LG WF-S5207PH Owner’s Manual
Add to my manuals28 Pages
The LG WF-S5207PH washing machine is a versatile laundry solution for various fabric types and cleaning needs, offering features like Fuzzy Logic Control for optimized washing conditions, 3-step washing for effective cleaning with low tangling, a lint filter for cleaner washes, auto restart in case of power failures, and various washing programs for specific fabric types and washing requirements.
advertisement
▼
Scroll to page 2
of 28
Washing Machine OWNER'S MANUAL MODELS : WF-S(C/F)5101(~5)PC(H/P),S(C/F)5101(~5)PD(E/F) WF-S(C/F)5111(~5)PC(H/P),S(C/F)5111(~5)PD(E/F) WF-S(C/F)5201(~7)PC(H/P),S(C/F)5201(~7)PD(E/F) WF-S(C/F)5211(~7)PC(H/P),S(C/F)5211(~7)PD(E/F) WF-S(C/F)6101(~5)TC(H/P),S(C/F)6101(~5)TD(E/F) WF-S(C/F)6111(~5)TC(H/P),S(C/F)6111(~5)TD(E/F) WF-S(C/F)6201(~7)TC(H/P),S(C/F)6201(~7)TD(E/F) WF-S(C/F)6211(~7)TC(H/P),S(C/F)6211(~7)TD(E/F) WF-S(C/F)5301(~7)TC(H/P),S(C/F)5311(~7)TD(E/F) WF-S(C/F)5401(~5)TC(H/P),S(C/F)5411(~5)TD(E/F) Please read this manual carefully before operating your set. Retain it for future reference. Record model name and serial number of the set. Quote this information to your dealer when you require service. P roduct Features Fuzzy Logic Control A built-in load automatically detects and measures the laundry load and microprocessor optimizes washing conditions such as ideal water level and washing time. Advanced technology is built into the Electronic Control System which ensures the best washing result. SENSING SETTING AUTO sensor a START Laundry Sensor Water Level Sensor Optimum Washing WASHING Condition 3 POWER OFF Step washing 3 step washing makes best washing effect with low tangling. Rubbing and Shaking Rubbing Shaking and Disentangling Lint Filter Lint and loose threads from during the washing cycle for a are laundry generated caught by the lint filter cleaner wash. Auto Restart In the event of start its ※ a power failure, the washing machine will automatically interrupted cycle Applied models : Be : when power is resumed. WF-S(C/F)5101(~5)PD(E/F),S(C/F)5111(~5)PD(E/F) WF-S(C/F)5201(~7)PD(E/F),S(C/F)5211(~7)PD(E/F) WF-S(C/F)6101(~5)TD(E/F),S(C/F)6111(~5)TD(E/F) WF-S(C/F)6201(~7)TD(E/F),S(C/F)6211(~7)TD(E/F) WF-S(C/F)5301(~7)TD(E/F),S(C/F)5311(~7)TD(E/F) WF-S(C/F)5401(~5)TD(E/F),S(C/F)5411(~5)TD(E/F) sure to remove the unit from the carton machine will not be able to operate properly. base, otherwise the C ontents Read this manual Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the section. If you review may not need to call for service at all. Troubleshooting Introduction Before Starting our Safety to Wash chart of Troubleshooting Tips first, information you 4 Identification of Parts 5 Function Information 6 Preparation Before Use of Water, Washing 7 Detergent, Bleach 8 and Softener Washing Programs Additional Function Options Installation Care and Maintenance Function of each Button 10 Fuzzy Wash (Normal Wash) 12 Economy Wash 12 Jean Wash 12 Wool Wash 12 Soak Wash 12 Delay Start (Reservation) Wash 14 Option Washing 15 Other useful Functions 16 Placing and Supply Connecting Water Connecting Drain Hose Grounding 17 Leveling Method Hose 18 21 22 Cleaning 23 Troubleshooting Troubleshooting 25 Specification Specification 27 4 S afety information WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire explosion, electric shock, or to prevent property damage, personal injury, or loss of life. Introducin For your better understanding, these precautions are or separated into two categories. own safety, and protection of your We urge you to pay special attention to them in the interests of your machine against damage: Caution Violation of these Attention guidelines could result in serious injury. Attention appliance is not intended for use by young or infirm persons without supervision. Do not install the washing machine in a damp place. Keep the washing machine away from fire or heat The Do not put your hands children machine. place any rugs or heavy material the power cord. Since the machine is heavy, a minimum of two persons should it. exposed to sunlight, wind, rain, etc. The appliance must be positioned so that the plug is accessible sure to ground the earth wire or connect it ground detector after you put the power cord Make Make Supply to and an move Do not install the washer where it is Power into feet under this over source. a or Do not Young children should be supervised to ensure that they do not play with the appliance. