advertisement
▼
Scroll to page 2
of 60
Operating Instructions Model No. PV-D4732 / PV-D4732S Initial Setup (Connection) DVD/VCR DECK Basic Operation VCR Operation Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. LSQT0618B (Guía para rápida consulta en español está incluida.) For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 1 2002/05/23, 18:12 For Your Information As an ENERGY STAR® Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR® guidelines for energy efficiency. DVD Operation Connections and Initial Setup Procedures are on pages 12 to 17. Important Safeguards and Precautions FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT INSTALLATION 1 POWER SOURCE CAUTION Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home. 2 POLARIZED OR GROUNDING PLUG As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug. 3 POWER CORD Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic. If an extension cord is used, make sure it also has either a polarized or grounded plug and that the cords can be securely connected. Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician. Overloaded outlets and extension cords are fire hazards and should be avoided. 4 DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat generated during operation. If they are blocked, heat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes or discs. For protection, follow these rules: a. Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface. b. Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided. 5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES Do not place the unit over or near heater or radiator, in direct sunlight, inside closed vehicles, in high temperature [over 104°F (40°C)], or in over 75% humidity. If the unit is suddenly moved from a cold place to a warm one, moisture may condense in the unit and on the tape causing damage. Never subject the unit to vibration, impact, or place it so that the surface is titled as internal parts may be seriously damaged. 6 TO AVOID PERSONAL INJURY • Do not place unsecured equipment on a sloping surface. • Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit. • An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. • Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment. 2 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2 OUTDOOR ANTENNA INSTALLATION 1 SAFE ANTENNA AND CABLE CONNECTION If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. NEC - NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) 2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional. USING THE UNIT If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards. 1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT, unplug the unit and have it inspected by a qualified service technician before use. 3 DURING AN ELECTRICAL STORM During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system. 4 WHEN THE UNIT IS PLUGGED IN • Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside. • Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray. • Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment. 5 USING ACCESSORIES Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards. 6 CLEANING THE UNIT Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts. SERVICE 1 DO NOT SERVICE THIS PRODUCT YOURSELF If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician. 2 IF REPLACEMENT PARTS ARE REQUIRED Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards. 3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacture’s service literature to ensure that the unit is in safe operating condition. 2002/05/23, 18:12 Safety Precautions/Mesures de sécurité WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Avertissement: Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION: UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY INSTRUCTED. WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. CAUTION: LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM. ATTENTION: RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU. (Inside of product) FCC NOTE: This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful. FCC Caution: To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited viewing uses only. FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s authority to operate. Region Management Information: This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc. The Region number for this DECK is 1. 1 3 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 3 2002/05/23, 18:12 Before Using Disc formats supported by this DECK Congratulations on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK. • Date of Purchase • Dealer Purchased From • Dealer Address • Dealer Phone No. • Model No. • Serial No. DECK can play back discs bearing any of the following marks: DVD 3” (8 cm) disc / 5” (12 cm) disc Video CD 3” (8 cm) disc / 5” (12 cm) disc CD 3” (8 cm) disc / 5” (12 cm) disc Discs which cannot be played • • • • DVD with Region No. DVD of PAL system DVD-ROM CDV other than “1” or “ALL” • DVD-R/DVD-RAM • CD-ROM • CD-G Do not try to play Photo CD. Accessories is a registered trademark. Remote Control Disc Handling LSSQ0345 (PV-D4732) LSSQ0352 (PV-D4732S) Handling precautions Batteries 2 “AA” RF Coaxial Cable VJAS0196 To order accessories, call toll free 1-800-332-5368. Loading the Batteries 1) Open cover. • Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion. • Do not write on label side of disc. • Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent. • Be careful not to drop or bend disc. • Do not place more than 1 disc on disc tray. • Do not try to close Disc tray disc tray when disc Disc is not properly placed. • Always store discs in their proper cases when not in use. To clean disc surface With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.) 2) Insert batteries as marked. 3) Close cover. Battery replacement caution • Do not mix old and new batteries. • Do not mix alkaline with manganese batteries. 4 If disc is brought from a cold to a warm environment, moisture may form on the disc Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.) Improper disc storage Discs could be damaged if stored or left in areas: • exposed to direct sunlight. • that are humid or dusty. • near heat (i.e. heater, radiator, etc.). For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 4 2002/05/23, 18:12 Table of Contents DVD / VCR Important Safeguards and Precautions ............................ 2, 3 Before Using ............................................................................ 4 DECK & Cassette Information ........................................... 6 , 7 Location of Controls ....................................................... 8 ~ 10 Displays (On Screen Displays and Multi Function Display) .................... 11 Connections .................................................................. 12 ~ 15 Initial Setup for Basic Connections (Ready to Play) .......... 16, 17 Initial Setup (Connection) VCR Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19 Playback/ Record on a Tape........................................... 20, 21 DVD Basic DVD Operation ...................................................... 22, 23 Basic Operation Timer Recording .............................................................. 24, 25 MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27 Multi-Brand Control Feature ........................................... 28, 29 Tape Operation (Search System) ....................................... 30 ~ 32 Special VCR Features ..................................................... 33, 34 Copying Your Tapes (Dubbing) ......................................................... 35 VCR Operation Disc Operation ............................................................... 36 ~ 40 DVD Operation using On-Screen Displays ................... 41, 42 MP3 Playback Operation....................................................... 43 DVD Lock Feature ................................................................. 44 Settings for DVD Operation .......................................... 45 ~ 47 Language Code List .............................................................. 48 DVD Operation DVD / VCR Warning and Instruction Displays........................................ 49 Before Requesting Service............................................. 50, 51 Limited Warranty ............................................................. 52, 53 Customer Services Directory ............................................... 53 Spanish (Español) Quick Use Guide............................ 54 ~ 59 Index ....................................................................... Back Cover For Your Information 5 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 5 2002/05/23, 18:12 DECK & Cassette Information Head Cleaning Prevent Accidental Tape Erasure Playing older or damaged tapes may eventually cause video heads to become clogged. Video Head Clog Sensor During playback, this screen appears if V I DEO HEADS MAY NEED CLEAN I NG clogging is detected. PLEASE I NSERT HEAD CLEAN I NG CASSETTE To remove screen, OR REFER TO MANUAL press PLAY on the END : PLAY remote or DECK. • Use “dry” type head cleaning cassette only. (Part No. NV-TCL30PT is recommended.) • Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life. • If head clog symptoms persist, contact your nearest Factory Servicenter or authorized Servicenter (see p. 52). Break off the tab to prevent recording. Record Tab Screw driver To record again Cover the hole with cellophane tape. Record/ Playback Time Built-in Head Cleaner A clean video head helps produce a clear picture. So, we have equipped your DECK with a built-in, non-chemical head cleaning system that helps prevent clogging of the video heads. Cleaning is performed each time you load or unload a video cassette. • This feature is preventative only, If your video heads are seriously clogged, consider the use of a chemical non-abrasive head cleaning kit or take your DECK to a Servicenter. Only use tapes with the Tape Speed Setting mark in this DECK. Type of Video Cassette T60 T120 T160 2 Hours SP 2 Hours 40 Minutes (Standard Play) 1 Hour LP 5 Hours 2 Hours 4 Hours (Long Play) 20 Minutes SLP 8 Hours (Super Long Play) 3 Hours 6 Hours Cleaning DECK Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher. Features for a Quality Picture (VCR) Digital Auto Picture Automatically controls the video output signal for less noise depending on the tape condition. Digital Auto Tracking Continuously analyzes the signal and adjusts for optimum picture quality. Manual Tracking Control (to reduce picture noise) Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later. R R R R R R R R V-Lock Control (to reduce picture jitter) In Still mode, CH (TRACKING) / operate as a V-Lock control. 6 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 6 2002/05/23, 18:12 Specifications Input/Output Terminal: Input Terminal: Output Terminal: Operating Temperature: Operating Humidity: Weight: Dimensions: Discs Played (1) DVD-VIDEO Disc (2) Compact Disc (CD-DA, VIDEO CD) Digital Audio Output: Pickup: 120 V AC, 60 Hz Power On: Approx. 32 watts, Power Off: Approx. 4 watts EIA Standard NTSC color 4 rotary heads helical scanning system 1 track (Normal), 2 channel (Hi-Fi Audio Sound) VHF 2 ~ 13, UHF 14 ~ 69 Midband A through I (14 ~ 22), Superband J through W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125 Audio/Video Line Input/Output, RF Input/Output Audio/Video Line Input (Front) S-Video Output (DVD only), Component Video Output (DVD only) Audio Output 2 (L), (R) 5 °C ~ 40 °C (41 °F ~ 104 °F) 10 % ~ 75 % 6.9 kg (15.2 lbs). 430 (W) x 118 (H) x 364 (D) mm 16-15/16” (W) x 4-5/8” (H) x 14-5/16” (D) inch Initial Setup (Connection) Power Source: Power Consumption: Video Signal: Video Recording System: Audio Track: Tuner: Broadcast Channels: CABLE Channels: 5” (12 cm) single-sided single-layer 5” (12 cm) single-sided double-layer 5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side) 5” (12 cm) disc 3” (8 cm) disc Digital Optical Connector Wavelength: 655 nm (DVD), 790 nm (Video CD/CD) Laser power: CLASS II Note: • Designs and specifications are subject to change without notice. Definition of Terms (DVD) Angle: Some DVD discs feature scenes simultaneously shot from different angles. The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.) Chapter Number: Titles are subdivided into numbered sections. You can quickly search for a favorite scene using these numbers. DVD: A high-density optical disc on which high-quality pictures and sound have been digitally recorded. DVD incorporates new video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality. Playback Control:With Video CD (version 2.0), scenes or information may be selected for viewing or listening from an interactive menu that appears on the TV screen. Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find scenes. (May not work with some discs.) Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be quickly located. Video CD: CD containing picture and sound with same quality level as video tape. This DECK also supports Video CDs with playback control (version 2.0). This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. 