RESET

MICRO SD DO DC12V

ETHERNET

DO DC12V

ETHERNET

RESET

MICRO SD

Quick Start Guide

Before operating the unit, please read this manual thoroughly and keep this for future reference.

Please access our website and download necessary IPAdminTool first: http://www.rivatech.de/en/downloads/software

SV3502(73NIR)04-2017-A

About the manual

This manual provides the brief instructions for the installation and the basic configuration of your IP device. For more information about the installation and configuration, refer to the

Part names and functions

referring to the following images.

Reset

Ethernet button connector

MICRO

SD

MICRO

SD

4) Open the dome cover with the provided L wrench (3mm), install the provided ferrite core to the LAN cable by referring to the squared image on the bottom left of this page, and connect all the necessary cables dropped from the ceiling to the corresponding connectors on the camera.

5) Prepare the screws (M4x30) with the O-rings inserted. Then, place the camera body to match the alignment holes with the corresponding plastic anchors, insert the O-ring inserted screws into the screw holes on the camera body, and tighten them into the plastic anchors with a screw driver.

6) Adjust the angle of the camera. Refer to the section,

Adjusting angle of camera for more information.

7) Adjust zoom and focus of the camera. Refer to Adjusting zoom and focus for more information.

8) Reattach the dome cover to the camera body by aligning the alignment marks on both the dome cover and the camera body.

DO

C

9)

1 C 1

Once the dome cover and the camera body are properly

+ aligned, tighten the bolts on the dome cover into the camera

ETHERNET body with the provided L wrench for the firm attachment. Then,

RESET

C

DO

1 remove the protection film from the dome cover.

C

DI

1

DC12V

+

CAUTION

ETHERNET

To prevent from damage, place the camera on a stable and nonvibrating surface.

SD

DO

C 1 C

DI

1

DC12V

+

Adjusting angle of camera

gimbal bracket

A. To pan, rotate the gimbal bracket clockwise or counter-clockwise.

(The panning range is limited to 358 degrees.)

Terminal connector

Reserved DO DI AUDIO DC 12V micro

SD/SDHC card slot

X X C 1 C 1 O I - +

Terminal Connector: Connect the provided terminal block for cable connection of digital input/output, audio input/output, and DC12V power.

Ethernet Connector: Connect an RJ-45 LAN cable for 10/100 Base-T

Ethernet (PoE supported).

Reset Button: Press the button either for the restart or the factory default of the device. For restart ,

1.

press the button only for 2 seconds while the device is powered on.

2.

Wait for the system to reboot. For factory default , the device is powered on.

2.

1.

press the button for 10 second while

Wait for the system to reboot. mircoSD/SDHC Card Slot: Insert a card up to 32GB.

Class 4 or the above is recommended for HD recording.

gimbal tilt stopper

B. To tilt, tilt the gimbal by referring to the image on the left.

Installation

There is only one type of mounting explained in this manual. Refer to the device’s installation guide for more various mounting types. inner liner

C. For the horizontal rotation of the lens, rotate the inner liner clockwise or counter-clockwise.

(The rotating range is limited to 358 degrees.)

2 turns

ETHERNET

WIRE

NOTE

Tighten the tilt stopper after the tilt angle is confirmed.

CAUTION

Refrain from continuous rotation of the camera gimbal to a single direction as it is linked with an internal cable.

M4x30 screw

ETHERNET

1) Place the installation template included in the package on a desired installation surface.

DO

C 1 C

DI

1

DC12V

+

2) Drill three holes for the plastic anchors based on the template paper, and insert the plastic anchors into the holes. (In case you need to connect the cables through the mounting surface, drill an additional hole to pass the cables based on the size of the cable entry hole.)

3) Attach the provided silicon waterproof band to the bottom of the camera body for the prevention of water permeation.

ETHERNET

DO

C 1 C

DI

1

DC12V

+

The zoom and focus can be managed via the camera’s web page

MICRO

RESET

SD (path: Setup > Video & Audio > Zoom/Focus). Thus, it is necessary to connect the device on a network in advance to the zoom and focus adjustment.

SD

- Adjust zoom/focus by clicking the arrow buttons: The buttons move the lens more extensively than the buttons .

- If you want to set the focus automatically, click One Click Focus . by clicking Calibrate .

DO

C 1 C

DI

1

DC12V

+

ETHERNET

MICRO

SD

ETHERNET

WIRE

ETHERNET

WIRE

ETHERNET

WIRE

Setting up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device by converting the MAC address’s hexadecimal numbers. The MAC address is at the bottom of the device. Be sure that the device and the PC are on the same network area before the installation.

Generic IP Environment

1) Convert the device’s MAC address to the IP address. Refer to the

Hexadecimal-Decimal Conversion Table at the end of this manual.

SETUP page

To setup the device configuraiton:

1) Click the Setup button on the upper left corner of the web page.

2) Enter the user name and the password when the login page is displayed. Then, click OK .

(The default user name and the password are root and pass .)

To learn how to set up the camera on the web page for the advanced configurations, refer to the webpage user’s manual.

Reboot

*

You can reboot the device via the camera’s webpage, too.

1) Go to Setup > Maintenance > Reboot on the camera’s webpage.

