Zebra TC72 User Guide
Reklam
Reklam
TC72
Touch Computer
MN-003676-01
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google LLC. All other trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/copyright .
WARRANTY: For complete warranty information, go to www.zebra.com/warranty .
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula .
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if
Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Revision History
Changes to the original guide are listed below:
Change Date
-01 Rev A 7/2019 Initial release.
Description
2
Table of Contents
3
Table of Contents
Transferring Files with a Host Computer via USB ................................................. 37
Entering Numbers, Symbols, and Special Characters .................................... 45
4
Table of Contents
5
Table of Contents
Responding with a Private Response ............................................................. 69
Removing a Sub Chat Head Icon ................................................................... 72
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner .................... 82
Pairing the RS507/RS507X/RS6000 Hands-Free Imager ............................................ 83
Pairing in HID Mode Using Near Field Communication ........................................ 83
Pairing Using Bluetooth Human Interface Device ................................................. 85
6
Table of Contents
Pairing Using Bluetooth Human Interface Device ................................................. 86
Configuring the Device to Use a Static IP Address ............................................... 96
7
Table of Contents
Configuring Ethernet Static IP Address ........................................................ 118
Configuring Ethernet Static IP Address ........................................................ 142
Connecting a Headset to the 3.5 mm Audio Adapter .......................................... 144
8
Table of Contents
Removing the Device from the Trigger Handle ................................................... 157
9
Table of Contents
Installing Applications Using the USB Connection .............................................. 177
Installing Applications Using the Android Debug Bridge ..................................... 178
Downloading the System Update Package ......................................................... 180
Downloading the Enterprise Reset Package ....................................................... 182
Formatting a microSD Card or USB Drive as Portable Storage ................... 186
Formatting a microSD Card as Internal Memory .......................................... 186
10
Table of Contents
11
About This Guide
Configurations
This guide covers the following configurations:
Configuratio n
TC720L
Radios
WLAN: 802.11 a/b/g/n/ac/d/h/i/r/k/v
3 w
/
WPAN: Bluetooth v5.0 Low Energy
Display Memory
4.7” High
Definition
(1280 x 720)
LCD
4 GB
RAM/32 GB
Flash
Data
Capture
Options
2D imager, camera and integrated
NFC
Operating
System
Android 9
Notational Conventions
The following conventions are used in this document:
•
Bold
text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
12
About This Guide
Service Information
If you have a problem with your equipment, contact Customer Support for your region. Contact information is available at: zebra.com/support .
When contacting support, please have the following information available:
• Serial number of the unit (found on manufacturing label)
• Model number or product name (found on manufacturing label)
• Software type and version number.
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, the user may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
Remove the microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.
Software Versions
To determine the current software versions:
1. Swipe down from the Status bar with two fingers to open the Quick Access panel and then touch .
2. Touch
About phone
.
3. Scroll to view the following information:
• Model
• Android version
• Kernel version
• Build number.
To determine the device serial number, touch
About phone
>
Model & hardware
.
• Serial number
13
Getting Started
Introduction
This chapter provides information to get the device up and running for the first time.
Unpacking
1. Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
2. Verify that the following are included:
• Touch computer
• 4,620 mAh PowerPrecision+ Lithium-ion battery
• Hand strap
• Regulatory Guide.
3. Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global
Customer Support center immediately.
4. Prior to using the device for the first time, remove the protective shipping film that covers the scan window, display, and camera window.
14
Getting Started
Features
Figure 1
Front View
17
16
15
14
13
18
12
11
1
2
3
10
9
4
8
5
7
6
9
10
11
12
13
Table 1
Front View Features
4
5
2
3
1
Number
6
7
8
Item
Touch Screen
Scan Button
PTT Button
Back Button
Home Button
Function
Displays all information needed to operate the device.
Initiates data capture (programmable).
Initiates push-to-talk communications (programmable).
Displays the previous screen.
Displays the Home screen with a single press.
On device with GMS, opens the Google Now screen when held for a short period of time.
Use for communications in Handset mode.
Microphone
Charging
Contacts
Speaker
Search Button
Menu Button
Light Sensor
Provides power to the device from cables and cradles.
Provides audio output for video and music playback. Provides audio in speakerphone mode.
Opens the Recent App screen.
Opens a menu with items that affect the current screen or app.
Determines ambient light for controlling display backlight intensity.
Proximity Sensor Determines proximity for turning off display when in handset mode.
Power Button Turns the display on and off. Press and hold to reset the device, power off or swap battery.
15
Getting Started
Table 1
Front View Features (Continued)
Number
14
15
16
17
18
Item
Microphone
Receiver
Charging/Notifica tion LED
Data Capture
LED
Front Facing
Camera
Use for communications in Speakerphone mode.
Use for audio playback in Handset mode.
Indicates battery charging status while charging and app generated notifications.
Indicates data capture status.
Function
Use to take photos and videos (optional).
Figure 2
Rear View
27
26
24
28
30
29
25
19
24
23
20
21
20
21
22
23
Table 2
Back View Features
Number
19
24
25
26
27
Item
Interface
Connector
Exit Window
Microphone
Scan Button
Volume
Up/Down Button
Battery Release
Latches
Elastic Sleeve
Battery
Hand strap
Function
Provides USB host and client communications, audio and device charging via cables and accessories.
Provides data capture using the imager.
Use during video recording and for noise cancellation.
Initiates data capture (programmable).
Increase and decrease audio volume (programmable).
Press to remove the battery.
Use to hold optional stylus.
Provides power to the device.
Use to securely hold the device in your hand.
16
Getting Started
Table 2
Back View Features (Continued)
Number
28
29
30
Item
Hand strap
Mounting Point
Camera
Camera Flash
Provides latching point for the hand strap.
Takes photos and videos.
Function
Provides illumination for the camera.
Setting Up the Device
To start using the device for the first time:
1. Install a SAM card (optional).
2. Install a micro secure digital (SD) card (optional).
3. Install hand strap (optional).
4. Install the battery.
5. Charge the device.
6. Power on the device.
Installing the SAM Card
CAUTION
:
grounded.
Follow proper electrostatic discharge (ESD) precautions to avoid damaging the Secure Access Module (SAM) card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly
NOTE
:
If using a micro SAM card, a third-party adapter is required.
1. Lift the access door.
Figure 3
Remove Access Door
17
Getting Started
2. Insert a SAM card into the SAM slot with the cut edge toward the middle of the device and the contacts facing down.
Figure 4
SAM Card Installation
Mini SAM Slot
3. Ensure that the SAM card is seated properly.
4. Replace the access door.
Figure 5
Replace Access Door
5. Press the access door down and ensure that it is properly seated.
CAUTION
:
Access door must be replaced and securely seated to ensure proper device sealing.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION
:
Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD pre cautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
-
1. Lift the access door.
Figure 6
Remove Access Door
18
Getting Started
2. Slide the microSD card holder to the Open position.
Figure 7
Open microSD Card Holder
3. Lift the microSD card holder.
Figure 8
Lift microSD Card Holder
4. Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
Figure 9
Insert microSD Card into Holder
19
Getting Started
5. Close the microSD card holder door and slide the door to the Lock position.
Figure 10
Close and Lock microSD Card in Holder
6. Replace the access door.
Figure 11
Replace Access Door
7. Press the access door down and ensure that it is properly seated.
CAUTION
:
Access door must be replaced and securely seated to ensure proper device sealing.
Installing the Hand Strap and Battery
NOTE
:
User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Pro
tection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
NOTE
:
Installation of the hand strap is optional. Skip to step 3 if not installing the hand strap.
1. Remove the hand strap filler from the hand strap slot. Store the hand strap filler in a safe place for future replacement.
Figure 12
Remove Filler
20
Getting Started
2. Insert the hand strap plate into the hand strap slot.
Figure 13
Insert Hand Strap
3. Insert the battery, bottom first, into the battery compartment in the back of the device.
Figure 14
Insert Bottom of Battery into Battery Compartment
4. Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 15
Press Down on Battery
21
Getting Started
5. Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
Figure 16
Secure Hand Strap Clip
Charging the Battery
Before using the device for the first time, charge the main battery until the green Charging/Notification light emitting diode (LED) remains lit. To charge the device, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the device, see Accessories for more information.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or accessory always performs battery charging in a safe and intelligent manner. At higher temperatures (approximately +37°C (+98°F)) the device or accessory may, for small periods of time, alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device or accessory indicates when charging is disabled due to abnormal temperatures via its LED.
To charge the main battery:
1. Connect the charging accessory to the appropriate power source.
2. Insert the device into a cradle or attach to a cable. The device turns on and begins charging. The
Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
Charging Indicators
Table 3
Charging/Notification LED Charging Indicators
Off
State Indication
The device is not charging. The device is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered.
Slow Blinking Amber (1 blink every 4 seconds)
Solid Green
The device is charging.
Charging complete.
Fast Blinking Amber (2 blinks/second) Charging error:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
22
Getting Started
Table 3
Charging/Notification LED Charging Indicators (Continued)
seconds)
State
Slow Blinking Red (1 blink every 4
Solid Red
Fast Blinking Red (2 blinks/second)
Indication
The device is charging but the battery is at end of useful life.
Charging complete but the battery is at end of useful life.
Charging error but the battery is at end of useful life.
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
Zebra Visibility Services
The device captures and provides device analytics to a system administrator. The first time the device boots
(or after a Factory reset), the
Zebra Services
agreement screen displays.
Figure 17 Zebra Services
1. Touch the
Device Data
switch to disable the device from sending analytics data.
2. Touch
OK
.
Replacing the Battery
NOTE
:
User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Pro
tection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
CAUTION
:
Do not add or remove SAM or microSD card during battery replacement.
3. Remove any accessory attached to the device.
4. Press the Power button until the menu appears.
23
Getting Started
5. Touch
Battery Swap
.
6. Follow the on-screen instructions.
7. Wait for the LED to turn off.
8. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 18
Remove Hand Strap Clip
9. Press the two battery latches in.
Figure 19
Press Battery Latches
24
10.Lift the battery from the device.
Figure 20
Lift the Battery
Getting Started
CAUTION
:
Replace the battery within two minutes. After two minutes the device reboots and data may be lost.
11.Insert the replacement battery, bottom first, into the battery compartment in the back of the device.
12.Press the battery down until the battery release latch snaps into place.
13.Replace the hand strap, if required.
14.Press and hold the Power button to turn on the device.
NOTE
:
After replacing the battery, wait 15 minutes before using
Battery Swap
again.
Replacing the SAM Card
To replace the SAM card:
1. Press and hold the Power button until the menu appears.
2. Touch
Power off
.
3. Touch
OK
.
25
Getting Started
4. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 21
Remove Hand Strap Clip
5. Press the two battery latches in.
6. Lift the battery from the device.
7. Lift the access door.
Figure 22
Remove Access Door
8. Remove card from holder.
Figure 23
Remove SAM Card
9. Insert the replacement card.
Figure 24
Insert SAM Card
Mini SAM Slot
26
10.Replace the access door.
Figure 25
Replace Access Door
Getting Started
11.Press the access door down and ensure that it is properly seated.
CAUTION
:
Access door must be replaced and securely seated to ensure proper device sealing.
12.Insert the battery, bottom first, into the battery compartment in the back of the device.
13.Press the battery down until the battery release latch snaps into place.
14.Replace the hand strap, if required.
15.Press and hold the Power button to turn on the device.
Replacing the microSD Card
To replace the microSD card:
1. Press the Power button until the menu appears.
2. Touch
Power off
.
3. Touch
OK
.
4. If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
Figure 26
Remove Hand Strap Clip
5. Press the two battery latches in.
6. Lift the battery from the device.
27
7. Lift the access door.
Figure 27
Remove Access Door
Getting Started
8. Slide the microSD card holder to the Open position.
9. Lift the microSD card holder.
10.Remove microSD card from holder.
11.Insert the replacement microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
12.Close the microSD card holder door and slide the door to the Lock position.
Figure 28
Close and Lock microSD Card in Holder
13.Replace the access door.
Figure 29
Replace Access Door
14.Press the access door down and ensure that it is properly seated.
CAUTION
:
Access door must be replaced and securely seated to ensure proper device sealing.
15.Insert the battery, bottom first, into the battery compartment in the back of the device.
16.Press the battery down until the battery release latch snaps into place.
28
Getting Started
17.Replace the hand strap, if required.
18.Press and hold the Power button to turn on the device.
29
Using the Device
Home Screen
Turn on the device to display the Home screen. Depending on the configuration, the Home screen may appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock. For screen locking information, see Un-Locking the Screen.
The Home screen provides additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
Figure 30 Home Screen
1 1
2
2
3
4
2
3
4
GMS Non-GMS
30
Using the Device
2
3
4
Table 4 Home Screen Features
1
Item
Status Bar
Description
Displays the time, status icons (right side), and notification icons (left side).
For more information see Status Icons on page 47 and Managing
Notifications on page 50 .
Widgets
Shortcut Icons
Folder
Launches stand-alone apps that run on the Home screen.
Opens apps installed on the device.
Contains apps.
The Home screen provides four additional screens to place widgets and shortcuts. Swipe the screen left or right to view the additional screens.
Setting Home Screen Rotation
By default the
Home
screen rotation is disabled.
To enable
Home
screen rotation:
1. Touch and hold anywhere on the
Home
screen until the options appear.
2. Touch
Home settings
.
3. Touch the
Allow Home screen rotation
switch.
4. Touch .
5. Rotate the device.
Status Bar
The Status bar displays the time, notification icons (left side), and status icons (right side).
NOTE
:
Some Status icons may not appear in the Status bar if there are too many icons to display.
Figure 31
Notification and Status Icons
Notification Icons Status Icons
If there are more notifications than can fit in the Status bar, a dot displays indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
31
Using the Device
Status Icons
Table 5
Status Icons
Icon
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Description
Main battery charge is low.
Main battery charge is very low.
Main battery is charging.
All sounds, except media and alarms, are silenced and vibrate mode is active.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Notification Icons
Table 6
Notification Icons
Icon
Main battery is low.
Description
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. Non-GMS devices only.
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
32
Using the Device
Table 6
Notification Icons (Continued)
Icon
Song is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Description
Device is downloading data when animated and download is complete when static.
Device is connected via USB cable.
Device is connected to or disconnected from virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
Headset is connected to the device.
PTT Express Voice client status. See the PTT Express PTT Notification Icons for a complete list.
Indicates that RxLogger app is running.
Indicates the Bluetooth scanner is connected to the device.
Indicates the RS507/RS507X or RS6000 is connected to the device in HID mode.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons for a list of possible notification icons and their description. Open the Notification panel to view a list of all the notifications.
33
Using the Device
To open the Notification panel, drag the Status bar down from the top of the screen.
Figure 32
Notification Panel
Quick Settings Bar
To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
To manage recent or frequently used notifications, open the Notification panel and then touch
Manage notifications
. Touch the toggle switch next to an app to turn off all notifications, or touch an app for more notification options.
To clear all notifications, open the Notification panel and then touch
CLEAR ALL
. All event-based notifications are removed. Ongoing notifications remain in the list.
To close the Notification panel, swipe the Notification panel up.
Quick Access Panel
Use the Quick Access panel to access frequently used settings (for example, Airplane mode).
To see the full Quick Access panel:
• If the device is locked, swipe down once.
• If the device is unlocked, swipe down once with two fingers, or twice with one finger.
34
Using the Device
• If the Notification panel is open, swipe down from the Quick Settings bar.
Figure 33
Quick Access Panel
NOTE
:
Not all icons are pictured. Icons may vary.
To change a setting, touch the icon:
• Display brightness - Use the slider to decrease or increase the brightness of the screen.
• Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch
Bluetooth
.
• Battery saver - Turn Battery saver mode on or off. When Battery saver mode is on the performance of the device is reduced to preserve battery power.
• Invert colors - Invert the display colors.
• Do not disturb - Control how and when to receive notifications.
• Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to
Wi-Fi or Bluetooth.
• Auto-rotate - Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Flashlight - Turn flashlight on or off. Turn camera flash on or off.
The thermal protection safety feature for the camera provides the following behavior if the temperature range is 40°C or above:
• If the flashlight is kept on for a certain period of time, it is automatically turned off and cannot be turned back on for a period of time until it has cooled off.
• During the cooling off period, the camera cannot be turned on. If you attempt to use the camera, a message displays indicating to try again after a period of time.
• Location - Enable or disable locationing feature.
• Hotspot - Turn on to share the device’s mobile data connection with other devices.
• Data Saver - Turn on to prevent some apps from sending or receiving data in the background.
• Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to turn on automatically from sunset to sunrise, or at other times.
• Cast - Share phone content on Chromecast or a television with Google Cast built-in. Touch cast screen to display a list of devices, then touch a device to begin casting.
35
Using the Device
Editing Icons on Quick Settings
The first several setting tiles from the Quick Access panel become the Quick Settings bar. Open the Quick
Access panel and touch to edit, add, or remove settings tiles.
Battery Management
NOTE
:
Prior to checking the battery charge level, remove the device from any AC power source (cradle or cable).
To check the charge status of the main battery, open
Settings
and touch
About phone
>
Battery
Information
.
Battery present status
indicates if the battery is present and
Battery level
lists the battery charge (as a percentage of fully charged). The battery percentage can also be viewed next to the battery icon in the quick access panel. Swipe down with two fingers from the status bar to open the quick access panel.
Monitoring Battery Usage
The
Battery
screen provides battery charge details and power management options to extend battery life.
1. Go to
Settings
.
2. Touch
Battery
.
To display battery information and power management options for a specific app:
1. Go to
Settings
.
2. Touch
Apps & notifications
.
3. Touch an app.
4. Touch
Advanced
>
Battery
.
Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the
DISABLE
or
FORCE CLOSE
buttons to turn off apps that consume too much power.
Low Battery Notification
When the battery charge level drops below 18%, the device displays a notice to connect the device to power.
The user should charge the battery using one of the charging accessories.
When the battery charge drops below 10%, the device displays a notice to connect the device to power. The user must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the device turns off. The user must charge the battery using one of the charging accessories.
Battery Optimization
Observe the following battery saving tips:
36
Using the Device
• Set the screen to turn off after a short period of non-use.
• Reduce screen brightness.
• Turn off all wireless radios when not in use.
• Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
• Minimize use of apps that keep the device from suspending, for example, music and video apps.
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light:
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
• Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the
Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
• Light Sensor - Detects ambient light and adjusts the screen brightness.
• Proximity Sensor - Detects the presence of nearby objects without physical contact.
In order to take advantage of these sensors, applications use API commands. Refer to the Zebra Android
EMDK for more information.
Suspend Mode
The device goes into suspend mode when you press the Power buttonor after a period of inactivity (set in the
Display settings window).
To wake the device from Suspend mode, press the Power button. The Lock screen displays. Swipe the screen up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen. See Un-Locking the Screen.
NOTE
:
If you enter the PIN, password, or pattern incorrectly five times, you must wait 30 seconds before trying again.
If you forget the PIN, password, or pattern contact your system administrator.
Transferring Files with a Host Computer via USB
Connect the device to a host computer using a USB cable or a USB cradle to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
Transferring Files
NOTE
:
Use Transfer files to copy files between the device (internal memory or microSD card) and the host computer.
1. Connect a USB cable to the device or place the device into a USB cradle.
37
Using the Device
2. Pull down the Notification panel and touch
Charging this device via USB
.
By default,
No data transfer
is selected.
3. Touch
File Transfer
.
NOTE
:
After you change the setting to
File Transfer
, and then disconnect the USB cable, the setting reverts back to
data transfer
. If the USB cable is reconnected, select
File Transfer
again.
No
4. On the host computer, open a file explorer application.
5. Locate the
device
as a portable device.
6. Open the
SD card
or the
Internal storage
folder.
7. Copy files to and from the device or delete files as required.
Transferring Photos
To transfer photos using Photo Transfer Protocol (PTP):
NOTE
:
Use PTP to copy photos from either the microSD card or internal memory to the host computer.
1. Connect USB cable to the device or place the device into a USB cradle. See Accessories for setup information.
2. Pull down the Notification panel and touch
Charging this device via USB
.
3. Touch
PTP
.
4. On the host computer, open a file explorer application.
5. Open the
SD card
or the
Internal storage
folder.
6. Copy or delete photos as required.
Disconnect from the Host Computer
To disconnect the device from the host computer:
CAUTION
:
Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB devices cor rectly to avoid losing information.
-
1. On the host computer, unmount the device.
2. Remove the USB cable from the device or remove the device from the cradle.
38
Settings
Accessing Settings
Access Settings in any of the following ways:
• Swipe down with two fingers from the top of the Home screen to open the Quick Access panel and touch
.
• Double-swipe down from the top of the Home screen to open the Quick Access panel and touch
.
• Swipe up from the bottom of the Home screen to open APPS and touch
Settings
.
Display Settings
Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, set sleep time, and change font size.