7 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 7 2002/05/23, 18:12 Location of Controls Bold: VCR Function Bold Italic: VCR and DVD Functions Remote Control Italic: DVD Function Normal: Others LIGHT EJECT/ OPEN/CLOSE p. 8 pp. 20, 22 TV mode POWER p. 28 VCR mode DVD mode p. 28 p. 28 DSS/CABLE mode INPUT p. 35 p. 28 PLAY FAST FORWARD/SEARCH/ SLOW+ pp. 20, 22 pp. 20, 23 REWIND/SEARCH/ SLOW- PAUSE/STILL pp. 20, 23 pp. 20, 23 VCR/TV STOP p. 21 pp. 20, 22 NUMBER keys ADD/DELETE/ CLEAR pp. 19, 39, 44 RETURN/ SEARCH SURROUND/ ENTER pp. 23, 28 pp. 22, 30 PROGRAM ACTION p. 24 pp. 18, 45 SELECT SKIP SKIP MENU p. 23 p. 38 TITLE SET p. 38 SUB TITLE p. 36 ZOOM ANGLE p. 37 p. 37 DISPLAY AUDIO (SAP/ Hi-Fi) p. 11, 41 pp. 27, 36 CHANNEL / TRACKING/V-LOCK VOLUME +/- pp. 21, 6 p. 28 TAPE POSITION/ AUDIO CONTROL COUNTER RESET p. 34, 40 p. 32 RECORD p. 21 SPEED COMMERCIAL SKIP/ ZERO p. 21 pp. 31, 32 Light Tower Universal Remote Control Light button: When Light button is pressed, (DVD, TV, VCR, PLAY, STOP, REW, FF) buttons will light up for 5 seconds for easy button location. If no button is pressed in 5 seconds, the light goes out to conserve the battery. EJECT button: When this button is pressed in VCR mode, the tape is ejected. This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes. 8 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 8 2002/05/23, 18:12 c: DVD Function mal: Others FrontView View DECK Front ofof DECK If the disc cannot be removed... First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. Initial Setup (Connection) Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Normal: Others STOP/EJECT p. 20 FAST FORWARD/SEARCH p. 20 PLAY p. 20 Over 2 inches REWIND/SEARCH p. 20 POWER Cassette Compartment Disc Tray Multi Function Display Audio/Video Input Connector 2 (LINE 2) p. 35 OPEN/CLOSE p. 11 p. 22 Remote Sensor PAUSE p. 23 CHANNEL / TRACKING/V-LOCK PLAY pp. 21, 6 p. 22 SKIP SKIP VCR/TV p. 21 p. 23 STOP REC p. 22 p. 21 For assistance, call 1-800-211-PANA(7262) PV-D4732S P1-25 (2nd) [LSQT0618B].p65 9 2002/05/23, 18:12 9 Location of Controls (continued) Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Rear View of DECK AC Power Plug • While plugged into an AC outlet, this DECK consumes 4 W of electrical power in off mode. VHF/UHF Antenna Output Terminal p.12 Component Video Output Connector (Y, PB, PR) (DVD Only) p. 13 Video Output Connector p. 12 SELECT SW (DVD Only) p. 13 DVD OUTPUT DIGITAL AUDIO OUT OPTICAL Video Input Connector p. 35 COMPONENT OUT VIDEO OUT SEE MANUAL (PCM/BITSTREAM) IN1 IN FROM ANT. VIDEO Y OUT PB S-VIDEO OUT SELECT PR Optical Digital Audio Output Connector (DVD Only) p. 15 VHF/UHF Antenna Input Terminal p. 12 • L AUDIO2 R S-Video Out Connector (DVD Only) p. 10, 13 L AUDIO1 R • VHF/UHF OUT TO TV Audio Input Connector (L/R) p. 35 Audio Output 2 Connector (L/R) p. 13 Audio Output 1 Connector (L/R) p. 12 The following table shows the status of the output jacks when in VCR or DVD mode. VCR YES DVD YES Note 10 • Component Video Output S-VIDEO OUT N/A N/A ➛ Video Output Audio Out 1 Audio Out 2 YES SELECT SW (Switchable)➛YES PROG functions on the remote are not available when using Component Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 10 2002/05/23, 18:12 Displays (On Screen & Multi Function) On Screen Displays (VCR) CH 0 8 Initial Setup (Connection) Function & Channel Displays Blank Tape/ No Video Signal Indications When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears. Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue. Function Status VCR Status & Clock Displays To display or remove overlay at right, Rec Time Remaining ➛ press DISPLAY. (OTR mode only, see p. 21.) Current Time Channel CH 02 REC 1 2 : 0 0AM -0 : 1 2 : 3 4 0 : 25 SP STEREO SAP MONO Counter Tape Speed (See p. 6.) Broadcast Audio Being Received (See p. 26.) Multi Function Display VCR Indicator Hi-Fi Indicator Timer Indicator Lights up when the VCR/TV selector is set to VCR. Lights up when Hi-Fi audio is monitored in Play mode. Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming. Power Indicator Lights up when power is on. VCR mode Indicator Lights up when DECK is VCR mode. • VCR VCR Hi-Fi TIMER • VCR REC A M DVD mode Indicator DVD • Lights up when DECK is DVD mode. ANGLE • VCR REC Indicator Lights up during recording. Clock/ Status/ Channel/ Speed Display AM ANGLE Indicator Displays the current time. Briefly displays VCR status when a function button is pressed. Briefly displays the channel number, or “L1” or “L2” when a channel or line input is selected. Briefly displays the recording speed when SPEED is pressed. Lights up before noon. PM is not displayed. Lights up when a scene recorded at different angles is detected. See p. 37. (DVD only). 11 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 11 2002/05/23, 18:12 Connections Basic Connections • If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound. • You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK. • Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable b (not supplied) as shown in the figure below. ■ DSS Receiver DECK ■ DECK TV ■ Cable Box TV DECK TV Antenna or Cable DSS Receiver IN IN IN OUT Cable Box OUT or 1 Disconnect antenna or cable from TV and connect to DECK. 2 Connect DECK to TV with RF Coaxial Cable. a DVD/VCR DECK RF COAXIAL CABLE TV OUT IN 1 IN FROM ANT. VIDEO VHF/ UHF L VHF/UHF AUDIO OUT TO TV AUDIO IN VIDEO L IN R R b AV CABLE (not supplied) WARNING When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals. Note to CABLE system installer This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 12 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 12 2002/05/23, 18:12 Other Connections You Can IN 1 OUT IN FROM ANT. IN Cable Box VHF/UHF OUT TO TV IN OUT VHF/ UHF R L ANT or CATV IN IN 1 OUT Cable Box IN FROM ANT. OUT VHF/UHF OUT TO TV 2-Way Splitter Cable Box OUT 1 OUT 2 IN OUT A/B Switch IN 1 IN 2 • record scrambled channels. OUT AUDIO VIDEO ■ Connect With Two Cable Boxes DVD/VCR DECK • view any (including scrambled) channel. Initial Setup (Connection) ■ With a Cable Box (DECK Cable Box TV) DVD/VCR DECK ANT or CATV TV You Cannot • use Remote Control to select channels without using Multi-brand control feature. You Can You Cannot • record and view both scrambled and unscrambled channels if additional TV equipment is added. IN OUT This connection R AUDIO requires: two L converter boxes, VIDEO an A/B switch, VHF/ UHF and a 2-way splitter. • view channel other than the one selected for any type of recording. • do a Timer recording of a channel unless you select it on the Cable Box. Connections For DVD Only 1 Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or S-VIDEO mode). 2 If your TV has COMPONENT VIDEO INPUT, set SELECT SW to COMPONENT VIDEO OUT. If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, set SELECT SW to S-VIDEO OUT. Note • The picture will not be displayed if the SELECT SW is not set to the correct video output. 3 When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN. Notes • You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV. • PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG. DVD/VCR DECK DVD OUTPUT TV COMPONENT VIDEOOUT AUDIOOUT2 Y IN IN IN Y L PB R From DECK’s A/V OUTPUT AUDIO P L B PR S-VIDEO OUT SELECT R PR VIDEO S-VIDEO IN or PV-D4732S P1-25 (2nd) [LSQT0618B].p65 13 13 2002/05/23, 18:12 Connections (continued) Audio Connections Ready Checklist Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables. ■ DECK Amplifier Speaker DVD/VCR DECK AUDIO OUT2 Speaker Amplifier Speaker AUDIO IN R L L R Enjoying digital audio output from the digital audio output connector Notes on audio output from the optical digital audio output connector Linear PCM (48/96 kHz 16/20/24bit) dts MPEG 1 Linear PCM Optical digital audio output from connector Dolby Digital bitstream (1-5.1 ch) or OFF (no output)*1 Linear PCM (2ch) (48 kHz sampling/16 bit only)*2 or no output*1 Bitstream or no output*1 PCM (44.1 kHz sampling) Linear PCM (44.1 kHz sampling) MP3 Linear PCM (It depends on the MP3 file) Disc Sound recording format DVD Dolby Digital Video CD CD MP3 *1 The type of audio output from the connector can be selected by the Settings for DVD Operation. (See p. 46.) *2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output from the DECK’s optical digital audio output connector. For your reference: • Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc. • Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit. • If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer. Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved. 14 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 14 2002/05/23, 18:12 ■ DECK Amplifier Speaker or dts (digital theater systems) Decoder Amplifier Initial Setup (Connection) DECK Dolby Digital Decoder Speaker When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or dts decoder is used.] Notes on connecting an optical digital audio cable (optional) • Firmly connect the cable to the connector. Surround Speaker Surround Speaker Center Speaker DVD/VCR DECK Decoder with Dolby Digital dts processing Front (optional) Speaker Front Speaker OPTICAL To Optical Digital Audio Input Connector Amplifier Subwoofer Optical Digital Audio Cable (optional) Caution for optical digital audio output connector: • When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF” at “Dolby Digital” and “OFF” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT” (see p. 46). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers. • When a dts decoder is connected, please select “Bitstream” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT”. If “OFF” is selected, there will be no sound. (See p. 46). • Video CDs and CDs can be played as usual. Note: • Some dts decoders which do not support DVD-dts interface may not work properly with DECK. 15 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 15 2002/05/23, 18:12 Initial Setup for Basic Connections (Ready to Play) Before doing Initial Setup 1 Turn TV on. 2 See connections a RF Coaxial Cable Connection and b AV Cable Connection on p. 12. <RF Coaxial Cable Connection> Set TV to channel 3. <AV Cable Connection> Set TV to VIDEO. 3 [DECK ➛ TV] • Go to “Doing Initial Setup (Ready to Play).” (See below.) [Cable Box ➛ DECK ➛ TV], [DSS ➛ DECK ➛ TV] • Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel in your time zone. • If you use a DSS Receiver, it must be turned off. Doing Initial Setup (Ready to Play) 1 2 Press VCR on remote for VCR mode. Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts. • If screen below does not appear, check DECK - TV connection and, if TV is tuned to channel 3, try switching it to channel 4. • To change VCR’s output channel, please refer to “VCR’s Output Channel” on p. 19. Plugging the AC Power Plug into an AC outlet CH AUTO SET PROCEEDING CANCEL : STOP AUTO CLOCK SET PROCEEDING CANCEL : STOP 16 Continued on next page... For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 16 2002/05/23, 18:12 dy to Play) *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Settings are made automatically. When setup is done, this screen appears. 9 / 29 / 2002 SUN 2 : 20PM DST : ON SETT I NG : CH 10 AUTO CLOCK SET COMPLETED If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock. See below. Initial Setup (Connection) 3 AUTO CLOCK SET IS I NCOMPLETE PLEASE SET CLOCK BY PRESSING ACT I ON KEY ACTION Manual Clock Set SELECT If Auto Clock Set was incomplete. SET 1 Press ACTION* on remote to display CLOCK screen. SET CLOCK : 1/ / DST : ON ----------------------- SELE CT MONTH SELECT : SET :SET EXIT : ACT I ON 2 Press to select the month and SET to set. In the same manner, select and set the date, year, time, and DST (Daylight Saving Time). SET CLOCK 9 / 29 / 2002 SUN 2:20PM DST : ON ----------------------SET COMPLETED SET : SET START : ACT I ON 3 BACK : Press ACTION to start clock and exit. 17 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 17 2002/05/23, 18:12 Reset Language, Channels, Clock 1 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 VCR’s • PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGAM. SELECT : SET:SET EXIT : ACTION 2 Language Channels 1) Press to select language item. 1) Press to select “SET UP CHANNEL,” and press SET. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET:SET EXIT : ACTION SELECT : SET : SET EXIT : ACTION 2) Press SET repeatedly. MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL LANGUE/LANGUAGE:ESPAÑOL CANAL DE SALIDA : 3 2) Press to select “ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”) 1) Press to select “SET CLOCK,” and press SET. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET : SET EXIT : ACTION 2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”) SET CLOCK SET UP CHANNEL ANTENNA : CABLE AUTO SET WEAK S I GNAL D I SPLAY : OFF CABLE / DSS BOX SET UP VCR Plus+ CH SET UP ELEGIR : FIJAR : SET SALIR : ACTION For Spanish MENU REGLAGE MAGNETOSCOPE REGLAGE HORLOGE REGLAGE CANAL LANGUAGE/IDIOMA:FRANÇAIS CA SORTIE : 3 SELECT : SET : SET EXIT : ACT I ON to select 3) Press “AUTO SET,” then press SET. SEL. : REGLER:SET QUITTER : ACTION • If you use a Cable Box, set it to the PBS channel in your time zone. For French MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 AUTO CLOCK SET MANU NUAL T I ME ZONE ADJUST : 0 SELECT : EXIT : ACT I ON CH AUTO SET PROCEEDING CANCEL : STOP For English 3) Press ACTION to exit. • After Channel Auto Set is finished, Auto Clock Set will be performed. SET : SET (“TIME ZONE ADJUST” appears only when auto clock is set.) SET CLOCK 9 / 30 / 2002 SUN 12:00PM DST : ON ----------------------SELECT HOUR OUR SELECT : SET : SET EXIT : ACT I ON SELECT : SET:SET EXIT : ACTION 18 Clock BACK : and to 3) Press select, then set the date, time, and DST (Daylight Saving Time). 4) Press ACTION to start Clock and exit this mode. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 18 2002/05/23, 18:12 k VCR’s Output Channel *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Time Zone Adjust SELECT : SET : SET EXIT : ACTION NUMBER keys 1) Press to select “VCR’S OUTPUT CH.,” and press SET. ACTION ADD/DLT MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT SET SELECT : SET : SET EXIT : ACTION CH 2) Press to select “TIME ZONE ADJUST,” / 2) Press SET. I F YOU PRESS ACT I ON KEY, VCR’ S OUTPUT CH SW I TCHES TO CH 4. SET CLOCK AUTO CLOCK SET MANUAL T I ME ZONE ADJUST : 0 3) Press ACTION. SELECT : EXIT : ACT I ON Basic Operation MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 VCR VCR’s Output Channel (Only when Auto Clock is set.) 1) Press to select “SET CLOCK,” and press SET. POWER SET : SET Add or Delete a Channel To add channel: Select channel with NUMBER keys and press ADD/DLT. CHANNEL 08 ADDED and press SET to subtract or add hour(s) as necessary. PLEASE TUNE YOUR TV TO CH 4. After 3 seconds 3) Press ACTION twice. • “TIME ZONE ADJUST” returns to “0” if clock is set manually. To delete channel: Select channel with CH / or NUMBER keys and press ADD/DLT. CHANNEL 08 DELE TED MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:4 SELECT : SET : SET EXIT : ACTION • To Make Corrections, repeat steps 1) ~ 3). DST (Daylight Saving Time) DECK auto adjusts clock for DST. (p. 17.) Spring (First Sunday in April) DST:ON ➛ Sets clock ahead one hour. Autumn (Last Sunday in October) DST:ON ➛ Turns clock back one hour. • If your area does not observe Daylight Saving Time, select DST:OFF. • Keep these time changes in mind when programming DECK for timer recordings. 19 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 19 2002/05/23, 18:12 Playback/ Record on a Tape EJECT Ready Checklist DVD All connections are made (pp. 12 ~ 15). TV and DECK are plugged in. TV is on and tuned to CH3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.) PLAY FF/SLOW+ PAUSE/ STILL REW/SLOWVCR/TV STOP Playback a Tape 1 Insert a tape. 2 Press PLAY* to play a tape. • DECK power comes on. The VCR mode and “VCR” indicator light up on Multi Function Display. • If tape has no rec. tab (p. 6), auto play begins. Special Features During Play Forward/Reverse Scene Search ➛ Press FF/SLOW+ or REW/SLOW-. ➛ Press PLAY to release. After search has begun, each additional press of FF or REW changes speed as shown below. [SLP] : Approx. 21X ↔ Approx. 9X [LP] : Approx. 9X ↔ Approx. 7X [SP] : Approx. 7X ↔ Approx. 