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. cord fatal Following these guidelines will protect your machine against damage. Caution Installation or outlet. sure the power cord is free of dust that the cord will plug it in properly so not move. When the power cord is loose, do not use it. Do not damage the power cords. Do not plug many cords into one Do not touch the power cord with wet hands. outlet at the same time. If the power cord or fuse is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified people in order to avoid a hazard. If the appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set or electrical portable outlet device should be positioned so it is not subject to splashing or ingress of moisture. Do not place any electric appliance with a charging battery, magnetically-driven appliance and magnetic body on the washer. Operation When you take out the fall into the washer. laundry, be careful not to ? Do not put hands into the rotating tub. Do not sprinkle water over the buttons. Make sure the lid is closed during operation of the Do not put heavy objects on the machine. Unplug the cord when the machine is not in Do not press the buttons with sharp objects. Check the hose connection and open the tap before ? spin cycle. Maintenance ? ? ? use. ? activating the machine. Do not pour into the tub. more Do not wash any than 50˚C(122˚F) water waterproof materials. Do not pour corrosive materials or bleach over the washing machine. It will cause damage to the power cord or the machine. Never disassemble or remodel the washer and power cord by yourself. Only a qualified technician should work on the machine. 5 dentification of Parts I Body Power cord supply hose(1 Water Powder Bleach detergent EA or 2EA) * * box dispenser Inner tub Control * panel * Lint filter Drain hose for pump model * Pulsator * Adjustable leg Drain hose for non * pump model Accessories Water supply hoses Drain hose or or 1 Each for cold and hot water Note “ ”Part can be different according to the model. Anti-rat cover (option) Introducin 6 Function Information Our machine provides various types of laundry. BeforStaingWsh Different washing methods which suit various conditions and types of laundry washing Fuzzy (Normal) Wash y Use this Program for normal clothes except for woolen clothes and lingerie. automatically detects the quantity of laundry and selects the appropriate power, washing time, rinsing time and spinning time. (refer to p12 ) The sensor water level, wash Economy Wash Economy wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to p12) Jean Wash Thick and (refer to heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. p12) Wool Wash Delicate clothes (lingerie, wool etc.) which may be easily damaged can be washed. (refer to p12) Soak Wash Soak Wash and can be selected to wash grime. (refer to heavily soiled laundry by soaking in water for some time to remove dirt p12) Other washing methods Delay Start (Reservation) Wash Delay Start (Reservation) Wash is used to delay the finishing time of the operation. Delayed Start washing can be set according to preference. (refer to p14) Option Wash Spin, Rinse/Spin, Rinse, Wash/Rinse, and Wash only options can selected. (refer to p15) 7 Before Preparation Washing BeforStaingWsh Sorting To get the best results, different fabrics need to be washed in different ways. (Heavy, Normal, Light) Separate clothes according to amount of soil COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics. LINT (Lint producers, Collectors) Separate lint producers and lint collectors. SOIL Caring before loading ? Check all such ? ? pockets to make sure that they are empty. Things nails, hairclips, matches, pens, coins and keys can damage as both your washer and your clothes. Close zippers, hook and strings to make become ? sure that these items don't snag on other clothes. Mend any torn garments or loose buttons. Tears or holes may larger during washing. Remove any loose brassiere wires washing machine and clothes. ? Pre-treat dirt and stains. ? Make ? Check the sure the clothes washing are as they can damage your WIRE washable in water. instructions. Pretreatment detergent dissolved in water onto stains like collars help shift dirt. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove. Brush a little and cuffs to Light and Large-size clothing Clothes like downs and woollens are light weight, large and float easily.So use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved detergent to prevent the detergent from clumping. Long laundry items nylon nets for long, delicate items. laundry with long strings or long length, a net will prevent tangling during washing. Fasten zippers or hooks on items before washing. ※ Nylon net is not supplied by LG. Use For 8 Use BeforStaingWsh of Water, Detergent, Bleach and Softener Using water Amount of water ? This machine detects the quantity of laundry automatically, then sets the water level and proper amount of detergent. ? When you select a wash program, the water level and amount of detergent (to be used) will be shown on the control ? panel. When the water level is though Water the The machine sets the ? You can change Using Detergent and Amount of ? on the quantity of laundry even appropriate temperature automatically according to the wash program by pressing the WATER TEMP button. to the water temperature (refer . p10) Fabric Softener detergent detergent. For the correct amount of detergent, refer to Available ? on When you select a wash program, the water level and the amount of detergent will be shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated ? is indicated temperature ? ? it may differ depending the control panel. automatically detected, water level same detergent manufacturer's instruction . Detergent Type Synthetic detergents that yield a low level of foam are recommended. liquid detergent is used, mix it with water (1:1) and pour it into the bleach dispenser. When Attention If excessive pollution, detergent is used, the rinse will not be as clean it accordingly. Available Fabric Softener ? Do not ? For Also, it could cause environmental Type concentrated fabric softener. This may cause some problems in automatic details refer to the softener products instructions for use. use more and efficient. so use dispensing. 9 Depositing Detergent Powder Open the detergent dispenser and deposit the appropriate amount of detergent Detergent dispenser. . Where you deposit the detergent Depositing Fabric ? ? ? ? ? softener Don't use softener with rinse water detergent. When using dispenser, dilute fresh water(30ml) softener(30ml) with When filling dispenser, do not It may stain clothes. Never pour fabric softener It may stain them Use softener in last splash overfill. or directly on clothes. If spotting occurs, wet and rub hand dishwashing liquid (or mild bar soap) and rewash. Note Fabric Softener will be inserted Using Bleach Check fabric care Available Bleach Use automatically during the final rinse. labels for special instructions. Type oxygenated bleach. Powdered bleach should mixed with water and then be For more details refer to the products deposited into the tub. instruction for use. Depositing Bleach Bleach Separate the laundry to be bleached and deposit liquid bleach into the Bleach dispenser. The dispenser dilutes liquid chlorine bleach before dispenser it reaches into your wash load. Do not insert bleach or fabric softener directly Do not mix chlorine bleach with ammonia produce a toxic gas which may cause or death. onto laundry. This may affect colors or damage clothing as vinegar and/or rust remover. Mixing can acids such 10 F BeforStaingWsh unction of each Button Water ? temperature button (option) (indication of detergent amount) Use to select water temperature. Pressing the button allows you to select Cold Warm Cold respectively. (Hot&Cold) Default Water level button ? Hot adjust the water level as required. The appropriate of detergent is shown next to the water level in the WATER-DETERGENT diagram Water level is automatically selected for fuzzy (normal) and jean programs. The following settings are indicated as the button is EX-LARGE SMALL pushed LARGE Use to amount setting is Cold. ? MEDIUM LARGE Process button ? Use to select desired. Note The control panel may differ according to different models SOAK, WASH, RINSE and SPIN functions as 11 Program ? ? Use for selecting wash program. This button allows you to select 4 different programs for different kinds of laundry ? Start/ Pause button button ? light up in sequence as or pause the start and pause Repeats washing process. by pushing the The power goes off automatically 10 minutes after stopping. ※ This appliance is fitted with a safety automatically stops the of the operation