Setting the Screen Brightness
To manually set the screen brightness using the touchscreen:
1. Swipe down with two fingers from the Status bar to open the Quick Access panel.
2. Slide the icon to adjust the screen brightness level.
To let the device automatically adjust the screen brightness using the built-in light sensor:
1. Go to
Settings
.
2. Touch
Display
.
3. If disabled, touch
Adaptive brightness
to automatically adjust the brightness.
By default,
Adaptive brightness
is enabled. Toggle the switch to disable.
4. Touch .
Setting Night Light
The Night Light setting tints the screen amber, making the screen easier to look at in low light.
To enable night light:
1. Go to
Settings
.
39
Settings
2. Touch
Display
.
3. Touch
Night Light
.
4. Touch
Schedule
.
5. Select one of the schedule values:
• None (default)
• Turns on at custom time
• Turns on from sunset to sunrise.
6. By default,
Night Light
is disabled. Touch
TURN ON NOW
to enable.
7. Adjust the tint using the
Intensity
slider.
8. Touch .
Setting Screen Rotation
By default, screen rotation is enabled.
To disable screen rotation:
1. Go to
Settings
.
2. Touch
Display
>
Advanced
.
3. Touch
Auto-rotate screen
.
NOTE
:
To change the Home screen rotation, see Setting Home Screen Rotation.
4. Touch .
Setting Screen Timeout
To set the screen sleep time:
1. Go to
Settings
.
2. Touch
Display
>
Advanced
>
Sleep
.
3. Select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute
(default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
4. Touch .
40
Settings
Ambient Display
The Ambient display setting wakes the screen when notifications are received.
To disable ambient display:
1. Go to
Settings
.
2. Touch
Display
>
Advanced
.
3. Touch
Ambient display
.
4. In the
When to show
section, enable or disable an option using the switch.
5. Touch .
Setting Touch Key Light
The four touch keys under the screen are backlit.
To configure the touch key light to save battery power:
1. Go to
Settings
.
2. Touch
Display
>
Advanced
.
3. Touch
Touch key light
.
4. Select an option to choose how long the touch key light stays on:
• Always off
• 6 seconds (default)
• 10 seconds
• 15 seconds
• 30 seconds
• 1 minute
• Always on.
5. Touch .
Setting Font Size
To set the size of the font in system apps:
1. Go to
Settings
.
2. Touch
Display
>
Advanced
.
3. Touch
Font size
.
4. Select one of the font size values.
• Small
• Default
• Large
• Largest.
41
Settings
5. Touch .
Touch Panel Mode
The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
NOTE
:
A glove can be made of medical latex, leather, cotton, or wool.
For optimal performance use a Zebra certified stylus.
1. Go to
Settings
.
2. Touch
Display
>
Advanced
.
3. Touch
Touch panel mode
.
4. Select: a.
Glove and Finger (Screen Protector off)
to use a finger or a gloved finger on the screen without a screen protector.
b.
Stylus and Finger (Screen Protector off)
to use a finger or a stylus on the screen without a screen protector.
c.
Finger Only (Screen Protector off)
to use a finger on the screen without a screen protector.
d.
Glove and Finger (Screen Protector on)
to use a finger or a gloved finger on the screen with a screen protector.
e.
Stylus and Finger (Screen Protector on)
to use a finger or a stylus on the screen with a screen protector.
5. Touch .
Setting the Date and Time
You are only required to set the time zone or set the date and time if the wireless LAN does not support
Network Time Protocol (NTP).
To set the date and time:
1. Go to
Settings
.
2. Touch
System
>
Date & time
.
3. Touch
Automatic date & time
to disable automatic date and time synchronization.
4. Touch
Set date
.
5. In the calendar, set today’s date.
6. Touch
OK
.
7. Touch
Set time
.
8. Touch the green circle, drag to the current hour and then release.
9. Touch the green circle, drag to the current minute and then release.
10.Touch
AM
or
PM
.
11.Touch
OK
.
12.Touch
Use 24-hour format
.
42
Settings
13.Touch .
General Sound Setting
Use the
Sound
settings to configure media and alarm volumes.
To access sound settings:
1. Go to
Settings
.
2. Touch
Sound
.
3. Touch an option to set sounds.
Sound Options
• Zebra volume controls
•
Ring volume
- Controls the ringtone volume.
•
Media volume
- Controls the music, games, and media volume.
•
Alarm volume
- Controls the alarm clock volume.
•
Notifications volume
- Controls the notification volume.
• Scanner volume
- Controls the scanner volume.
• Volume presets
•
• - Mutes the ring, notifications, and scanner so that the device does not make sounds or vibrate.
- All sounds except media and alarms are silenced and vibrate mode is active.
• - Enables all sounds at the user defined levels.
• Also vibrate for calls - Switch on or off.
•
Do Not Disturb preferences
- Mutes some or all sounds and vibrations.
• Shortcut to prevent ringing
- Select how the shortcut method prevents ringing.
•
Phone ringtone
- Select a sound to play when the phone rings.
•
Default notification sound
- Select a sound to play for all system notifications.
•
Default alarm sound
- Select a sound to play for alarms.
• Other sounds and vibrations
•
Dial pad tones
- Play a sound when pressing keys on dial pad (default - disabled).
•
Screen locking sounds
- Play a sound when locking and unlocking the screen (default – enabled).
•
Advanced
- Touch to display advanced sound options.
•
Charging sounds
- Not applicable.
•
Touch sounds
- Play a sound when making screen selections (default – enabled).
•
Touch vibration
- Vibrate the device when making screen selections (default – disabled).
•
Wireless Emergency alerts
- Touch to configure emergency broadcast settings and notifications.
Wake-Up Sources
By default the device wakes from suspend mode when the user presses the
Power
button. The device can be configured to wake when the user presses the
PTT
or
Scan
buttons on the left side of the device.
43
Settings
To configure wake-up sources:
1. Go to
Settings
.
2. Touch
Wake-Up Sources
.
3. Select the
SCAN
checkbox to use the left Scan button to wake the device.
4. Select the
RIGHT_TRIGGER_1
checkbox to use the right Scan button to wake the device.
5. Select the
LEFT_TRIGGER_2
checkbox to use the PTT button to wake the device.
6. Select the
GUN_TRIGGER
checkbox to use any Scan button, or the Trigger Handle to wake the device.
7. Touch .
Remapping a Button
Buttons on the device can be programmed to perform different functions or as shortcuts to installed apps. For a list of key names and descriptions, refer to techdocs.zebra.com
.
NOTE
:
It is not recommended to remap the scan button.
1. Go to
Settings
.
2. Touch
Key Programmer
. A list of programmable buttons displays.
3. Select the button to remap.
4. Touch the
BUTTON REMAPPING
tab or the
SHORTCUT
tab that lists the available functions and applications.
5. Touch a function or application shortcut to map to the button.
NOTE
:
If you select an application shortcut, the application icon appears next to the button on the Key Programmer screen.
6. Touch .
7. If remapping the Back, Home, Search, or Menu button, perform a Soft Reset.
Keyboards
The device provides the following types of keyboards:
• Android Keyboard - Non-GMS devices only.
• Gboard - GMS devices only
• Enterprise Keyboard
NOTE
:
By default the Enterprise and Virtual Keyboards are disabled.
Keyboard Configuration
Enabling Keyboards
To enable keyboards:
44
Settings
1. Go to
Settings
.
2. Touch
System
>
Languages & input
>
Virtual keyboard
>
Manage keyboards
.
3. Touch a keyboard to enable.
Switching Between Keyboards
To switch between keyboards, touch in a text box to display the current keyboard.
• On the Android or Gboard keyboards, touch and hold .
• On the Enterprise keyboard, touch .
Using the Android and Gboard Keyboards
Use the Android or Gboard keyboards to enter text in a text field. To configure the keyboard settings, touch and hold
,
(comma) and then select
Android keyboard settings
.
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across apps. Some apps do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols, and Special Characters
To enter numbers and symbols:
• Touch and hold one of the top-row keys until a menu appears then select a number or special character.
• Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch the
Shift key a third time to unlock Capslock.
• Touch
?123
to switch to the numbers and symbols keyboard.
• Touch the
=\<
key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols. A larger version of the key displays briefly over the keyboard.
Using the Enterprise Keyboard
The Enterprise Keyboard contains the following keyboards:
• Numeric
• Alpha
• Special characters
• Data capture.
45
Settings
Numeric Tab
To access the numeric keyboard, touch the
123
tab. The keys displayed vary on the app being used. For example, an arrow displays in
Contacts
, however
Done
displays in
account setup.
Figure 34
Numeric Keyboard
Alpha Tab
To access the alpha keyboard, touch the EN tab.
Figure 35
Alpha Keyboard
Additional Character Tab
To access additional characters, touch the
#*/
tab.
Figure 36
Symbols Keyboard
46
Settings
Touch to enter emoji icons in a text message.
Figure 37
Emoji Keyboard
Touch
ABC
to return to the Symbols keyboard.
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Figure 38
Scan Keyboard
Language Usage
Use the
Language & input
settings to change the device’s language, including words added to the dictionary.
Changing the Language Setting
1. Go to
Settings
.
2. Touch
System
>
Languages & input
.
3. Touch
Languages
. A list of available languages displays.
4. If the desired language is not listed, touch
Add a language
and select a language from the list.
5. Touch and hold to the right of the desired language, then drag it to the top of the list.
6. The operating system text changes to the selected language.
Adding Words to the Dictionary
1. Go to
Settings
.
2. Touch
System
>
Languages & input
>
Advanced
>
Personal dictionary
.
47
Settings
3. If prompted, select the language where this word or phase is stored.
4. Touch
+
to add a new word or phrase to the dictionary.
5. Enter the word or phrase.
6. In the
Shortcut
text box, enter a shortcut for the word or phrase.
7. Touch .
48
Applications
The
APPS
screen displays icons for all installed apps. The table below lists the apps installed on the device. See Application Deployment for information on installing and uninstalling apps. For information on standard Android apps, go to support.google.com
.
Table 7 Apps
Icon Description
Battery Manager
- Displays battery information, including charge level, status, health and wear level.
Battery Swap
– Use to place device in Battery Swap mode when replacing the battery.
Bluetooth Pairing Utility
– Use to pair the RS507 Hands-free Imager with the device by scanning a barcode.
Calculator
- Provides the basic and scientific arithmetic functions.
Calendar
- Use to manage events and appointments. GMS/GMS-Restricted only.
Calendar
- Use to manage events and appointments. AOSP only.
Camera
- Take photos or record videos. For more information see Camera.
Chrome
- Use to access the Internet or intranet. GMS/GMS-Restricted only
Chromium
- Use to access the Internet or intranet. AOSP only.
49
Applications
Table 7 Apps (Continued)
Icon Description
Clock
- Use to schedule alarms for appointments or as a wake-up.
Contacts
- Use to manage contact information. See Contacts for more information.
DataWedge
- Enables data capture using the imager.
Diagnostic Tool
- Use to diagnose the device.
Drive
- Upload photos, videos, documents, and other files to personal storage site.
GMS/GMS-Restricted only.
Duo
- A one-to-one video calling app. GMS/GMS-Restricted only.
DWDemo
- Provides a way to demonstrate the data capture features using the imager.
See DataWedge Demonstration for more information.
- Use to send and receive email. AOSP only.
Files
- Organize and manage files on the device. See Files for more information.
Gallery
- Use to view photos stored on the microSD card. For more information, see
Gallery for more information. AOSP only.
Gmail
- Use to send and receive email using a Google email account.
GMS/GMS-Restricted only
- Launches Google ™ search app. GMS/GMS-Restricted only
Keep
- Use to create, edit, and share notes. GMS/GMS-Restricted only.
License Manager
- Use to manage software licenses on the device.
50
Applications
Table 7 Apps (Continued)
Icon Description
Maps
- Use to see your location on a map (with public transit, traffic, or satellite overlays). Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance, traffic-avoidance, and alternate routes, for drivers, cyclists, walkers, and users of public transportation. GMS/GMS-Restricted only.
MSRN
- Use to verify authenticity of the paired Snap-on MSR and to provision the
Snap-on MSR.
Music
- Play music stored on the microSD card. AOSP only.
Photos
- Use to sync photos with Google account. For more information, see Photo
Settings. GMS/GMS-Restricted only.
Play Movies & TV
- View movies and video on your device. GMS/GMS-Restricted only.
Play Music
- Use to listen to music. GMS/GMS-Restricted only.
Play Store
- Download music, movies, books, and Android apps and games from the
Google Play Store. GMS/GMS-Restricted only.
PTT Express
- Use to launch PTT Express client for VoIP communication.
RxLogger
- Use to diagnose device and app issues. See the device Integrator Guide for Android Version 8.1 for more information.
RxLogger Utility
- Use to view, backup, and archive RxLogger data.
Search
- Use to search the Web. Requires an Internet connection. AOSP only.
Settings
- Use to configure the device.
SimulScan Demo
- Use to demonstrate the document capture feature of the device.
Sound Recorder
- Use to record audio.
51
Applications
Table 7 Apps (Continued)
Icon Description
StageNow
- Allows the device to stage a device for initial use by initiating the deployment of settings, firmware, and software.
Worry Free Wifi Analyzer
- A diagnostic intelligent app. Use to diagnose surrounding area and display network stats, such as coverage hole detection, or AP in vicinity. Refer to the Worry Free Wi-Fi Analyzer Administrator Guide for Android.
YouTube
- Use to view videos on the YouTube
™
web site. GMS/GMS-Restricted only.
Zebra Bluetooth
- Use to configure Bluetooth logging.
Accessing Apps
All apps installed on the device are accessed using the
APPS
window.
1. On the Home screen, swipe up from the bottom of the screen.
2. Slide the
APPS
window up or down to view more app icons.
3. Touch an icon to open the app.
Switching Between Recent Apps
To switch between recent apps:
1. Touch . A window appears on the screen with icons of recently used apps.
2. Slide the apps displayed up and down to view all recently used apps.
3. Swipe left or right to remove app from the list and force close the app.
4. Touch an icon to open an app or touch to return to the current screen.
Battery Manager
The
Battery Manager
provides detailed information about the battery.
To open Battery Manager, swipe up from the bottom of the Home screen and touch .
52
Applications
Table 8 Battery Icon Description
Battery
Icon
Battery charge level.
Description
Battery charging.
Battery charge level is below 20%.
•
Battery level
- The current battery charge level as a percentage. Displays
-%
when level is unknown.
•
Time until full
- The amount of time until the battery is fully charged.
•
Time since charging
- The amount of time since the device began charging.
•
Time until empty
- The amount of time until the battery is empty.
• Battery status
•
Not charging
- The device is not connected to AC power.
•
Charging over AC
- The device is connected to AC power and charging.
•
Charging over USB
- The device is connected to a host computer with a USB cable and charging.
•
Discharging
- That the battery is discharging.
•
Full
- That the battery is fully charged.
•
Unknown
- The battery status is unknown.
•
Battery health
- The health of the battery. If a critical error occurs, appears. Touch to view the error description.
•
Decommission
- The battery is past its useful life and should be replaced. See system administrator.
•
Good
- The battery is good.
•
Charge error
- An error occurred while charging. See system administrator.
•
Over Current
- An over-current condition occurred. See system administrator.
•
Dead
- The battery has no charge. Replace the battery.
•
Over Voltage
- An over-voltage condition occurred. See system administrator.
•
Below Temperature
- The battery temperature is below the operating temperature. See system administrator.
•
Failure Detected
- A failure has been detected in the battery. See system administrator.
•
Unknown
- See system administrator.
•
Wear level
- The health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
53
Applications
•
Advanced info
- Touch to view additional battery information.
•
Battery present status
- Indicates that the battery is present.
•
Battery level
- The battery charge level as a percentage of scale.
•
Battery scale
- The battery scale level used to determine battery level (100).
•
Battery voltage
- The current battery voltage in millivolts.
•
Battery temperature
- The current battery temperature in degrees Centigrade.
•
Battery technology
- The type of battery.
•
Battery current
- The average current into or out of the battery over the last second in mAh.
•
Battery manufacture date
- The date of manufacture.
•
Battery serial number
- The battery serial number. The number matches the serial number printed on the battery label.
•
Battery part number
- The battery part number.
•
Battery rated capacity
- Lists the rated capacity of the backup battery in mAh.
•
Battery decommission status
- Indicates if the battery is past its life span.
•
Battery Good
- The battery is in good health.
•
Decommissioned Battery
- The battery is past its useful life and should be replaced.
•
Base cumulative charge
- Cumulative charge using Zebra charging equipment only.
•
Battery present capacity
- Maximum amount of charge that could be pulled from the battery under the present discharge conditions if the battery were fully charged.
•
Battery health percentage
- With a range from
0
to
100
, this is the ratio of “present_capacity” to
“design_capacity” at a discharge rate of “design_capacity”.
•
% decommission threshold
- The default % decommission threshold for a gifted battery as 80%.
•
Battery present charge
Amount of usable charge remaining in the battery at present under the current discharge conditions.
•
Battery total cumulative charge
The total accumulated charge in all chargers.
•
Battery time since first use
The time passed since the battery was placed in a Zebra terminal for the first time.
•
Battery error status
- The error status of the battery.
•
App version
- The application version number.
54
Applications
Camera
This section provides information for taking photos and recording videos using the integrated digital cameras.
The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.
Taking Photos
NOTE
:
See Photo Settings for camera setting descriptions.
1. Swipe up from the bottom of the Home screen and touch
Camera
.
Figure 39
Camera Mode
Filters
Scene Mode
Camera Switch
HDR
Settings
Gallery Camera Mode
Shutter Button
2. If necessary, touch the Camera Mode icon and touch .
3. To switch between the rear camera and front camera (if available), touch .
4. Frame the subject on the screen.
55
Applications
5. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6. Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
7. Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Taking a Panoramic Photo
Panorama mode creates a single wide image by panning slowly across a scene.
1. Swipe up from the bottom of the Home screen and touch
Camera
.
Figure 40
Panoramic Mode
2. Touch the Camera Mode icon and touch .
3. Frame one side of the scene to capture.
4. Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message
Too fast
appears.
5. Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
56
Applications
Recording Videos
1. Swipe up from the bottom of the Home screen and touch
Camera
.
2. Touch the camera mode menu and touch .
Figure 41
Video Mode
Camera Switch (Available on devices with a rear camera and front camera)
Audio
Settings
Gallery
Camera Mode
Shutter Button
3. To switch between the rear camera and front camera (if available), touch .
4. Point the camera and frame the scene.
5. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6. Touch to start recording.
The video time remaining appears in the top left of the screen.
7. Touch to the end recording.
The video momentarily displays as a thumbnail in the lower left corner.
57
Applications
Photo Settings
In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
Rear Camera
•
Flash
- Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
•
•
Off
On
- Disable flash.
Auto
- Adjust flash automatically depending upon light meter (default).
- Enable flash upon taking a photo.
•
Torch
- Turn flash on continuously.
•
Picture size
- The size (in pixels) of the photo to:
13M pixels
(default),
8M pixels
,
5M pixels
,
3M pixels
,
HD 1080
,
2M pixels
,
HD720
,
1M pixels
,
WVGA
,
VGA,
or
QVGA
.
•
Picture quality
- Set the picture quality setting to:
Low
,
Standard
(default) or
High
.
•
Countdown timer
- Select
Off
(default),
2 seconds
,
5 seconds
or
10 seconds
.
•
Storage
– Set the location to store the photo to:
Phone
or
SD Card
.
•
Face Detection
- Select to turn face detection
Off
(default) or
On
.
•
ISO
- Set camera sensitivity to light to:
Auto
(default),
ISO Auto (HJR)
,
ISO100
,
ISO200
,
ISO400
,
ISO800
or
ISO1600
.
•
Exposure
- Set the exposure settings to:
+2
,
+1
,
0
(default),
-1
or
-2
.
•
White balance
- Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
Incandescent
- Adjust the white balance for incandescent lighting.
•
•
Fluorescent
- Adjust the white balance for florescent lighting.
Auto
- Adjust the white balance automatically (default).
•
Daylight
- Adjust the white balance for daylight.
•
Cloudy
- Adjust the white balance for a cloudy environment.
•
ZSL
- Set the camera to immediately take a picture when the button is pressed (default – enabled).
•
Anti Banding
- Allows the camera to avoid problems caused by artificial light sources that are not constant.
These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options:
Auto
(default),
60 Hz
,
50 Hz
, or
Off
.
Front Camera
•
Picture size
- Set the size (in pixels) of the photo to:
5M pixels
(default),
HD720
,
1M pixels
,
WVGA
,
VGA,
or
QVGA
.
•
Picture quality
- Set picture quality setting to:
Low
,
Standard
(default) or
High
.
•
Countdown timer
- Set to:
Off
(default),
2 seconds
,
5 seconds
or
10 seconds
.
•
Storage
– Set location to store the photo to:
Phone
or
SD Card
.
•
Face Detection
- Select to turn face detection
Off
(default) or
On
.