3X If at 21X, 9X, or 7X speed the picture is interrupted, change speed to 9X, 7X, or 3X. Notes • Picture interruption may occur with some TVs. • FF and REW search speed may vary depending on current tape position. Still (Freeze) Picture ➛ Press PAUSE/STILL. ➛ Press PLAY to release. Frame by Frame Picture ➛ Press PAUSE/STILL in Still mode. ➛ Press PLAY to release. Slow Motion Picture ➛ Press FF/SLOW+ (increase speed) or REW/SLOW- (decrease speed) in Still mode. ➛ Press PLAY to release. 3 / REC SPEED Notes • These features work best in SP or SLP mode. • The sound will be muted. • To reduce picture noise, see “Manual Tracking Control” on p. 6. • After DECK is in Still or Slow mode for 3 minutes, it will switch to Stop mode automatically to protect the tape and the video head. Playback using DECK buttons 2 Press PLAY. 1 Insert a tape. Press STOP to stop a tape. Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape. Press EJECT on remote, or STOP/EJECT on DECK to eject a tape. 20 CH Multi Function Display Press STOP/EJECT to stop and/ or eject a tape. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 20 2002/05/23, 18:12 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Record on a Tape This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use mark. Only tapes tapes with the tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended. Insert a tape with a record tab (p. 6). 1 • DECK power comes on. The VCR mode and “VCR” indicator light up on Multi Function Display. 2 Press CH , or NUMBER keys to select the channel. • For “LINE” input, see p. 35. • If channel is over 100, press 100 key then press the remaining 2 digits. Note Press SPEED to select the record speed (p. 6). 3 SP = Standard Play LP = Long Play SLP = Super Long Play • Speed appears on-screen and on Multi Function Display. 4 Press REC to start recording. 5 Press STOP to stop recording. Basic Operation Remove loose or peeling labels from tapes to prevent tape jam. (The VCR REC indicator lights up on Multi Function Display), • To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording. • You cannot view another channel during recording. One Touch Recording (recording in progress), ➛ Press REC repeatedly to set the recording length ➛ (30 min. ~ 4 hours). • DECK shuts off after the preset record length. Normal Rec 4:00 3:00 0:30 2:00 1:00 1:30 Record one station, watch another, ➛ press VCR/TV (“VCR” goes out on Multi Function Display), ➛ select channels at TV (recording continues). Select Channels at DECK (In STOP or REC. PAUSE mode), ➛ press VCR/TV (“VCR” lights up on Multi Function Display), ➛ select channels at DECK. Record using DECK buttons 1 Insert a tape. VCR/TV 4 Press REC to start Recording. Play a disc while recording a tape. ➛ insert a disc during recording, ➛ press DVD, and then press PLAY. Notes • It is not possible to record from DVD/ Video CD/ CD to VHS tape using DECK. • Watching one channel and recording another is not possible when using Cable Box or DSS Receiver. • After 5 minutes in Pause mode, DECK stops to protect a tape and video heads. PV-D4732S P1-25 (2nd) [LSQT0618B].p65 21 2 Select Channel. Multi Function Display Press STOP/EJECT to stop. 21 2002/05/23, 18:12 Basic DVD Operation Ready Checklist All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier, turn the stereo system’s power on. OPEN/ CLOSE POWER 1 2 3 Press DVD to select DVD mode. • If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.) Press OPEN/CLOSE, and then place a disc into the disc tray. 1 2 DVD PLAY REW/ SLOW- FF/ SLOW+ STOP PAUSE/ STILL NUMBER keys 4 RETURN SKIP SELECT READING <Example> T I TLE MENU SET 10 TITLE If an interactive DVD*1 or a Video CD with playback control*2 is used and TITLE MENU appears, go to step 5. 5 Operation using DECK buttons 3, 7 1 Press • You may also close tray by pressing OPEN/CLOSE. • Data reading time differs with each disc. SKIP MENU 3 Insert a disc. • Hold disc by its edges only (p. 4) with printed side up and use guides to place into tray. Use 1 3”(8 cm) or 2 5” (12 cm) disc. Press PLAY to start playing. Disc tray closes automatically. CLOSE SURROUND 4 Press PLAY. 6 Press STOP. *1 Interactive DVD... May include multiple camera angles, stories, etc. *2 Video CD with playback control... Particular scenes or information can be interactively selected from a menu that appears on the screen. T I TLE MENU Dogs Cas t l es B i r ds Dogs Love r s Press OPEN/CLOSE. POWER 22 Press POWER* on the remote or DECK. Dogs Cas t l es Love r s B i r ds Press or NUMBER keys (see below) to select title, and press SET to play. of the world <Example> Using NUMBER keys starts playing automatically. <Example> 1 digit number 1 ••• 1 2 digit number 12 ••• 10 1 2 3 digit number 123 •••100 1 2 3 Press SKIP | or | to go to next or previous menu screen. • SKIP function not available with all discs. Please refer to disc jacket for operation information. To return to menu (play stops) Press TITLE, MENU, or RETURN. (DVD) Press RETURN. (Video CD) 6 7 Press STOP to stop playing. Press OPEN/CLOSE to eject the disc. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 22 2002/05/23, 18:12 ■ Forward/Reverse Scene Search Press FF/SLOW+ or REW/SLOWduring play. Press PLAY to release. • Starting forward/reverse search during play started from menu on Video CDs may recall menu. • Search speed, slow at first, increases with each additional press of the button up to 5 levels. ■ Forward/Reverse Chapter/Track Skip Press SKIP | or | SKIP during play. Each press skips a chapter (DVD) or track (Video CD/CD). SKIP once midway through a chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track. • Pressing | • Pressing SKIP | or | during play started from menu on Video CDs may recall menu. Current playback position Surround Sound System SURROUND ON SURROUND OFF Press SURROUND to set Surround sound. To cancel, press SURROUND. Note • Surround sound effects is available in DVD mode only. Resume Function DECK memorizes the point where STOP is pressed ( flashes on screen). Press PLAY to resume play from this point. Pressing STOP again or opening the tray cancels RESUME, however, RESUME is not canceled when power is turned off and on. • RESUME works only with discs for which elapsed play time is displayed during play. Basic Operation ps) RN. (DVD) *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Chapter/Track Chapter/Track Chapter/Track Chapter/Track Reverse Skip Forward Skip Auto-Power Off Function Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes. ■ Still Picture or Pause Press PAUSE/STILL during play. Press PLAY to release. • DVD/Video CD : DECK will enter still picture mode. • CD : DECK will enter pause mode. ■ Frame by Frame Picture (DVD/Video CD) Press PAUSE/STILL in still mode. Press PLAY to release. Enjoy Video CDs featuring playback control without using menus (Video CDs only) 1. Do steps 1-4 (previous page). When menu appears, press STOP. 2. Press NUMBER keys to select desired track (play begins). • Check disc for track numbers. • Each press advances picture one frame. • Press “1” to start at beginning of disc. • Hold button down for consecutive frame advance. To Resume Menu use, • Whether pictures are advanced by “FRAME” or Press STOP and press PLAY, then the “FIELD” is selected automatically. (See p. 47) menu will be displayed. Now, go to step 5 (previous page). ■ Slow Motion Picture (DVD/Video CD) Press FF/SLOW+ or REW/SLOWin still mode. Press PLAY to release. • Slow motion speed, slow at first, is increased with each additional press of the button up to 5 levels. • Reverse slow motion is not available for Video CDs. • When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc. PV-D4732S P1-25 (2nd) [LSQT0618B].p65 23 Notes • Please read the disc jacket for operation information. • If a single sided disc is placed in upside down, “PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC” is displayed. • Remove disc and press DECK POWER off when not in use. • Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu. 2002/05/23, 18:12 23 Timer Recording Ready Checklist All connections are made (pp. 12 ~ 15). TV and DECK are plugged in. Clock set correctly. Tape has rec.tab. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for rec time. 1 Press PROG* to display Program. 2 13 SUN --:-- --:-- -- DATE START STOP CH SLP TODAY -----------------------SELE CT START DATE SE SELECT : SET : SET END : PROG Example 1) To set record DATE, to select: press 1~31= one time, or DAILY= MON~ FRI, or WEEKLY= same time each week and press SET. ADD/DLT PROG • See selection order left. Today 14 1 31 12 DAILY WEEKLY (SUN) SELECT / Selection Order 13 POWER WEEKLY (MON) WEEKLY (SAT) SELECT 2) To set remaining items, press to select and press SET to set START/ STOP times, CH(channel) or LINE input (p. 35), and tape speed (SP, LP, SLP). SET Press PROG to end programming. 3 DT 13 ---- START 10 : 00 P -- : --- : --- : -- STOP 12 : 00 P -- : --- : --- : -- CH SPD 02 SP -- --- --- -- CANCEL : ADD / DLT SELECT 1-8 : ENTER : SET EXIT : PROG To Enter More Programs, press to select and press SET to set an unused program number, and then repeat step 2. Or Press PROG to exit. VCR mode Indicator Multi Function Display VCR Hi-Fi TIMER VCR • VCR REC A M DVD • ANGLE • • VCR REC Indicator TIMER Indicator • The “Timer” Indicator lights up on DECK. • You can do Timer Recording with the power on or off. • “TIMER REC WILL START SOON” appears on-screen for 2 minutes before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and “REC” will flash on Multi function Display. 24 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P1-25 (2nd) [LSQT0618B].p65 24 2002/05/23, 18:12 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Review, Replace or Clear Program Contents: (Recording is not in progress) 1 2 Press PROG to display Program List. DT START STOP 7 9 : 00A 12 : 00A 8 10 : 00P 12 : 00P 10 8 : 00P 9 : 00P 9 : 00P 10 : 00P SU CANCEL SELECT ENTER EXIT 3 CH SPD 08 SP 02 SP 10 SP L1 LP : ADD / DLT 1-8 : : SET : PROG Press to select number and press SET to display. To cancel a Timer Recording in progress... Hold down STOP on VCR mode for a few seconds to cancel the Timer Recording. (The “TIMER” Indicator goes out on Multi Function Display.) • Any future daily or weekly recording will be performed as programmed. To Replace program... DATE START STOP CH 7 SUN 9:00A 12:00A 08 SP TODAY Repeat Step 2 (p. 24) to set new programs. ---------------------------------------SELE CT START DATE SELECT SET END : : SET : PROG BACK : DT START STOP -- -- : -- -- : -8 10 : 00P 12 : 00P 10 8 : 00P 9 : 00P SU 9 : 00P 10 : 00P CANCEL SELECT ENTER EXIT 4 CH SPD -- -02 SP 10 SP L1 LP VCR Operation or To Clear program... Press ADD/DLT. : ADD / DLT 1-8 : : SET : PROG Press PROG to end the programming. Notes • If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box intput channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on. • 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode. • If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs. • If the start time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed. Important notes when using DSS Receiver • When recording programs via DSS Receiver, DSS Receiver must be left on. • When recording programs via an antenna or cable, DSS Receiver must be turned off. 25 PV-D4732S P1-25 (2nd) [LSQT0618B].p65 25 2002/05/23, 18:13 MTS Broadcast/ VHS Hi-Fi Stereo System Connection Make the Audio/Video Connection as shown on pp. 12 ~ 15. • You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV. Receivable Broadcast Types The following are possible audio broadcast types and onscreen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow. To display the broadcast signal being received, ➛ press DISPLAY*. MTS Stereo and SAP broadcast Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode. STOP 1 2 : 0 0AM STEREO SAP MONO CH 02 0 : 00 : 00 SP DISPLAY MTS Stereo broadcast Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode. AUDIO STOP 1 2 : 0 0AM CH 02 0 : 00 : 00 SP 1 2 : 0 0AM CH 02 0 : 00 : 00 SP STEREO SAP MONO (SAP/Hi-Fi) • If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results. SAP broadcast Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language. STOP STEREO SAP MONO MONO broadcast Normal monaural sound broadcast. STOP STEREO SAP MONO 26 1 2 : 0 0AM CH 02 0 : 00 : 00 SP ® Equipped with -TV Noise Reduction for true MTS reproduction. ® -TV Noise Reduction is required for good stereo separation and audio ® fidelity. is a registered trademark, ® and is licensed by Technology Licensing. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P26-35 (2nd) [LSQT0618B].p65 26 2002/05/23, 18:13 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Audio Mode for Recording 1 Press AUDIO (SAP/Hi-Fi) to display audio mode. (Display disappears after 5 seconds.) 2 STEREO SAP MONO Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. • Refer to “Receivable Broadcast Types” on p. 26. • Arrow indicates selection. 3 Do a recording. See p. 21. VCR Operation Audio Mode for Playback 1 2 3 Start playback. See p. 20. Press AUDIO (SAP/Hi-Fi) to display audio mode. H I F I : L/R HIFI : L HIFI : R NORMAL • Arrow indicates selection. Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. • Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound. Select “NORMAL” for monaural sound. • Display disappears after 5 seconds. Notes • Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound. • To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14, 15.) • If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio. • Hi-Fi and normal audio playback volume level may differ. 27 PV-D4732S P26-35 (2nd) [LSQT0618B].p65 27 2002/05/23, 18:13 Multi-Brand Control Feature POWER Multi-Brand Control Setup VCR The Remote Control can be set to control some TV and Cable Box/DSS functions. 1 2 DSS/ CABLE Find your TV and Cable Box/DSS Receiver Brand Code Number on the following page. TV DVD Setup for TV control, ➛ hold down TV button, ➛ enter code with NUMBER keys. Setup for Cable or DSS control, ➛ hold down DSS/CABLE button, ➛ enter code with NUMBER keys. • If code number is 100 or greater, ➛ e.g., press 1 - 0 - 2 for 102. 3 NUMBER keys Confirm code entry, ➛ press POWER to turn selected unit on or off. • See table below for controllable functions in each mode. ENTER • Repeat setup after remote battery replacement. • Remote will not control every TV, Cable Box, or DSS made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product. Notes Using Multi-Brand Control After remote is set up, you can select VCR, DVD, TV, or DSS/CABLE for the desired function. Press VCR, DVD, TV, or DSS/CABLE on the remote. (Table below shows available remote buttons for each mode.) Mode Unit DVD/VCR CABLE/ DSS CABLE/ DSS All VOL +/- EJECT/OPEN/CLOSE *, DISPLAY, PLAY, STOP, FF/SLOW+, REW/SLOW-, VCR/TV, PAUSE/STILL, SKIP, AUDIO, CM/ZERO, TAPE POSITION, COUNTER RESET , SPEED, REC POWER, INPUT, NUMBER keys, ENTER, CH / , VOL +/- DVD/VCR TV TV * VOL +/ - POWER, ENTER, NUMBER keys (except 100key), CH / Bold: VCR Function Bold Italic: VCR and DVD Functions Italic: DVD Function Normal: TV, Cable Box or DSS Receiver Notes • Not all functions listed may be controllable. • In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection. 