washing machine when it is exposed to heavy disturbance on the follows: FUZZY (NORMAL) ECONOMY JEAN WOOL FUZZY Use to start button. ? and dirtiness. program selections ? function that (NORMAL) etc. Select the by pressing the button. desired program mains. Child lock function Use to lock or Delay Start (Reservation) unlock the control buttons to prevent from setting being changed by a child. To lock, push the PROCESS, and PROGRAM buttons simultaneously and to unlock push them one more time during the washing process. (refer to p 16) ? button a delayed finishing time. changes 6→9→15(6+9)→6hr when the button is pushed. Use to set The time (refer to p14) BeforStaingWsh 12 Washing Programs WashingProm Washing AUTO POWER OFF Programs Add the Add the detergent laundry Fuzzy Washing 1 2 4 (Normal Wash) Used for normal loads, this mode ・Add the appropriate quantity of detergent as indicated by the water level next to WATER- automatically selects the most appropriate conditions and completes the sequence in one operation. The built-in sensor DETERGENT. detects the size of the load and the ideal wash power and wash, rinse and spin times are set accordingly Or follow the instructions 1 3 Economy Wash Use this mode when washing lightly solided clothes for a detergent manufacturer's 5 2 ・Select the short time. The ECONOMY weight should be under 2.0kg. program on the Control panel. Jean Wash 1 5 2 3 Use jeans program when washing heavy, thick, and extremely dirty laundry such as jeans and work ・Select the JEAN program on the Control outfits. panel. Wool Wash 1 Use this program for washing delicate fabrics such as 3 lingerie and woolens. 5 2 ・Use neutral ・Select the (wash only "water washable" clothes) Before washing your woolens check the care label for the washing program on the Control instructions. panel. laundry. washing ・When woolens Soak Wash 1 4 some time to will not work remove in WOOL proteins and fats. 'SOAK' mode can be used with all program. Program. washing programs simultaneously except for "WOOL" 3 ・The SOAK excessively dirty laundry by soaking in water for 2 ・Keep pressing the PROCESS button until the SOAK light is on and then WASH, lights are on simultaneously. ・If necessary, select the desired washing process from RINSE, SPIN (SOAK+WASH+RINSE+SPIN), (SOAK+WASH+RINSE), (SOAK+WASH) manually. use a mild detergent recommended for washing wool. (wash only water washable clothes) Use this mode for washing detergent appropriate for the WOOL 6 13 Close the lid 3 ・The pulsator rotates for 8 ・Water will be supplied laundry load. start of the wash to supplement the water laundry has the be used will be shown and absorbed. water will be 4 ・When the wash or putting wet increase the water level. program ends, the buzzer will ring for 10 ・With seconds before the ・Changes to water temperature (hot/cold) and wash level are possible during operation. Power goes off lightweight bulky loads, water level can be set low. (refer to p 10) automatically. supplied. 4 ・If water is already in the tub, laundry into the tub before starting will for 2 minutes after the the amount of detergent to Caution & Note 6 5 seconds to detect the ・Then the water level and Finish 6 7 6 7 ・When setting the water level manually, do not set to MEDIUM to 4 6 7 rgent he prevent damage to laundry. ・Washing with hot water may damage the laundry (Water is set to cold automatically). Ensure that the load is under 2kg ・In order to avoid damage to laundry, the spin cycle may appear slow. This also avoids wrinkles and clothing may still contain ild some water. This is normal. ・Soak Wash cannot be selected for the Wool mend- Wash program. wool. 5 ・The water level and the amount of detergent to be used will be shown and water will be supplied. 7 8 WashingProm 14 Delay Delay AditonalFucOps Start Start (Reservation) Wash is used to The hours to be The time on the 1 (Reservation) Wash delay the finishing time delayed can be set by the user accordingly. display is the finishing time not the start time. of the operation. , Press the POWER button to turn power on. AUTO POWER OFF 2 Press the PROGRAM button to select the washing program. Select the program for laundry on the Control This method will not work in Wool Program. 3 Press the Delay Start (RESERVATION) button delayed washing is to be to set the time when the completed. The time changes as following (6→9→15→ 6Hours). 