58
Applications
Video Settings
In Video mode, video settings appear on screen. Touch to display the video settings options.
Rear Camera
•
•
•
•
•
•
Flash
- Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
Off
- Disable flash (default).
•
Torch
- Turn flash on continuously.
•
Video quality
- Set video quality to:
4k DCI
,
4k UHD
,
HD 1080p
(default),
HD 720p
,
SD 480p, VGA, CIF, or QVGA
.
•
Video duration
- Set to:
30 seconds (MMS)
, or
30 minutes
(default).
•
Storage
– Set the location to store the photo to:
Phone
(default) or
SD Card
.
•
White balance
- Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
Incandescent
Cloudy
- Adjust the white balance for incandescent lighting.
Fluorescent
- Adjust the white balance for florescent lighting.
Auto
- Adjust the white balance automatically (default).
Daylight
- Adjust the white balance for daylight.
- Adjust the white balance for a cloudy environment.
Front Camera
•
Video quality
- Set video quality to:
HD 720p
(default), or
SD 480p
.
•
Video duration
- Set to:
30 seconds (MMS)
or
30 minutes
(default).
•
Storage
– Set the location to store the photo to:
Phone
(default) or
SD Card
.
59
Applications
DataWedge Demonstration
NOTE
:
DataWedge is disabled on the Home screen.To enable this feature, go to the DataWedge settings and enable Bar code input option.
-
Use
DataWedge Demonstration
to demonstrate data capture functionality.
Table 9 DataWedge Demonstration Icons
Icon
Illumination
Description
Imager illumination is on. Touch to turn illumination off.
Data Capture
Imager illumination is off. Touch to turn illumination on.
The data capture function is through the internal imager.
An RS507 or RS6000 Bluetooth imager is connected.
Scan Mode
An RS507 or RS6000 Bluetooth imager is not connected.
Imager is in picklist mode. Touch to change to normal scan mode.
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
NOTE
:
To configure DataWedge, refer to techdocs.zebra.com/datawedge/ .
Scanner Selection
To select a scanner, touch >
Settings
>
Scanner selection
.
See Data Capture for more information.
Either press the programmable button or touch the yellow scan button to capture data. The data appears in the text field below the yellow button.
60
Applications
Device Central
Device Central
displays detailed information about the device and connected peripherals and supports the following Zebra devices:
• RS507/RS507X Hands-free Imager
• RS6000 Bluetooth Ring Scanner
• RS5000 Corded Ring Scanner
• HS3100 Bluetooth Headset
• DS3678 Digital Scanner.
Device Central features include:
• Discovering and pairing with supported peripherals via Bluetooth or corded connection.
• Paging a connected RS6000 Ring Scanner.
• Updating the firmware of supported ring scanners. Refer to the RS5000 Quick Start Guide or RS6000 User
Guide for more information.
• Displaying the connection status of peripherals.
• Displaying information for a connected peripheral in the notification bar.
Figure 42
Device Central Screen
Scan and Pair Tab
Pairing to a Bluetooth peripheral is accomplished by one of the following methods:
• Scan and Pair
• Scan to Pair
• Manually Pairing.
Scan and Pair
To scan the peripheral Bluetooth barcode to pair:
1. In the
Scan and Pair
tab, touch
Scan barcode to pair
. The peripheral’s scan beam illuminates.
61
Applications
2. Ensure that Bluetooth is enabled on the peripheral and is set to discoverable mode. Refer to the peripheral user guide for instructions.
3. Scan the Bluetooth MAC address barcode label on the desired peripheral to pair.
When pairing is successful, the peripheral displays in the list. A green dot appears next to a Bluetooth scanner when the device is connected, and may be in use. A red dot appears next to other Bluetooth peripherals, such as a Bluetooth headset or printer, while they are connected but not in use.
Scan to Pair
Use Scan and Pair to pair by scanning a barcode displayed on the screen. This applies to peripherals that have scanning capability, such as Bluetooth handheld scanners and ring scanners.
1. In the
Scan and Pair
tab, touch
Display barcode to pair
. A barcode displays.
2. Using the peripheral, scan the barcode on the screen.
When the pairing is successful, the peripheral displays in the list with a green dot indicating that it is paired.
Manually Pairing
To manually pair a peripheral that is unable to pair via Bluetooth:
1. In the
Scan and Pair
tab, touch the
MAC address
field.
2. Enter the Bluetooth MAC address of the peripheral.
3. Touch
Pair
.
When pairing is successful, the peripheral displays in the list. A green dot appears next to a Bluetooth scanner when the device is connected, and may be in use. A red dot appears next to other Bluetooth peripherals, such as a Bluetooth headset or printer, while they are connected but not in use.
Peripherals Tab
The
Peripherals
Tab displays all currently connected and previously connected peripherals. Connected peripherals display the length of time (in minutes) that they have been connected.
Touch the connected device icon to display details about the peripheral. The
Device Details
screen appears.
When an RS6000 is connected the
Page
button displays at the bottom of the
Device Details
screen. See
Paging an RS6000 Ring Scanner.
My Device Tab
The
My Device
Tab displays information about the device.
•
Device Model
- Displays the name assigned to the device.
•
Device Serial Number
- Displays the serial number of the device.
•
OS Version
- Displays the operating system version.
•
Build Number
- Displays the software build number.
•
Battery Level
- The current battery charge level as a percentage.
•
Battery Part Number
- The battery part number.
•
Battery Serial Number
- The battery serial number. The number matches the serial number printed on the battery label.
•
Battery Manufactured Date
- The date of manufacture.
62
Applications
Unpairing a Peripheral
To unpair a Bluetooth peripheral:
1. In the
Scan and Pair
tab, touch
Unpair
for the desired peripheral to unpair.
A confirmation pop-up message appears.
2. Touch
OK
.
Once unpaired, a message appears indicating the peripheral has been disconnected, and the peripheral is removed from the list.
Paging an RS6000 Ring Scanner
Use
Page
button to easily locate the currently connected RS6000 Ring Scanner:
1. With the RS6000 Ring Scanner connected, swipe up from the bottom of the Home screen, and touch .
NOTE
:
The RS6000 Ring Scanner must be within 10 m (32 ft) of the device.
2. Touch RS6000. The Device Details screen displays.
3. Under the RS6000 peripheral information, touch
Page
to page the RS6000. The paged RS6000 beeps and vibrates.
Figure 43
Page RS6000
To stop paging, press the scan trigger of the RS6000. On a triggerless RS6000, reset the RS6000 to stop paging. Refer to the RS6000 User Guide.
63
Applications
Diagnostic Tool
The
Diagnostic Tool
is a utility that determines the health of the device. Use the Diagnostic Tool to troubleshoot the device.
1. Swipe up from the bottom of the Home screen and touch .
2. Touch
RUN TEST
. The app tests all enabled subsystems (by default, only the Battery and System tests).
See Settings to enable subsystem tests.
3. To view each subsystem test, touch
Subsystem Tests
.
Figure 44
Subsystem Screen
4. Touch one of the subsystems to view details.
Table 10 Subsystem Test Result Indicators
Status Icon Description
Test passed.
Test failed.
Test not supported or not enabled.
Settings
By default only the Battery and System tests are enabled. To enable other tests:
64
Applications
1. Touch >
Settings
.
2. Touch to the left of the test name. A green box with a checkmark appears.
3. Touch
SAVE
.
4. Touch
Yes
to confirm.
5. Touch .
Battery Test Information
The Battery Test obtains the following information:
•
Battery Level
- Current battery charge level
•
Battery Voltage
- Current battery voltage
•
Status
- Whether the battery is charging (on AC power) or discharging (on battery power)
•
Power Source
- Whether the device is receiving power from the battery or from an external source
•
Temperature
- Current battery temperature
•
Health Percentage
- Indicates the ratio of present capacity to design capacity at a discharge rate of design capacity.
•
Backup Battery Voltage
- Backup battery voltage.
•
Manufacture Date
- Manufacture date of the battery.
GPS Test Information
Not supported on this device.
System Test Information
Use the System Test to determine if the CPU or memory loads are too high, there are too many processes running on the device, or storage on the device is almost full.
The System Test obtains the following information:
•
CPU Load
- Amount of CPU being used
•
Free Physical Memory
- Amount of RAM available
•
Free Storage
- Amount of internal Flash memory available
•
Process Count
- Number of processes currently running.
WLAN Test Information
If the WiFi radio is not present or disabled, skip this test. This test determines if the device’s WLAN configuration is correct or whether there is any connection with an access point or network.
The WLAN test obtains the following information:
•
WLAN Enabled
- WLAN radio is enabled or disabled
•
WLAN Status
- Current status of association with the access point
•
ESSID
- Name of the wireless network
65
Applications
•
BSSID
- MAC address of the connected access point
•
MAC Address
- Device’s MAC address
•
Signal
- Strength of the Wi-Fi signal (in dBm)
•
IP Address
- IP address of the device.
WWAN Test Information
Not supported on this device.
Bluetooth Test Information
The Bluetooth Test obtains the following information:
•
Enabled
- Whether the Bluetooth radio is enabled or disabled
•
Status
- Whether the device is paired to another Bluetooth device
•
Connectable/Discoverable
- Whether the device is discoverable or able to connect
•
Address
- Bluetooth radio MAC address
•
Name
- Bluetooth name for the device.
66
Applications
PTT Express Voice Client
NOTE
:
PTT Express Voice Client enables Push-To-Talk (PTT) communication between disparate enterprise devices. Le veraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without requiring a voice communication server.
-
•
Group Call
: Press and hold the PTT (Talk) button to start communicating with other voice client users.
•
Private Response
: Double-press the PTT button to respond to the originator of the last broadcast or to make a Private Response.
PTT Express User Interface
Figure 45
PTT Express Default User Interface
Notification Icon
Service Indication
Settings
Enable/Disable Switch
Talk Group
Table 11 PTT Express Default User Interface Descriptions
Item
Notification Icon
Service Indication
Talk Groups
Settings
Enable/Disable
Switch
Indicates the current state of the PTT Express client.
Indicates the status of the PTT Express client. Options:
Disabled
or
Service Unavailable
.
Description
Service Enabled
Lists all 32 Talk Groups available for PTT communication.
Opens the PTT Express Settings screen.
Turns the PTT service on and off.
,
Service
67
Applications
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
•
Talk Tone
: Double chirp. Plays when the Talk button is depressed. This is a prompt for you to start talking.
•
Access Tone
: Single beep. Plays when another user just finished a broadcast or response. You can now initiate a Group Broadcast or Private Response.
•
Busy Tone
: Continuous tone. Plays when the Talk button is depressed and another user is already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
•
Network Tone
:
• Three increasing pitch beeps. Plays when PTT Express acquires the WLAN connection and the service is enabled.
• Three decreasing pitch beeps. Plays when PTT Express loses the WLAN connection or the service is disabled.
PTT Notification Icons
Notification icons indicate the current state of the PTT Express Voice client.
Table 12 PTT Express Icon Descriptions
Status Icon Description
The PTT Express Voice client is disabled.
The PTT Express Voice client is enabled but not connected to a WLAN.
The PTT Express Voice client is enabled, connected to a WLAN, and listening on the Talk
Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and communicating on the
Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and in a private response.
The PTT Express Voice client is enabled and muted.
The PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call in progress.
Enabling PTT Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the
Enable/Disable Switch
to the
ON
position. The button changes to
ON
.
68
Applications
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE
:
This section describes the default PTT Express client configuration. Refer to the PTT Express V1.2 User Guide for detailed information on using the client.
Figure 46
PTT communication may be established as a Group Call. When PTT Express is enabled, the PTT button on the left side of the device is assigned for PTT communication. When the Wired Headset is used,
Group Calls can also be initiated using the headset Talk button.PTT Button
PTT Button
Creating a Group Call
1. Press and hold the PTT button (or the Talk button on the headset) and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that
PTT Express and the WLAN are enabled.
2. Start talking after hearing the talk tone.
NOTE
:
Holding the button for more than 60 seconds (default) drops the call, allowing others to make Group calls. Release the button when finished talking to allow others to make calls.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private
Response is made to the originator of the Group Call.
1. Wait for an access tone.
2. Within 10 seconds, double-press the PTT button, and listen for the talk tone.
69
Applications
3. If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that
PTT Express and the WLAN are enabled.
4. Start talking after the talk tone plays.
5. Release the button when finished talking.
Disabling PTT Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the
Enable/Disable Switch
to the
OFF
position. The button changes to
OFF
.
3. Touch .
70
Applications
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics, allows for the creation of custom plug-ins, and diagnoses device and application issues. RxLogger logs the following information: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat, FTP push/pull, ANR dumps, etc. All generated logs and files are saved onto flash storage on the device (internal or external).
RxLogger Configuration
RxLogger is built with an extensible plug-in architecture and comes packaged with a number of plug-ins already built-in. For information on configuring RxLogger, refer to techdocs.zebra.com/rxlogger/ .
To open the configuration screen, from the RxLogger home screen touch
Settings
.
Configuration File
RxLogger configuration can be set using an XML file. The
config.xml
configuration file is located on the microSD card in the
RxLogger\config
folder. Copy the file from the device to a host computer using a USB connection. Edit the configuration file and then replace the XML file on the device. There is no need to stop and restart the RxLogger service since the file change is automatically detected.
Enabling Logging
To enable logging:
1. Swipe the screen up and select .
2. Touch
Start
.
3. Touch .
Disabling Logging
To disable logging:
1. Swipe the screen up and select .
2. Touch
Stop
.
3. Touch .
Extracting Log Files
1. Connect the device to a host computer using an USB connection.
2. Using a file explorer, navigate to the
RxLogger
folder.
3. Copy the file from the device to the host computer.
4. Disconnect the device from the host computer.
71
Applications
Backup
RxLogger Utility allows the user to make a zip file of the
RxLogger
folder in the device, which by default contains all the RxLogger logs stored in the device.
To save the backup data, touch >
BackupNow
.
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the device while RxLogger is running. Logs and RxLogger Utility features are accessed using Main Chat Head.
Initiating the Main Chat Head
To initiate the Main Chat Head:
1. Open
RxLogger
.
2. Touch >
Toggle Chat Head
. The Main Chat Head icon appears on the screen.
3. Touch and drag the Main Chat head icon to move it around the screen.
Removing the Main Chat Head
To remove the Main Chat Head icon:
1. Touch and drag the icon. A circle with an X appears.
2. Move the icon over the circle and then release.
Viewing Logs
To view logs:
1. Touch the Main Chat Head icon. The RxLogger Utility screen appears.
2. Touch a log to open it. The user can open many logs with each displaying a new sub Chat Head.
3. If necessary, scroll left or right to view additional Sub Chat Head icons.
4. Touch a Sub Chat Head to display the log contents.
Removing a Sub Chat Head Icon
To remove a sub chat Head icon, press and hold the icon until it disappears.
Backing Up In Overlay View
RxLogger Utility allows the user to make a zip file of the
RxLogger
folder in the device, which by default contains all the RxLogger logs stored in the device.
The Backup icon is always available in Overlay View.
1. Touch . The Backup dialog box appears.
2. Touch
Yes
to create the back up.
72
Applications
Sound Recorder
Use
Sound Recorder
to record audio messages.
Recordings are saved on the microSD card (if installed) or the internal storage and are available in the Music application (non-GMS devices) or the Play Music application (GMS devices).
Touch to open options menu.
•
File type
- Select the file type for the recording file.
• AMR
• 3GPP
• AAC
• WAV
• AMR-WB
•
AMR-WB-3GPP
.
•
Storage location
- Select the location for the recording file.
• Phone storage
•
SD card
.
73
Data Capture
Introduction
The device supports data capture using:
• Integrated Imager
• Integrated Camera
• RS507/RS507X Hands-free Imager
• RS6000 Bluetooth Ring Scanner
• DS3578 Digital Scanner
• DS3608 Digital Scanner
• DS3678 Digital Scanner.
Integrated Imager
The device with an integrated 2D imager has the following features:
• Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal, PDF417, Digimarc, and 2D matrix code types.
• The ability to capture and download images to a host for a variety of imaging applications.
• Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a barcode, stores the resulting image in memory, and executes state-of-the-art software decoding algorithms to extract the barcode data from the image.
Operational Modes
The device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing the Scan button.
• Decode mode - The device attempts to locate and decode enabled barcodes within its field of view.
The imager remains in this mode as long as you hold the scan button, or until it decodes a barcode.
NOTE
:
To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
• Pick List mode - Selectively decode a barcode when more than one barcode is in the device’s field of view by moving the aiming crosshair or dot over the required barcode. Use this feature for pick
74
Data Capture lists containing multiple barcodes and manufacturing or transport labels containing more than one barcode type (either 1D or 2D).
Digital Camera
The device with an integrated camera based barcode scanning solution has the following features:
• Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal, QR,
PDF417, and 2D matrix code types.
• Cross-hair reticle for easy point-and-shoot operation.
• Picklist mode to decode a particular barcode from many in the field of view.
The solution uses the advanced camera technology to take a digital picture of a barcode, and executes state-of-the-art software decoding algorithms to extract the data from the image.
RS507/RS507X Hands-Free Imager
The RS507/RS507X Hands-free Imager is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 47
RS507/RS507X Hands-Free Imager
Refer to the RS507/RS507X Hands-free Imager Product Reference Guide for more information.
RS6000 Bluetooth Ring Scanner
The RS6000 Bluetooth Ring Scanner is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 48
RS6000 Bluetooth Ring Scanner
Refer to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
75
Data Capture
DS3678 Digital Scanner
The cordless DS3678 combines superior 1D and 2D omnidirectional barcode scanning performance and advanced ergonomics in a lightweight design. See the DS36X8 Product Reference Guide for more information.
Figure 49
DS3678 Digital Scanner
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode, with a few quick trial efforts to master it.
However, consider the following to optimize scanning performance:
•
Range:
Scanners decode best over a particular working range — minimum and maximum distances from the barcode. This range varies according to barcode density and scanning device optics. Scan within range for quick and constant decodes; scanning too close or too far away prevents decodes. Move the scanner closer and further away to find the right working range for the barcodes being scanned.
•
Angle:
Scanning angle is important for quick decodes. When the illumination/flash reflects directly back into the imager, the specular reflection can blind/saturate the imager. To avoid this, scan the barcode so that the beam does not bounce directly back. Do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
• Hold the device farther away for larger symbols.
• Move the device closer for symbols with bars that are close together.
NOTE
:
Scanning procedures depend on the app and device configuration. An app may use different scanning procedures from the one listed above.
Scanning with Internal Imager
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows the user to enable the imager, decode the barcode data, and display the barcode content.
To scan with the internal imager:
1. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
76
Data Capture
2. Point the exit window on the top of the device at a barcode.
Figure 50
Imager Scanning
3. Press and hold the scan button.
The red laser aiming pattern turns on to assist in aiming.
NOTE
:
When the device is in Picklist mode, the imager does not decode the barcode until the crosshair or aiming dot touches the barcode.
4. Ensure the barcode is within the area formed by the crosshairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 51
Aiming Pattern
Figure 52
Pick List Mode with Multiple Barcodes
5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully.
77
Data Capture
6. Release the scan button.
The barcode content data displays in the text field.
NOTE
:
Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (im age) of a poor or difficult barcode as long as the scan button remains pressed.
-
Scanning with Integrated Camera
To capture bar code data:
NOTE
:
When capturing bar code data in poor lighting, turn on Illumination mode in the DataWedge app. See the device
Integrator Guide for detailed information on configuring DataWedge.
1. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
For example, open the web browser and touch the text field.
2. Aim the camera at a bar code.
3. Press and hold the Scan button. By default, a preview window appears on the screen. The Decode light emitting diode (LED) lights red to indicate that data capture is in process.
Figure 53
App with Preview Window
NOTE
:
When Picklist mode is enabled, move the device until the bar code is centered under the red target on the screen.
4. Move the device until the bar code is visible on the screen.
5. The Decode LED lights green, a beep sounds and the device vibrates, by default, to indicate the bar code was decoded successfully.
6. The captured data appears in the text field.
Scanning with RS507/RS507X Hands-Free Imager
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS507/RS507X:
78
Data Capture
1. Pair the RS507/RS507X with the device. See Pairing Using Simple Serial InterfacePairing Bluetooth
Scanners or Pairing Using Bluetooth Human Interface Device for more information.
2. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3. Point the RS507/RS507X at a barcode.
Figure 54
Barcode Scanning with RS507/RS507X
4. Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS507/RS507X LEDs light green and a beep sounds to indicate the barcode was decoded
79
Data Capture successfully. When the RS507/RS507X is in Pick List mode, the RS507/RS507X does not decode the barcode until the center of the crosshair touches the barcode.
