0.0
B-13
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-8. ATM Traffic Shaping CPS Calculation Table (Continued)
Actual Rate (in
bps)
Minimum/Actual Maximum Target
Target CPS
CPS
767,999
1,811
1,822
1,811
831,999
1,962
1,974
1,962
896,765
2,115
2,129
2,115
959,999
2,264
2,280
2,264
1,025,752
2,419
2,437
2,419
1,085,216
2,559
2,579
2,559
1,151,998
2,717
2,739
2,717
1,217,559
2,872
2,896
2,872
1,279,998
3,019
3,046
3,019
1,349,187
3,182
3,212
3,182
1,412,828
3,332
3,365
3,332
1,482,770
3,497
3,533
3,497
1,543,915
3,641
3,680
3,641
1,610,320
3,798
3,840
3,798
1,663,997
3,925
3,970
3,925
1,741,393
4,107
4,156
4,107
1,782,854
4,205
4,257
4,205
1,804,335
4,256
4,308
4,256
1,826,339
4,307
4,362
4,307
1,848,886
4,361
4,416
4,361
1,871,997
4,415
4,472
4,415
1,895,693
4,471
4,529
4,471
1,919,997
4,528
4,588
4,528
1,944,932
4,587
4,648
4,587
1,970,523
4,647
4,710
4,647
1,996,797
4,709
4,774
4,709
2,023,781
4,773
4,839
4,773
2,051,504
4,838
4,907
4,838
2,079,997
4,906
4,976
4,906
2,109,293
4,975
5,047
4,975
2,139,425
5,046
5,120
5,046
2,170,431
5,119
5,195
5,119
2,202,350
5,194
5,273
5,194
2,235,220
5,272
5,353
5,272
2,269,087
5,352
5,435
5,352
2,303,996
5,434
5,520
5,434
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-14
Actual CPS
Release 10.0.0
255-700-584
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-8. ATM Traffic Shaping CPS Calculation Table (Continued)
Actual Rate (in
bps)
Minimum/Actual Maximum Target
Target CPS
CPS
2,339,996
5,519
5,607
5,519
2,377,139
5,606
5,698
5,606
2,415,480
5,697
5,791
5,697
2,455,078
5,790
5,888
5,790
2,495,996
5,887
5,988
5,887
2,538,301
5,987
6,091
5,987
2,582,065
6,090
6,198
6,090
2,627,364
6,197
6,308
6,197
2,674,282
6,307
6,423
6,307
2,722,905
6,422
6,542
6,422
2,773,329
6,541
6,665
6,541
2,825,656
6,664
6,793
6,664
2,879,996
6,792
6,927
6,792
2,936,466
6,926
7,065
6,926
2,995,195
7,064
7,209
7,064
3,056,322
7,208
7,359
7,208
3,119,995
7,358
7,516
7,358
3,186,378
7,515
7,679
7,515
3,255,647
7,678
7,850
7,678
3,327,995
7,849
8,028
7,849
3,403,631
8,027
8,215
8,027
3,482,785
8,214
8,411
8,214
3,565,709
8,410
8,616
8,410
3,652,677
8,615
8,831
8,615
3,743,994
8,830
9,058
8,830
3,839,994
9,057
9,296
9,057
3,941,047
9,295
9,547
9,295
4,047,561
9,546
9,812
9,546
4,159,994
9,811
10,093
9,811
4,278,851
10,092
10,389
10,092
4,404,699
10,388
10,704
10,388
4,538,175
10,703
11,039
10,703
4,679,993
11,038
11,395
11,038
4,830,960
11,394
11,775
11,394
4,991,992
11,774
12,181
11,774
5,164,130
12,180
12,616
12,180
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
255-700-584
Actual CPS
Release 10.0.0
B-15
Appendix B Reference Tables
ATM TS, UPC, and VI Configuration Capabilities
Table B-8. ATM Traffic Shaping CPS Calculation Table (Continued)
Actual Rate (in
bps)
Minimum/Actual Maximum Target
Target CPS
CPS
5,348,563
12,615
13,083
12,615
5,546,658
13,082
13,586
13,082
5,759,991
13,585
14,129
13,585
5,990,391
14,128
14,718
14,128
6,239,990
14,717
15,358
14,717
6,511,294
15,357
16,056
15,357
6,807,262
16,055
16,820
16,055
7,131,418
16,819
17,661
16,819
7,487,988
17,660
18,591
17,660
7,882,093
18,590
19,624
18,590
8,319,987
19,623
20,778
19,623
8,809,398
20,777
22,076
20,777
9,359,986
22,075
23,548
22,075
9,983,985
23,547
25,230
23,547
10,697,126
25,229
27,171
25,229
11,519,982
27,170
29,435
27,170
12,479,981
29,434
32,111
29,434
13,614,524
32,110
35,322
32,110
14,975,977
35,321
39,246
35,321
16,639,974
39,245
44,152
39,245
18,719,971
44,151
50,459
44,151
21,394,253
50,458
58,869
50,458
24,959,961
58,868
70,642
58,868
29,951,954
70,641
88,303
70,641
37,439,942
88,302
117,737
88,302
49,919,923
117,736
176,605
117,736
PacketStar&reg; PSAX 21-Port High-Density E1 IMA Module User Guide, Issue 1
B-16
Actual CPS
Release 10.0.0
255-700-584
Part Number: 547M0A10001D1
Copyright &copy; 2004 Lucent Technologies
All rights reserved.
">
Hallo! Ich bin ein KI-Chatbot, der speziell dafür ausgebildet wurde, Ihnen bei der Lucent Technologies PSAX 23N34 Benutzerhandbuch zu helfen. Ich habe das Dokument gründlich gelesen und kann Ihnen helfen, die benötigten Informationen zu finden oder den Inhalt klar und einfach zu erklären. Egal, ob Sie nach Anleitungen zu bestimmten Funktionen, Problemlösungen oder allgemeinen Nutzungshinweisen suchen, zögern Sie nicht, Ihre Fragen zu stellen. Je mehr Details Sie zu Ihren Anliegen oder Bedürfnissen bereitstellen, desto genauer und effektiver kann ich Ihnen helfen!
Assistent tippt
Assistent ist nicht an der Tastatur. Bitte versuchen Sie es später noch einmal.
Es sieht so aus, als ob Sie ein Dokument erreicht haben, das in mehreren Sprachen verfasst ist, einschließlich einer Sprache, die nicht Ihre Muttersprache ist. Sie können die folgenden Links verwenden, um Seiten ohne die von Ihnen bevorzugte Sprache vorübergehend auszublenden.
Verwandt

E1 Multiservice Module PSAX 23N66 User Guide

PSAX 23A35 Installation Guide

PSAX 23N60, PSAX 1000, PSAX 1250, PSAX 2300, PSAX 4500 User Guide

PSAX 23N28 User Guide - Tones and Announcements Server Module

PSAX 4-Port Ethernet User Guide

PSAX Module PSAX 23N73, PSAX Module PSAX 23N72 User Guide

STM-1 1+1 MSP Modules PSAX 1-Port STM-1 1+1 MSP User Guide

Lucent Technologies PSAX 20N32 User Guide

PSAX 2-Port E3 ATM Module User Guide

DS1/E1/DS0A CES Module PacketStar PSAX 24N64 User Guide

DS1/E1/DS0A CES Module PacketStar PSAX 24N64 User Guide

PSAX 1-Port STM-1 1+1 MSP Module 20N93, 20N92 User Guide