4 Add the panel. detergent. The order appropriate quantity of detergent marked next to the water level of WATER-DETERGENT. When the lid is open the machine will not operate, and alarm signal will remind you to close the lid 5 Add the laundry and press the START/PAUSE button. When you press the START/PAUSE button the blink. 6 an Close the lid. Water will be Finish The wash to light will supplied for 2 minutes after the start of the supplement the water the laundry has absorbed. washing will be finished according to the delayed time. Note If the lid is open, the machine will not work, and To select washing program, spinning time, (RESERVATION) an alarm water level button and select the desired or option. signal will alarm to remind you to close the lid. hot/cold manually, press the Delay Start Then press the START/PAUSE button. laundry cannot be taken out immediately after the wash program ends, it is better to spinning program (The laundry will be wrinkled if left for a long time after spinning.) When the . omit the 15 Option Washing When you 1 only need the Wash, Wash/Rinse or Rinse these cycles, Press the AUTO OFF (Power) button to turn power can be set manually AditonalFucOps on. AUTO POWER OFF 2 Wash , Wash+Rinse Rinse , Rinse+Spin , , Press the PROCESS button until above light is on. ( refer to p11) When you want to washing tub drains Spin only options Option Washing only drain, wait until the water in completely and then, turn off the the power. 3 Press the WATER LEVEL level of laundry. automatically. amount button, Add the 5 Press the START/PAUSE button. 6 Add the into the detergent control the water anything, level according to washing to tub. and close the lid. Note ? Wash, Wash/Rinse When a not be drained has drained ? ? If only Rinse only option is selected, after the wash is completed the water will press the SPIN button and wait until the water in the tub Then press the START/PAUSE button off, If you wish to drain the water, completely. If you do not or specify the water level, . then Medium will be Rinse is selected, the process will start from Water automatically Supply. the it is set the LARGE water (refer 4 laundry to If you do not choose selected. p10) 16 O AditonalFucOps ther Useful Functions Child Lock Function If you want to lock all the use the child lock keys to prevent all the setting from being changed by a child, you can option. How to Lock 1 Press the POWER button. Turn Power on. AUTO POWER OFF 2 Press the START/PAUSE button to start washing. After all 3 washing conditions are set Press both the PROCESS button and the PROGRAM button according to the manual. simultaneously. During the wash program, all the buttons are locked until washing is completed or it is child- lock function is deactivated manually. How to Unlock If you want to unlock during wash, press both the PROCESS and the PROGRAM button simultaneously again. Note In child-Lock Mute mode, all process light will blink. Option If you want to use the washing machine without alarm signal sounds, press both the WATER LEVEL and PROCESS buttons simultaneously. To make buzzer time. work, press both the WATER LEVEL and PROCESS buttons simultaneously one more 17 and Placing 1 Leveling Place the machine on a flat and firm surface which allows proper clearance. We suggest a minimum clearance of 2cm right side and left sides of the machine for ease of more than 10cm installation. At the rear, a minimum clearance of 10cm is more than suggested. 2cm more than 2cm 2 Check that the machine is level Open the lid and look from above to same as see Top view of the machine if it is shown. 3 Leveling the machine Lift the front of the washing machine and twist Adjustable Leg until the washing machine is placed evenly. the Adjustable legs ※ Installing the Anti-Rat Cover (option) The anti-rat cover should be affixed firmly from the back of the washer UP Caution If the power is supplied from a cord extension set outlet device should be positioned so that it is hot or generator, the cord extension exposed to splashing or ingress set or electrical of moisture. portable Introducin 18C Instal ion onnecting Before Water connecting the Water Hose Supply Hose to the water Supply tap, check the hose type and then choose the correct instruction here under. Note that the Water sure may vary from country to country, Make to connect the blue inlet hose to the cold water tap, and the orange inlet hose to Supply Hose supplied the hot water tap Connecting Water Normal 1 Supply Hose to water Type Untighten the tap (Normal tap without thread & screw type inlet hose.) Rubber screw packing Untighten the screw of the connector so that the tap can be placed in the middle. 