Figure 55
RS507/RS507X Aiming Pattern
Figure 56
RS507/RS507X Pick List Mode with Multiple Barcodes in Aiming Pattern
5. The captured data appears in the text field.
Scanning with RS6000 Bluetooth Ring Scanner
To read a barcode, a scan-enabled app is required. Devices that contain the Zebra DataWedge app allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS6000:
1. Pair the RS6000 with the device. See Pairing Using Bluetooth Human Interface Device for more information.
2. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
80
Data Capture
3. Point the RS6000 at a barcode.
Figure 57
Barcode Scanning with RS6000
4. Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS6000 LEDs light green and a beep sounds to indicate the barcode was decoded successfully. When the RS6000 is in Pick List mode, the RS6000 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 58 RS6000 Aiming Pattern
Figure 59
RS6000 Pick List Mode with Multiple Barcodes in Aiming Pattern
5. The captured data appears in the text field.
81
Data Capture
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner
To scan with the DS3608 or DS3678:
1. Pair the scanner with the device. For more information, see Connecting a USB Scanner for the DS3608 or
Pairing Bluetooth Scanners for the DS3678.
2. Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
3. Point the scanner at a barcode.
Figure 60
Barcode Scanning (DS3678 shown)
4. Press and hold the trigger.
Ensure the barcode is within the area formed by the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 61
DS3608/DS3678 Aiming Pattern
Figure 62
DS3608/DS3678 Pick List Mode with Multiple Barcodes in Aiming Pattern
5. The captured data appears in the text field.
82
Data Capture
Pairing the RS507/RS507X/RS6000 Hands-Free Imager
To connect the RS507/RS507X or RS6000 imager to the device, use one of the following methods:
• Near Field Communication (NFC) (RS6000 only)
• Simple Serial Interface (SSI)
• Bluetooth Human Interface Device (HID) Mode.
Pairing Using Near Field Communication
The device provides the ability to pair the RS6000 using NFC.
NOTE
:
RS6000 Only.
To pair using NFC:
1. Ensure that the RS6000 is in SSI mode. Refer to the RS6000 User Guide for more information.
2. Ensure that NFC is enabled on the device.
3. Align the NFC icon on the RS6000 with the NFC antenna on the device.
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the device. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
Figure 63
Align NFC Antennas
NFC Logo
NFC Antenna Area
Pairing in HID Mode Using Near Field Communication
The device provides the ability to pair the RS6000 in HID mode using NFC.
NOTE
:
RS6000 Only.
To pair in HID mode using NFC:
1. Ensure that NFC is enabled on the device.
2. Ensure that Bluetooth is enabled on the device.
83
Data Capture
3. Place the RS6000 in Human Interface Device (HID) mode. If the RS6000 is already in HID mode, skip to step 4.
a. Remove the battery from the RS6000.
b. Press and hold the Restore key.
c. Install the battery onto the RS6000.
d. Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
e. Scan the barcode below to place the RS6000 in HID mode.
Figure 64
RS6000 Bluetooth HID Barcode
4. Remove the battery from the RS6000.
5. Re-install the battery into the RS6000.
6. Align the NFC icon on the RS6000 with the NFC antenna on the device.
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the device. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on Notification panel and the icon appears in the Status bar.
Figure 65
Align NFC Antennas
NFC Logo
NFC Antenna Area
Pairing Using Simple Serial Interface (SSI)
To pair the RS507/RS507X or RS6000 with the device using SSI.
84
Data Capture
1. Swipe up from the bottom of the Home screen and touch .
Figure 66
Bluetooth Pairing Utility
2. Using the RS507/RS507X or RS6000, scan the barcode on the screen.
The RS507/RS507X or RS6000 emits a string of high/low/high/low beeps. The Scan LED flashes green indicating that the RS507/RS507X or RS6000 is attempting to establish connection with the device. When connection is established, the Scan LED turns off and the RS507/RS507X or RS6000 emits one string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
Pairing Using Bluetooth Human Interface Device
To pair the RS507/RS507X or RS6000 with the device using Human Interface Device (HID):
1. Ensure that Bluetooth is enabled on both devices.
2. Ensure that the Bluetooth device to discover is in discoverable mode.
3. Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4. Place the RS507/RS507X or RS6000 in HID mode. If the RS507/RS507X or RS6000 is already in HID mode, skip to step 5.
a. Remove the battery from the RS507/RS507X or RS6000.
b. Press and hold the Restore key.
c. Install the battery onto the RS507/RS507X or RS6000.
d. Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
85
Data Capture e. Scan the barcode below to place the RS507/RS507X or RS6000 in HID mode.
Figure 67
RS507 Bluetooth HID Barcode
Figure 68
RS6000 Bluetooth HID Barcode
5. Remove the battery from the RS507/RS507X or RS6000.
6. Re-install the battery into the RS507/RS507X or RS6000.
7. Swipe down from the Status bar to open the Quick Access panel and then touch .
8. Touch
Bluetooth
.
9. Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
10.Scroll through the list and select RS507/RS507X or RS6000.
The device connects to the RS507/RS507X or RS6000 and
Connected
appears below the device name.
The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
A notification appears on Notification panel and the icon appears in the Status bar.
Pairing a Bluetooth Scanner
Connect the scanner to the device using one of the following methods:
• Simple Serial Interface (SSI) mode
• Bluetooth Human Interface Device (HID) mode.
Pairing Using Bluetooth Human Interface Device
To pair the scanner with the device using HID:
1. Remove the battery from the scanner.
2. Replace the battery.
3. After the scanner reboots, scan the barcode below to place the scanner in HID mode.
Figure 69
Bluetooth HID Classic Barcode
86
Data Capture
4. On the device, swipe down from the Status bar to open the Quick Access panel and then touch .
5. Touch
Bluetooth
.
6. Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
7. Scroll through the list and select XXXXX xxxxxx, where XXXXX is the scanner and xxxxxx is the serial number.
The device connects to the scanner, the scanner beeps once and
Connected
appears below the device name. The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
87
Data Capture
DataWedge
DataWedge is a utility that adds advanced barcode scanning capability to any application without writing code.
It runs in the background and handles the interface to built-in barcode scanners. The captured barcode data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
To configure DataWedge refer to techdocs.zebra.com/datawedge/ .
Enabling DataWedge
1. Swipe up from the bottom of the Home screen and touch .
2. Touch >
Settings
.
3. Touch the
DataWedge enabled
checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
4. Touch .
Disabling DataWedge
1. Swipe up from the bottom of the Home screen and touch .
2. Touch >
Settings
.
3. Touch the
DataWedge enabled
checkbox. A blue checkmark disappears from the checkbox indicating that
DataWedge is disabled.
4. Touch .
Supported Decoders
NOTE
:
DataWedge supports the decoders listed below but not all are validated on this device.
Table 13 Supported Decoders
Decoders
Australian
Postal
Aztec
Canadian
Postal
O
X
O
O
X
--
O
X
O
O
X
--
88
Data Capture
Table 13 Supported Decoders (Continued)
Decoders
O
O
--
O
X
--
--
--
O
X
X
O
X
X
X
O
O
O
O
O
X
X
O
X
O
O
Chinese 2 of 5 O
Codabar
Code 11
X
O
Code 128
Code 39
Code 93 O
Composite AB O
X
X
Composite C O
Discrete 2 of 5 O
Datamatrix
Dutch Postal
X
O
DotCode
EAN13
EAN8
GS1 DataBar
GS1 DataBar
Expanded
GS1 DataBar
Limited
HAN XIN
Interleaved 2 of 5
O
GS1
Datamatrix
O
GS1 QRCode O
O
O
X
X
X
X
X
Japanese
Postal
O
Korean 3 of 5 O
MAIL MARK
Matrix 2 of 5
Maxicode
X
O
X
O
O
X
O
X
O
O
O
O
X
X
O
X
X
X
O
O
O
O
O
X
X
O
X
O
O
O
O
X
O
X
O
O
O
O
X
X
O
X
X
X
O
O
O
O
O
X
X
O
X
O
O
89
Data Capture
Table 13 Supported Decoders (Continued)
Decoders
MicroPDF
MicroQR
MSI
PDF417
QR Code
Decoder
Signature
TLC 39
Trioptic 39
UK Postal
UPCA
UPCE0
UPCE1
US4state
US4state FICS O
US Planet O
US Postnet O
O
O
X
X
O
O
O
X
X
O
O
O
O
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
O
X
X
O
Touch to return to the previous screen.
O
O
X
X
O
O
O
O
O
O
X
X
--
O
O
O
O
O
X
X
O
O
O
O
O
O
90
Wireless
This section provides information on the wireless features:
• Wireless Local Area Network (WLAN)
• Bluetooth
• Near Field Communications (NFC)
• Cast.
Accessing Settings
Access Settings in any of the following ways:
• Swipe down with two fingers from the top of the Home screen to open the Quick Access panel and touch
.
• Double-swipe down from the top of the Home screen to open the Quick Access panel and touch
.
• Swipe up from the bottom of the Home screen to open APPS and touch
Settings
.
Wireless Local Area Networks
Wireless local area networks (WLANs) allow the device to communicate wirelessly inside a building.
Before using the device on a WLAN, the facility must be set up with the required hardware to run the
WLAN (sometimes known as infrastructure). The infrastructure and the device must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches, Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the
Wireless & networks
settings configure the device to match the security scheme.
The device supports the following WLAN security options:
• Open
• Wireless Equivalent Privacy (WEP)
• Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK)
91
Wireless
• Extensible Authentication Protocol (EAP).
• LEAP
• Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication
• Transport Layer Security (TLS)
• TTLS - with Password Authentication Protocol (PAP), MSCHAP and MSCHAPv2 authentication.
• EAP-FAST - with MSCHAPV2 and GTC authentication.
• PWD
The
Status
bar displays icons that indicate Wi-Fi network availability and Wi-Fi status.
NOTE
:
To extend the life of the battery, turn off Wi-Fi when not in use.
Connecting to a Wi-Fi Network
To connect to a Wi-Fi network:
1. Go to
Settings
.
2. Touch
Wi-Fi
to open the
Wi-Fi
screen. The device searches for WLANs in the area and lists them.
Figure 70
Wi-Fi Screen
-
3. Scroll through the list and select the desired WLAN network.
92
Wireless
4. For open networks, touch profile once or press and hold and then select
Connect to network
or for secure networks enter the required password or other credentials then touch
Connect
. See the system administrator for more information.
The device obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the device with a fixed internet protocol (IP) address, Refer to the device Integrator Guide for more information.
5. In the Wi-Fi setting field,
Connected
appears indicating that the device is connected to the WLAN.
Removing a Wi-Fi Network
To remove a remembered or connected network:
1. Go to
Settings
.
2. Touch
Network & Internet
>
W-Fi
.
3. Scroll down to the bottom of the list and touch
Saved networks
.
4. Touch the name of the network.
5. In the dialog box, touch
FORGET
.
6. Touch .
WLAN Configuration
This section provides information on configuring Wi-Fi settings.
Configuring a Secure Wi-Fi Network
To set up a Wi-Fi network:
1. Go to
Settings
.
2. Touch
Network & Internet
>
Wi-Fi
.
3. Slide the switch to the
ON
position.
4. The device searches for WLANs in the area and lists them on the screen.
5. Scroll through the list and select the desired WLAN network.
6. Touch the desired network. If the network security is
Open
, the device automatically connects to the network. For all other network security a dialog box appears.
7. If the network security is
WEP
or
WPA/WPS2 PSK
, enter the required password and then touch
Connect
.
93
Wireless
8. If the network security is 802.1x EAP:
• Touch the
EAP method
drop-down list and select
PEAP
,
TLS
,
TTLS,
or
LEAP
.
• Touch the
Phase 2 authentication
drop-down list and select an authentication method.
• If required, touch
CA certificate
and select a Certification Authority (CA) certificate. Note: Certificates are installed using the
Security
settings.
• If required, touch
User certificate
and select a user certificate. Note: User certificates are installed using the Location & security settings.
• If required, in the
Identity
text box, enter the username credentials.
• If desired, in the
Anonymous identity
text box, enter an anonymous identity username.
• If required, in the
Password
text box, enter the password for then given identity.
NOTE
:
By default, the network Proxy is set to use a static IP address.
None
and the IP settings is set to
DHCP
. See Configuring for a Proxy Server for setting connection to a proxy server and see Configuring the Device to Use a Static IP Address for setting the device to
9. Touch
Connect
.
10.Touch .
Manually Adding a Wi-Fi Network
Manually add a Wi-Fi network if the network does not broadcast its name (SSID) or to add a Wi-Fi network when out of range.
1. Go to
Settings
.
2. Touch
Network & Internet
>
Wi-Fi
.
3. Slide the Wi-Fi switch to the
On
position.
4. Scroll to the bottom of the list and select
Add network
.
5. In the
Network name
text box, enter the name of the Wi-Fi network.
6. In the
Security
drop-down list, set the type of security to:
• None
• WEP
• WPA/WPA2 PSK
•
802.1x EAP
.
7. If the network security is
None
, touch
Save
.
8. If the network security is
WEP
or
WPA/WPA2 PSK
, enter the required password and then touch
Save
.
94
Wireless
9. If the network security is
802.1x EAP
:
• Touch the
EAP method
drop-down list and select
PEAP
,
TLS
,
TTLS,
or
LEAP
.
• Touch the
Phase 2 authentication
drop-down list and select an authentication method.
• If required, touch
CA certificate
and select a Certification Authority (CA) certificate. Note: Certificates are installed using the
Security
settings.
• If required, touch
User certificate
and select a user certificate. Note: User certificates are installed using the
Security
settings.
• If required, in the
Identity
text box, enter the username credentials.
• If desired, in the
Anonymous
identity text box, enter an anonymous identity username.
• If required, in the
Password
text box, enter the password for the given identity.
NOTE
:
By default, the network Proxy is set to use a static IP address.
None
and the IP settings is set to
DHCP
. See Configuring for a Proxy Server for setting connection to a proxy server and see Configuring the Device to Use a Static IP Address for setting the device to
10.Touch
Save
. To connect to the saved network, touch and hold on the saved network and select
Connect to network
.
11.Touch .
Configuring for a Proxy Server
A proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers. A client connects to the proxy server and requests some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server evaluates the request according to its filtering rules. For example, it may filter traffic by IP address or protocol. If the request is validated by the filter, the proxy provides the resource by connecting to the relevant server and requesting the service on behalf of the client.
It is important for enterprise customers to be able to set up secure computing environments within their companies, making proxy configuration essential. Proxy configuration acts as a security barrier ensuring that the proxy server monitors all traffic between the Internet and the intranet. This is normally an integral part of security enforcement in corporate firewalls within intranets.
To configure the device for a proxy server:
1. Go to
Settings
.
2. Touch
Network & Internet
>
Wi-Fi
.
3. Slide the Wi-Fi switch to the
On
position.
4. In the network dialog box, select and touch a network.
5. Touch
Advanced options
.
6. Touch
Proxy
and select
Manual
.
7. In the
Proxy hostname
text box, enter the address of the proxy server.
8. In the
Proxy port
text box, enter the port number for the proxy server.
9. In the
Bypass proxy for
text box, enter addresses for web sites that are not required to go through the proxy server. Use a comma “,” between addresses. Do not use spaces or carriage returns between addresses.
95
Wireless
10.Touch
Connect
.
11.Touch .
Configuring the Device to Use a Static IP Address
By default, the device is configured to use Dynamic Host Configuration Protocol (DHCP) to assign an Internet protocol (IP) address when connecting to a wireless network.
To configure the device to connect to a network using a static IP address:
1. Go to
Settings
.
2. Touch
Network & Internet
>
Wi-Fi
.
3. Slide the Wi-Fi switch to the
On
position.
4. In the network dialog box, select and touch a network.
5. Touch
Advanced options
.
6. Touch
IP settings
and select
Static
.
7. In the
IP address
text box, enter an IP address for the device.
8. If required, in the
Gateway
text box, enter a gateway address for the device.
9. If required, in the
Network prefix length
text box, enter the prefix length.
10.If required, in the
DNS 1
text box, enter a Domain Name System (DNS) address.
11.If required, in the
DNS 2
text box, enter a DNS address.
12.Touch
Connect
.
13.Touch .
Wi-Fi Preferences
Use the
Wi-Fi preferences
to configure advanced Wi-Fi settings. From the Wi-Fi screen scroll down to the bottom of the screen and touch
Wi-Fi preferences
.
• Turn on W-Fi automatically
- When enabled, Wi-Fi automatically turns back on when near high quality saved networks.
•
Open network notification
- When enabled, notifies the user when an open network is available.
• Advanced - Touch to expand options.
•
Additional settings
- See Additional Settings.
•
Install Certificates
– Touch to install certificates.
•
Network rating provider
- Disabled (AOSP devices). To help determine what constitutes a good Wi-Fi network, Android supports external Network rating providers that provide information about the quality of open Wi-Fi networks. Select one of the providers listed or
None
. If none are available or selected, the
Connect to open networks feature is disabled.
•
Wi-Fi Direct
- Displays a list of devices available for a direct Wi-Fi connection.
•
MAC address
- Displays the Media Access Control (MAC) address of the device when connecting to
Wi-Fi networks.
•
IP address
- Displays the IP address of the device when connecting to Wi-Fi networks.
96
Wireless
Additional Wi-Fi Settings
NOTE
:
Additional Wi-Fi settings are for the device, not for a specific wireless network.
Use the
Additional Settings
to configure additional Wi-Fi settings. To view the additional Wi-Fi settings, scroll to the bottom of the
Wi-Fi
screen and touch
Wi-Fi Preferences
>
Advanced
>
Additional settings.
• Regulatory
•
Country Selection
- Displays the acquired country code if 802.11d is enabled, else it displays the currently selected country code.
•
Region code
- Displays the current region code.
• Band and Channel Selection
•
Wi-Fi frequency band
- Set the frequency band to:
Auto
(default),
5 GHz only
or
2.4 GHz only
.
•
Available channels (2.4 GHz)
- Touch to display the
Available channels
menu. Select specific channels and touch
OK
.
•
Available channels (5 GHz)
- Touch to display the
Available channels
menu. Select specific channels and touch
OK
.
• Logging
•
Advanced Logging
– Touch to enable advanced logging or change the log directory.
•
Wireless logs
- Use to capture Wi-Fi log files.
•
Fusion Logger
- Touch to open the
Fusion Logger
application. This application maintains a history of high level WLAN events which helps to understand the status of connectivity.
•
Fusion Status
- Touch to display live status of WLAN state. Also provides information about the device and connected profile.
• About
•
Version
- Displays the current Fusion information.
Wi-Fi Direct
Wi-Fi Direct devices can connect to each other without having to go through an access point. Wi-Fi Direct devices establish their own ad-hoc network when required, letting you see which devices are available and choose which one you want to connect to.
1. Go to
Settings
.
2. Touch
Wi-Fi
>
Wi-Fi preferences
>
Advanced
>
Wi-Fi Direct
. The device begins searching for another
Wi-Fi Direct device.
3. Under
Peer devices
, touch the other device name.
4. On the other device, select
Accept
.
5.
Connected
appears on the device. On both devices, in their respective Wi-Fi Direct screens, the other device name appears in the list.
Bluetooth
Bluetooth devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band
97
Wireless
(802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 m (32.8 ft)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (for example, files, appointments, and tasks) with other Bluetooth enabled devices such as printers, access points, and other mobile devices.
The device supports Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with
Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work.
There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
• Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels.
AFH coexistence allows enterprise devices to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 m (32.8 ft). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether in open space or closed office space.
NOTE
:
It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified.
This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event).
Authentication of Bluetooth devices is based-upon a challenge-response transaction. Bluetooth allows for a
PIN or passkey used to create other 128-bit keys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
• Perform pairing in a secure environment
98
Wireless
• Keep PIN codes private and do not store the PIN codes in the device
• Implement application-level security.
Bluetooth Profiles
The device supports the Bluetooth services listed in the table below:
Table 14
Bluetooth Profiles
Profile
Service Discovery Protocol
(SDP)
Serial Port Profile (SPP)
Object Push Profile (OPP)
Advanced Audio Distribution
Profile (A2DP)
Audio/Video Remote Control
Profile (AVRCP)
Personal Area Network (PAN)
Human Interface Device Profile
(HID)
Headset Profile (HSP)
Hands-Free Profile (HFP)
Phone Book Access Profile
(PBAP)
Out of Band (OOB)
Symbol Serial Interface (SSI)
Description
Handles the search for known and specific services as well as general services.
Allows use of RFCOMM protocol to emulate serial cable connection between two Bluetooth peer devices. For example, connecting the device to a printer.
Allows the device to push and pull objects to and from a push server.
Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
Allows the device to control A/V equipment to which a user has access.
It may be used in concert with A2DP.
Allows the use of Bluetooth Network Encapsulation Protocol to provide
L3 networking capabilities over a Bluetooth link. Only PANU role is supported.
Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
Allows car hands-free kits to communicate with the device in the car.
Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so you can initiate a call from the car display.
Allows exchange of information used in the pairing process. Pairing is completed using the Bluetooth radio, but requires information from the
OOB mechanism. Using OOB with NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
Allows for communication with Bluetooth Imager.
Bluetooth Power States
The Bluetooth radio is off by default:
• Suspend - When the device goes into suspend mode, the Bluetooth radio stays on.