28 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P26-35 (2nd) [LSQT0618B].p65 28 2002/05/23, 18:13 TV Brand Code Numbers Panasonic ....................... 01, Quasar ............................ 01, RCA ....................................... GE ......................................... Zenith .................................... Magnavox .............................. 02 02 03 03 04 05 Sylvania ................................ Sharp ............................... 06, Sony ...................................... Toshiba ................................. Sanyo .................................... Fisher .................................... 05 07 08 09 10 10 JVC ........................................ Hitachi ................................... Mitsubishi ........................ 07, Samsung ............................... Gold Star ................... 15, 16, 11 12 13 14 17 Cable Box Brand Code Numbers Oak Sigma ..................................... 46, 11, 129, 101 Panasonic .................................. 17, 16, 08, 87, 109 Philips ................... 23, 24, 20, 13, 07, 50, 128, 129 Pioneer ...................................................... 06, 05, 12 Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126 Quest ........................................................ 06, 05, 12 Radio Shack ............................... 44, 51, 75, 59, 126 RCA ............................................ 17, 16, 08, 87, 109 Realistic ..................................... 44, 51, 75, 59, 126 Recoton ...................................... 44, 51, 75, 59, 126 Regal ................. 41, 14, 15, 28, 102, 104, 103, 130 Regency .................................................. 28, 29, 130 Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126 Samsung ...................................... 42, 06, 32, 05, 40 Scientific Atlanta ................... 08, 09, 25, 61, 53, 87 Sheritech ............................................................... 27 Signal ............................................................ 26, 112 SL Marx ............. 42, 06, 32, 40, 43, 44, 52, 63, 126 Sprucer ...................................... 17, 16, 08, 87, 109 Standard Components ............... 32, 39, 42, 44, 126 Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06 124, 126 Sylvania .......................................................... 19, 18 Teknika ........................................................... 74, 35 Telecaption .................................................... 77, 127 Teleview ................................. 40, 19, 38, 32, 42, 06 Texscan .......................................................... 19, 18 Tocom ................................... 34, 33, 01, 42, 66, 120 Toshiba ................................................................. 36 Unika ........................... 44, 42, 63, 29, 01, 126, 120 Universal .............................. 52, 43, 44, 63, 42, 126 Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107 Videoway .......................................... 07, 23, 50, 129 Vidtek .................................................................... 64 Zenith ............................................... 07, 23, 50, 129 VCR Operation Archer ......................... 44, 06, 01, 120, 05, 63, 126 Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30 52, 04, 124, 126 Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126 Curtis ..................................... 08, 09, 25, 61, 53, 87 Century ...................................... 44, 51, 75, 59, 126 Cabletenna .................. 29, 09, 01, 63, 120, 44, 126 Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126 Diamond ...................... 29, 09, 01, 63, 120, 44, 126 Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107 Eastern ................................................... 28, 29, 130 Explorer .................................. 08, 09, 25, 61, 53, 87 Gemini ..................................................... 30, 04, 124 General Electric ...................................... 01, 57, 120 General Instruments . 01, 84, 83, 34, 03, 02, 04, 55 65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124 Gerrard ............................................... 44, 51, 75, 59 GC Electronics ............... 44, 42, 63, 29, 30, 52, 04 124, 126 Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130 Hitachi ................................................................... 31 Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66 67, 68, 120, 106, 121, 122, 115, 117, 118, 124 Jasco ...................................................... 30, 04, 124 Macom ................................................................... 31 Magnavox ...................................................... 26, 112 Matsushita ................................. 17, 16, 08, 87, 109 Movietime ...................... 32, 39, 42, 44, 126, 38, 40 Maestro ........................................................... 74, 35 NEC .................................................... 40, 19, 38, 32 NSC .................................................... 40, 19, 38, 32 Novavision ............................. 08, 09, 25, 61, 53, 87 Next Level ........... 01, 84, 83, 34, 03, 02, 04, 55, 65 66, 67, 68, 120, 106, 121, 122 Oak ................................................. 46, 11, 129, 101 DSS Brand Code Numbers Toshiba ....................................................... Hitachi/ Hughes .................................... 91, Primestar .................................................... Drake .......................................................... Magnavox ............................................. 94, Uniden ................................................... 94, 90 99 92 93 95 95 Optimus ................................................ 94, 95 Panasonic ................................................... 96 ProScan ...................................................... 97 RCA ............................................................. 97 SONY .................................................. 98, 105 Important Notes • Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does not respond to the first code, please try the next one. • Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually. PV-D4732S P26-35 (2nd) [LSQT0618B].p65 29 2002/05/23, 18:13 29 Tape Operation Search System For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings. Program End Search Index Search 1 Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number. INDEX SEARCH ENTER INDEX NUMBER :1 USING 1- 9 KEYS FORWARD SEARCH :FF REVERSE SEARCH :REW NEXT :SEARCH EXIT :STOP Locates end point of recording for continuity. 1 Press SEARCH twice to display SEARCH in Stop or Play mode. 2 • To calculate number, see below. SEARCH START : FF Press FF/SLOW+ or REW/SLOW- on the remote to start search. FORWARD SEARCH : FF REVERSE SEARCH : REW EXIT Examples of Program End Search. Fig. 1 Program 1 Fig. 2 3 4 5 6 To go to rec. 6 from rec. 2, enter 4 and press FF. 1 NOTE: 2 3 4 5 6 7 BLANK End Point the current tape position Press SEARCH button Program 1 BLANK FF Program 2 If search exceeds a few seconds in BLANK area. Upon locating end point, ➛ search continues 7 sec. past end point, ➛ tape rewinds to 10 sec. before end point, ➛ tape plays to end point and stops. indicates start points of each recording. Note Note • If Index Search is started very close to an index mark, that index mark may not be counted in the search. 30 Program 2 FF 7 Example 2: BLANK the current tape position Press SEARCH button INDEX 2 INDEX INDEX Program 1 End Point 1 End Point FF Fig. 3 To go to rec. 2 from rec. 4, enter 3 and press REW. Program 2 or BLANK the current tape position Press SEARCH button • To cancel, press PLAY or STOP. To Calculate Index Number Example 1: • To cancel, press PLAY or STOP. :SEARCH INDEX 2 Play begins at search end. To search forward or back 1 index, press FF/SLOW+ or REW/SLOW- on the remote while screen left is displayed (10 sec.). INDEX SEARCH Press FF/SLOW+ on the remote to start PROGRAM END SEARCH. PROGRAM END SEARCH • If Program End Search is started very close to an index mark, that mark may be skipped over. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P26-35 (2nd) [LSQT0618B].p65 30 2002/05/23, 18:13 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Auto Operation Functions Auto Play Insert a tape ➛ Power comes on, ➛ Play starts if there is no record tab (see p. 6). Auto Rewind Play Fast Forward ➛ Tape end ➛ Rewind Play Auto Eject REW/SLOWPLAY (Repeat Play must be off) Play ➛ Tape end ➛ Rewind ➛ Tape ejects if there is no record tab FF/SLOW+ STOP SEARCH Commercial Skip VCR fast forwards (skips) over 1~3 minutes of recorded tape. 1 CM/ZERO VCR Operation NUMBER keys Press CM/ZERO in Play mode. • The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below. PLAY 1st Press 1 min Skip 2nd Press 2 min Skip 3rd Press 3 min Skip • No indication appears on-screen. 31 PV-D4732S P26-35 (2nd) [LSQT0618B].p65 31 2002/05/23, 18:13 Tape Operation (continued) Repeat Play Set to playback a recording over and over. 1 2 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 Press to select “SET UP VCR,” and press SET. SELECT : SET : SET EXIT : ACTION 3 SET UP VCR REPEAT PLAY REMOTE WARN I NG AUTO SHUT-OFF SELECT : END : ACT I ON : OFF : ON : OFF Press to select “REPEAT PLAY,” and press SET to set “ON” or “OFF.” SET: SET • Play repeats at tape end or if unrecorded portion over 30 sec. is detected. 4 Press ACTION twice to return to normal screen. STOP Note ACTION • For repeat play in DVD mode, see page 42. SELECT Zero Search To quickly return to a specified tape location. 1 2 SET Press DISPLAY during play to display Counter. PLAY 1 2 : 0 0AM 0 : 00 : 00 SP DISPLAY Press COUNTER RESET at desired position to reset to “0:00:00”. CM/ZERO COUNTER RESET 3 4 5 Continue to record, playback etc. Press STOP. REW 1 2 : 3 0AM CH 02 0 : 30 : 30 SP STOP 1 2 : 3 1AM CH 02 0 : 00 : 00 SP Press CM/ZERO in Stop mode to start Zero Search. • DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00. 32 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P26-35 (2nd) [LSQT0618B].p65 32 2002/05/23, 18:13 Special VCR Features *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Weak Signal Display Feature When “ON,” picture is displayed regardless of signal strength. 1 2 MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET : SET EXIT : ACTION ACTION SELECT Press ACTION to display MENU. 3 SET UP CHANNEL ANTENNA : CABLE AUTO SET WEAK S I GNAL D I SPLAY:OFF SET SELECT : EXIT : ACT I ON SET: SET Press to select “SET UP CHANNEL,” and press SET. Press to select “WEAK SIGNAL DISPLAY,” and press SET to set “ON” or “OFF.” 4 VCR Lock Feature When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children. Press ACTION twice to return to normal screen. Auto Shut-Off Feature The power shuts off at a preset time. To turn on, hold down REC on DECK in Stop mode with no tape inserted for 7 seconds. (Please ignore “NO CASSETTE” warning.) 1 2 VCR Operation • ON: Picture is displayed regardless of signal condition, and may not always be clearly visible. OFF: Screen turns solid blue when signal is weak or non-existent. • Selecting ON has no effect on connected equipment with blue back feature. Press ACTION to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 Press to select “SET UP VCR,” and press SET. SELECT : SET : SET EXIT : ACTION VCR LOCK ACT I VATED 3 To turn off, repeat above. SET UP VCR REPEAT PLAY REMOTE WARN I NG AUTO SHUT-OFF SELECT : EXIT : ACT I ON VCR LOCK OFF : OFF : ON : OFF SET: SET Press to select “AUTO SHUT-OFF.” Press SET repeatedly to change shutoff time as shown below. 2 Hours OFF • VCR Lock cancels in 24 hours if clock is set. 4 Hours 6 Hours 4 Press ACTION twice to return to normal screen. Note • The shut-off countdown will not function during Play or Record. REC 33 PV-D4732S P26-35 (2nd) [LSQT0618B].p65 33 2002/05/23, 18:13 Special VCR Features (continued) Remote Warning Feature If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV, DSS or CABLE mode. 1 2 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET : SET EXIT : ACTION 3 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. SET UP VCR REPEAT PLAY REMOTE WARN I NG AUTO SHUT-OFF SELECT : EXIT : ACT I ON : OFF : ON : OFF SET: SET INPUT Press to select “SET UP VCR,” and press SET. STOP PAUSE/ STILL ACTION Press to select “REMOTE WARNING,” and press SET to set “ON” or “OFF.” SELECT SET • If “OFF,” remote warning will not appear when invalid key is pressed. 4 TAPE POSITION Press ACTION twice to return to normal screen. REC Tape Position and Tape Status Feature To find out the present tape position and amount of tape remaining. Tape position is displayed for VHS-C type Cassettes, tapes under 30 minute long, and some other tapes, but the position is not correct. 1 Press TAPE POSITION to detect current tape position. DETECTING TAPE POSITION SP R 120 M I N. BEG I N 2 • “DETECTING TAPE POSITION” is displayed only when a cassette is first inserted, and it takes several seconds for correct tape position to appear. • The present tape position indication and amount of tape remaining (according to tape speed) is displayed. • Tape remaining time display may not be precise. END Press TAPE POSITION to return to normal screen. Note This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length. 34 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P26-35 (2nd) [LSQT0618B].p65 34 2002/05/23, 18:13 Copying Your Tapes (Dubbing) Connection VCR/ Camcorder OUT OUT VIDEO AUDIO TV DVD/VCR DECK (Hi-Fi) IN 1 VIDEO IN 2 VIDEO L R L AUDIO1 R Front of DECK IN FROM ANT. VHF/ UHF VHF/UHF OUT TO TV L-AUDIO IN2-R (Audio/Video In Terminals on the front of DECK are available) 1 Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown. 2 Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK. In place of Playing VCR, you can use other equipment, such as a Camcorder. Simply connect the unit’s Audio/Video outputs to DECK. Playing (Source) VCR 1 2 Insert a pre-recorded tape. 3 Press PLAY, then PAUSE/STILL immediately to enter PLAY/PAUSE mode. Recording (Editing) DECK Insert a blank tape with record tab. VCR Operation Press INPUT to set DECK Input mode to LINE for Video Input. (See “Selecting the Input Mode” below.) Press REC, then PAUSE/STILL immediately to enter REC/PAUSE mode. The operation of steps 4 and 5 must be done on the playing and recording VCRs at the same time. 4 5 Press PLAY to start dubbing. Playing VCR starts playback. Press PAUSE/STILL to start dubbing. DECK starts recording. Press STOP to stop dubbing. Press STOP to stop dubbing. To Monitor Dubbing on TV Selecting the Input Mode 1 Turn TV on and tune to the Recording VCR channel (CH 3 or CH 4). 