2 Fixing the connector to screw Connector the tap Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3 Attach the water to the connector Push the water supply hose connects supply hose vertically upwards that the rubber seal within the hose can securely Connector so adhere completely to the tap. Water Supply 4 Fixing the connector of connector and water supply hose Attach the water then 5 tighten it supply hose to the connector and by screwing it to the right. Check the connection of After water supply connecting the hose, open the tap to check for any water leakage. In case of water leakage, close the tap and start again from step 1 hose and the connector Hose 19 Normal 1 Type (Normal tap without thread & Separate Middle connector from Water Supply Separate Middle connector from the Water Supply Hose by pulling the Pressing Rod and the Pressing Handle that is attached to the Water Supply Hose while pressing them. one touch type inlet hose.) Hose Middle Fixed Sticker connector Pressing Handle Pressing Rod Water 2 Loosen the fixed nuts to connect the connector to the Untighten tap can be the screw of the connector Hose tap that the so Supply Rubber placed in the middle. packing screw Fixed sticker Note In case the tap is too large. Guide plate Rubber If the tap diameter is too large or is square, untighten the 4 screws and remove the guide plate. 3 Then follow Fixing packing step1. Connectors to the Tap Connector Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 4 Connector and Middle Connector Fixing Upper Remove the fixed sticker in between the and Middle Connectors. by holding one 5 Tighten the connectors connector and connector to the Connector Upper Middle twist middle Connector right. Fixed sticker Connecting Middle Connector and Water Supply pressing rod of the Water Supply separated from middle connector Step1) and then join it to the middle Connector Middle Connector Hose Press down the Hose which (refer to was Pressing rod connector. Water 6 Check for After water connecting the leakage hose, open the tap to check for any water leakage. If the connection leaks, close the tap and start again from step 1. If you skip step 1, water leakage may occur. Supply Hose Pressing handle Instal ion 20 C Instal ion Screw 1 Water onnecting Hose Type Attach the water Push the water packing Supply supply supply hose up within the hose can so hose to the tap. that the rubber adhere completely to the tap. Water tap Rubber Water 2 Connect the water Connect the tighten 3 After hose supply hose to the tap screwing it to the right. water it by Check supply water to Packing Supply the tap. and then leakage. the hose, connecting leakage. open the tap to check for any water Connecting Water Supply Hose to the machine water supply hose to inlet valve of washing machine, and then lock it by turning the hose connecting part. Connect the the Check to see if there is a rubber seal inside Hose connector the connector. Rubber seal Hose 21 Connecting Drain Hose Before connecting Drain Hose, check your Drain Hose model and choose the correct instructions. Instal ion Pump Model 1 Fit the machine end of the drain hose to the outlet 2 Put the other end of the drain hose of the drain pump and tighten the clamp. over the standpipe or wash tub. Hose Guide Within 50mm 0.9~1.2m Drain Hose Note To prevent siphoning, the drain hose should not extend more than 50mm from the end of the hose The discharge height should be approximately 0.9 1.2m from the floor. ~ Non-Pump Model 1 Before connecting Ensure that the hose clip is set as indicated here. Clip 2 Connect the Elbow Hose Push the elbow hose toward the washing 3 body of the machine. Place the Drain Hose change the direction of the hose, pull change the direction. Repeat Step2. To elbow hose and out the guide. 