• Airplane Mode - When the device is placed in Airplane Mode, the Bluetooth radio turns off. When Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the Bluetooth radio can be turned back on if desired.
99
Wireless
Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (for example, an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the
Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with
Bluetooth radios in close proximity.
NOTE
:
To achieve the best battery life, turn off radios when not in use.
Enabling Bluetooth
To enable Bluetooth:
1. Go to
Settings
.
2. Touch to turn Bluetooth on.
3. Touch .
Disabling Bluetooth
To disable Bluetooth:
1. Go to
Settings
.
2. Touch to turn Bluetooth off.
3. Touch .
Discovering Bluetooth Device(s)
The device can receive information from discovered devices without pairing. However, once paired, the device and a paired device exchange information automatically when the Bluetooth radio is on. To find Bluetooth devices in the area:
1. Ensure that Bluetooth is enabled on both devices.
2. Ensure that the Bluetooth device to discover is in discoverable mode.
3. Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4. Swipe down from the Status bar to open the Quick Access panel.
5. Touch and hold
Bluetooth
.
6. Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
7. Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
8. Touch
Pair
on both devices.
9. The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
100
Wireless
Changing the Bluetooth Name
By default, the device has a generic Bluetooth name that is visible to other devices when connected.
1. Go to
Settings
.
2. Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3. If Bluetooth is not on, move the switch to turn Bluetooth on.
4. Touch
Device name
.
5. Enter a name and touch
RENAME
.
6. Touch .
Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device.
1. Go to
Settings
.
2. Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3. In the list, touch the unconnected Bluetooth device.
When connected,
Connected
appears below the device name.
Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles. To select a profile:
1. Go to
Settings
.
2. Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3. In the
Paired Devices
list, touch next to the device name.
4. Turn on or off a profile to allow the device to use that profile.
5. Touch .
Unpairing a Bluetooth Device
To unpair a Bluetooth device and erase all pairing information:
1. Go to
Settings
.
2. Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3. In the
Paired Devices
list, touch next to the device name.
4. Touch
FORGET
.
5. Touch .
101
Wireless
Near Field Communications
NFC/HF RFID is a short-range wireless connectivity technology standard that enables secure transaction between a reader and a contactless smartcard. The technology is based on ISO/IEC 14443 type A and B
(proximity) and ISO/IEC 15693 (vicinity)standards, using the HF 13.56 MHz unlicensed band. The device supports the following operating modes:
• Reader mode
• Peer-to-Peer communication
• Card Emulation mode.
Using NFC, the device can:
• Read contactless cards such as contactless tickets, ID cards and ePassport.
• Read and write information to contactless cards such as SmartPosters and tickets, as well as devices with
NFC interface such as vending machines.
• Read information from supported medical sensors.
• Pair with supported Bluetooth devices such as printers , ring scanners (ex. RS6000), and headsets (ex.
HS3100).
• Exchange data with another NFC device.
• Emulate contactless card such as payment, ticket, or SmartPoster.
The device NFC antenna is positioned to read NFC cards from the top of the device while the device is being held.
The device NFC antenna is located on the back of the device, near the Interface Connector.
Reading NFC Cards
To read NFC cards:
1. Launch an NFC enabled application.
2. Hold device as shown.
3. Move the device close to the NFC card until it detects the card.
4. Hold the card steadily until the transaction is complete (usually indicated by the application).
Figure 71
Reading Cards
102
Wireless
Sharing Information Using NFC
You can beam content like a web page, contact cards, pictures, YouTube links or location information from your screen to another device by bringing the devices together back to back.
Make sure both devices are unlocked, support NFC, and have both NFC and Android Beam turned on.
1. Open a screen that contains a web page, video, photo or contact.
2. Move the back of the device toward the back of the other device.
Figure 72
Sharing Data Using NFC
When the devices connect, a sound emits, the image on the screen reduces in size, the message
Touch to beam
displays.
3. Touch anywhere on the screen.
The transfer begins.
103
Wireless
Cast
Use
Cast
to mirror the device screen on a Miracast enabled wireless display.
1. Go to
Settings
.
2. Touch
Connected devices
>
Connection preferences
>
Cast
.
3. Touch >
Enable wireless display
. The device searches for nearby Miracast devices and lists them.
4. Touch a device to begin casting.
5. Touch .
104
Accessories
This table lists the accessories available for the device.
Table 15
Accessories
Accessory
Cradles
2-Slot Charge Only
Cradle
2-Slot USB/Ethernet
Cradle
Part Number
CRD-TC7X-SE2CPP-01
CRD-TC7X-SE2EPP-01
5-Slot Charge Only
Cradle
5-Slot Ethernet Cradle
Cradle Mount
CRD-TC7X-SE5C1-01
CRD-TC7X-SE5EU1–01
BRKT-SCRD-SMRK-01
Description
Provides device and spare battery charging. Use with power supply, p/n
PWR-BGA12V50W0WW.
Provides device and spare battery charging and USB communication with a host computer and Ethernet communication with a network. Use with power supply, p/n
PWR-BGA12V50W0WW.
Charges up to five devices. Use with power supply, p/n PWR-BGA12V108W0WW and
DC line cord, p/n CBL-DC-381A1-01. Can accommodate one 4-Slot Battery Charger using the Battery Adapter Cup.
Provides device charging and provides
Ethernet communication for up to five devices. Use with power supply, p/n
PWR-BGA12V108W0WW and DC line cord, p/n CBL-DC-381A1-01. Can accommodate one 4-Slot Battery Charger using the Battery Adapter Cup.
Mounts the 5-Slot Charge Only Cradle,
5-Slot Ethernet Cradle, and 4-Slot Battery
Charger to a wall or rack.
Batteries and Chargers
4,620 mAh
PowerPrecision+ battery
4-Slot Spare Battery
Charger
BTRY-TC7X-46MPP-01
BTRY-TC7X-46MPP-10
SAC-TC7X-4BTYPP-01
Replacement battery (single pack).
Replacement battery (10–pack).
Charges up to four battery packs. Use with power supply, p/n
PWR-BGA12V50W0WW.
105
Accessories
Table 15
Accessories (Continued)
Accessory
Battery Charger Adapter
Cup
Part Number
CUP-SE-BTYADP1-01
Description
Allows for one 4-Slot Battery Charger to be charged and docked on the left most slot of the 5-Slot cradles (maximum one per cradle).
Vehicle Solutions
Charging Cable Cup
Charge Only Vehicle
Cradle
TC7X Data
Communication Enabled
Vehicle Cradle with Hub
Kit
Cigarette Light Adapter
Auto Charge Cable
Hard-wire Auto Charge
Cable
RAM Mount
CRD-TC7X-VCD1-01
CHG-AUTO-CLA1-01
CHG-AUTO-HWIRE1-01
RAM-B-166U
RAM Mount Base
CHG-TC7X-CLA1-01
CRD-TC7X-CVCD1-01
RAM-B-238U
Charge and Communication Cables
Charging Cable Cup CHG-TC7X-CBL1-01
Provides power to the device from a cigarette lighter socket.
Charges and securely holds the device.
Requires power cable
CHG-AUTO-CLA1-01 or
CHG-AUTO-HWIRE1-01, sold separately.
Contains the TC7X Vehicle
Communication Charging Cradle and the
USB I/O Hub.
Provides power to the Vehicle Cradle from a cigarette lighter socket.
Provides power to the Vehicle Cradle from the vehicle's power panel.
Provides window mounting option for the
Vehicle Cradle. RAM Twist Lock Suction
Cup with Double Socket Arm and Diamond
Base Adapter. Overall Length: 6.75”.
RAM 2.43" x 1.31" Diamond Ball base with
1" ball.
Snap-On USB Cable
MSR Adapter
Snap-On DEX Cable
Audio Accessories
Rugged Headset
CBL-TC7X-USB1-01
MSR-TC7X-SNP1-01
CBL-TC7X-DEX1-01
HS2100-OTH
Provides power to the device. Use with power supply, p/n PWR-BUA5V16W0WW, sold separately.
Provides power to the device and USB communication with a host computer. Use with power supply, p/n
PWR-BUA5V16W0WW, sold separately.
Provides power and USB communication with a host computer. Use with USB-C cable, sold separately.
Provides electronic data exchange with devices such as vending machines.
Bluetooth Headset HS3100-OTH
Rugged wired headset. Includes HS2100
Boom Module and HSX100 OTH
Headband Module.
Rugged Bluetooth Headset. Includes
HS3100 Boom Module and HSX100 OTH
Headband Module.
106
Accessories
Table 15
Accessories (Continued)
Accessory
3.5 mm Audio Adapter
Part Number
ADP-TC7X-AUD35-01
3.5 mm Headset
3.5 mm Quick
Disconnect Adapter
Cable
Scanning
Trigger Handle
HDST-35MM-PTVP-01
ADP-35M-QDCBL1-01
TRG-TC7X-SNP1-02
Snaps onto the device and provides audio to a wired headset with 3.5 mm plug.
Use for PTT and VoIP calls.
Provides connection to the 3.5 mm
Headset.
Description
Trigger Handle Attach
Plate with Tether
Trigger Handle Attach
Plate
ADP-TC7X-CLHTH-10
ADP-TC7X-CLPTH1-20
Adds gun-style handle with a scanner trigger for comfortable and productive scanning.
Trigger Handle Attach Plate with tether.
Allows for installation of the Trigger Handle
(10-pack). Use with charge only cradles.
Trigger Handle Attach Plate. Allows for installation of the Trigger Handle
(20-pack). Use with Ethernet and charge only cradles.
Carrying Solutions
Soft Holster
Rigid Holster
Hand Strap
SG-TC7X-HLSTR1-02
SG-TC7X-RHLSTR1-01
SG-TC7X-HSTRP2-03
Stylus and Coiled Tether SG-TC7X-STYLUS-03
Screen Protector SG-TC7X-SCRNTMP-01
Power Supplies
Power Supply PWR-BUA5V16W0WW
Power Supply
TC7X soft holster.
TC7X rigid holster.
Replacement hand strap with hand strap mounting clip (3–pack).
TC7X stylus with coiled tether (3-pack).
Provides additional protection for the screen (1-pack).
PWR-BGA12V50W0WW
Provides power to the device using the
Snap-On USB Cable, Snap-on Serial
Cable or Charging Cable Cup. Requires
DC Line Cord, p/n DC-383A1-01 and country specific three wire grounded AC line cord sold separately.
Provides power to the 2–Slot cradles and
4-Slot Spare Battery Charger. Requires
DC Line Cord, p/n CBL-DC-388A1-01 and country specific three wire grounded AC line cord sold separately.
107
Accessories
Table 15
Accessories (Continued)
Accessory
Power Supply
DC Line Cord
DC Line Cord
Part Number
PWR-BGA12V108W0WW Provides power to the 5-Slot Charge Only cradle and the 5-Slot Ethernet Cradle.
Requires DC Line Cord, p/n
CBL-DC-381A1-01 and country specific three wire grounded AC line cord sold separately.
CBL-DC-388A1-01
CBL-DC-381A1-01
Description
Provides power from the power supply to the 2-Slot cradles and 4-Slot Spare Battery
Charger.
Provides power from the power supply to the 5-Slot Charge Only Cradle and 5-Slot
Ethernet Cradle.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 16
Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Fast Blinking Amber
Slow Blinking Red
Solid Red
Fast Blinking Red
Off
Indication
Spare battery is charging.
Charging complete.
Error in charging; check placement of spare battery.
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F))
108
Accessories the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
2-Slot Charge Only Cradle
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
The 2-Slot Charge Only Cradle:
• Provides 5 VDC power for operating the device.
• Charges the device’s battery.
• Charges a spare battery.
Figure 73
2–Slot Charge Only Cradle
Spare Battery
Charging LED
Power LED
109
Setup
Figure 74
2–Slot Charge Only Cradle
Accessories
110
Accessories
Charging the Device
1. Insert the device into the slot to begin charging.
Figure 75
Battery Charging
2. Ensure the device is seated properly.
111
Accessories
Charging the Spare Battery
1. Insert the battery into the right slot to begin charging.
Figure 76
Spare Battery Charging
2. Ensure the battery is seated properly.
112
Accessories
2-Slot USB/Ethernet Cradle
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
The 2-Slot USB/Ethernet Cradle:
• Provides 5.0 VDC power for operating the device.
• Charges the device’s battery.
• Charges a spare battery.
• Connects the device to an Ethernet network.
• Provides communication to a host computer using a USB cable.
NOTE
:
Remove all attachments on the device, except the hand strap, before place onto the cradle.
Figure 77
2-Slot USB/Ethernet Cradle
Spare Battery
Charging LED
Power LED
113
Setup
Figure 78
2–Slot USB/Ethernet Cradle
Accessories
114
Accessories
Charging the Device
1. Place the bottom of the device into the base.
Figure 79
Battery Charging
2. Rotate the top of the device until the connector on the back of the device mates with the connector on the cradle.
3. Ensure the device is connected properly. The charging Charging/Notification LED on the device begins blinking amber indicating that the device is charging.
115
Accessories
Charging the Spare Battery
1. Insert the battery into the right slot to begin charging.
Figure 80
Spare Battery Charging
2. Ensure the battery is seated properly.
USB/Ethernet Communication
The 2–Slot USB/Ethernet Cradle provides both Ethernet communication with a network and USB communication with a host computer. Prior to using the cradle for Ethernet or USB communication. Ensure that the switch on the USB/Ethernet module is set properly.
Turn the cradle over to view the module.
Figure 81
2–Slot USB/Ethernet Cradle Module Switch
For Ethernet communication, slide the switch to the position.
For USB communication, slide the switch to the position.
Place the switch in the center position to disable communications.
116
Accessories
Ethernet LED Indicators
There are two LEDs on the USB/Ethernet Module RJ-45 connector. The green LED lights to indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link.
Figure 82
LED Indicators
Yellow LED Green LED
Table 17
USB/Ethernet Module LED Data Rate Indicators
Data Rate Yellow LED
100 Mbps
10 Mbps
On/Blink
On/Blink
On
Off
Green LED
Establishing Ethernet Connection
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch
Ethernet
.
3. Slide the Ethernet switch to the
ON
position.
4. Insert the device into a slot.
The icon appears in the Status bar.
5. Touch
Eth0
to view Ethernet connection details.
Ethernet Settings
The following settings can be configured when using Ethernet communication:
• Proxy Settings
• Static IP.
Configuring Ethernet Proxy Settings
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch
Network & Internet
.
3. Touch
Ethernet
.
4. Place the device into the Ethernet cradle slot.
5. Slide the switch to the
ON
position.
117
Accessories
6. Touch and hold
Eth0
until the menu appears.
7. Touch
Modify Proxy
.
8. Touch the
Proxy
drop-down list and select
Manual
.
9. In the
Proxy hostname
field, enter the proxy server address.
10.In the
Proxy port
field, enter the proxy server port number.
NOTE
:
dresses.
When entering proxy addresses in the Bypass proxy for field, do not use spaces or carriage returns between ad
-
11.In the
Bypass proxy for
text box, enter addresses for web sites that do not require to go through the proxy server. Use the separator “|” between addresses.
12.Touch
MODIFY
.
13.Touch .
Configuring Ethernet Static IP Address
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch
Network & Internet
.
3. Touch
Ethernet
.
4. Place the device into the Ethernet cradle slot.
5. Slide the switch to the
ON
position.
6. Touch
Eth0
.
7. Touch
Disconnect
.
8. Touch
Eth0
.
9. Touch and hold the IP settings drop-down list and select
Static
.
10.In the
IP
address field, enter the proxy server address.
11.If required, in the
Gateway
field, enter a gateway address for the device.
12.If required, in the
Netmask
field, enter the network mask address
13.If required, in the
DNS address
fields, enter a Domain Name System (DNS) addresses.
14.Touch
CONNECT
.
15.Touch .
118
Accessories
5-Slot Charge Only Cradle
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
The 5-Slot Charge Only Cradle:
• Provides 5 VDC power for operating the device.
• Simultaneously charges up to five devices and up to four devices and one 4-Slot Battery Charger using the
Battery Charger Adapter. See the device Integrator Guide for Android 8.1 Oreo for information on installing the 4-Slot Battery Charger onto the cradle.
• Consists of a cradle base and cups that can be configured for various charging requirements.
Figure 83
5-Slot Charge Only Cradle
Power LED
Setup
Figure 84
5-Slot Charge Only Cradle
119
Accessories
Charging the Device
1. Insert the device into a slot to begin charging.
Figure 85
Battery Charging
120
Accessories
Figure 86
5-Slot Charge Only Cradle with Four Slot Battery Charger
2. Ensure the device is seated properly.
121
Accessories
Installing the Four Slot Battery Charger
NOTE
:
The Battery Charger must be installed in the first slot only.
1. Remove power from the cradle.
Figure 87
Remove Power from Cradle
2. Using a Phillips screwdriver, remove the screw securing the cup to the cradle base.
Figure 88
Remove Screw
122
3. Slide the cup to the front of the cradle.
Figure 89
Remove Cup
Accessories
4. Carefully lift the cup up to expose the cup power cable.
5. Disconnect the cup power cable.
Figure 90
Disconnect Cup Power Cable
NOTE
:
Place power cable into adapter to avoid pinching cable.
123
Accessories
6. Connect the Battery Adapter power cable to the connector on the cradle.
Figure 91
Connect Adapter Power Cable
7. Place adapter onto cradle base and slide toward rear of cradle.
Figure 92
Install Adapter
124
Accessories
8. Using a Phillips screwdriver, secure adapter to cradle base with screw.
Figure 93
Secure adapter to Cradle
9. Align mounting holes on the bottom of the Four Slot Battery Charger with the stubs on the Battery Adapter.
Figure 94
Install Four Slot Battery Charger
10.Slide the Four Slot battery Charger down toward the front of the cradle.
125
Accessories
11.Connect the output power plug into the power port on the Four Slot Battery Charger.
Figure 95
Connect Output Power Plug
Removing the 4-Slot Battery Charger
1. Disconnect the output power plug from the 4-Slot Battery Charger.
2. At the back of the cup, press down on the release latch.
Figure 96
Press Release Latch
3. Slide the 4-Slot Battery Charger toward the front of the cradle.
4. Lift the 4-Slot off the cradle cup.
126
Accessories
4-Slot Charge Only Cradle with Battery Charger
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
The 4-Slot Charge Only Cradle with Battery Charger:
• Provides 5 VDC power for operating the device.
• Simultaneously charges up to four devices and up to four spare batteries.
Figure 97
4-Slot Charge Only Cradle with Battery Charger
Power LED
127
Accessories
Setup
Figure 98
Connect Battery Charger Output Power Plug
Figure 99
Connect Charge Only Cradle Power
128
Accessories
Charging the Device
1. Insert the device into a slot to begin charging.
Figure 100
Battery Charging
2. Ensure the device is seated properly.
NOTE
:
See the device Integrator Guide for Android 8.1 Oreo for information on installing the 4-Slot Battery Charger onto the cradle.
Charging Spare Batteries
1. Connect the charger to a power source.
129
Accessories
2. Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact.
Figure 101
4-Slot Battery Charger
Battery
Battery
Charge LED
Battery Slot
130
Accessories
5-Slot Ethernet Cradle
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
The 5-Slot Ethernet Cradle:
• Provides 5.0 VDC power for operating the device.
• Connects up to five devices to an Ethernet network.
• Simultaneously charges up to five devices and up to four devices and on 4-Slot Battery Charger using the
Battery Charger Adapter.
Figure 102
5-Slot Ethernet Cradle
1000 LED
100/10 LED
131
Accessories
Setup
Connect the 5-Slot Ethernet cradle to a power source.
Figure 103
5-Slot Ethernet Cradle Setup
Daisy-chaining Ethernet Cradles
Daisy-chain up to ten 5-Slot Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will almost certainly result.
To daisy-chain 5-Slot Ethernet cradles:
1. Connect power to each 5-Slot Ethernet cradle.
2. Connect an Ethernet cable to the one of the ports on the back of the first cradle and to the Ethernet switch.
132
Accessories
3. Connect the other end of the Ethernet cable to one of the ports of the back of the second 5-Slot Ethernet cradle.
Figure 104
Daisy-chaining 5-Slot Ethernet Cradles
To Switch To Power Supply
To Next
Cradle
To Power Supply
4. Connect additional cradles as described in step 2 and 3.
133
Accessories
Charging the Device
1. Insert the device into a slot to begin charging.
Figure 105
Battery Charging
134
Accessories
2. Ensure the device is seated properly.
Figure 106
5-Slot Ethernet Cradle with 4-Slot Battery Charger
135
Accessories
Installing the Four Slot Battery Charger
NOTE
:
The Battery Charger must be installed in the first slot only.