2 Set the VCR/TV Selector on DECK to “VCR.” Method 1: Press INPUT repeatedly. Channel Number ↔ LINE1 ↔ LINE2 Method 2: Press CH / . Display will change as below. 1 3 2 Press LINE2 Note • Dubbing tapes protected with Copy Guard will result in poor quality recordings. LINE1 (CABLE) (TV) 125 or 69 Press • “L1” or “L2” lights up on Multi Function Display (about 4 seconds) when LINE1 or LINE2 is selected. • LINE1: For rear audio/video connection. LINE2: For front audio/video connection. Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement. • Please note that some tapes cannot be dubbed on DECK. Also, it is not possible to dub DVD/ Video CD/ CD to VHS tapes using DECK. 35 PV-D4732S P26-35 (2nd) [LSQT0618B].p65 35 2002/05/23, 18:13 Disc Operation Subtitle Language (DVD only) You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 45.) 1 Press SUB TITLE* in Play mode to display the subtitle selection on-screen. Ready Checklist Please read “Basic DVD Operation” on p. 22. [Subtitle language (No.)] [Audio sound track language (No.)] • Display disappears after 5 seconds. • When no subtitles are offered, “-” will be displayed instead of the language number. 2 Press to select a language. Press (or ) to set. Press to select “ON” or “OFF.” ESP Te amo Number of subtitle language being played back. Notes ENG English FRA French DEU German ITA Italian ESP Spanish NLD Dutch SVE Swedish NOR Norwegian DAN Danish POR Portuguese RUS Russian JPN Japanese CHI Chinese KOR Korean MAL Malay VIE Vietnamese THA Thai • If after several presses of the button the language does not change, language selection is not offered on the disc. • When power is turned on again or disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear. ∗ Audio Soundtrack Language (DVD only) You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 45.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.) 1 AUDIO: 1 ENG Dolby Digital 3/2.1ch Hello SELECT : 2 SET SE T : SET AUDIO: 3 ESP Dolby Digital 3/2.1ch Press AUDIO in Play mode to display the audio selection on-screen. • Display disappears after 5 seconds. Audio attribute 1 type, sampling frequency, bit No. of the disc. Press to select desired language. Hola SELECT : SET SE T : SET Number of the audio soundtrack language being played back. 36 Other • Change the No. by pressing and press SET. , [Audio attribute 1 type, sampling frequency, bit No. of the disc (see p. 46.)] LPCM Dolby Digital dts 16bit 20bit 24bit 1ch - 5.1ch 1ch - 5.1ch 96KHz or 48KHz Linear PCM disc Dolby Digital disc dts disc Notes • If, after several presses of the AUDIO button the language does not change, language selection is not offered on the disc. • When power is turned on again or disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 36 2002/05/23, 18:13 *Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc. Multiple Angle Viewing (DVD only) DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button. 1 Press ANGLE in Play mode to display the angle selection on-screen. ANGLE : 1 ANGLE Indicator Notes SELECT : • The ANGLE Indicator lights up on DECK when a scene recorded at different angles is detected. • The angle number can be set beforehand so that the angle is switched whenever the ANGLE Indicator lights up. SET : SET 2 • Display disappears after 5 seconds. Press to select the desired angle. Number of angle being played back. Vocal Selection for Karaoke Discs (DVD/Video CD) 1 2 Press AUDIO in Play mode to display the audio screen. SELECT : SET SUB TITLE ZOOM ANGLE AUDIO SET : SET • DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF • DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF • Video CD LR L R Picture Zoom (DVD only) You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during DVD playback. DVD Operation SELECT Press (or ) to select as shown below, and press (or ) to set. (DVD only) AUDIO:2 ENG VOCAL VOCAL ON ON Press ZOOM repeatedly to change display as follows. Notes • You can enlarge the center portion of the image to one of 2 magnifications. • The subtitle cannot be enlarged nor can it’s position be changed. • The picture zoom feature does not work with a Video CD. • During picture zoom, “ZOOM1” or “ZOOM2” is displayed on-screen. • Zooming, on some discs, may result in poor picture quality, or may not ■ Use the , , and buttons to move the position operate at all. up, down, left and right. 37 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 37 2002/05/23, 18:13 Disc Operation (continued) Title Menu (DVD only) Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.) 1 T I TLE MENU Dogs Cas t l es Love r s B i r ds Press TITLE* in Play mode to display the title screen. <Example> 2 T I TLE MENU Dogs Cas t l es Love r s B i r ds B i rds of the world Press or NUMBER keys to select a title, and press SET or PLAY to start playing. PLAY • “Pressing SET or PLAY” is not necessary when using NUMBER keys. STOP NUMBER keys <Example> CLEAR ACTION SELECT DVD Menu (DVD only) DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc. Although contents and operation may vary, the following steps show basic steps for using the menu. 1 DVD MENU 1 . SUBT I TLE 2 . AUD I O MENU SET Press MENU in Play mode to display DVD MENU. TITLE 3 . ANGLE <Example> 2 DVD MENU 1 . SUBT I TLE 2 . AUD I O 3 . ANGLE <Example> 38 Press or NUMBER keys to select an item, and press SET or PLAY to perform. • “Pressing SET or PLAY” is not necessary when using NUMBER keys. Repeat step 2 if there is more than one menu. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 38 2002/05/23, 18:13 *Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Program Play (Video CD/CD) Ready Checklist DECK is in DVD mode, press DVD. Video CD or CD is inserted. You can program specific tracks and order of play. 1 2 Press ACTION to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I E LD TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 PLAY MODE SELECT SET END 3 PROGRAM PLAY RANDOM PLAY 1 2 3 4 5 : : SET : ACTION PROGRAM PLAY DISC PROGRAM 6 11 16 5 8 7 12 17 15 6 8 13 18 1 13 9 14 19 3 2 10 15 20 2 CLEAR LAST CLEAR ALL SELECT : SET : SET END : ACTION Press to select “PLAY MODE,” and press SET to display. 1 2 START Press to select a track number (Track numbers on disc are displayed.), and press SET. Do operation steps 1 through 5 at left on this page. Press DISPLAY to display Disc Information screen. (Disc Information Screen) TRACK PBC Press to select “PROGRAM PLAY,” and press SET to display. PLAY MODE SELECT SET END 4 : : SET : ACTION Program Repeat Play (Video CD/CD) SET 3 4 : 1 : OFF : SET VIDEO CD 1 : 35 : 12 NEXT : DISPLAY Press DISPLAY to display DECK Information screen. Press SET to enter Select mode. “REPEAT OFF” will flash. (DECK Information Screen) PLAY REPEAT OFF PROGRAM PLAY • Repeat step 4 to select another track. • The selected track is added on the right side. 5 1 6 2 7 3 8 4 9 5 10 PROGRAM PLAY DISC PROGRAM 11 16 5 8 12 17 15 6 13 18 1 13 14 19 3 2 15 20 2 START SET 5 : SET Press to select “DISC REPEAT.” (DECK Information Screen) PLAY DISC REPEAT PROGRAM PLAY • To cancel, press STOP during play, then press CLEAR. SELECT : SET : SET Notes • Up to 15 tracks can be programmed. • “ ” or “ ” (depending on disc) indicates additional PROGRAM PLAY screen. Press for next or previous screen. • To clear the last program one by one Press to move to “CLEAR LAST” and press SET. (Pressing CLEAR on remote control also clears last program.) • To clear all programs Press to move to “CLEAR ALL” and press SET. (Programs are also cleared when the power is turned off or the disc is removed.) END : DISPLAY 6 END : DISPLAY DVD Operation CLEAR LAST CLEAR ALL SELECT : SET : SET END : ACTION Press to select “START,” and press SET to start play of programs in the sequence selected. Press SET to set mode. (“DISC REPEAT” will stop flashing.) To cancel, select “REPEAT OFF” in step 5, then press SET. 39 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 39 2002/05/23, 18:13 Disc Operation (continued) Random Play (Video CD/CD) Tracks are played in a random order. 1 2 Press ACTION* to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I E LD TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 PLAY MODE SELECT SET END 3 : : SET : ACTION PLAY MODE PROGRAM PLAY RANDOM PLAY SELECT SET END : : SET : ACTION Pess to select “PLAY MODE,” and press SET to display. Ready Checklist DECK is in DVD mode, press DVD. *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Press to select “RANDOM PLAY,” and press SET to begin random play. STOP • To cancel, press STOP during play, then press CLEAR. CLEAR ACTION SELECT SET AUDIO CONTROL Setting the Sound Output Level Audio recorded on a DVD or Video CD often incorporates a dynamic range of sound. This means that, when compared to a music CD, etc., the average volume is generally lower and the peaks may be higher. This unit can be set so that the average volume is increased automatically. Press AUDIO CONTROL repeatedly to change “ON” ↔ “OFF.” • “ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when press AUDIO CONTROL. Audio Control “OFF” Volume level is low. DVD /Video CD Audio Control “ON” Volume level is increased automatically when played back. Music CD • “ON” is set ..... When a DVD or Video CD is played back, the average volume is increased. • “OFF” is set .... The volume level recorded on the disc is played back just as it is. Notes • When audio equipment is connected, setting the Sound Output level to “OFF” is recommended. • If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.” 40 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 40 2002/05/23, 18:13 DVD Operation using On-Screen Displays When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode). 1 Ready Checklist DECK is in DVD mode, press DVD. Press DISPLAY in Play or Stop mode to display “On-Screen Displays.” • Each press of DISPLAY changes the on-screen display as follows. (refer to p. 42.) Selected disc information Selected DECK information Normal Screen Note DISPLAY button does not function while DVD TITLE MENU is displayed. 2 Press (or ) to select an item, and press SET. 3 Press to select the setting, and press SET. NUMBER keys CLEAR SELECT SET <Example of DVD> T I TLE : 12 CHAPTER : 11 T I TLE : 12 CHAPTER : 24 SELECT : SET : SET DVD 0 : 12 : 34 NEXT : DISPLAY NEXT : DISPLAY To make corrections, press and SET repeatedly to move to the error, then correct. • Pressing is effective for elapsing time <Example of Video CD> instead of the above TRACK : 12 VIDEO CD buttons. Press PBC : OFF 0 : 12 : 34 repeatedly to delete the TRACK : 17 VIDEO CD error, then correct. PBC : OFF 0 : 12 : 34 SET : SET SET : SET NEXT : DISPLAY NEXT : DISPLAY DISPLAY • For some functions the setting will be registered immediately without pressing SET. • When numbers are displayed (e.g. title number), NUMBER keys are also available. To return to normal screen, press CLEAR or DISPLAY repeatedly. DVD Operation SELECT : SET : SET DVD 0 : 12 : 34 Notes • When DISPLAY button is pressed during playback of a Video CD with Playback control, NUMBER keys are not available on the displayed screen. In this case, press DISPLAY again to remove the displayed screen. • When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc. 41 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 41 2002/05/23, 18:13 DVD Operation using On-Screen Displays (continued) Detailed Descriptions of each On-Screen Display ■ Disc information screen (for DVD) 1 2 1. TITLE No. * or NUMBER keys, and press SET. • Change the No. by pressing T I TLE : 1 CHAPTER : 12 DVD 1 : 12 : 55 3 4 2. Chapter No. or NUMBER keys, and press SET. • Change the No. by pressing 3. Disc currently being played 4. Elapsed playing time SELECT : SET : SET NEXT : DISPLAY The screen may be changed by selecting the elapsed time. • Change the elapsed time by pressing NUMBER keys . e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45. • This function does not work with some discs. ■ Disc information screen (for Video CD/ CD) A. Track No. or NUMBER keys, and press SET. • Change the No. by pressing B. Playback control ON/OFF A B [Video CD with playback control only] ON Video CD menu play is displayed. OFF Video CD menu play is cleared. TRACK PBC : 1 : OFF VIDEO CD 1 : 35 : 12 C D C. Disc currently being played Video CD CD SET D. Elapsed playing time : SET NEXT : DISPLAY Note • Track No. and the elapsed playing time are not displayed during play started from menu of Video CDs with playback control. appears on the screen while a button is being operated, it means that the corresponding • When operation is prohibited by DECK or the disc. ■ DECK information screen (for DECK) • Change the desired mode during play by pressing , and press SET. a PLAY CHAPTER REPEAT a. Repeat Play DVD CHAPTER REPEAT TITLE REPEAT REPEAT OFF Video CD/CD TRACK REPEAT DISC REPEAT REPEAT OFF SELECT : SET : SET b. Play mode [Video CD/ CD only] (See p. 39 or 40.) PROGRAM PLAY program play RANDOM PLAY random play ---normal play b • CHAPTER/TITLE REPEAT PLAY (DVD) CURRENT PLAYBACK POSITION END : DISPLAY CURRENT PLAYBACK POSITION track chapter : SET • TRACK/DISC REPEAT PLAY (Video CD/CD) TITLE chapter PLAY DISC REPEAT RANDOM PLAY SET For your reference END : DISPLAY track track chapter TRACK REPEAT CHAPTER REPEAT TITLE REPEAT NORMAL PLAY DISK REPEAT NORMAL PLAY Note • For repeat play in VCR mode, see p. 32. 42 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 42 2002/05/23, 18:13 MP3 Playback Operation *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. MP3 Playback You can use this unit to play MP3 format audio recorded for ■ MP3 playback (During STOP mode) personal use with a computer etc. onto a CD-R or CD-RW. 1) Press to select an MP3 file ( ). Play may not be possible in some cases due to the SET or PLAY to start playback. 2) Press condition of the recording. 1 2 3 Press POWER on the remote or DECK. Press OPEN/CLOSE, and then place a MP3 disc into the disc tray. Press OPEN/CLOSE to close. ■ Select parent folder (During STOP mode) MP3 MENU is displayed and playback is 1) Press to select a folder ( ). started automatically. (The MP3 CD directory is displayed.) 