22 G CarendMitc rounding Method Earth wire should be connected. If the earth wire is not connected, there is caused by the current leakage. Grounding possible a danger of electric shock Method with Ground insert space Terminal If the AC current outlet has a ground terminal, then required. Note that AC power outlet configurations may differ from country separate grounding is to not Ground Terminal country Outlet with Other Method Grounding ground terminal. Burying Copper Plate Connect the Ground Wire Plate and bury it more to a Ground Copper ground. than 75cm in the Ground Wire 75cm Using Ground Ground Wire Copper ground Wire to the socket provided exclusively Grounding. Plate Connect the for Using Short Circuit Breaker If grounding methods described above possible, employed a Ground Wire are not separate circuit breaker should be and installed by a qualified electrician Short-circuit breaker Caution ? ? To prevent a possible explosion, do not connect ground to a gas pipe Do not connect ground to telephone wires or lightning rods. This may be storms ? ? Connecting ground to plastic has no effect Ground wires should be connected when an extension cord is used. dangerous during electrical 23 Cleaning When water supply into the tub is not clean the filter is or clogged with sand), clean the filter in the inlet valve occasionally.(The figure of power cord and water tap may vary according to the country) particles(Such as To Clean the Filter in the Inlet Valve Close the tap before 1 turning off the power. Select both hot/cold and then press the [START/PAUSE] button to remove water from the machine removing the water supply hose pull out the filter. Then use a Turn off the power before pulling out the cord. 4 Replace the filter after cleaning it. completely. After 3 2 brush to clean the filter. Caution ? Before cleaning the filter, the impurities in the water supply hose should be removed. To Clean the Lint Filter 1 Pull out the lint filter from 2 Turn the net inside out the tub in the direction to clean the filter and shown below. rinse it with water. 3 Replace- the filter to the original location. Push the lip of the filter until a pop sound is heard. Note ? If the lint filter is torn To Clean the 1 damaged, purchase a new one from LG service center. Pump casing (for pump model) Unfasten 4 back or screws of the cover. 2 Turn the cap as shown in diagram and unfasten it. Remove as foreign objects pin, button, coin, 3 fasten it. such etc (Bottom view) (Bottom view) Caution ? Check if water leaks after reassembling. (The Rubber Reassemble the cap to the arrow direction and ring is in the cap) CarendMitc 24 C CarendMitc leaning WHEN THERE IS A FEAR OF FREEZING 1 Close the 2 Remove the water which remains in the water 3 Lower the drain hose and drain the water in the bowl and the drain hose water taps and remove the Water Supply Hose. supply. by spinning. IF FROZEN and immerse it in hot water at approx.. 40 ˚C. 1 Remove the water 2 Pour approx.. 2 liters of hot water at approx.. 40 3 Connect the supply and supply hose, water supply hose to drainage of water. Wash Inner-tub ˚C, into the bowl and let it stand for 10 minutes. the water tap and confirm that the washing machine performs the Leave the lid open after washing to allow moisture to evaporate. If you want to clean use a clean soft cloth dampened with liquid detergent, then rinse. (Do the inner-tub not use harsh or Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit sharp objects. Exterior Long gritty cleaners.) Vacations Be sure water be below supply freezing. surface with is shut off at faucets. Drain all water from hoses if weather will SCRUD Scrud is the name given into contact with comes to the waxy build-up that can occur within any washer when the fabric softener This build-up is not brought about by a fault in the machine. detergent. If scrud is allowed to build-up in the machine it smell in your washer. can result in stains on your clothes or an unpleasant If you wish to ? ? ? ? Using fabric Clean use fabric softener the dispenser, do not dispenser as soon as the we recommend. splash or overfill. cycle has finished. Clean your machine regularly Cold increases the chance of this water washing build-up occurring. We recommend a warm or hot wash at regular intervals e.g. approx. every 5th wash. ? Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up CLEANING THE INSIDE OF YOUR WASHER ? ? ? Fill your machine with hot water. Add about two cups of a powder detergent that contains phosphate. Let it rotate for several minutes. Stop the machine, drain the machine and run We do not recommend that you wash clothes the machine through a regular cycle. during this procedure. 