1. Remove power from the cradle.
Figure 107
Remove Power from Cradle
2. Using a Phillips screwdriver, remove the screw securing the cup to the cradle base.
Figure 108
Remove Screw
136
3. Slide the cup to the front of the cradle.
Figure 109
Remove Cup
Accessories
4. Carefully lift the cup up to expose the cup power cable.
5. Disconnect the cup power cable.
Figure 110
Disconnect Cup Power Cable
NOTE
:
Place power cable into adapter to avoid pinching cable.
137
Accessories
6. Connect the Battery Adapter power cable to the connector on the cradle.
Figure 111
Connect Adapter Power Cable
7. Place adapter onto cradle base and slide toward rear of cradle.
Figure 112
Install Adapter
138
Accessories
8. Using a Phillips screwdriver, secure adapter to cradle base with screw.
Figure 113
Secure adapter to Cradle
9. Align mounting holes on the bottom of the Four Slot Battery Charger with the stubs on the Battery Adapter.
Figure 114
Install Four Slot Battery Charger
10.Slide the Four Slot battery Charger down toward the front of the cradle.
139
Accessories
11.Connect the output power plug into the power port on the Four Slot Battery Charger.
Figure 115
Connect Output Power Plug
Removing the 4-Slot Battery Charger
1. Disconnect the output power plug from the 4-Slot Battery Charger.
2. At the back of the cup, press down on the release latch.
Figure 116
Press Release Latch
3. Slide the 4-Slot Battery Charger toward the front of the cradle.
4. Lift the 4-Slot off the cradle cup.
140
Accessories
Ethernet Communication
Ethernet LED Indicators
There are two green LEDs on the side of the cradle. These green LEDs light and blink to indicate the data transfer rate.
Table 18
LED Data Rate Indicators
Data Rate
1 Gbps
100 Mbps
10 Mbps
On/Blink
Off
Off
1000 LED
Off
On/Blink
On/Blink
100/10 LED
Establishing Ethernet Connection
1. Swipe down from the Status bar to open the Quick Access panel and then touch .
2. Touch
Ethernet
.
3. Slide the Ethernet switch to the
ON
position.
4. Insert the device into a slot.
The icon appears in the Status bar.
5. Touch
Eth0
to view Ethernet connection details.
Ethernet Settings
The following settings can be configured when using Ethernet communication:
• Proxy Settings
• Static IP.
Configuring Ethernet Proxy Settings
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch
Network & Internet
.
3. Touch
Ethernet
.
4. Place the device into the Ethernet cradle slot.
5. Slide the switch to the
ON
position.
6. Touch and hold
Eth0
until the menu appears.
7. Touch
Modify Proxy
.
8. Touch the
Proxy
drop-down list and select
Manual
.
9. In the
Proxy hostname
field, enter the proxy server address.
10.In the
Proxy port
field, enter the proxy server port number.
141
Accessories
NOTE
:
dresses.
When entering proxy addresses in the Bypass proxy for field, do not use spaces or carriage returns between ad
-
11.In the
Bypass proxy for
text box, enter addresses for web sites that do not require to go through the proxy server. Use the separator “|” between addresses.
12.Touch
MODIFY
.
13.Touch .
Configuring Ethernet Static IP Address
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch
Network & Internet
.
3. Touch
Ethernet
.
4. Place the device into the Ethernet cradle slot.
5. Slide the switch to the
ON
position.
6. Touch
Eth0
.
7. Touch
Disconnect
.
8. Touch
Eth0
.
9. Touch and hold the IP settings drop-down list and select
Static
.
10.In the
IP
address field, enter the proxy server address.
11.If required, in the
Gateway
field, enter a gateway address for the device.
12.If required, in the
Netmask
field, enter the network mask address
13.If required, in the
DNS address
fields, enter a Domain Name System (DNS) addresses.
14.Touch
CONNECT
.
15.Touch .
4-Slot Battery Charger
CAUTION
:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 189
.
This section describes how to use the 4-Slot Battery Charger to charge up to four device batteries.
142
Accessories
Setup
Figure 117
Four Slot Battery Charger Power Setup
Charging Spare Batteries
1. Connect the charger to a power source.
2. Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact.
Figure 118
4-Slot Battery Charger
Battery
Battery
Charge LED
Battery Slot
143
Accessories
3.5 mm Audio Adapter
The 3.5 mm Audio Adapter snaps onto the back of the device and removes easily when not in use. When attached to the device the 3.5 mm Audio Adapter allows a user to connect a wired headset to the device.
Connecting a Headset to the 3.5 mm Audio Adapter
1. Connect the Quick Disconnect connect of the headset to the Quick Disconnect connector of the 3.5 mm
Quick Disconnect Adapter Cable.
Figure 119
Connect Headset to Adapter Cable
2. Connect the audio jack of the 3.5 mm Quick Disconnect Adapter Cable to the 3.5 mm Audio Adapter.
Figure 120
Connect Adapter Cable to Audio Adapter
144
Accessories
Attaching the 3.5 mm Audio Adapter
1. Align the top mounting points on the 3.5 mm Audio Adapter with the mounting slots on the device.
Figure 121
Audio Adapter Installation
2. Rotate the Audio Adapter down and press down until it snaps into position.
Device with 3.5 mm Audio Adapter in Holster
When using the device and the audio adapter in a holster, ensure that the display faces in and the headset cable is securely attached to the audio adapter.
Figure 122
Device with 3.5 mm Audio Adapter in Holster
145
Accessories
Removing the 3.5 mm Audio Adapter
1. Disconnect headset plug from 3.5 mm Audio Adapter.
2. Lift the bottom of the Audio Adapter away from the device.
Figure 123
Remove Audio Adapter from Device
3. Remove Audio Adapter from the device.
Snap-On USB Cable
The Snap-On USB Cable snaps on to the back of the device and removes easily when not in use. When attached to the device the Snap-On USB Cable allows the device to transfer data to a host computer and provide power for charging the device.
Connecting to Device
1. Align the top mounting points on the cable with the mounting slots on the device.
Figure 124
Cable Installation
146
Accessories
2. Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the device.
Figure 125
Cable Attached to Device
USB Communication
1. Connect the Snap-On USB Cable to the device.
Figure 126
Cable Removed from Device
2. Connect the USB connector of the cable to a host computer.
Charging the Device
1. Connect the Snap-On USB Cable to the device.
147
Accessories
2. Connect the power supply to the Snap-On USB Cable
Figure 127
Power Setup
3. Connect to the power supply to an AC outlet.
Disconnecting from Device
1. Press down on the cable.
Figure 128
Press Down on Cable
148
Accessories
2. Rotate away from the device. The magnetics release the cable from the device.
Figure 129
Remove Cable from Device
Charging Cable Cup
This section describes how to use the Charging Cable Cup to charge the device.
Charging the Device
1. Insert the device into the cup of the Charging Cable Cup.
Figure 130
Charging
2. Ensure the device is seated properly.
149
Accessories
3. Slide the two yellow locking tabs up to lock the cable to the device.
Figure 131
Lock Cable Cup
4. Connect the power supply to the Charging Cable Cup and to a power source.
Figure 132
Connect Cable to Power Supply
Snap-On DEX Cable
The Snap-On DEX Cable snaps on to the back of the device and removes easily when not in use. When attached to the device the Snap-On DEX Cable provides electronic data exchange with devices such as vending machines.
150
Accessories
Connecting to Device
1. Align the top mounting points on the cable with the mounting slots on the device.
Figure 133
Cable Installation
2. Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the device.
Figure 134
Cable Attached to Device
DEX Communication
1. Connect the Snap-On DEX Cable to the device.
151
Accessories
2. Connect the DEX connector of the cable to a device such as a vending machine.
Figure 135
DEX Cable Connection
Disconnecting from Device
1. Press down on the cable.
Figure 136
Press Down on Cable
2. Rotate away from the device. The magnetics release the cable from the device.
Figure 137
Remove Cable from Device
152
Accessories
Trigger Handle
The Trigger Handle adds a gun-style handle with a scanning trigger to the device. It increases comfort when using the device in scan-intensive applications for extended periods of time.
NOTE
:
The Attachment Plate with Tether can only be used with Charge Only cradles.
Figure 138
Trigger Handle
Latch
Trigger
Release Button
Attachment Plate with
Tether
Attachment Plate without Tether
Installing the Attachment Plate to Trigger Handle
NOTE
:
Attachment Plate with Tether only.
To install the attachment plate to the Trigger Handle:
1. Insert the loop end of the tether into the slot on the bottom of the handle.
2. Feed the attachment plate through the loop.
Figure 139
Install Attachment Plate to Handle
3. Pull the attachment plate until the loop tightens on the tether.
153
Accessories
Installing the Trigger Handle Plate
1. Press and hold the
Power
button until the menu appears.
2. Touch
Power off
.
3. Touch
OK
.
4. Press in the two battery latches.
5. Lift the battery from the device.
6. Remove the hand strap filler plate from the hand strap slot. Store the hand strap filler plate in a safe place for future replacement.
Figure 140
Remove Hand Strap Plate
7. Insert the attachment plate into the hand strap slot.
Figure 141
Insert Trigger Handle Plate
8. Insert the battery, bottom first, into the battery compartment in the back of the device.
9. Rotate the top of the battery into the battery compartment.
10.Press the battery down into the battery compartment until the battery release latches snap into place.
154
Accessories
Inserting the Device into the Trigger Handle
1. Align the back of the Trigger handle with the Trigger Mounting Plate.
Figure 142
Connect Device to Trigger Handle
2. Press the two release latches.
155
Accessories
3. Rotate the device down and press down until it snaps into place.
Figure 143
Rotate Device onto Trigger Handle
156
Accessories
Removing the Device from the Trigger Handle
1. Press both Trigger Handle release latches.
Figure 144
Press Release Latches
157
Accessories
2. Rotate the device up and remove from the Trigger handle.
Figure 145
Rotate Device Up
158
Accessories
Vehicle Charging Cable Cup
This section describes how to use the Vehicle Charging Cable Cup to charge the device.
Figure 146
Vehicle Charging Cable Cup
159
Accessories
Charging the Device
1. Insert the device into the cup of the Vehicle Charging Cable.
Figure 147
Charging
2. Ensure the device is seated properly.
3. Slide the two yellow locking tabs up to lock the cable to the device.
Figure 148
Lock Cable Cup
160
Accessories
4. Insert the Cigarette Lighter plug into the vehicle cigarette lighter socket.
Figure 149
Connect Cable to Vehicle Power Source
Vehicle Cradle
The cradle:
• holds the device securely in place
• provides power for operating the device
• re-charges the battery in the device.
161
Accessories
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to 32V and supplies a maximum current of 3A.
Figure 150
Vehicle Cradle
Device Insertion and Removal
CAUTION
driving.
:
Ensure that the device is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while
162
Accessories
To ensure the device was inserted correctly, listen for the audible click that signifies that the device locking mechanism was enabled and the device was locked into place.
Figure 151
Install Device into Vehicle Cradle
163
Accessories
To remove the device from the cradle, grasp the device and lift out of the cradle.
Figure 152
Remove Device from Vehicle Cradle
Battery Charging
Ensure the cradle is connected to a power source.
Insert the device into the cradle. The device starts to charge through the cradle as soon as it is inserted. This
NOTE
:
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the device will only charge when its temperature is between 0°C to +40°C.
TC7X Vehicle Communication Charging Cradle
The Vehicle Communication Charging Cradle:
• holds the device securely in place
• provides power for operating the device
• re-charges the battery in the device.
The cradle is powered by the USB I/O Hub.
164
Accessories
Refer to the TC7X Vehicle Cradle Installation Guide for information on installing the TC7X Vehicle
Communication Charging Cradle.
Figure 153
TC7X Vehicle Communication Charging Cradle
165
Device Insertion and Removal
Figure 154
Insert Device into Cradle
Accessories
1
2
Figure 155
Remove Device from Cradle
1
3
2
2
To ensure the device was inserted correctly, listen for the audible click that signifies that the device locking mechanism was enabled and the device was locked into place.
CAUTION
driving.
:
Ensure that the device is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while
To remove the device from the cradle, press the release latch, grasp the device and lift out of the vehicle cradle.
Device Battery Charging
Insert the device into the cradle. The device starts to charge through the cradle as soon as it is inserted. This
Charging Note
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the device will only charge when its temperature is between 0°C to +40°C.
166
Accessories
USB I/O Hub
The USB I/O Hub:
• provides power to a vehicle cradle
• provides USB hub for three USB devices (such as printers)
• provides a powered USB port for charging another device.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to 32V and supplies a maximum current of 3A to the vehicle cradle and 1.5 A to the four USB ports simultaneously.
Refer to the device Integrator Guide for Android 8.1 Oreo for information on installing the USB I/O Hub.
Figure 156
USB I/O Hub
Connect USB Cables
The USB I/O Hub provides three USB ports for connecting devices such as printers to a device in the vehicle cradle. To connect USB cables:
167
Accessories
1. Slide the cable cover down and remove.
Figure 157
Remove Cover
2. Insert the USB cable connector into one of the USB ports.
3. Place each cable into the cable holder.
Figure 158
Connect USB Cable
4. Align the cable cover onto the USB I/O Hub. Ensure that the cables are within the cover opening.
Figure 159
Replace Cover
5. Slide cable cover up to lock into place.
External USB Cable
The USB I/O Hub provides a USB port for charging external devices such as cell phones. This port is for charging only.
168
Accessories
1. Open the USB Access Cover.
2. Insert the USB cable connector into the USB port.
Figure 160
Insert External USB Cable
USB Port
Access Cover
USB Port
Power to Vehicle Cradle
The USB I/O Hub can provide power to a Vehicle Cradle.
1. Connect the Power Output Cable connector to the Power Input Cable connector of the Vehicle Cradle.
2. Tighten thumbscrews by hand until tight.
Figure 161
Connect Power to Vehicle Cradle
2
Vehicle Cradle Power and
Communication Connector
1
Power and
Communication
Connector
Audio Headset Connection
The USB I/O Hub provides audio connection to the device in a vehicle cradle.
169
Accessories
Depending upon the headset, connect the headset and audio adapter to the Headset connector.
Figure 162
Connect Audio Headset
Headset
Adapter Cable
Collar
Hand Strap Replacement
CAUTION
:
Close all running applications prior to replacing the hand strap.
1. Press and hold the
Power
button until the menu appears.
2. Touch
Power Off
.
3. Touch
OK
.
4. Remove the hand strap clip from the hand strap mounting slot.
Figure 163
Remove Hand Strap Clip
170
5. Press the two battery latches in.
Figure 164
Press Battery Latches
Accessories
6. Lift the battery from the device.
Figure 165
Lift the Battery
7. Remove the battery.
171
Accessories
8. Remove the hand strap plate from the hand strap slot.
9. Insert the replacement hand strap plate into the hand strap slot.
Figure 166
Insert Hand Strap
10.Insert the battery, bottom first, into the battery compartment.
Figure 167
Insert Bottom of Battery into Battery Compartment
11.Rotate the top of the battery into the battery compartment.
12.Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 168
Press Down on Battery
172
Accessories
13.Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
Figure 169
Secure Hand Strap Clip
173
Application Deployment
Security
The device implements a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).
NOTE
:
Ensure the date is set correctly before installing certificates or when accessing secure web sites.
Secure Certificates
If the VPN or Wi-Fi networks rely on secure certificates, obtain the certificates and store them in the device’s secure credential storage, before configuring access to the VPN or Wi-Fi networks.
If downloading the certificates from a web site, set a password for the credential storage. The device supports
X.509 certificates saved in PKCS#12 key store files with a .p12 extension (if key store has a .pfx or other extension, change to .p12).
The device also installs any accompanying private key or certificate authority certificates contained in the key store.
Installing a Secure Certificate
To install a secure certificate:
1. Copy the certificate from the host computer to the root of the microSD card or the device’s internal memory.
See USB Communication for information about connecting the device to a host computer and copying files.
2. Go to
Settings
.
3. Touch
Security & location
>
Advanced
>
Encryption & credentials
.
4. Touch
Install from storage
.
5. Navigate to the location of the certificate file.
6. Touch the filename of the certificate to install.
7. If prompted, enter the password for credential storage. If a password has not been set for the credential storage, enter a password for it twice and then touch
OK
.
8. If prompted, enter the certificate’s password and touch
OK
.
174
Application Deployment
9. Enter a name for the certificate and in the Credential use drop-down, select
VPN and apps
or
Wi-Fi
.
10.Touch
OK
.
The certificate can now be used when connecting to a secure network. For security, the certificate is deleted from the microSD card or internal memory.
Configuring Credential Storage Settings
1. Go to
Settings
.
2. Touch
Security & location
>
Advanced
>
Encryption & credentials
.
•
Trusted credentials
- Touch to display the trusted system and user credentials.
•
User credentials
- Touch to display user credentials.
•
Install from storage
- Touch to install a secure certificate from the microSD card or internal storage.
•
Clear credentials
- Deletes all secure certificates and related credentials.
Development Tools
Android Application Development
Development Workstation
Android development tools are available at developer.android.com
.
To start developing applications for the device, download Android Studio. Development can take place on a
Microsoft® Windows®, Mac® OS X®, or Linux® operating system.
Applications are written in the Java language, but compiled and executed in the Dalvik virtual machine. Once the Java code is compiled cleanly, the developer tools make sure the application is packaged properly, including the AndroidManifest.xml file.
Android Studio contains a full featured IDE as well as SDK components required to develop Android applications.
Target Device
Open the
Developer options
screen to set development related settings.
By default, the Developer Options are hidden. To un-hide the developer options:
1. Go to
Settings
.
2. Touch
About phone
.
3. Scroll down to
Build number
.
4. Tap
Build number
seven times. The message
You are now a developer!
appears.
5. Touch .
6. Touch
System
>
Advanced
>
Developer options
.
7. Slide the
USB debugging
switch to the
ON
position.
175
Application Deployment
EMDK for Android
EMDK for Android provides developers with a comprehensive set of tools to easily create powerful line-of-business applications for enterprise mobile computing devices. It's designed for Google's Android SDK and Android Studio, and includes class libraries, sample applications with source code, and all associated documentation to help your applications take full advantage of what Zebra devices have to offer.
The kit also delivers Profile Manager, a GUI-based device configuration tool providing exclusive access to the
Zebra MX device management framework. This allows developers to configure Zebra devices from within their applications in less time, with fewer lines of code and with fewer errors.
For more information go to: techdocs.zebra.com
.
StageNow
StageNow is Zebra's next-generation Android Staging Solution built on the MX platform. It allows quick and easy creation of device profiles, and can deploy to devices simply by scanning a bar code, reading a tag, or playing an audio file.
The StageNow Staging Solution includes the following components:
• The StageNow Workstation tool installs on the staging workstation (host computer) and lets the administrator easily create staging profiles for configuring device components, and perform other staging actions such as checking the condition of a target device to determine suitability for software upgrades or other activities. The StageNow Workstation stores profiles and other created content for later use.
• The StageNow Client resides on the device and provides a user interface for the staging operator to initiate staging. The operator uses one or more of the desired staging methods (print and scan a bar code, read an
NFC tag or play an audio file) to deliver staging material to the device.
For more information go to: techdocs.zebra.com
.
GMS Restricted
GMS Restricted mode deactivates Google Mobile Services (GMS). All GMS apps are removed from the device and communication with Google (analytics data collection and location services) is disabled. It also provides enhanced security and privacy.
Use StageNow to disable or enable GMS Restricted mode. After a device is in GMS Restricted mode, enable and disable individual GMS apps and services using StageNow. To ensure GMS Restricted mode persists after an Enterprise Reset, use the Persist Manager option in StageNow. For more information on StageNow, refer to techdocs.zebra.com
.
ADB USB Setup
To use the ADB, install the USB driver. This assumes that the development SDK has been installed on the host computer. Go to developer.android.com/sdk/index.html
for details on setting up the development SDK.
ADB driver for Windows and Linux are available on the Zebra Support Central web site at www.zebra.com/support . Download the ADB and USB Driver Setup package. Follow the instructions with the package to install the ADB and USB drivers for Windows and Linux.
176
Application Deployment
Enabling USB Debugging
By default, USB debugging is disabled. To enable USB debugging:
1. Go to
Settings
.
2. Touch
About phone
.
3. Scroll down to
Build number
.
4. Tap
Build number
seven times. The message
You are now a developer!
appears.
5. Touch .
6. Touch
System
>
Advanced
>
Developer options
.
7. Slide the
USB debugging
switch to the
ON
position.
8. Touch
OK
.
9. Connect the device to the host computer using the Rugged Charge/USB Cable.
The
Allow USB debugging?
dialog box appears on the device.
10.On the device, touch
OK
.
11.On the host computer, navigate to the
platform ‐ tools
folder.
12.Type
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE
:
If device number does not appear, ensure that ADB drivers are installed properly.
13.Touch .
Application Installation
After an application is developed, install the application onto the device using one of the following methods:
• USB connection, see Installing Applications Using the USB Connection.
• Android Debug Bridge, see Installing Applications Using the Android Debug Bridge.
• microSD Card, see Installing Applications Using a microSD Card.
