Quick Installation Guide
N300 Wi-Fi ADSL2+ Modem Router
D301V4
Package contents
Modem router
Power adapter
Ethernet cable (RJ45)
Phone cable (RJ11)
ADSL splitter
Quick installation guide
If any item is missing or damaged, please keep the original package and contact the local reseller or distributor immediately.
For product or function details, please go to http://www.tendacn.com
Getting to know your modem router
LED indicators
LED indicator
Power LED indicator
DSL LED indicator
Status
Solid on
Off
Description
The modem router is connected to a power source properly.
The modem router is not powered on.
Solid on
Internet LED indicator
Off
WPS LED indicator
Solid on for 5 mins->Off
Blinking
Off
Solid on
The modem router is connected to the internet successfully.
The modem router fails to connect to the internet.
A WPS connection is established.
The modem router is performing WPS negotiation.
The WPS feature is disabled, or the WPS feature is enabled but the modem router does not perform WPS negotiation.
The WiFi network is enabled.
WiFi LED indicator
LAN 1/2/3/4 LED indicator
Off
Solid on
Off
Solid on
The WiFi network is disabled.
The corresponding LAN port is connected properly.
The corresponding LAN port is disconnected, or not connected properly.
The DSL negotiation succeeds.
Blinking
Off
The modem router is performing DSL negotiation.
The port is disconnected, or not connected properly.
Buttons & ports
Port/jack
PWR
LAN1/2/3/4
DSL
Description
Power jack. Use the included power adapter to connect this jack to a power source for power supply.
LAN ports. Used to connect to wired devices, such as computers.
DSL port. Used to connect to a phone jack for internet access.
Button
WLAN/WPS
RST
ON/OFF
Description
Press and hold this button for less than 1 second to enable the WiFi network.
Press and hold this button for 1 to 3 seconds to enable the WPS feature.
Press and hold this button for about 6 seconds to disable the WiFi network.
Reset button. Hold down this button for about 6 seconds to restore factory settings. When all LED indicators turn off then light up, the modem router is reset successfully.
Power on/off button. Press this button to turn on/off the modem router.
I Connecting the modem router
1. Use a phone cable to connect the phone jack to the LINE port of the included ADSL splitter.
2. ( Optional ) If you do not use the phone service, skip this step. Use a phone cable to connect your phone to the PHONE port of the ADSL splitter.
3. Use a phone cable to connect the MODEM port of the ADSL splitter to the DSL port of the modem router.
4. Use the included power adapter to connect the modem router to a power source, and turn it on. The LED indicator blinks red slowly .
5. If you use a wireless device, such as a smart phone for setup, connect it to the WiFi network of the modem router using the default SSID labeled on the bottom of the modem router. By default, the WiFi password is not required.
If you use a wired device, such as a computer for setup, connect it to port LAN1, LAN2, LAN3 or LAN4 of the modem router.
II Configuring the modem router
1 Configuring your ADSL connection
Prerequisites
Before configuration, you need to get the following parameters from your internet service provider (ISP):
VPI and VCI values
Channel Mode (internet connection type)
PPPoE User Name and Password OR IPoE Local IP Address and related parameters (if any)
Your IP protocol type: IPv4 , IPv6 or IPv4/IPv6
Configuration procedure
1. Start a web browser on the device connected to the modem router, and visit 192.168.1.1
.
2. Enter the default User Name and Password , both are admin , and click Login .
*PPPoE is used to illustrate.
3. Choose Setup > WAN , and enter the VPI and VCI values provided by your ISP.
4. Select a Channel Mode (internet connection type), which is PPPoE in this example.
5. Select your IP Protocol type, which is IPv4 in this example.
6. Enter the PPPoE User Name and Password provided by your ISP.
7. Click Add to apply the settings.
2 Configuring your WiFi network
1. Choose Setup > WLAN > Basic , and customize your SSID (WiFi name).
2. Click Apply Changes .
3. Choose Setup > WLAN > Security , select an Encryption type, which is WPA2(AES) in this example, and specify a
Pre-Shared Key (WiFi password).
4. Click Apply Changes .
3 Accessing the internet
To access the internet with:
Wireless devices: Connect your wireless devices to the WiFi network of the modem router using the SSID and Pre-Shared
Key you set.
Wired devices: Connect your wired devices to the port LAN1, LAN2, LAN3, or LAN4 of the modem router.
FAQ
Q1: I cannot log in to the modem router’s web UI. What should I do?
A1: Try the following solutions:
If a wired device is used for setup:
Ensure that the Ethernet cable between the device and the modem router is connected properly.
Ensure that the device is set to Obtain an IP address automatically .
Clear cache of your browser, or replace one.
If a wireless device is used for setup:
Ensure that the device is connected to the WiFi network of the modem router.
Ensure that the mobile data (if any) of the device is disabled.
Ensure that the login IP address (192.168.1.1) you entered is correct.
If the problem persists:
Hold down the RST button for about 6 seconds to restore to factory settings, and configure it again.
Q2: I cannot access the internet after completing the configuration, what should I do?
A2: Try the following solutions:
Check if the LED indicator blinks green slowly . If so , check if the DSL port is properly connected to the phone jack.
Check if the LED indicator lights solid green . If not, check if the parameters you entered for internet access are correct.
Check if your computers are set to Obtain an IP address automatically .
If the problem persists, contact your ISP for help.
Q3: I forget my WiFi password, what should I do?
A3: Try the following solutions:
Log in to the web UI of the modem router, and change it on the Setup > WLAN > Security part.
If you forget the login password of the web UI as well, reset the modem router. The default login user name and password are both admin .
Q4: How to reset the modem router?
A4: When the LED indicator lights up and does not blink red slowly , hold down the RST button for about 6 seconds. When all
LED indicators turn off then light up, the modem router is reset successfully.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This equipment should be installed and operated with minimum distance 20cm between the device and your body.
NOTE : (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type D301V4 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.tendacn.com/en/service/download-cata-101.html
Operating Frequency: 2412 - 2472 MHz
EIRP Power (Max.): 19.5dBm
Software Version:
Caution:
Adapter Model: BN049-A05009E , BN049-A05009B
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100 - 240V AC 50/60Hz 0.3A
Output: 9V 600mA
: DC Voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Operating Temperature: 0°C - 40°C
Operating Humidity: (10% - 90%) RH, non-condensing
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
USA hotline: 1-800-570-5892
Toll Free: Daily-9am to 6pm EST
Canada hotline: 1-888-998-8966
Toll Free: Mon - Fri 9 am - 6 pm PST
Hong Kong hotline: 00852-81931998
Global hotline: +86 755-2765 7180 (China Time Zone)
Website: http://www.tendacn.com
E-mail: [email protected]
Copyright
© 2019 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice.