2) Click Reboot to reboot the device

*How to reboot on the device is found in the Part names and functions section on the previous page.

IPAdminTool

IPAdminTool is a management tool to automatically scan all the network products for the devices’ administrative tasks, which include network configurations, firmware update, device reboot, factory default, and device configuration.

To modify the device’s default IP address for a customized network area;

1) Find the device from IPAdminTool’s list, and highlight the device’s name.

2) Right-click the mouse, select IP Address , and select Single ; The IP setup window will appear.

Factory Default

*

You can initialize the current settings to the factory default values via the camera’s webpage, too.

1) Go to Setup > Maintenance > Reset All Settings on the camera’s webpage.

2) Select the items that you want to preserve from the initialization among network settings, user account information, and time zone setting.

3) Click Reset All Settings .

*How to do factory default on the device is found in the Part names and functions section on the previous page.

Safe mode

Your device will get restarted in safe mode if the device does not completely boot certain times. The main causes for safe mode are as follows.

* The power supply is continually unplugged certain times in the middle of system booting.

* The firmware files required for system booting are damaged.

* There are conflicts in the system settings.

You will see the page to indicate that your device is in safe mode and to guide you what to do by steps. Follow the instructions on the webpage according to each step.

NOTE

If your device is still in safe mode after trying to update firmware, please contact your local agency to get further assistance .

Give a new unique IP address by modifying the last two digits.

3) On the New Information table in the Single IP Change window, modify the last two digits of the device’s IP address, and modify the rest parts including subnet mask, gateway, and DNS if necessary by checking the user/ PC network area information.

4) Make sure to input the correct ID and PW of the device (default: root / pass).

5) Click Apply to complete the modification.

Viewing video on web page

Once the device’s IP address has been identified, type the URL in a web browser to access the camera. At the first time access, the installation window may pop up.

1) When the browser asks to install the AxUMF software, click the

Install button to proceed.

2) When the Setup installation pop-up window appears, click the

Install button to preceed with the rest of the installation.

NOTE

The figures during the installation process may differ depending on the system OS and the IE version.

Hexadecimal-Decimal conversion table

Refer to the following table when converting the MAC address of your device to IP address.

41

42

43

44

3D

3E

3F

40

45

46

47

48

49

35

36

37

38

39

3A

57

58

3B 59

3C 60

53

54

55

56

69

70

71

72

73

65

66

67

68

61

62

63

64

Hex Dec

25 37

26

27

38

39

28

29

2A

40

41

42

31

32

33

34

2B 43

2C 44

2D

2E

2F

30

45

46

47

48

49

50

51

52

10 16

11 17

12 18

13 19

14 20

15 21

16 22

17 23

18 24

19 25

1A 26

1B 27

1C 28

1D 29

1E 30

1F 31

20 32

21 33

22 34

23 35

24 36

Hex Dec

0 0

1

2

1

2

3

4

5

3

4

5

6

7

8

9

6

7

8

9

0A 10

0B 11

0C 12

0D 13

0E 14

0F 15

7F 127

80 128

81 129

82 130

83 131

84 132

85 133

86 134

87 135

88 136

89 137

8A 138

8B 139

8C 140

8D 141

8E 142

8F 143

90 144

91 145

92 146

93 147

Hex Dec

6F 111

70 112

71 113

72 114

73 115

74 116

75 117

76 118

77 119

78 120

79 121

7A 122

7B 123

7C 124

7D 125

7E 126

5E

5F

60

61

5A 90

5B 91

5C 92

5D 93

94

95

96

97

62

63

98

99

64 100

65 101

66 102

67 103

68 104

69 105

6A 106

6B 107

6C 108

6D 109

6E 110

56

57

58

59

50

51

52

53

54

55

Hex Dec

4A 74

4B 75

4C 76

4D 77

4E 78

4F 79

86

87

88

89

80

81

82

83

84

85

A4 164

A5 165

A6 166

A7 167

A8 168

A9 169

AA 170

AB 171

AC 172

AD 173

AE 174

AF 175

B0 176

B1 177

B2 178

B3 179

B4 180

B5 181

B6 182

B7 183

B8 184

Hex Dec

94 148

95 149

96 150

97 151

98 152

99 153

9A 154

9B 155

9C 156

9D 157

9E 158

9F 159

A0 160

A1 161

A2 162

A3 163

C9 201

CA 202

CB 203

CC 204

CD 205

CE 206

CF 207

D0 208

D1 209

D2 210

D3 211

D4 212

D5 213

D6 214

D7 215

D8 216

D9 217

DA 218

DB 219

DC 220

DD 221

Hex Dec

B9 185

BA 186

BB 187

BC 188

BD 189

BE 190

BF 191

C0 192

C1 193

C2 194

C3 195

C4 196

C5 197

C6 198

C7 199

C8 200

Hex Dec

DE 222

DF 223

E0 224

E1 225

E2 226

E3 227

E4 228

E5 229

E6 230

E7 231

E8 232

E9 233

EA 234

EB 235

EC 236

ED 237

EE 238

EF 239

F0 240

F1 241

F2 242

F3 243

F4 244

F5 245

F6 246

F7 247

F8 248

F9 249

FA 250

FB 251

FC 252

FD 253

FE 254

FF 255