• Mobile device management (MDM) platforms that have application provisioning. Refer to the MDM software documentation for details.
Installing Applications Using the USB Connection
CAUTION
:
When connecting the device to a host computer and mounting the microSD card, follow the host computer’s in structions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
-
1. Connect the device to a host computer using the Rugged Charge/USB cable.
2. Pull down the Notification panel and touch
Charging this device via USB
.
177
Application Deployment
3. Touch
File Transfer
.
4. On the host computer, open a file manager application.
5. On the host computer, copy the application .apk file from the host computer to the device.
CAUTION
:
Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB devices cor rectly to avoid losing information.
-
6. Disconnect the device from the host computer.
7. Swipe the screen up and select to view files on the microSD card or Internal Storage.
8. Locate the application .apk file.
9. Touch the application file.
10.Touch
Continue
to install the app or
Cancel
to stop the installation.
11.To confirm installation and accept what the application affects, touch
Install
otherwise touch
Cancel
.
12.Touch
Open
to open the application or
Done
to exit the installation process. The application appears in the
App list.
Installing Applications Using the Android Debug Bridge
Use ADB commands to install application onto the device.
CAUTION
:
When connecting the device to a host computer and mounting its microSD card, follow the host computer’s in structions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
-
Ensure that the ADB drivers are installed on the host computer. See ADB USB Setup.
1. Connect the device to a host computer using USB. See USB Communication.
2. Go to
Settings
.
3. Touch
System
>
Advanced
>
Developer options
.
4. Slide the switch to the
ON
position.
5. Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
6. Touch
OK
.
7. On the host computer, open a command prompt window and use the adb command:
adb install <application>
where: <application> = the path and filename of the apk file.
8. Disconnect the device from the host computer. See USB Communication.
Installing Applications Using a microSD Card
CAUTION
:
When connecting the device to a host computer and mounting its microSD card, follow the host computer’s in structions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
-
1. Connect the device to a host computer using USB. See USB Communication.
178
Application Deployment
2. Copy the application APK file from the host computer to the microSD card.
3. Remove the microSD card from the host computer.
4. Press and hold the Power button on the device until the menu appears.
5. Touch
Power off
.
6. Press the two battery latches in.
7. Lift the battery from the device.
8. Lift the access door.
9. Insert the microSD card.
10.Replace the access door.
11.Insert the battery, bottom first, into the battery compartment in the back of the device.
12.Press the battery down until the battery release latches snap into place.
13.Replace the hand strap, if required.
14.Press and hold the Power button to turn on the device.
15.Swipe the screen up and select to view files on the microSD card.
16.Touch >
SD card
.
17.Locate the application .apk file.
18.Touch the application file.
19.Touch
Continue
. to install the app or
Cancel
to stop the installation.
20.To confirm installation and accept what the application affects, touch
Install
otherwise touch
Cancel
.
21.Touch
Open
to open the application or
Done
to exit the installation process. The application appears in the
App list.
Uninstalling an Application
To uninstall an application:
1. Go to
Settings
.
2. Touch
Apps & notifications
.
3. Touch
See all apps
to view all apps in the list.
4. Scroll through the list to the app.
5. Touch the app. The
App info
screen appears.
6. Touch
Uninstall
.
7. Touch
OK
to confirm.
179
Application Deployment
Performing a System Update
System Update packages can contain either partial or complete updates for the operating system. Zebra distributes the System Update packages on the Zebra Support & Downloads web site. Perform system update using either a microSD card or using ADB.
Downloading the System Update Package
To download the system update package:
1. Go to the Zebra Support & Downloads web site, www.zebra.com/support .
2. Download the appropriate System Update package to a host computer.
Using microSD Card
1. Copy the System Update zip file to the root of the microSD card.
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer, and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
2. Press and hold the Power button until the menu appears.
3. Touch
Restart
.
4. Touch
OK
. The device resets.
5. Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
6. Press the Volume Up and Volume Down buttons to navigate to
apply from sdcard
.
7. Press the Power button.
8. Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
or
Diff OTA Package
.
9. Press the Power button.
10.Press the Volume Up and Volume Down buttons to navigate to the System Update file.
11.Press the Power button. The System Update installs and then the device returns to the Recovery screen.
12.Press the Power button to reboot the device.
NOTE
:
If installing GMS software on a device that had Non-GMS software or Non-GMS software on a device that had GMS software, perform a Factory or Enterprise reset (retains enterprise data).
Using ADB
To update the system using ADB:
1. Connect the device to the Rugged Charge/USB cable or insert the device into the 1-Slot USB/Charge Only
Cradle.
180
Application Deployment
2. Connect the cable or cradle to the host computer.
3. Go to
Settings
.
4. Touch
System
>
Advanced
>
Developer options
.
5. Slide the switch to the
ON
position.
6. Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
7. Touch
OK
.
8. On the host computer, open a command prompt window and use the adb command:
adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE
:
If device number does not appear, ensure that ADB drivers are installed properly.
9. Type:
adb reboot recovery
10.Press Enter. The System Recovery screen appears.
11.Press the Volume Up and Volume Down buttons to navigate to
apply from adb
.
12.Press the Power button.
13.Use the Volume Up and Volume Down buttons to navigate to the Full OTA Package or Diff OTA Package file.
14.Press the Power button.
15.On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
16.Press Enter. The System Update installs (progress appears as percentage in the Command Prompt window) and then the Recovery screen appears.
17.Press the Power button to reboot the device.
NOTE
:
If installing GMS software on a device that had Non-GMS software or Non-GMS software on a device that had GMS software, perform a Factory or Enterprise reset (retains enterprise data).
Verify System Update Installation
To check that the system update installed properly:
1. Go to
Settings
.
2. Touch
About phone
.
3. Scroll down to
Build number
.
4. Ensure that the build number matches the new system update package file number.
181
Application Deployment
Performing an Enterprise Reset
An Enterprise Reset erases all user data in the
/data
partition, including data in the primary storage locations
(
/sdcard
and emulated storage).
Before performing an Enterprise Reset, provision all necessary configuration files and restore after the reset.
Perform Enterprise Reset using either a microSD card or using ADB.
Downloading the Enterprise Reset Package
To download the system update package:
1. Go to the Zebra Support & Downloads web site, www.zebra.com/support .
2. Download the Enterprise Reset file to a host computer.
Using microSD Card
1. Copy the Enterprise Reset zip file to the root of the microSD card.
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
2. Press and hold the Power button until the menu appears.
3. Touch
Restart
.
4. Touch
OK
. The device resets.
5. Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
6. Press the Volume Up and Volume Down buttons to navigate to
apply from sdcard
.
7. Press the Power button.
8. Use the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
9. Press the Power button.
10.Use the Volume Up and Volume Down buttons to navigate to the Enterprise Reset file.
11.Press the Power button. The Enterprise Reset occurs and then the device returns to the Recovery screen.
12.Press the Power button.
Using ADB
To perform an Enterprise Reset using ADB:
1. Connect the device to the Rugged Charge/USB cable or insert the device into the 1-Slot USB/Charge Only
Cradle.
182
Application Deployment
2. Connect the cable or cradle to the host computer.
3. Go to
Settings
.
4. Touch
System
>
Advanced
>
Developer options
.
5. Slide the switch to the
ON
position.
6. Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
7. Touch
OK
.
8. On the host computer, open a command prompt window and type:
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE
:
If device number does not appear, ensure that ADB drivers are installed properly.
9. Type:
adb reboot recovery
10.Press Enter. The System Recovery screen appears.
11.Press the Volume Up and Volume Down buttons to navigate to
apply from adb
.
12.Press the Power button.
13.Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
14.Press the Power button.
15.On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
16.Press Enter. The Enterprise Reset package installs and then the Recovery screen appears.
17.Press the Power button to reboot the device.
Performing a Factory Reset
A Factory Reset erases all data in the
/data
and
/enterprise
partitions in internal storage and clears all device settings. A Factory Reset returns the device to the last installed operating system image. To revert to a previous operating system version, re-install that operating system image. See Performing a System Update for more information.
Downloading the Factory Reset Package
To download the Factory Reset package:
1. Go to the Zebra Support & Downloads web site, www.zebra.com/support .
2. Download the appropriate Factory Reset file to a host computer.
183
Application Deployment
Using microSD Card
1. Copy the Factory Reset zip file to the root of the microSD card.
• Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
• Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
2. Press and hold the Power button until the menu appears.
3. Touch
Reboot
.
4. Touch
OK
. The device resets.
5. Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
6. Press the Volume Up and Volume Down buttons to navigate to
apply from sdcard
.
7. Press the Power button.
8. Use the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
9. Press the Power button.
10.Use the Volume Up and Volume Down buttons to navigate to the Factory Reset file.
11.Press the Power button. The Factory Reset occurs and then the device returns to the Recovery screen.
12.Press the Power button.
Using ADB
To perform an Factory Reset using ADB:
1. Connect the device to the Rugged Charge/USB cable or insert the device into the 1-Slot USB/Charge Only
Cradle.
2. Connect the cable or cradle to the host computer.
3. Go to
Settings
.
4. Touch
System
>
Advanced
>
Developer options
.
5. Slide the switch to the
ON
position.
6. Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
7. Touch
OK
.
8. On the host computer, open a command prompt window and type:
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
184
Application Deployment
NOTE
:
If device number does not appear, ensure that ADB drivers are installed properly.
9. Type:
adb reboot recovery
10.Press Enter. The System Recovery screen appears.
11.Press the Volume Up and Volume Down buttons to navigate to
apply from adb
.
12.Press the Power button.
13.Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
14.Press the Power button.
15.On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
16.Press Enter. The Factory Reset package installs and then the Recovery screen appears.
17.Press the Power button to reboot the device.
Storage
The device contains the following types of file storage:
• Random Access Memory (RAM)
• Internal storage
• External storage (microSD card) or
• Enterprise folder.
Random Access Memory
Executing programs use RAM to store data. Data stored in RAM is lost upon a reset. The operating system manages how applications use RAM. It only allows applications and component processes and services to use
RAM when required. It may cache recently used processes in RAM, so they restart more quickly when opened again, but it will erase the cache if it needs the RAM for new activities.
1. Go to
Settings
.
2. Touch
System
>
Advanced
>
Developer options
>
Memory
.
The screen displays the amount of used and free RAM.
•
Performance
- Indicates memory performance.
•
Total memory
- Indicates the total amount of RAM available.
•
Average used (%)
- Indicates the average amount of memory (as a percentage) used during the period of time selected (default - 3 hours).
•
Free
- Indicates the total amount of unused RAM.
•
Memory used by apps
- Touch to view RAM usage by individual apps.
185
Application Deployment
Internal Storage
The device has internal storage. The internal storage content can be viewed and files copied to and from when the device is connected to a host computer. Some applications are designed to be stored on the internal storage rather than in internal memory.
To view the used and available space on the internal storage:
1. Go to
Settings
.
2. Touch
Storage
.
•
Internal Storage
- Displays the total amount of space on internal storage and amount used.
Touch
Internal shared storage
to display a the amount of storage used by apps, photos, videos, audio and other files.
External Storage
The device can have a removable microSD card. The microSD card content can be viewed and files copied to and from when the device is connected to a host computer.
To view the used and available space on the microSD card:
1. Go to
Settings
.
2. Touch
Storage
.
Portable storage displays the total amount of space on the installed microSD card and the amount used.
To unmount the microSD card, touch .
Touch
SD card
to view the contents of the card.
Formatting a microSD Card or USB Drive as Portable Storage
To format an installed microSD card or USB drive as portable storage:
1. Touch
SD card
.
2. Touch >
Storage settings
.
3. Touch
Format
.
4. Touch
ERASE & FORMAT
.
5. Touch
DONE
.
Formatting a microSD Card as Internal Memory
You can format a microSD card as internal memory to increase the actual amount of the device’s internal memory. Once formatted, the microSD card can only be read by this device. To format an installed microSD card as internal memory:
1. Touch
SD card
.
2. Touch >
Storage settings
.
3. Touch
Format as internal
.
186
Application Deployment
4. Touch
ERASE & FORMAT
.
5. Touch
DONE
.
Enterprise Folder
The Enterprise folder (within internal flash) is a super-persistent storage that is persistent after a reset and an
Enterprise Reset. The Enterprise folder is erased during a Factory Reset. The Enterprise folder is used for deployment and device-unique data. The Enterprise folder is approximately 128 MB (formatted). Applications can persist data after an Enterprise Reset by saving data to the enterprise/user folder. The folder is ext4 formatted and is only accessible from a host computer using ADB or from an MDM.
App Management
Apps use two kinds of memory: storage memory and RAM. Apps use storage memory for themselves and any files, settings, and other data they use. They also use RAM when they are running.
1. Go to
Settings
.
2. Touch
Apps & notifications
.
3. Touch
See all XX apps
to view all apps on the device.
4. Touch >
Show system
to include system processes in the list.
5. Touch an app, process, or service in the list to open a screen with details about it and, depending on the item, to change its settings, permissions, notifications and to force stop or uninstall it.
Viewing App Details
Apps have different kinds of information and controls, but commonly include:
•
Force stop
- stop an app.
•
Disable
- disable an app.
•
Uninstall
- remove the app and all of its data and settings from the device. See Uninstalling an Application for information about uninstalling apps.
•
Storage
- lists how much information is stored, and includes a button for clearing it.
•
Data usage
- provides information about data (Wi-Fi) consumed by an app.
•
Permissions
- lists the areas on the device that the app has access to.
•
Notifications
- set the app notification settings.
•
Open by default
- clears If you have configured an app to launch certain file types by default, you can clear that setting here.
•
Battery
- lists the amount of computing power used by the app.
•
Memory
- lists the average app memory usage.
• Advanced
•
Draw over other apps
- allows an app to display on top of other apps.
187
Application Deployment
Managing Downloads
Files and apps downloaded using the Browser or Email are stored on the microSD card or Internal storage in the Download directory. Use the Downloads app to view, open, or delete downloaded items.
1. Swipe the screen up and touch .
2. Touch >
Downloads
.
3. Touch and hold an item, select items to delete and touch . The item is deleted from the device.
188
Maintenance and
Troubleshooting
Maintaining the Device
For trouble-free service, observe the following tips when using the device:
• To avoid scratching the screen, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the device screen.
• The touch-sensitive screen of the device is glass. Do not drop the device or subject it to strong impact.
• Protect the device from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
• Do not store the device in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the device. If the surface of the device screen becomes soiled, clean it with a soft cloth moistened with an approved cleanser. For a list of approved cleansers, see Approved Cleanser Active
Ingredients.
• Periodically replace the rechargeable battery to ensure maximum battery life and product performance. Battery life depends on individual usage patterns.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in this guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the ambient battery and charger temperatures must be between +32ºF and +104ºF (0ºC and +40ºC).
• Do not use incompatible batteries and chargers, including non-Zebra batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact the Global Customer Support Center.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred the battery.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
189
Maintenance and Troubleshooting
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to properly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with water for 15 minutes, and seek medical advice.
• If you suspect damage to your equipment or battery, contact Customer Support to arrange for inspection.
Cleaning Instructions
CAUTION
:
Always wear eye protection.
Read warning label on alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support Center for more information.
WARNING
:
Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite chloride, or mild dish soap.
1 (see important note below)
, hydrogen peroxide, ammonium
IMPORTANT
:
Use pre-moistened wipes and do not allow liquid cleaner to pool.
1
When using sodium hypochlorite (bleach) based products, always follow the manufacturer’s recommended instructions: use gloves during application and remove the residue afterwards with a damp alcohol cloth or a cotton swab to avoid prolonged skin contact while handling the device.
Due to the powerful oxidizing nature of sodium hypochlorite, the metal surfaces on the device are prone to oxidation
(corrosion) when exposed to this chemical in the liquid form (including wipes). In the event that these type of disinfectants come in contact with metal on the device, prompt removal with an alcohol-dampened cloth or cotton swab after the cleaning step is critical.
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; aqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device.
Device Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, instead gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Before use, allow the unit to air dry.
190
Maintenance and Troubleshooting
NOTE
:
For thorough cleaning, it is recommended to first remove all accessory attachments, such as hand straps or cradle cups, from the mobile device and to clean them separately.
Special Cleaning Notes
The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed.
If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the device.
IMPORTANT
:
If the battery connectors are exposed to cleaning agents, thoroughly wipe off as much of the chemical as possible and clean with an alcohol wipe. It is also recommended to install the battery in the terminal prior to cleaning and disinfecting the device to help minimize buildup on the connectors.
When using cleaning/disinfectant agents on the device, it is important to follow the directions prescribed by the cleaning/disinfectant agent manufacturer.
Cleaning Materials Required
• Alcohol wipes
• Lens tissue
• Cotton-tipped applicators
• Isopropyl alcohol
• Can of compressed air with a tube.
Cleaning Frequency
The cleaning frequency is at the customer’s discretion due to the varied environments in which the mobile devices are used and may be cleaned as frequently as required. When dirt is visible, it is recommended to clean the mobile device to avoid build up of particles which make the device more difficult to clean later on.
For consistency and optimum image capture, it is recommended to clean the camera window periodically especially when used in environments prone to dirt or dust.
Cleaning the Device
Housing
Thoroughly wipe the housing, including all buttons and triggers, using an approved alcohol wipe.
Display
The display can be wiped down with an approved alcohol wipe, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
191
Maintenance and Troubleshooting
Camera and Exit Window
Wipe the camera and exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
Cleaning Battery Connectors
To clean the battery connectors:
1. Remove the main battery from the mobile computer.
2. Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3. To remove any grease or dirt, rub the cotton portion of the cotton-tipped applicator back-and-forth across the connectors on the battery and terminal sides. Do not leave any cotton residue on the connectors.
4. Repeat at least three times.
5. Use a dry cotton-tipped applicator and repeat steps 3 and 4. Do not leave any cotton residue on the connectors.
6. Inspect the area for any grease or dirt and repeat the cleaning process if necessary.
CAUTION
:
After cleaning the battery connectors with bleach-based chemicals, follow the Battery Connector Cleaning in structions to remove bleach from the connectors.
-
Cleaning Cradle Connectors
To clean the connectors on a cradle:
1. Remove the DC power cable from the cradle.
2. Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3. Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
4. All sides of the connector should also be rubbed with the cotton-tipped applicator.
5. Remove any lint left by the cotton-tipped applicator.
6. If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
7. Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and low humidity requires less drying time.
CAUTION
:
After cleaning the cradle connectors with bleach-based chemicals, follow the Cleaning Cradle Connectors in structions to remove bleach from the connectors.
-
192
Maintenance and Troubleshooting
Troubleshooting
Performing a Soft Reset
Perform a soft reset if applications stop working.
1. Press and hold the Power button until the menu appears.
2. Touch
Restart
.
The device reboots.
Performing a Hard Reset
TC72
CAUTION
:
Performing a hard reset with a microSD card installed in the device may cause damage or data corruption to the microSD card. All un-saved data is lost after performing a hard reset.
Perform a hard reset if the device stops responding.
1. Simultaneously press the Power, Scan and Volume Up buttons for at least four seconds.
2. When the screen turns off, release the buttons.
The device reboots.
The following tables provides typical problems that might arise and the solution for correcting the problem.
Table 19
Troubleshooting the TC72
Problem
When pressing the power button the device does not turn on.
When pressing the power button the device does not turn on but two LEDs blink.
Battery did not charge.
Cause
Battery not charged.
Battery not installed properly.
System crash.
Battery charge is at a level where data is maintained but battery should be re-charged.
Cannot see characters on display.
Solution
Charge or replace the battery in the device.
Install the battery properly.
Perform a reset.
Charge or replace the battery in the device.
Battery failed.
Device removed from cradle while battery was charging.
Replace battery. If the device still does not operate, perform a reset.
Insert device in cradle. The 4,620 mAh battery fully charges in less than five hours at room temperature.
Extreme battery temperature.
Battery does not charge if ambient temperature is below
0°C (32°F) or above 40°C (104°F).
Device not powered on. Press the
Power
button.
193
Maintenance and Troubleshooting
Table 19
Troubleshooting the TC72
Problem
During data communication with a host computer, no data transmitted, or transmitted data was incomplete.
Cause
Device removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Communication software was incorrectly installed or configured.
Wi-Fi radio is not on.
You moved out of range of an access point.
During data communication over
Wi-Fi, no data transmitted, or transmitted data was incomplete.
During data communication over
WAN, no data transmitted, or transmitted data was incomplete.
During data communication over
Bluetooth, no data transmitted, or transmitted data was incomplete.
No sound.
Device shuts off.
You are in an area of poor cellular service.
APN is not set up correctly.
SIM card not installed properly.
Volume setting is low or turned off.
Device is inactive.
Adjust the volume.
Solution
Replace the device in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Perform setup.
Turn on the Wi-Fi radio.
Move closer to an access point.
Move into an area that has better service.
See system administrator for APN setup information.
Remove and re-install the SIM card.
Data plan not activated. Contact your service provider and ensure that your data plan is enable.
