ALFI BRAND Single-Handle Wall Mount Bathroom Faucet Installation instructions

- INSTALLATION INSTRUCTION Ds
A SINGLE-LEVER CONCEALED WASHBASIN MIXER SS
a ITEM No.: AB1256 FILE NO. 5403
% ACCESSORIES CHECKING
LIST OF THE STANDARD ACCESSORIES:
Please double-check the accessory list hereinafter and contact ourcompany or our distributor for any unconformity.
Remarks:
1, Without affecting their performancing, accessories may be changed without further notice.
2, Drawings for reference only. Product size & shape refer to actual faucet.
12
The component list|QTY |The component listiQTY [The component list{QTY |The component list | QTY
1.Main body 1 | 5.Handle 1 | 9. Cover plate 2 1 | 13.Allen key 1
2.Expansion plug 4 | 6.Screw 1 1 | 10. Screw? 1 | 14 Instruction manual | 1
3.Self-tapping screw | 4 7 Indicator 1 11. Spout set 1 |
4.Cover plate 1 1 | 8.Plastic guard 1 1 | 12. Plastic guard 2 | 1
X Installation Instructions
x Do not disassemble the main body, as it has been installed 4 commissioned —( d> a
correctly 8 precisely before leaving the factory.
Y To avoid the faucet from jamming, do flush the water pipe before installation.
<=
= =
= 5
D
o
Q wn
—
w After installation, make sure every joint safely sealed 8 no leaking. о В 7
x The nominal water pressure is 0.05 -1.0Mpa (including cold & hot water Disessemble | | /. 7 д Y
pressure), suitable for water temperature from 4'C to 90 C.
vc Make sure to connect the hot/cold inlet pipe correctly, if standing in front, hot
water pipe connecting to the left & cold water pipe connecting to the right.
1-
X Dimension Drawing
_ 180 _
_ 120 _
|
| À
— —
lr
158
X Installation Procedures
1 2.
==
=] o 4-06
Va
Cold water
75 2
ATW
ANNO
120
Dig wall view
2.Fixing the main body(1) on the wall by the self-tapping
screw(3), connecting the water supplying pipes and test
the tightness of water supplying according to the following
water pressure conditions:
1) While closing of cartridge:
<1.6MPa to test the supplying pipes and faucet;
2)While opening of cartridge, do not block the water oulet:
<0.4MPa to test the supplying pipes and faucet;
Make sure the tightness of the faucet and pipes, put the
plastic guard 1(8)and plastic guard 2(12).
1.Measure the positions of the 406 holes in the wall space
of pre-digged, knock the expansion plug(2) into the holes.
9.
——
cr
Less than10mm
«E —
bo
y
“>
CT
= =
13) [— —
N N
AO
11 ee. Pa
UE
3. Fill the empty parts around the main body with cement,
paste the bricks after covering the groove, the thickness
of the brick parts should be no more than 10mm. Remove
the plastic guard after cement air dried.
4. Then twist PTFE tape on the thread of the spout set(11),
put the spout set to the main body(1), and install the cover
plate2(9) to the wall and fix it with screw2(10).
|
7
\
<<£2—Ñ 2
<>
<>
—
—
—
/
[LL
5.Put the cover plate1(4) to the main body(1),
fix the handle(5) by the screw1(6) on the control valve,
and put the indicator (7) on.
6.Finally, connect the inlet hose and outlet hose, open
the water supply and test the tightness to confirm finishing
installation.
-3-
x Usage
Y How to operate the mixer handle:
1) Raise the handle lever up for opening water, push down to close.
2) Turn the handle lever to the left to increase hot water flow, to the right to
lower water temperature.
( в
% Cleaning á Maintenance
> To keep the product clean 8 shining, follow the steps as below:
1. Flush with clean water & dry with soft cloth only;
2. If any dirt, clean with soft liquid or transparent glass detergent.
3. Do not use any scrubbing detergent, polisher, sand-cloth,
paper tissue or scraper.
4. Do not use acid detergent, indissovable grain-like detergent or soap.
5. Circumrotate the aerator off and clean it when necessary.
X This installation instruction is only for your reference,
the final right to explain & to revise it belongs to us. Serial number: 80010101497