2) Press SET to make changes to the previous directory display. Function Counter Status <Example> Parent Note PLAY MP3 MENU ROOT VA TECHNO POPS JAZZ Folder area (The currently displayed folder turns green) 00 : 00 : 00 .. END_WALTZ DD_CUB I C NOCTURNE NORN PLAY MODE : NORMAL <Example> folder File area (The selected MP3 file/folder is displayed with a cursor.) PLAY MODE ROOT : MP3 file : Folder : Parent folder VA END_WALTZ DD_CUB I C NOCTURNE NORN TECHNO POPS (The MP3 CD directory structure displayed in the above example OSD is shown in the diagram at left.) ■ Forward/Reverse Search Press FF/SLOW+ or REW/SLOW- during play. Press PLAY to release. • Search speed, slow at first, increases with each additional press of the button up to 4 levels. ■ Forward/Reverse Track Skip Press SKIP | or | SKIP during play. Each press skips a track. • If pressed within first 3 seconds of playback, skips to the previous track. If over 3 seconds, returns to first of that track. (| SKIP only.) • Only the SKIP | or | SKIP button can be used for track skip selection during playback. Place unit into Stop mode before performing folder/ file selection (see above right.) • Folder area operation cannot be done. Only file area operation is possible. ■ Select PLAY MODE (During STOP mode) 1) Press to move cursor to PLAY MODE. 2) Press to select the desired PLAY MODE (see below). [PLAY MODE] NORMAL: All MP3 files are selected and played back one time only. SINGLE REPEAT: The selected MP3 file is played back repeatedly. FOLDER REPEAT: The MP3 files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back. DVD Operation JAZZ 4 5 ■ Select folder (During STOP mode) 1) Press to select a folder ( ). 2) Press SET to display files/folders contained in the folder. DISC REPEAT: All MP3 files are played back repeatedly. Press STOP to stop playing. Press OPEN/CLOSE to eject the disc. The MP3 MENU is closed automatically. 43 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 43 2002/05/23, 18:13 DVD Lock Feature *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. You can prevent playback of DVDs of a specific rating level which may be unsuitable for children. • Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited. Ready Checklist DECK is in DVD mode, press DVD. DVD Lock (DVD only) A 4-digit code must be entered to view a blocked program or change rating settings. 1 2 Press ACTION* to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I E LD TV MODE : Letterbox 4:3 PARENTAL LOCK : LEVEL 8 SELECT SET END Press to select “PARENTAL LOCK,” and press SET to display. : : SET : ACTION Caution Discs not encoded with rating level will play even if the jacket states it is for mature audiences. For these discs, the DVD Lock Ratings will not work. <When DVD Lock is activated> YOUR SELECTION EXCEEDS THE , PLAYER S RATING LIMIT. DO YOU WANT TO CHANGE THE LIMIT? YES 3 ENTER 4-D I G I T CODE ---END : ACT I ON ENTER : 0 - 9 1) Press NUMBER keys to enter your secret code. 2) Enter same secret code again for confirmation. 3) Press SET to display. To Make Corrections • Step 2) not necessary when Press repeatedly to move the cursor. Press NUMBER keys to make the correction. 4 changing rating or secret code. • Take care that you are not observed entering the secret code. Press to select rating level, and press SET to select “LOCKED” or “UNLOCKED.” LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs and Video CDs is prohibited. (Use to prohibit play of mature theme DVDs not encoded with rating level.) LEVEL 1 : mature theme DVDs LEVEL 2 : DVDs expressly for children can be played back. LEVEL 3 to 7 : DVDs for general audiences/children can be played back. (DVDs with mature content are prohibited.) LEVEL 8 : NO LIMIT: (Factory preset) All DVDs can be played back. 5 44 Press ACTION twice to end setup. NO SELECT : SET : SET END : DISPLAY After DVD Lock is set and a blocked DVD is played, this message will appear. The message may differ depending on the disc. To continue viewing a blocked program for now, to select “YES” and Press SET. Then, enter your 4 digit secret code. When “NO” is selected, blocked programs cannot be viewed. Change your secret code • You will need your current code. Do step 1 ~ 2 left. Enter current secret code. Press CLEAR to clear the code. Do step 4 to enter new code. Note • DO NOT forget your secret code. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 44 2002/05/23, 18:13 Settings for DVD Operation 1 2 Press ACTION to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 Press to select an item, and press SET. Once initial settings are done, they remain in memory (even after power off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time. Ready Checklist DECK is in DVD mode, press DVD. SELECT SET END : : SET : ACTION DISC LANGUAGES (See below) All languages offered on the disc can be set. If the language not offered is set, the original disc language will be selected. NUMBER keys AUDIO OUTPUT (See p. 46.) CLEAR You can set the audio output that comes from the digital audio output terminal. ACTION STILL MODE (See p. 47.) SELECT To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture. When “AUTO” is set “FIELD” or “FRAME” is selected automatically. SET TV MODE (See p. 47.) To select whether the video material for a widescreen will be played back in the Pan & Scan style, Letterbox style or 16 : 9 style. Disc Languages (DVD only) To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 SELECT SET END : : SET : ACTION Press to select “DISC LANGUAGES,” and press SET to display screen. (Factory preset: English) To select the audio soundtrack language. English/Spanish/French/Japanese Original: Original disc language OTHER ✱✱✱✱: Other language selection*1 “SUBTITLE” selections (Factory preset: AUTO) To select the subtitle language. AUTO: Same language selected for “AUDIO” • If language set for “AUDIO” is used in playback, subtitles will not appear. • If another language is used during playback, the subtitles will appear in the language selected at “AUDIO” setup. English/Spanish/French/Japanese OTHER ✱✱✱✱: Other language selection*1 DVD Operation 3 “AUDIO” selections “MENUS” selections 4 DISC LANGUAGES AUDIO SUBT I TLE MENUS SELECT SET END 5 : English : AUTO : English : : SET : ACTION Press to select an item, and press SET repeatedly for desired language. (Please refer right.) Press ACTION to redisplay DVD menu and go to step 2 to setup another item. Or, press ACTION twice to exit. (factory preset: English) To select the language used in title menus or DVD menus. English/Spanish/French/Japanese OTHER ✱✱✱✱: Other language selection*1 To enter OTHER ✱✱✱✱ code number, Press NUMBER keys (Please refer to language codes on p. 48). To make corrections, press repeatedly to delete language code number, and correct. *1 If the selected language is not offered, the original disc language is selected. 45 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 45 2002/05/23, 18:13 Settings for DVD Operation (continued) Audio Output Ready Checklist Select the digital output to be output from the optical digital audio output connector of DECK. 1 2 Press ACTION* to display MENU. DVD MAIN MENU DISC LANGUAGES AU AUDI DIO O OUTPUT ST I L L MODE : F I LED TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 SELECT SET END 3 : : SET : ACTION AUDIO OUTPUT LPCM(DVD) LPCM(DVD) Dolby Digital dts DRC SURROUND SELECT SET END :: OFF OFF : Bitstream : OFF : OFF : OFF : : SET : ACTION Press to select “AUDIO OUTPUT,” and press SET to display screen. Press to select an item, and press SET repeatedly for output. (See below.) OFF: Linear PCM of less than 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit or 96 kHz, no digital audio is output. (Factory preset) PCM: When playing DVDs recorded in linear PCM of 48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.) ■ “Dolby Digital” selections Bitstream: Dolby Digital bitstream (1ch-5.1ch) is output. (Factory preset) OFF: No output. ■ “dts” selections Bitstream: dts bitstream is output. (Factory preset) OFF: No output. ■ “DRC (Dynamic Range Compression)”selections OFF: Normal audio range is selected. (Factory preset) ON: For dynamic sound even at low volume, this is useful for late-night listening. [Dolby Digital DVDs only]. ■ “SURROUND” selections Surround Sound creates the effect of sound coming from non-existent rear speakers even when only connected to a 2-channel stereo system. OFF: No Surround Sound effect. (Factory preset) ON: Surround Sound effect. 46 Recommended setting LPCM Dolby dts (DVD) Digital No amplifier is connected OFF OFF OFF Type of amplifier to be connected ■ “LPCM (DVD)” selections 4 DECK is in DVD mode, press DVD. Press ACTION to redisplay DVD menu and go to step 2 to setup another item. Or, press ACTION twice to exit. AV amplifier (with digital audio input connector) PCM*1 without Dolby Digital/dts decoder AV amplifier including Dolby Digital decoder OFF* 2 PCM*1 Bitstream OFF*2 OFF AV amplifier including 1 *3 Dolby Digital/dts decoder PCM* Bitstream Bitstream • Make settings according to amplifier connected to optical audio output as shown in above table. • When a dts decoder is not connected, to enjoy dts DVD, please select audio output other than dts at the dts DVD menu screen. Otherwise, there will be no sound. *1 Audio Output 2 from DECK is converted to 48 kHz/16 bit in addition to audio from digital audio output. To enjoy high quality sound at 48 kHz/20 bit /24 bit or 96 kHz, connect the amplifier or decoder directly to the Audio Output 2 connectors, not to the Digital Audio Output connector. [Select “OFF” at the “LPCM (DVD)”.] *2 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers. *3 When a dts decoder is connected, please select “Bitstream” in “dts”. If “OFF” is selected, there will be no sound. Notes • Turn off other surround effects when using this surround effect. • For optimum effect, the distance between DECK and the listener should be about 3 or 4 times the distance between the right and left front speakers. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 46 2002/05/23, 18:13 *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Still Mode Set to reduce jitter in a displayed still picture or a motion picture. 1 2 Press ACTION to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST T I L L MODE : F I ELD TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 SELECT SET END : : SET : ACTION Press to select “STILL MODE,” and press SET repeatedly for mode. (See below.) ACTION AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is automatically selected during the still mode. (Factory preset) FIELD: “FIELD” (Field still) is always selected. This setting will reduce jitter when compared with “AUTO” on some discs. FRAME: “FRAME” (Frame still) is always selected. Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs. 3 SELECT SET Press ACTION to exit this mode. TV Mode Set the screen display style for wide-screen video material playback. Press ACTION to display MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I LED TV MODE : Letterbox 4:3 PARENTAL LOCK :LEVEL 8 SELECT SET END : : SET : ACTION Press to select “TV MODE,” and press SET repeatedly for mode. (See below.) Example • Pan & Scan (Factory preset) DVD Operation 1 2 Pan & Scan 4 : 3 (Factory preset) : Wide-screen video data is played in Pan & Scan style (left and right of screen is trimmed.) • Video data not formatted in Pan & Scan will play in letterbox style. Letterbox 4 : 3 : Wide-screen video data is played in Letterbox style (top and bottom of screen has black margin). 16 : 9 : Set “16: 9” when using Wide-screen TV. 3 • Letterbox Press ACTION to exit this mode. 47 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 47 2002/05/23, 18:13 Language Code List Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 45). Code Language Code Language Code Language Code Language 6565 Afar 7079 Faroese 7678 Lingala 8375 Slovak 6566 Abkhazian 7082 French 7679 Laothian 8376 Slovenian 6570 Afrikaans 7089 Frisian 7684 Lithuanian 8377 Samoan 6577 Ameharic 7165 Irish 7686 Latvian, Lettish 8378 Shona 6582 Arabic 7168 Scots Gaelic 7771 Malagasy 8379 Somali 6583 Assamese 7176 Galician 7773 Maori 8381 Albanian 6588 Aymara 7178 Guarani 7775 Macedonian 8382 Serbian 6590 Azerbaijani 7185 Gujarati 7776 Malayalam 8385 Sundanese 6665 Bashkir 7265 Hausa 7778 Mongolian 8386 Swedish 6669 Byelorussian 7273 Hindi 7779 Moldavian 8387 Swahili 6671 Bulgarian 7282 Croatian 7782 Marathi 8465 Tamil 6672 Bihari 7285 Hungarian 7783 Malay 8469 Telugu 6678 Bengali; Bangla 7289 Armenian 7784 Maltese 8471 Tajik 6679 Tibetan 7365 Interlingua 7789 Burmese 8472 Thai 6682 Breton 7378 Indonesian 7865 Nauru 8473 Tigrinya 6765 Catalan 7383 Icelandic 7869 Nepali 8475 Turkmen 6779 Corsican 7384 Italian 7876 Dutch 8476 Tagalog 6783 Czech 7387 Hebrew 7879 Norwegian 8479 Tonga 6789 Welsh 7465 Japanese 7982 Oriya 8482 Turkish 6865 Danish 7473 Yiddish 8065 Panjabi 8484 Tatar 6869 German 7487 Javanese 8076 Polish 8487 Twi 6890 Bhutani 7565 Georgian 8083 Pashto, Pushto 8575 Ukrainian 6976 Greek 7575 Kazakh 8084 Portuguese 8582 Urdu 6978 English 7576 Greenlandic 8185 Quechua 8590 Uzbek 6979 Esperanto 7577 Cambodian 8277 Rhaeto-Romance 8673 Vietnamese 6983 Spanish 7578 Kannada 8279 Romanian 8679 Volapük 6984 Estonian 7579 Korean 8285 Russian 8779 Wolof 6985 Basque 7583 Kashmiri 8365 Sanskrit 8872 Xhosa 7065 Persian 7585 Kurdish 8368 Sindhi 8979 Yoruba 7073 Finnish 7589 Kirghiz 8372 Serbo-Croatian 9072 Chinese 7074 Fiji 7665 Latin 8373 Singhalese 9085 Zulu 48 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 48 2002/05/23, 18:13 Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions. OSD Caution Page If you attempt to set or review a Timer Recording and the Clock is not set... 24 If DECK is not in Stop mode or a cassette with record tab is not inserted 2 minutes before a Timer Recording is about to begin... 