25 Troubleshooting Look for your problem below, then check the things we suggest. More often than not, this will give you the answer to your problem. And you'll be able to carry on without having to telephone your service center. Troubleshting WASH PROBLEM Problem residue clothes Lint on or Possible Causes Incorrect What To Do ? sorting Washing too long ? Separate lint producers from lint collectors. Wash small loads for a shorter time than larger loads. ? Detergent on Detergent not dissolving clothes ? ? ? Black spots clothes on of fabric softener Incorrect use Dye transfer Snags, holes, tears, rips or excessive wear Pins, snaps, hooks, sharp buttons, belt buckles, zippers, and sharp objects left in pockets Undiluted chlorine bleach ? ? ? Try using less detergent Use warmer When filling dispenser, Sort whites Wash and Fasten snaps, hooks, buttons, and zippers. Remove any loose brassiere wires. objects in pockets and sharp buttons. (which snag easily) inside out. Remove ? Turn knits ? Check bleach laundry dirty out package instructions for proper amount. Never add undiluted bleach to wash clothes to comes or lightly colored items from dark colors. dry non-colorfast clothes separately ? ? The splash or overfill. directly on clothes. do not Pre-treat stain and rewash. ? ? temperature. Never pour fabric softener ? ? water Try a liquid detergent. Try pre-dissolving the detergent come or allow in contact with undiluted bleach. Water temperature is too cold. Use Stain is not pre- detergent dissolved in water onto stains help shift dirt. Wash stains as soon as possible. The longer they are left the harder they are to remove. treated warmer Brush a water temperature little like collars and cuffs to Washer is overloaded Did you load too much into the machine? Incorrect White clothes are Separate light and sorting better washed heavily separately. soiled items. 26 T roubleshooting Before Troubleshting calling for service check the Error Symptom Water Supply Failure problem against the Message list belows. Check up . . . . Is the water tap shut off? Is the water supply cut off ? Is the tap or water supply hose frozen ? Is the water pressure low or is the filter of the inlet clogged with impurities? valve . Is Hot/Cold selected to Hot when the hose connected is Cold? . Drainage Failure Spin Failure Door(Lid) Open Internal sensing failure Power failure Overflow failure Is the Cold hose connected to Hot? . Is the drain hose . Is the drain hose bent . Is the internal part of the hose or drain pump (only pump model) clogged with impurities? . Check if electric power has gone off. positioned correctly? or placed too high? . Is the laundry evenly balanced? . Is the washing machine placed . Is the lid closed? . Ask for help at the on a flat surface? LG Electronic branch of the Service Center 27 Specification H D W Model WF-S(C/F)5101(~5)PC(H/P),S(C/F)5101(~5)PD(E/F),S(C/F)5111(~5)PC(H/P),S(C/F)5111(~5)PD(E/F) WF-S(C/F)5201(~7)PC(H/P),S(C/F)5201(~7)PD(E/F),S(C/F)5211(~7)PC(H/P),S(C/F)5211(~7)PD(E/F) WF-S(C/F)6101(~5)TC(H/P),S(C/F)6101(~5)TD(E/F),S(C/F)6111(~5)TC(H/P),S(C/F)6111(~5)TD(E/F) WF-S(C/F)6201(~7)TC(H/P),S(C/F)6201(~7)TD(E/F),S(C/F)6211(~7)TC(H/P),S(C/F)6211(~7)TD(E/F) WF-S(C/F)5301(~7)TC(H/P),S(C/F)5311(~7)TD(E/F),S(C/F)5401(~5)TC(H/P),S(C/F)5411(~5)TD(E/F) Size WF-S(C/F)5201(~7),S(C/F)6201(~7),S(C/F)5301(~7): 530(W)x540(D)x850(H) WF-S(C/F)5211(~7),S(C/F)6211(~7),S(C/F)5311(~7): 530(W)x540(D)x900(H) WF-S(C/F)5101(~5),S(C/F)6101(~5),S(C/F)5401(~5): 540(W)x540(D)x850(H) WF-S(C/F)5111(~5),S(C/F)6111(~5),S(C/F)5411(~5): 540(W)x540(D)x890(H) Water tab pressure 30 -800 kPa (0.3 -8 kgf /cm2) our continuing effort to improve the quality of our appliances, changes to the appliance without revising this manual. In it may be necessary to make P/No.: 3828EA3006D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Frequently Answers and Questions
What's the first step in the washing process?
Sort clothes according to amount of soil, color, and lint.
What should be done with zippers and loose brassiere wires before washing?
Close zippers, hook and strings, and remove loose brassiere wires to prevent snagging and damage.
How can stains be pretreated?
Apply a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt.
How much detergent should be used?
The machine automatically detects the quantity of laundry and sets the proper amount of detergent.
What is 'Delay Start' and how is it used?
Delay Start allows you to set a preferred finishing time for the washing cycle. It can be adjusted according to your needs.