Bluetooth radio is not on.
Turn on the Bluetooth radio.
You moved out of range of another Bluetooth device.
Move within 10 meters (32.8 feet) of the other device.
The display turns off after a period of inactivity. Set this period to 15 seconds, 30 seconds, 1, 2, 5, 10 or 30 minutes.
Replace the battery.
Reset the device.
Tapping the window buttons or icons does not activate the corresponding feature.
Battery is depleted.
The device is not responding.
194
Maintenance and Troubleshooting
Table 19
Troubleshooting the TC72
Problem
A message appears stating that the device memory is full.
The device does not decode with reading bar code.
Device cannot find any Bluetooth devices nearby.
Cannot unlock device.
Cause
Too many files stored on the device.
Too many applications installed on the device.
Scanning application is not loaded.
Unreadable bar code.
Distance between exit window and bar code is incorrect.
Device is not programmed for the bar code.
Device is not programmed to generate a beep.
Battery is low.
Solution
Delete unused memos and records. If necessary, save these records on the host computer (or use an SD card for additional memory).
Remove user-installed applications on the device to recover memory. Select >
Storage
>
FREE UP
SPACE
>
REVIEW RECENT ITEMS
. Select the unused program(s) and tap
FREE UP
.
Load a scanning application on the device or enable
DataWedge. See the system administrator.
Ensure the symbol is not defaced.
Place the device within proper scanning range.
Program the device to accept the type of bar code being scanned. Refer to the EMDK or DataWedge application.
If the device does not beep on a good decode, set the application to generate a beep on good decode.
Too far from other
Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
The Bluetooth device(s) are not in discoverable mode.
User enters incorrect password.
If the scanner stops emitting a laser beam upon a trigger press, check the battery level. When the battery is low, the scanner shuts off before the device low battery condition notification. Note: If the scanner is still not reading symbols, contact the distributor or the Global
Customer Support Center.
Move closer to the other Bluetooth device(s), within a range of 10 meters (32.8 feet).
Turn on the Bluetooth device(s) to find.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
If the user enters an incorrect password eight times, the user is requested to enter a code before trying again.
If the user forgot the password, contact system administrator.
195
Maintenance and Troubleshooting
2-Slot Charge Only Cradle
Table 20
Troubleshooting the 2-Slot Charge only Cradle
Symptom
LEDs do not light when device or spare battery is inserted.
Device battery is not charging.
Possible Cause
Cradle is not receiving power.
Device is not seated firmly in the cradle.
Spare battery is not seated firmly in the cradle.
Device was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
Action
Ensure the power cable is connected securely to both the cradle and to AC power.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Remove and re-insert the spare battery into the charging slot, ensuring it is firmly seated.
Ensure cradle is receiving power. Ensure device is seated correctly. Confirm main battery is charging. The
4,620 mAh battery fully charges in less than five hours.
Spare battery is not charging.
The device is not fully seated in the cradle.
Extreme battery temperature.
Battery not fully seated in charging slot.
Battery inserted incorrectly.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 0 °C (32 °F) or above 40 °C (104 °F).
Remove and re-insert the spare battery in the cradle, ensuring it is firmly seated. The 4,620 mAh battery fully charges in less than five hours.
Re-insert the battery so the charging contacts on the battery align with the contacts on the cradle.
Verify that other batteries charge properly. If so, replace the faulty battery.
196
Maintenance and Troubleshooting
2-Slot USB/Ethernet Cradle
Table 21
Troubleshooting the 2-Slot USB/Ethernet Cradle
Symptom
During communication, no data transmits, or transmitted data was incomplete.
LEDs do not light when device or spare battery is inserted.
Device battery is not charging.
Possible Cause
Device removed from cradle during communications.
Incorrect cable configuration.
Device has no active connection.
USB/Ethernet module switch in not in the correct position.
Cradle is not receiving power.
Device is not seated firmly in the cradle.
Spare battery is not seated firmly in the cradle.
Device was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
Action
Replace device in cradle and retransmit.
Ensure that the correct cable configuration.
An icon is visible in the status bar if a connection is currently active.
For Ethernet communication, slide the switch to the
position. For USB communication, slide the switch to the position.
Ensure the power cable is connected securely to both the cradle and to AC power.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Remove and re-insert the spare battery into the charging slot, ensuring it is firmly seated.
Ensure cradle is receiving power. Ensure device is seated correctly. Confirm main battery is charging. The
4,620 mAh battery fully charges in less than five hours.
Spare battery is not charging.
The device is not fully seated in the cradle.
Extreme battery temperature.
Battery not fully seated in charging slot.
Battery inserted incorrectly.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 0 °C (32 °F) or above 40 °C (104 °F).
Remove and re-insert the spare battery in the cradle, ensuring it is firmly seated. The 4,620 mAh battery fully charges in less than five hours.
Re-insert the battery so the charging contacts on the battery align with the contacts on the cradle.
Verify that other batteries charge properly. If so, replace the faulty battery.
197
Maintenance and Troubleshooting
5-Slot Charge Only Cradle
Table 22
Troubleshooting the 5-Slot Charge Only Cradle
Problem
Battery is not charging.
Cause
Device removed from the cradle too soon.
Replace the device in the cradle. The battery fully charges in approximately five hours.
Solution
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Device is not inserted correctly in the cradle.
Remove the device and reinsert it correctly. Verify charging is active. Touch >
Information
System
>
About phone
to view battery status.
>
Battery
Ambient temperature of the cradle is too warm.
Move the cradle to an area where the ambient temperature is between -10 °C (+14 °F) and +60 °C (+140 °F).
198
Maintenance and Troubleshooting
5-Slot Ethernet Cradle
Table 23
Troubleshooting the 5-Slot Ethernet Cradle
Problem
During communication, no data transmits, or transmitted data was incomplete.
Battery is not charging.
Cause
Device removed from cradle during communication s.
Incorrect cable configuration.
Device has no active connection.
Solution
Replace device in cradle and retransmit.
Ensure that the correct cable configuration.
An icon is visible in the status bar if a connection is currently active.
Device removed from the cradle too soon.
Replace the device in the cradle. The battery fully charges in approximately five hours.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Device is not inserted correctly in the cradle.
Ambient temperature of the cradle is too warm.
Remove the device and reinsert it correctly. Verify charging is active. Touch >
System
>
About phone
>
Battery
Information
to view battery status.
Move the cradle to an area where the ambient temperature is between -10 °C (+14 °F) and +60 °C (+140 °F).
4-Slot Battery Charger
Table 24
Troubleshooting the 4-Slot Battery Charger
Problem
Spare Battery
Charging LED does not light when spare battery is inserted.
Cause
Spare battery is not correctly seated.
Solution
Remove and re-insert the spare battery into the charging slot, ensuring it is correctly seated.
199
Maintenance and Troubleshooting
Table 24
Troubleshooting the 4-Slot Battery Charger (Continued)
Problem
Spare Battery not charging.
Cause
Charger is not receiving power.
Spare battery is not correctly seated.
Battery adapter is not seated properly.
Ensure the power cable is connected securely to both the charger and to AC power.
Solution
Remove and re-insert the battery into the battery adapter, ensuring it is correctly seated.
Remove and re-insert the battery adapter into the charger, ensuring it is correctly seated.
Battery was removed from the charger or charger was unplugged from
AC power too soon.
Ensure charger is receiving power. Ensure the spare battery is seated correctly. If a battery is fully depleted, it can take up to five hours to fully recharge a Standard Battery and it can take up to eight hours to fully recharge an Extended Life Battery.
Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
200
Technical Specifications
For device technical specifications, go to www.zebra.com/support .
Data Capture Supported Symbologies
Table 25
Data Capture Supported Symbologies
Item
1D Bar Codes
2D Bar Codes
Description
Code 128, EAN-8, EAN-13, GS1 DataBar Expanded, GS1 128, GS1 DataBar
Coupon, UPCA, Interleaved 2 of 5, UPC Coupon Code
PDF-417, QR Code, Digimarc, Dotcode
SE4750-SR Decode Distances
The table below lists the typical distances for selected bar code densities. The minimum element width (or
“symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol.
Table 26
SE4750-SR Decode Distances
Symbol Density/ Bar Code Type
3 mil Code 39
5.0 mil Code 128
5 mil PDF417
6.67 mil PDF417
10 mil Data Matrix
100% UPCA
4.1 in.
10.41 cm
3.5 in.
8.89 cm
4.4 in.
11.18 cm
3.2 in.
8.13 cm
3.3 in.
8.38 cm
2.0 in.
5.08 cm
Near
Typical Working Ranges
Far
4.9 in.
12.45 cm
6.8 in.
17.27 cm
6.3 in.
16.00 cm
8.1 in.
20.57 cm
8.5 in.
21.59 cm
18.0 in.
45.72 cm
201
Technical Specifications
Table 26
SE4750-SR Decode Distances
Symbol Density/ Bar Code Type
Near
Typical Working Ranges
Far
15 mil Code 128
20 mil Code 39
2.6 in.
6.06 cm
1.8 in.
4.57 cm
19.8 in.
50.29 cm
27.0 in.
68.58 cm
Note: Photographic quality bar code at 18° tilt pitch angle under 30 fcd ambient illumination.
I/O Connector Pin-Outs
Pin 1
Figure 170
I/O Connector
Table 27
I/O Connector Pin-Outs
6
7
4
5
1
2
3
8
9
10
Pin
GND
Signal
RXD_MIC
PWR_IN_CON
TRIG_PTT
GND
USB-OTG_ID
TXD_EAR
USB_OTG_VBUS
USB_OTG_DP
USB_OTG_DM
Description
Power/signal ground.
UART RXD + Headset microphone.
External 5.4 VDC power input.
Trigger or PTT input.
Power/signal ground.
USB OTG ID pin.
UART TXD, Headset ear.
USB VBUS
USB DP
USB DM
202
Technical Specifications
2-Slot Charge Only Cradle Technical Specifications
Table 28
2-Slot Charge Only Cradle Technical Specifications
Dimensions
Weight
Item
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 10.6 cm (4.17 in.)
Width: 19.56 cm (7.70 in.)
Depth: 13.25 cm (5.22 in.)
748 g (26.4 oz.)
12 VDC
30 watts
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10 kV contact
+/- 10 kV indirect discharge
2-Slot USB/Ethernet Cradle Technical Specifications
Table 29
2-Slot USB/Ethernet Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 20 cm (7.87 in.)
Width: 19.56 cm (7.70 in.)
Depth: 13.25 cm (5.22 in.)
870 g (30.7 oz.)
12 VDC
30 watts
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
203
Technical Specifications
5-Slot Charge Only Cradle Technical Specifications
Table 30
5-Slot Charge Only Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 90.1 mm (3.5 in.)
Width: 449.6 mm (17.7 in.)
Depth: 120.3 mm (4.7 in.)
1.31 kg (2.89 lbs.)
12 VDC
65 watts
90 watts with 4–Slot Battery Charger installed.
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
0% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
5-Slot Ethernet Cradle Technical Specifications
Table 31
5-Slot Ethernet Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 21.7 cm (8.54 in.)
Width: 48.9 cm (19.25 in.)
Depth: 13.2 cm (5.20 in.)
2.25 kg (4.96 lbs)
12 VDC
65 watts
90 watts with 4-Slot Battery Charger installed.
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
204
Technical Specifications
4-Slot Battery Charger Technical Specifications
Table 32
4–Slot Battery Charger Technical Specifications
Dimensions
Weight
Item
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 4.32 cm (1.7 in.)
Width: 20.96 cm (8.5 in.)
Depth: 15.24 cm (6.0 in.)
386 g (13.6 oz.)
12 VDC
40 watts
0 °C to 40 °C (32 °F to 104 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
Charge Only Vehicle Cradle Technical Specifications
Table 33
Charge Only Vehicle Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 12.3 cm (4.84 in.)
Width: 11.0 cm (4.33 in.)
Depth: 8.85 cm (3.48 in.)
320 g (11.3 oz.)
12/24 VDC
40 watts
-40 °C to 85 °C (-40 °F to 185 °F)
-40 °C to 85 °C (-40 °F to 185 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
205
Technical Specifications
Trigger Handle Technical Specifications
Table 34
Trigger Handle Technical Specifications
Dimensions
Weight
Item
Operating Temperature
Storage Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 11.2 cm (4.41 in.)
Width: 6.03 cm (2.37 in.)
Depth: 13.4 cm (5.28 in.)
110 g (3.8 oz.)
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
1.8 m (6 feet) drops to concrete over temperature range.
+/- 20kV air
+/- 10kV contact
Charging Cable Cup Technical Specifications
Table 35
Charging Cable Cup Technical Specifications
Item
Length
Input Voltage
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
25.4 cm (10.0 in.)
5.4 VDC
-20 °C to 50 °C (-4 °F to 122 °F)
Description
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
Snap-On USB Cable Technical Specifications
Table 36
Snap-On USB Cable Technical Specifications
Item
Length
Input Voltage
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
1.5 cm (60.0 in.)
5.4 VDC (external power supply)
-20 °C to 50 °C (-4 °F to 122 °F)
Description
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
206
Technical Specifications
DEX Cable Technical Specifications
Table 37
DEX Cable Technical Specifications
Item
Length
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
Description
1.5 cm (60.0 in.)
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
207
Index
A
adaptive frequency hopping . . . . . . . . . . . . . . . . . . . . 98
ambient display setting . . . . . . . . . . . . . . . . . . . . . . . . 41
apps
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
datawedge demonstration . . . . . . . . . . . . . . . . . . . 60
device central . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
diagnostic tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PTT Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
RxLogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
sound recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
B barcode scanning
digital camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
DS3678 digital scanner . . . . . . . . . . . . . . . . . . . . . 76
integrated imager . . . . . . . . . . . . . . . . . . . . . . . . . 74
battery
battery manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
battery optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
battery safety guidelines . . . . . . . . . . . . . . . . . . . . . . 189
bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91, 97
change name . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
208
C
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49, 55
front camera photo settings . . . . . . . . . . . . . . . . . 58
front camera video settings . . . . . . . . . . . . . . . . . 59
rear camera video settings . . . . . . . . . . . . . . . . . . 59
recording videos . . . . . . . . . . . . . . . . . . . . . . . . . . 57
taking panoramic photos . . . . . . . . . . . . . . . . . . . 56
taking photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
video settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59
cast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
change bluetooth name . . . . . . . . . . . . . . . . . . . . . . . 101
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190, 191
instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
cleaning instructions . . . . . . . . . . . . . . . . . . . . . . . . . 190
cradle
connector cleaning . . . . . . . . . . . . . . . . . . . . . . . 192
D data capture
digital camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
DS3678 digital scanner . . . . . . . . . . . . . . . . . . . . 76
integrated imager . . . . . . . . . . . . . . . . . . . . . . . . . 74
data capture options . . . . . . . . . . . . . . . . . . . . . . . . . . 12
datawedge demonstration . . . . . . . . . . . . . . . . . . . . . . 60
decoders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
device central . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Index
my device tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
paging an RS6000 ring scanner . . . . . . . . . . . . . . 63
peripherals tab . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
scan and pair tab . . . . . . . . . . . . . . . . . . . . . . . . . 61
unpairing a peripheral . . . . . . . . . . . . . . . . . . . . . . 63
diagnostic tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
battery test information . . . . . . . . . . . . . . . . . . . . . 65
bluetooth test information . . . . . . . . . . . . . . . . . . . 66
gps test information . . . . . . . . . . . . . . . . . . . . . . . . 65
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
wwan test information . . . . . . . . . . . . . . . . . . . . . . 66
disable bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
disconnect host computer . . . . . . . . . . . . . . . . . . . . . . 38
discover bluetooth devices . . . . . . . . . . . . . . . . . . . . 100
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DS3678
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
DS3678 digital scanner
E
EAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
enable bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
F
file transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
finger usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
G
general sound setting . . . . . . . . . . . . . . . . . . . . . . . . . 43
H
hard reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
harmful ingredients . . . . . . . . . . . . . . . . . . . . . . . . . . 190
home screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
I integrated imager
barcode scanning . . . . . . . . . . . . . . . . . . . . . . . . . 74
209
data capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
operational modes . . . . . . . . . . . . . . . . . . . . . . . . .74
interactive sensor technology . . . . . . . . . . . . . . . . . . .37
K
keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
additional character tab . . . . . . . . . . . . . . . . . . . . .46
alpha tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
editing text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
entering numbers, symbols, and special characters .
numeric tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
L
low battery notification . . . . . . . . . . . . . . . . . . . . . . . . .36
M maintenance
approved cleanser active ingredients . . . . . . . . .190
battery safety guidelines . . . . . . . . . . . . . . . . . . .189
clean battery connectors . . . . . . . . . . . . . . . . . . .192
clean camera and exit window . . . . . . . . . . . . . .192
clean cradle connectors . . . . . . . . . . . . . . . . . . .192
clean display . . . . . . . . . . . . . . . . . . . . . . . . . . . .191
clean housing . . . . . . . . . . . . . . . . . . . . . . . . . . .191
cleaning frequency . . . . . . . . . . . . . . . . . . . . . . .191
cleaning instructions . . . . . . . . . . . . . . . . . . . . . .190
cleaning materials required . . . . . . . . . . . . . . . . .191
device cleaning instructions . . . . . . . . . . . . . . . .190
harmful ingredients . . . . . . . . . . . . . . . . . . . . . . .190
maintaining the device . . . . . . . . . . . . . . . . . . . . .189
special cleaning notes . . . . . . . . . . . . . . . . . . . . .191
managing notifications . . . . . . . . . . . . . . . . . . . . . . . . .33
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
message URL http
//techdocs.zebra.com/datawedge/ . . . . . . . . . . . . .88
monitor battery usage . . . . . . . . . . . . . . . . . . . . . . . . .36
N
near field communication . . . . . . . . . . . . . . . . . . . . . . .91
near field communications . . . . . . . . . . . . . . . . . . . . .102
NFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
reading cards . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
sharing information . . . . . . . . . . . . . . . . . . . . . . .103
notational conventions . . . . . . . . . . . . . . . . . . . . . . . . .12
notification icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
notifications
managing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Index
O
operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
operational modes
P pairing
DS3678 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
RS507/RS6000 hands-free imager . . . . . . . . . . . . 83
using Bluetooth HID (RS507/RS6000) . . . . . . . . . 85
using Bluetooth HID(DS3678) . . . . . . . . . . . . . . . . 86
using simple serial interface(RS507/RS6000) . . . 84
Pairing Using Bluetooth Human Interface Device . . . . 85
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
photo transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
photos
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
taking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
PTT Express
audible indicators . . . . . . . . . . . . . . . . . . . . . . . . . 68
disabling communication . . . . . . . . . . . . . . . . . . . . 70
enabling communication . . . . . . . . . . . . . . . . . . . . 68
group calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
notification icons . . . . . . . . . . . . . . . . . . . . . . . . . . 68
user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Voice Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
PTT-Express
PTT communication . . . . . . . . . . . . . . . . . . . . . . . 69
Q
quick access panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
R
radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
reading NFC cards . . . . . . . . . . . . . . . . . . . . . . . . . . 102
remove wi-fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
reset device
RS507
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
RS507 hands-free imager . . . . . . . . . . . . . . . . . . . . . . 75
RS507 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . 79, 82
RS507/RS6000
pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
pairing using Bluetooth HID . . . . . . . . . . . . . . . . . 85
pairing using simple serial interface . . . . . . . . . . . 84
210
RS6000
bluetooth ring scanner . . . . . . . . . . . . . . . . . . . . . .75
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
RS6000 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
RxLogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
configuration file . . . . . . . . . . . . . . . . . . . . . . . . . .71
disable logging . . . . . . . . . . . . . . . . . . . . . . . . . . .71
enable logging . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
extract log files . . . . . . . . . . . . . . . . . . . . . . . . . . .71
RxLogger Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
S scanning
considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
DS3678 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
RS507 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
RS6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
screen font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
screen rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . .39, 40
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
setting
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58, 59
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39, 91
accessing . . . . . . . . . . . . . . . . . . . . . . . . . . . .39, 91
ambient display . . . . . . . . . . . . . . . . . . . . . . . . . . .41
camera photos . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
camera videos . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
general sound . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
sharing information using NFC . . . . . . . . . . . . . . . . .103
soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
software version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
software versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
sound recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201
T
taking a panoramic photo . . . . . . . . . . . . . . . . . . . . . . .56
touch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
transferring files using USB . . . . . . . . . . . . . . . . . . . . .37
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
TC75x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
U
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
V
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . . . . .164, 167
videos
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
W
WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Wi-Fi direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
wireless local area network . . . . . . . . . . . . . . . . . . . . . 91
WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
WPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Index
211
www.zebra.com
İndir
Herkese açık bağlantı güncellendi
Sohbetinize giden herkese açık bağlantı güncellendi. You may view and manage your chat links after registration here.
Belge herkese açık bağlantısı
Reklam