24 25 CHECK CASSETTE RECORD TAB If you press REC on the remote control or DECK, and a cassette is inserted with no record tab... 6 NO CASSETTE If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted... 20 21 TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC If you press STOP or POWER during a Timer Recording... (visible in VCR mode only) 25 VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE OR REFER TO MANUAL If head cleaning becomes necessary while playing back a tape... PLEASE SET CLOCK BY PRESSING ACTION KEY PLEASE PREPARE FOR TIMER REC END 6 : PLAY If you press a function button other than STOP/EJECT or POWER while DECK is in VCR Lock mode... VCR LOCK ACTIVATED 33 REMOTE CONTROL IS SET TO CABLE/DSS MODE USE VCR : VCR KEY USE DVD : DVD KEY If you press an invalid key on the remote while in CABLE/DSS mode... REMOTE CONTROL IS SET TO TV MODE USE VCR : VCR KEY USE DVD : DVD KEY If you press an invalid key on the remote while in TV mode... PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC If you press PLAY, or DECK reads data from a stained or scratched disc in DVD mode. Also, if the type of disc is other than DVD, Video CD or CD... 4 IT IS PROHIBITED TO COPY DVD/VIDEO CD/CD TO VHS If you press REC in DVD mode... 21 28 29 34 28 29 34 For Your Information 49 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 49 2002/05/23, 18:13 Before Requesting Service Check the following points if you are having trouble with your DECK. Power Correction No power… • Completely insert Power Plug into an AC outlet. • Set POWER button to on. • Make sure power source is active. Power turns itself off... • Auto power-off (shutoff) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33) Correction Recording & Playback TV program cannot be recorded... • Check connections between DECK, external antenna, and TV. • Check channel selections. • Make sure your antenna system (CABLE or TV) is correctly set. (Channels [p. 18]) • Make sure cassette record tab is intact. (p. 6) Timer recording cannot be performed… • Confirm that clock is set to current time and date. • Make sure Cable/DSS box (if used) is left on and tuned to channel to be recorded. • Set recording start/stop times correctly. (p. 24) • Timer recording may not be performed or continued if a power interruption occurs before or during a Timer Recording, even after power is restored. There is no playback picture, or the playback picture is noisy or contains streaks... • Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE. • Set VCR/TV selector to “VCR.” • Adjust TRACKING control in either direction. (p. 6) • Try Head Cleaning. (p. 6) During Special effects playback, picture may contain some vertical jitter when using a TV with an Automatic Vertical Hold Control... • Set TV’s Vertical Hold Control to MANUAL, then adjust. DECK cannot be controlled... • • • • • Remote Control Correction Make sure DECK power is on. Check Remote batteries. Make sure VCR LOCK is set to off. (p. 33) Make sure Remote is in proper mode.(p. 28) Make sure Timer Recording is not in progress. DECK cannot be remote controlled... • • • • • • PROG buttons do not respond... • PROG functions are not available in COMPONENT Video Output and S-VIDEO OUT. Set TV to either RF IN or VIDEO IN. (p. 10) • Check Remote batteries. (p. 4) • Press VCR or DVD button for DVD/VCR mode. (p. 28) 50 Make sure DECK power is on. Make sure Remote is in VCR mode. Aim Remote Control directly at remote sensor on DECK. (p.9) Avoid any object blocking signal path. Check Remote batteries. (p. 4) Exposing DECK remote sensor to direct fluorescent or outdoor light may cause signal interference. For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 50 2002/05/23, 18:13 Check the following points if you are having trouble with your DECK. DVD/ Video CD/ CD Correction Play fails to start even when PLAY is pressed... • This DECK cannot play discs other than DVDs, Video CDs and CDs. • The disc may be dirty and require cleaning. Play starts but then stops immediately... • Be sure disc is installed with label side up. Picture is distorted during rapid advance or rapid reverse... • The picture will be somewhat distorted at times: this is normal. No Forward/Reverse Scene Search play... • Some discs may have sections which prohibit Forward/Reverse Scene Search. (p. 23) Play does not start even when title is selected... • Confirm the “DVD LOCK” setting. (p. 44) Audio soundtrack and/or subtitle language is not the one selected at the initial settings... No subtitles... • If the audio soundtrack and/or subtitle language selected at DVD initial settings does not exist on the disc, it will not be accessible. • Subtitles appear only when available on disc. • “OFF” is selected at the changing subtitle language. Select “ON” at the “Subtitle Languages” section (p. 36) to display the subtitles. Alternative audio soundtrack (or subtitle) language cannot be selected... • Alternative language cannot be selected with discs which do not contain more than one language. • For some discs, alternative language cannot be selected with the AUDIO or SUB TITLE button. Try selecting it from the DVD MENU if available. Angle cannot be changed... • This function is dependent on software availability. Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37) Correction Miscellaneous Programs cannot be viewed on TV... Video cassette cannot be inserted... • Make sure TV is set to output of DECK. • Check connections between DECK, external antenna, and TV. • Set VCR/TV selector to “TV.” (p. 21) • Make sure proper signal source is selected. • Insert the cassette with window side up; record tab facing you. The disc cannot be removed.. • First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9) If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262). To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262). or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 51 2002/05/23, 18:13 For Your Information Video cassette ejects when • Make sure cassette record tab is intact. (p. 6) a recording is started or the power is turned off for timer recording... In Stop mode, the motor (CYLINDER) • To enable Quick play mechanism, the cylinder will continues to rotate... rotate for about 3 minutes. This reduces response time from Stop to Play mode. 51 Limited Warranty PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC., AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic/Quasar Video Products Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor. Product Parts Labor One (1) Year (except CCD Image Sensor) CCD Image Sensor - 6 (Six) Months Camcorder Contact Number Service Ninety (90) Days Carry-In or Mail-In 1-800-211-PANA(7262) 1-800-211-PANA(7262) Ninety (90) Days DVD/VCR Deck, One (1) Year A/V Mixer TV/VCR, TV/DVD, One (1) Year (except CRT) TV/DVD/VCR CRT - Two (2) Years Combination Ninety (90) Days Carry-In or Mail-In Ninety (90) Days Carry-In: 21” CRT and Smaller 1-800-211-PANA(7262) In-Home or Carry-In: 22” CRT and Larger One (1) Year (except CRT) CRT - Two (2) Years Ninety (90) Days TV/HDR Combination Rechargeable Batteries Ten (10) Days (in exchange for defective item) Tape (in exchange for Five (5) Days defective item) Memory Cards (in exchange for Ninety (90) Days defective item) Ninety (90) Days In-Home or Carry-In 1-888-843-9788 Ninety (90) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262) Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262) Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262) During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service, as applicable, during the warranty period. If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original purchase date is required for warranty service. Carry-In, Mail-in or In-Home Service For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number listed above or visit Panasonic Web Site: http://www.panasonic.com For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910. In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and does not include removal or re-installation of an installed product. It is possible that certain inhome repairs will not be completed in-home, but will require that the product, or parts of the product, be removed for shop diagnosis and/or repair and then returned. 52 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 52 2002/05/23, 18:13 Limited Warranty Limits And Exclusions This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or other business), rental use of the product, service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or images, data or other memory or recorded content. The items listed are not exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor. PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY. Customer Services Directory For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST. or send e-mail : [email protected] Web Site: http://www.panasonic.com You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site. Service in Puerto Rico Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter: Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Phone (787)750-4300 Fax (787)768-2910 For Your Information Accessory Purchases: 1-800-332-5368 (Customer Orders Only) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST) (Visa, MasterCard, Discover Card, American Express, Check) As of February 2002 53 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 53 2002/05/23, 18:13 Spanish Quick Use Guide/ Guía para rápida consulta Conexiones/Configuracion Inicial Para ajustar el idioma, canal y (READY TO PLAY) Favor realice la conexion de antena o cable antes de conectar el cordon de AC a la toma de pared. Conectando el cordon de AC de la DECK en toma de pared iniciara automaticamente la busqueda de canales y colocacion de tiempo. Conectando Para Ant/Cable-DECK-TV 1 2 DECK Terminal IN FROM ANT. Televisor Conecte Ant/Cable a la entrada de antena de la DECK (DECK In) Conecte la salida de la DECK (DECK Out) a la entrada de antena de la TV (TV In) con el cable-accesorio RF incluido. 1 2 Entrada (IN) desde ANT./CABLE Terminal OUT TO TV VHF/UHF Para Sistema Digital de Satelite (DSS)/ Convertidor de cable-DECK-TV 1 2 Conecte la salida del convertidor de cable a la ”DECK In” con el RF cable accesorio incluido. Conecte “DECK Out” a la “TV In” con el cable-accesorio incluido. Televisor 2 2 Presione el boton DECK del control remoto para dicha modalidad. Encienda la TV y cambie a canal 3. Conecte cordon de AC de la DECK a la toma de pared. La DECK se activara e iniciara busqueda de canales y colocacion de tiempo. Estuche convertidor de TV por cable 1 Terminal OUT TO TV Entrada (IN) desde ANT./CABLE VHF/UHF Realizando configuracion inicial 1 Terminal IN FROM ANT. DECK 3 Selecciones se realizaron automaticamente cuando la configuracion termino, esta pantalla aparece. 9 / 29 / 2002 SUN 2 : 20PM DST : ON SETT I NG : CH 10 AUTO CLOCK SET COMPLETED • Si la pantalla abajo no aparece cheque la conexion DECK-TV y si la TV fue cambiada a el canal 3,trate cambiando a el canal 4. • Para cambios a el canal de salida de la DECK favor hacer referencia a “VCR’s Output Channel” (p. 19). Si “AUTO CLOCK SET IS INCOMPLETE” aparece, coloque manualmente el tiempo, vealo abajo. AUTO CLOCK SET IS I NCOMPLETE PLEASE SET CLOCK BY PRESSING ACT I ON KEY Conectando cordon de AC a la toma de pared. Realizando configuracion inicial CH AUTO SET PROCEEDING CANCEL : STOP AUTO CLOCK SET Al inicio, el idioma de Si la colocacion de tiempo fue incompleta. Presione la tecla ACTION en el control remoto la pantalla está fijado para visualizar la pantalla del menú RELOJ. a inglés. Para cambiar el FIJAR RELOJ idioma consulte la 1 /-- /-----:-página 18. VERANO : ACT 1 -ELEGIR -------MES --------------- PROCEEDING ELEGIR : FIJAR : SET SALIR : ACT I ON 2 CANCEL : STOP Si usa convertidor de cable solo enciendala y seleccione el canal PBS en su horario de uso u horario de zona. Si utiliza receptor DSS este debe estar apagado. PRECAUCION Si se sobre ajusta “NUT TYPE” el cable coaxial RF podria dañar las terminales de conexion. Ajusta ligeramente utiliza solo los dedos. 54 Presione para seleccionar el mes y SET para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (Hora de Verano). FIJAR RELOJ 9 / 29 / 2002 DOM 12:00PM VERANO : ACT ----------------------FIJACION ES COMPLETO 3 Presione dos veces la tecla ACTION para poner el RELOJ en marcha y salir. For assistance, Por ayuda llame please al 1-800-211-PANA(7262) call : 1-800-211-PANA(7262) o envie or send e-mail e-mail a : to [email protected] : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 54 2002/05/23, 18:14 Programación fácil para la grabación con temporizador Operaciones básicas para la reproducción 1 Inserte un cassette, • La alimentación del DECK se activa. En la Pantalla de Visualización Multi Función se ilumina “VCR”. PROG 1 Presione para visualizar PROGRAM. 2 Presione PLAY para reproducir el cassette. 2 • Si el cassette no tiene lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente. 3 Presione STOP para detener el cassette. CA 7 SAB --:-- --:-- -- SLP HOY ELEGIR FECHA DE I N I C I O ELEGIR : FIJAR :SET TERMINAR : PROG Detalles especiales durante la grabación Presione FF/SLOW+ o REW/SLOW- para búsqueda de escenas hacia delante/ hacia atrás. Presione PLAY para liberar. Luego de que la búsqueda se ha iniciado, cada vez que presione FF/SLOW+ o REW/SLOWse cambia la velocidad como sigue: [SLP] aprox. 21X ↔ aprox. 9X [LP] aprox. 9X ↔ aprox. 7X [SP] aprox. 7X ↔ aprox. 3X Si la imágen se interrumpe con la velocidad de 21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x. Presione PAUSE/STILL para imagen Fija (Congelada). Presione PLAY para liberar. Presione PAUSE/STILL en el modo de imagen fija para imágenes cuadro a cuadro. Presione PLAY para liberar. Presione FF/SLOW+ o REW/SLOW- en el modo de imagen fija para imágenes cuadro a cuadro. Presione PLAY para liberar. FECHA I N I C I O PARADA Orden para elegir Ejemplo 1) Para ajustar la FECHA de grabación, presione para seleccionar: 1-31 = una vez, o DIARIO = a la misma hora de lunes a viernes, o SEMANA = a la misma hora cada semana y presione SET para ajustar. 8 Fecha de hoy 9 / 7 31 1 2 6 Orden para elegir SEMANAL (SAB) SEMANAL (LUN) DIARIO SEMANAL (DOM) 2) Para ajustar los ítems que quedan, presione para seleccionar y presione SET para ajustar los tiempos de INICIO/ PARADA, CANAL, o entrada de LÍNEA (pág. 35), y velocidad del cassette (SP, LP, SLP). Presione PROG para finalizar PROGRAM. 3 FE I N I C PARADA CA VEL 7 2 : 00 P 3 : 20 P 02 SLP -- -- : --- : --- --- -- : --- : --- --- : --- --- -- : -CANCELAR: ADD / DLT ELEGIR 1- 8 : ENTRAR : SET SAL I R : PROG Presione REW/SLOW- o FF/SLOW+ en el modo de parada para rebobinado/avance rápido del cassette. Presione EJECT en el control remoto, o STOP/EJECT en el DECK para expulsar el cassette. Presione para seleccionar un número que no está usando para ingresar mas programas y presione SET para ajustar. Luego repita el paso 2. O Presione nuevamente PROG para salir. Operaciones básicas para la grabación el cassette con lengüeta de 1 Inserte protección de grabación (pág. 6). SPEED para seleccionar la 3 Presione velocidad de grabación (pág.6) • SP = Reproducción estándar, • LP = Larga duración, • SLP = Superlarga duración. 4 Presione REC para comenzar a grabar. • Para eliminar escenas indeseadas, presione PAUSE/STILL para pausar, y al presionar nuevamente se reanuda la grabación. • No podrá ver otro canal durante la grabación. Grabación de un toque (grabar en marcha), Presione REC repetidamente para ajustar la hora de grabación (30 min - 4 horas). • La videograbadora termina la grabación a una hora programada. Grabación normal 4:00 3:00 0:30 2:00 1:00 1:30 55 5 Presione STOP para detener la grabación. PV-D4732S P36-60 (2nd) [LSQT0618B].p65 55 Guía para rápida consulta CH / , o las teclas de números 2 Presione para seleccionar el canal. 2002/05/23, 18:14 Spanish Quick Use Guide/ Guía para rápida consulta Operaciones básicas del DVD 1 2 3 Presione POWER en el control remoto o el aparato. Presione DVD para seleccionar el modo DVD. OPEN/ CLOSE POWER 1) Presione OPEN/CLOSE . 2) Ponga un disco en la bandeja de disco. • Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título PLAY hacia arriba, alinéelo con las guías y póngalo en su posición apropiada. REW/ Disco de 3”(8 cm) Disco de 5” (12 cm) SLOW- 4 Presione PLAY para iniciar la reproducción. La bandeja del disco se cierra automáticamente. • Si está usando un DVD interactivo (Interactive DVD) o un Vídeo CD con contol de reproducción (playback control) y aparece un menú de títulos (TITLE MENU) en la pantalla, siga al paso 5. 5 Presione o las teclas numéricas para seleccionar el artículo deseado. Presione SET para la reproducción. Si usa las teclas numéricas, la reproducción comienza automáticamente. 6 7 Presione STOP para parar la reproducción. DVD FF/ SLOW+ STOP PAUSE/ STILL NUMBER keys SKIP SKIP SELECT SET Presione OPEN/CLOSE para expulsar el disco. ■ Para buscar una escena particular Búsqueda hacia adelante Presione FF/SLOW+ en el modo de reproducción. Búsqueda hacia atrás Presione REW/SLOW- en el modo de reproducción. (Para liberar, presione PLAY) ■ Para saltar un capítulo o una pista Salto hacia adelante Presione SKIP l en el modo de reproducción. Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla. Salto hacia atrás Presione l SKIP en el modo de reproducción. ■ Para ver una imagen fija Presione PAUSE/STILL durante la reproducción. (Para liberar, presione PLAY) ■ Para ver imágenes cuadro a cuadro (DVD/Vídeo CD) Presione PAUSE/STILL en el modo de imagen fija. La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal, presione PLAY.) ■ Para ver en cámara lenta (DVD/Vídeo CD) Presione FF/SLOW+ o REW/SLOW- en el modo de imagen fija. (Para liberar, presione PLAY) 56 For assistance, Por ayuda llame please al 1-800-211-PANA(7262) call : 1-800-211-PANA(7262) o envie or send e-mail e-mail a : to [email protected] : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 56 2002/05/23, 18:14 Funcionnamiento del DVD utilizando visualizaciones en pantalla Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.). DISPLAY en el modo reproducción o parada 1 Presione para visualizar Visualizaciones en pantalla. • Cada vez que se presione DISPLAY, la visualización en pantalla cambia como se muestra a continuación. Información seleccionada del disco Información seleccionada de del DECK Pantalla normal CLEAR (o ) para seleccionar el ítem deseado. 2 Presione Presione SET para ajustar. SELECT para seleccionar el ajuste deseado. 3 Presione Presione SET para ajustar. SET Para volver a la pantalla normal, Presione repetidamente CLEAR o DISPLAY. PI STA PBC : 12 : INACTIVO PI STA PBC FIJAR VIDEO CD 0 : 12 : 34 : 17 : INACTIVO : SET SIGUIENTE: DISPLAY FIJAR T I TULO : 12 CAPITULO: 11 DVD 0 : 12 : 34 T I TULO : 12 CA CAPI PITULO TULO : 24 24 VIDEO CD 0 : 12 : 34 DISPLAY DVD 0 : 12 : 34 ELEGIR : FIJAR : SET SIGUIENTE: DISPLAY ELEGIR : FIJAR : SET SIGUIENTE: DISPLAY : SET SIGUIENTE: DISPLAY Guía para rápida consulta 57 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 57 2002/05/23, 18:14 Spanish Quick Use Guide/ Guía para rápida consulta Fijaciones iniciales 1 2 3 Selección de IDIOMAS DEL DISCO [DVD solamente] Presione DVD para seleccionar el mode DVD. Seleccione “AUDIO” Presione ACTION en el modo de parada para visualizar MENU. Presione para seleccionar el artículo deseado. Presione SET. IDIOMAS DEL DISCO Todos los idiomas ofrecidos en el disco pueden ser ajustados, Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco. SALIDA DE AUDIO Puede usted ajustar la salida audio procedente del terminal de salida audio digital. DETENER RASTREO Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija. PREFERENCIA Para seleccionar si el material del vídeo para pantalla ancha será vuelto a reproducir en el estilo Pan&Scan, en el estilo Letterbox o en el estilo 16 : 9 en la pantalla. 4 5 Presione para seleccionar el artículo deseado. Presione SET. Volver a visualizar el menú de DVD para continuar el ajuste. (Fijación de fábrica : inglés) Inglés / Español / Francés / Japonesa : Originl : Se seleccionará el idioma original de cada disco. OTRO **** : Se puede seleccionar el otro idioma. Seleccione “SUBTITULO” (Fijación de fábrica) AUTO : Se seleccionará el mismo que fue seleccionado en la preparación de “AUDIO”. • Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán. • Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO” Inglés / Español / Francés / Japonesa : OTRO **** : Se puede seleccionar el otro idioma. Seleccione “MENU” (Fijación de fábrica : inglés) Inglés / Español / Francés / Japonesa : OTRO **** : Se puede seleccionar el otro idioma. Presione ACTION y pase al paso 3 para ajustar otro ajuste o, para salir, presione ACTION tres veces. Cambio del idioma de subtítulos [DVD solamente] EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible. 1 Presione SUBTITLE 2 Presione para seleccionar el idioma deseado. Presione (o ) para ajustar. Presione para seleccionar “ACTIVO” o “INACTIVO.” 58 durante la reproducción. Cuando no haya subtítulos grabados, “-” se visualizará en lugar del número de idioma. Cambio del idioma de la pista de sonido [DVD solamente] EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible. 1 Presione AUDIO durante la reproducción para visualizar la pantalla AUDIO. 2 Presione para seleccionar idioma. For assistance, Por ayuda llame please al 1-800-211-PANA(7262) call : 1-800-211-PANA(7262) o envie or send e-mail e-mail a : to [email protected] : [email protected] PV-D4732S P36-60 (2nd) [LSQT0618B].p65 58 2002/05/23, 18:14 Selección de vocal para los discos de Karaoke [DVD/Video CD] Visión desde otro ángulo [DVD solamente] 1 2 Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde un número de ángulos diferentes. Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón ANGLE. 1 Presione ANGLE durante la reproducción para visualizar la pantalla de ángulo. ANGULO : 1 ELEGIR : 2 FIJAR : SET Presione para seleccionar el ángulo deseado. ANGULO ANGULO : 2 ELEGIR : FIJAR : SET Utilización de un menú de títulos [DVD solamente] Algunos discos con películas, por ejemplo, vienen con dos o más títulos. Si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película. 1 2 Presione TITLE durante la reproducción. Ahora se visualiza una lista de los títulos del disco. T I TLE MENU Dogs Cas t l es Love r s B i r ds Dogs of the world Presione AUDIO durante la reproducción para visualizar la pantalla AUDIO. Presione (o ) para seleccionar el ajuste deseado. Presione (o ) para ajustar. (DVD solamente) • DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF • DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF • Video CD L R Utilización de un menú de DVD [DVD solamente] Algunos discos DVD tienen estructuras únicas de menús llamadas menús DVD. Por ejemplo, los DVDs programados con un contenido complejo proporcionan menús guía, y los grabados con varios idiomas proporcionan menús para audio e idiomas de subtítulos. Aunque los contenidos de los menús DVD y la operación cambian de disco a disco, a continuación se explica la operación básica cuando se utiliza esta característica. 1 Presione MENU durante la reproducción. El menú de DVD introducido en el disco se visualiza ahora. 2 Presione o las teclas de números para seleccionar el título deseado. Presione SET. LR DVD MENU 1 . SUBT I TLE 2 . AUD I O 3 . ANGLE Presione o las teclas de números para seleccionar el ítem deseado. Presione SET. Ampliación de la imagen [DVD solamente] Presione ZOOM repetidamente para cambiar el tamaño de la imagen como se indica a continuación: ■ Use los botones , , y para desplazar la posición hacia arriba, hacia abajo, hacia la izquierda o hacia la derecha. 2da Guía para rápida consulta Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM. 3da 59 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 59 2002/05/23, 18:14 Index DECK & VCR A ACTION button .............................................. 8, 18 Accessories ......................................................... 4 ADD/DELETE button (Add or Delete a Channel) . 8, 19 Audio Broadcast types (Stereo/SAP/Mono) .... 26 Audio Mode (Playback, Recording) ................. 27 Auto Operation Functions ............................... 31 Auto Shut-Off .................................................... 33 B Batteries .............................................................. 4 C Channel (“SET UP CHANNEL”) ....................... 18 Channel Up/Down, Tracking/V-Lock Button ... 6, 8 Clock (“SET CLOCK”) ....................................... 18 Commercial Skip ............................................... 31 Connections ............................................. 12 ~ 15 Copy Your Tapes (Dubbing) ............................ 35 COUNTER RESET button ............................ 8, 32 Customer Services Directory ............................ 53 D DISPLAY button ........................................... 8, 11 DSS/CABLE mode button ........................... 8, 28 DST (Daylight Saving Time) ............................. 19 E EJECT button ............................................... 8, 20 ENTER button (For tuning TV Channel) ..... 8, 28 F FAST FORWARD/SEARCH button ............. 8, 20 H Head Cleaning .................................................... 6 I Index Search .................................................... 30 Indicator (Multi Function Display) .................... 11 Initial Setup (Ready to Play) ..................... 16, 17 INPUT button ................................................ 8, 35 L Limited Warranty ....................................... 52, 53 Location of Controls (Remote, DECK) ..... 8 ~ 10 M Multi-Brand Control .................................... 28, 29 O On-Screen Displays (VCR) ................................ 11 One Touch Recording ...................................... 21 P PAUSE/STILL button (Still Picture) ............. 8, 20 PLAY button (Playback a Tape) ................. 8, 20 POWER button ................................................... 8 PROG button (PROGRAM) .......................... 8, 24 Program Clear, Review, Replace ..................... 25 Program End Search ........................................ 30 Q Quality Picture ..................................................... 6 R REC button (Record on a Tape) ................. 8, 21 Record Tab ......................................................... 6 Remote Sensor ................................................... 9 Remote Warning ............................................... 34 Repeat Play ...................................................... 32 REWIND/SEARCH button ............................ 8, 20 S SAP/Hi-Fi ........................................................... 27 SEARCH (Index and Program End Search) ... 30 Servicenter List ................................................. 52 SLOW+/SLOW- button ( Slow Motion Picture) .. 8, 20 Spanish Quick Use Guide ....................... 54 ~ 59 Specifications ...................................................... 7 SPEED button .............................................. 8, 21 Still (Freeze) Picture ......................................... 20 STOP button ................................................. 8, 20 T Tape Position, Tape Status ............................. 34 Timer Recording ............................................... 24 Trouble Shooting ....................................... 50, 51 TV mode button ............................................ 8, 28 V VCR Lock .......................................................... 33 VCR mode button ......................................... 8, 28 VCR/TV button ......................................... 8, 9, 21 VOLUME +/- button (TV Volume) ............... 8, 28 W Warning and Instruction Displays .................... 49 Weak Signal Display ......................................... 33 Z ZERO SEARCH button ................................ 8, 32 DVD A ACTION button ............................................. 8, 45 ANGLE button (Multiple Angle Viewing) ..... 8, 37 AUDIO CONTROL button ............................ 8, 40 AUDIO button (Audio Soundtrack Language) .. 8, 36 Audio Output (For Selecting Audio Output) ... 46 Auto Power Off Function .................................. 23 C CLEAR button ........................................ 8, 39, 44 Component Video Output ......................... 10, 13 D Disc Languages ................................................ 45 DISPLAY button (“On-Screen Display”) ...... 8, 41 DVD Menu ......................................................... 38 DVD mode button ......................................... 8, 28 DVD Lock Ratings ............................................ 44 F Frame by Frame Picture ................................... 23 Forwards/Reverse Chapter/Track .................... 23 Forwards/Reverse Scene Search .................... 23 K Karaoke (Vocal Selection for Karaoke Discs) .... 37 L Language Code List ........................................ 48 M MENU button (To display DVD Menu) ........ 8, 38 MP3 ................................................................... 43 Multiple Angle Viewing ..................................... 37 O OPEN/CLOSE button ................................... 8, 22 Optical Digital Audio Output ..................... 10, 15 P PLAY button (Play a Disc) ........................... 8, 22 Program Play (For Video CD/ CD) ................... 39 R Random Play (For Video CD/ CD) ................... 40 Repeat Play ...................................................... 42 Resume Function ............................................. 23 RETURN button ............................................ 8, 22 S SEARCH button (Forward/Reverse Scene Search) ............. 8, 23 SKIP l or l button (Forward/Reverse Chapter/Track) ............. 8, 23 SLOW+/SLOW- button (Slow Motion Picture) . 8, 23 Sound Output Level ......................................... 40 STILL button (Still Picture or Pause) .......... 8, 23 Still Mode (For selecting “FIELD” or “FRAME”) ... 47 STOP button ................................................. 8, 22 SUBTITLE button (For selecting Subtitle Language) ............. 8, 36 SURROUND button ...................................... 8, 23 S-Video Out ............................................... 10, 13 T TITLE button (Title Menu) ............................ 8, 38 TV Mode (For selecting the screen display style) .... 47 V Video CD ........................................................... 23 Z ZOOM button (Picture Zoom) ...................... 8, 37 Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc. Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 PV-D4732S P36-60 (2nd) [LSQT0618B].p65 60 P Printed in Indonesia LSQT0618B S0302-1052 2002/05/23, 18:14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement