U S
U K
DE ic di ic , ig
C
J a t
. F ( ue d Jan 13) to ph a i a b u e to h
, tu
1
N 1 0
The team at Drive Medical develops its products to give our customers the freedom to live independently. This encompasses their daily home life and provides them with the opportunity to enjoy an outing with family and friends. Our goal is to develop a range that will provide individuals with a chance to enjoy every day life.
Scout Scooter
Owner’s Handbook
QUICK REFERENCE GUIDE
Problem: Scooter will not switch on
Symptoms: Remedy:
Batteries not connected
Circuit breaker has tripped
Check batteries connected
Push circuit breaker to reset
Rear and front sections not connected
Check connection on frontto-rear loom
Problem: Scooter will switch on but will not run
Symptoms:
Flat batteries
Charger plugged in
Motor in freewheel mode
Problem: Scooter appears slow
Symptoms:
Flat batteries
Speed setting slow
Remedy:
Recharge battery
Unplug charger from scooter
Push down freewheel lever
Remedy:
Recharge battery
Turn up speed dial
Problem: Seat moves whilst in use
Symptoms:
Seat not locked in position
Remedy:
Slowly rotate the seat until it drops in place and is secure.
Problem: Tiller appears loose or will not swivel freely
Symptoms:
Tiller adjustment knob loose
Tiller Lock Applied
Remedy:
Tighten tiller adjustment knob
Release Tiller Lock
Problem: Horn sounds involuntarily / automatically
Symptoms: Remedy:
The scooter has diagnosed a fault
Ensure the wigwag paddle is released and switch the scooter off and on.
Recharge batteries if error persists.
“Caution: Federal Law restricts this device to sale by or on the order of a practitioner licenced by the law of the
State in which he/she practices”
(USA Only)
Scout Electric Scooter Page 1 of 14
CONTENTS
1.
PREFACE
2.
SAFETY NOTICE
2.1
Before Driving
2.2
Whilst Driving
2.3
Labelling
2.4
Electromagnetic Interference
3. PARTS INTRODUCTION
4. OPERATION
4.1 Control Panel
4.2 How to Operate Your Scooter
5. DRIVING ON THE ROAD
6. BATTERY CHARGING AND CARE
7. INSPECTION AND MAINTENANCE
7.1 Daily Checking
7.2 Service Record
7.3 Battery Pack and Tyres
7.4 Cleaning
7.5 Storage
7.6 Moving About
7.7 Disassembling the Scooter for
Transportation
7.8 Assembling the Scooter
8. TROUBLESHOOTING
9. SPECIFICATION
10. WARRANTY
11. APPENDIX: SERVICE RECORD
Owner’s Handbook (Code: MS008_IFU 01/13)
9
15
16
19
3
4
24
25
26
1.
PREFACE AND INTRODUCTION
Please carefully read this owner’s handbook before using the scooter to ensure that you operate the scooter safely. Improper use of the scooter could result in damage, injury or traffic accidents.
This handbook also advises how to get most out of your scooter by giving comprehensive operating, assembly and maintenance instructions for the scooter.
A repair and maintenance record chart and warranty information is included with this handbook. Please keep it in a safe place or with the scooter.
If someone else uses the scooter make sure that you provide him or her with this handbook for their consideration.
Scout Electric Scooter
As designs change some of the illustrations and pictures in the manual may not correspond to the scooters that you purchased. We reserve the right to make design modifications.
The Scout range of scooters have been designed and manufactured to provide a comfortable and secure yet affordable solution for some mobility requirements. They are manoeuvrable and are suitable for indoor and some outdoor application where the terrain is forgiving (for example smooth paths, shopping centres, etc). They are class 2 scooters as defined by the Road Traffic Act 1988.
They feature a rotating seat and can be easily folded and disassembled.
There are two models available:
3-wheel model for compact environments
4-wheel model for greater stability
Page 2 of 14
2.
SAFETY
2.1 Before Driving
The user needs to be familiar with the use and operation of this scooter before driving.
Ride on the pavement and pedestrian areas only.
Never ride on motorways or dual carriageways.
Only use roads to cross to other side of the pavement.
Be aware of traffic when crossing or using roads.
Use extreme caution when driving your scooter in busy areas such as shopping malls.
Do not drive the scooter under the influence of drink or drugs, or when you are tired.
Be careful when using the scooter in low light. It has not been design for use at night.
Before using the scooter in busy or hazardous environments, familiarise yourself with the operation of the scooter. Practice in an open and safe area which is free from hazards and other people. Turn the speed dial down for your initial practice.
2.2
Whilst Driving
Do not use your scooter on surfaces that are muddy, gravelly, bumpy, narrow, snowed over, icy; or on towpaths near to canals which are not guarded.
Do not use your scooter outside when it is raining, snowing, misty or windy.
Do not make erratic turnings on your scooter.
Bear in mind driving motions such as accelerating, stopping, turning, reversing, and the effect of gradients.
Owner’s Handbook (Code: MS008_IFU 01/13)
Slow down when driving on gradients. Always lean forward when climbing a steep gradient. Do not travel on gradients exceeding those stated on the diagram below:
Do not drive on roads with large drops or potholes.
The scooter is not suitable for carrying passengers.
Do not use the scooter to carry heavy goods.
Do not use a mobile phone or other wireless communication devices whilst driving. Always stop somewhere suitable and switch off the scooter before using the phone.
Do not set in freewheel mode when driving, especially on a gradient. Ensure that the scooter’s automatic brake is applied before use.
Do not exceed the weight limit of the scooter.
2.3
Labelling
Please carefully read all labels applied to the scooter before driving. For future reference, do not remove them from the scooter. The labels are also shown below:
NEVER LIFT SCOOTER UP BY THE
REAR OR FRONT OF SHROUD
Above: Located on rear shroud
!
WARNING
Never operate the freewheel lever while seated on the scooter or on an incline!
OPERATION OF THE FREEWHEEL LEVER
Always pull UP FIRMLY for freewheel mode
Always push DOWN FIRMLY for drive mode
Above: Located by freewheel lever on rear
WARNING:
EMI
REFER TO
OPERATORS
MANUAL FOR
INFORMATION
Above: Located on rear
REF
S/No
MS008PB
Drive Medical Ltd (HX5 9JP)
Drive Medical GmbH (D-88316)
Maximum User Mass 130kg
WARNING:
EMI
REFER TO
OPERATORS
MANUAL FOR
INFORMATION
THIS UNIT HAS
ACHIEVED 20 V/m
EMI TESTING
Above: Located on rear
5 0 6 0 2 6 6 8 4 8 7 1 1
MADE IN
VIETNAM
WARNING
Please hold the tiller before loosen the tiller adjustment knob.
Before lifting or driving the scooter make certain the tiller adjustment knob is fully tightened.
Never attempt to adjust the tiller whilst the scooter is in motion
Above: Located on tiller
2.4
Electromagnetic Interference
Scooters may be susceptible to electromagnetic interference (EMI) from sources such as mobile phones, walkie-talkies, TV and radio broadcast stations and amateur radio sets. In some cases, there is a risk this interference may cause involuntary movement of the scooter. The scooter has been tested and passed to withstand interference to a level of 20V per metre.
Be aware that the above sources may cause involuntary movement due to EMI. Exercise caution whilst using the aforementioned devices and avoid close proximity to TV and Radio broadcast stations.
The addition of components or accessories may effect the EMI susceptibility of the scooter. Do not fit accessories other than Drive Medical authorised accessories.
Scout Electric Scooter Page 3 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
3.
PARTS INTRODUCTION
CONTROL
PANEL
Scout 4-wheel pictured below
SEAT
SEAT
POST
TILLER ADJ.
KNOB
CHARGER
SOCKET
BATTERY
PACK
Rear section shown below (applicable to both models)
TILLER
LOCK
4.
OPERATION
4.1 Control Panel
SPEED
DIAL
WIGWAG
PADDLE
FREE-
WHEEL
LEVER
ANTI TIP
WHEEL
BATTERY
GAUGE
HORN
BUTTON
4.2
How To Operate Your Scooter
Key Ignition. The key ignition acts as the power switch for the scooter. To switch the power on, turn the key clockwise and battery gauge should illuminate. To switch the power off, turn the key anticlockwise, after which the battery gauge should switch off and the key can be removed.
Do not turn the ignition off whilst driving as this will lead to an emergency stop and possible risk of damage or injury.
Speed Dial. Turn the speed dial to determine the maximum speed of the scooter. Turn the dial clockwise to increase the speed setting and turn the dial anticlockwise to decrease the speed setting.
Do not adjust the speed dial whilst driving as this could result in loss of control. Do not set the highest speed whilst driving indoors.
Tiller Lock. When the tiller is centred, pull the tiller lock down to secure the tiller for transportation.
Push the tiller lock up to release.
Always ensure the tiller lock is disengaged when driving the scooter. Always check the tiller moves freely before driving.
Moving and Braking. To move forward, pull the right hand side of the wigwag paddle with your hand towards you whilst resting the palm of your hand on the lower handle bar. Pull the left hand side of the wigwag paddle towards you and the scooter will move backwards, emitting an audible reversing alarm. To brake, release the wigwag paddle which will return to neutral and activate the electromagnetic brake automatically which will bring the scooter to a prompt stop. The wigwag paddle allows you to control the speed of the scooter up to a maximum speed determined by the
Speed Dial. The further the wigwag paddle is deflected, the faster the scooter will go (up to
4mph).
Scout Electric Scooter Page 4 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
Warning
Do not push both left and right hand sides of the wigwag simultaneously. You will not be able to control the scooter.
Horn Button. Press the horn button to sound the horn, Release the button to stop the horn. The horn is the yellow button located on the control panel.
Braking – Electromagnetic Brake. Release the wigwag paddle completely, and the electromagnetic brake will be activated automatically and the scooter will stop.
When on a gradient, never set the vehicle to freewheel mode. The brakes will not be applied.
Seat. The seat can be rotated and locked in position at 45º intervals. Push the seat lever forward and swivel the seat. Release the lever and then continue swivelling the seat until it locks in position.
Attention.
Return the seat to the forward position before driving.
Adjusting the Seat Height.
Remove the seat from your scooter then remove the locking pin (arrowed). Move the chrome seat post to the desired height.
Adjust the seat post height so that there is a predrilled hole to reinsert the locking pin. Insert the locking pin and lock.
Battery Gauge. The battery gauge on the tiller console lights LEDs to show remaining power:
Green (3 or 4 LEDS lit) - 40% - 100% capacity
Yellow (2 LEDs lit) - draining charge (10% - 30%)
Red (1 LED lit) - immediate recharge is necessary.
The remaining power indicated by the battery gauge will vary by the driving time incurred and how you drive. Repeated starting, stopping and climbing will consume power more quickly. The gauge is shown previously.
If the leftmost LED is flashing, this means the scooter has encountered a problem. The LED will flash a number of times then pause. Count the number of flashes to determine the problem.
If you experience any flash sequences first restart the scooter, ensuring the wigwag paddle is released. If this does not remedy the problem recharge the batteries.
If the error persists contact your Drive Medical Dealer.
Attention
You should recharge the batteries after each use to ensure maximum range. Read the Battery Charging section in the handbook before use.
Circuit Breaker (
Arrowed Below)
. The circuit breaker may trip when the scooter is under excessive load or when travelling on steep inclines.
It will be more prone to tripping when the scooter is low on battery charge. Under normal conditions the circuit breaker button will protrude by 2mm – 3mm.
If the circuit breaker has tripped the button will protrude by 7mm. To reset the circuit breaker, push the button in and the scooter should operate as normal.
Scout Electric Scooter Page 5 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
Freewheel Lever
Engaged (Drive) Mode:
Push the lever down completely and the scooter can be driven by the motor.
Freewheel Mode:
Pull the lever up and switch the scooter off.
The scooter can now be pushed / moved manually.
Warning
The lever should only be set to
FREEWHEEL when on flat ground and unoccupied by the user. Otherwise, there is a risk of damage or injury.
Tiller Adjustment
The tiller can be adjusted in to many different positions to suit each user. To adjust follow the steps below:
1.
Loosen the knob (as shown below in the photo) so the tiller can move.
2.
Using the other hand, reposition the tiller as required then retighten the knob to secure.
Scout Electric Scooter Page 6 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
5.
DRIVING ON THE ROAD
Starting and Driving
1.
Make sure the seat is installed properly.
2.
Make sure the tiller has been secured properly and the tiller lock is disengaged.
3.
Fold down the armrests so you can rest your arms on them.
4.
Switch the key ignition on.
5.
Check the battery gauge to see whether there is enough power for your journey. If you have any doubt about the remaining power, recharge the battery pack before use.
6.
Set the speed dial to a position you feel safe and comfortable with.
7.
Check the wigwag paddle and automatic brake work correctly.
8.
Before driving, check the environment around you is safe for you to drive.
Warning
Be careful whilst driving in heavy traffic or crowded areas. Whilst reversing the vehicle, be aware of people or objects behind you.
Stopping
1.
Release the wigwag paddle completely. The vehicle will automatically brake and stop.
2.
Switch the scooter off at the key ignition and pull out the key.
Stopping distance will vary with speed so begin braking as early as possible.
Always park on flat ground, switch off and remove the key before dismounting.
6.
BATTERY CHARGING AND CARE
The battery pack can be charged either when it is installed or removed from the scooter.
To Charge
1.
Switch the key ignition off.
2.
Plug the charger’s power cord in to the mains.
3.
If required, remove the battery pack (see next section for details)
4.
Open the charging socket cap on the battery pack. Then connect the charger’s round plug in to the charging socket (as shown in photo)
5.
Switch on the plug socket at the mains.
To Remove the Battery Pack
1.
Switch the key ignition off.
2.
Lift out of the scooter using the handle on the battery pack.
To Install The Battery Pack
Lower the battery pack in to the scooter.
Use the locking lever to secure the battery pack.
Scout Electric Scooter Page 7 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
Charger Light
The charger light will illuminate orange to indicate the batteries are charging. The charging duration is about 8 hours, however to a 12 hour charge is recommended for optimum performance. The orange light will turn green when charging is complete.
Ensure that the charger is removed from the mains and the scooter or battery pack after charging. Failure to do this may flatten the battery.
Do not remove the battery pack whilst the scooter is switched on.
Suggestions
1.
Do not disconnect the charger cord until charging is completed and the light is lit
Green.
2.
When fully charged the battery charger will still trickle charge the battery for optimum range.
3.
Even when not in use, the scooter should be charged at least every week to ensure battery longevity.
4.
Ambient temperature will effect charging time. Charging time will be longer in cold environments.
5.
The batteries carry a 1 year warranty which covers manufacturing defects only. It does not cover battery faults as result of not following the guidelines herein.
Warning
1.
Only use the charger supplied with the scooter. Using the wrong type of charger may cause damage. Never disassemble or modify the scooter.
2.
Always charge the scooter in a well ventilated space. Avoid direct sunlight or contact with water and moisture.
3.
Do not charge or operate the scooter in temperatures below -10ºC or above
50ºC. Do not expose the battery pack to these temperatures.
About the Battery Pack
The battery pack contains two 12V 12ah batteries.
The batteries are sealed lead acid type and are maintenance free and are non-spillable. They are fitted with spade terminals.
The batteries require charging every week to ensure battery longevity.
The batteries supplied as standard with the battery pack are classified as safe for air transport under
IATA special provision A67.
Warning
If battery pack loses contact with the scooter during operation switch the key ignition off, re-insert the battery pack and switch the ignition back on.
Battery Care
1.
You should recharge the batteries after each time the scooter is used to ensure maximum battery range. The batteries should be charged at least once a week even if the scooter is not used.
2.
After charging or replacing a new battery, drive the scooter for a short period to ensure battery capacity is sufficient.
3.
In cold environments, the battery may respond more slowly and range will be reduced.
4.
When driving on a gradient, the battery gauge will fluctuate. This is a normal occurrence.
5.
Battery range is reduced when driving up gradients or on rough terrain, as the scooter uses more power.
6.
The batteries should not be charged for more than 24 hours.
Battery Replacement
It is natural for the battery capacity to reduce with time, even if the battery is charged as directed above.
When the battery range is about half of its peak performance we recommend that the batteries are changed. Continuing to use an old battery will result in a rapid reduction in the range of the scooter and can cause excessive wear and tear on other parts of the scooter.
Scout Electric Scooter Page 8 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
7.
INSPECTION AND MAINTENANCE
7.1
Weekly Checking
Check the following items weekly or before driving. If you find anything abnormal contact your Drive Medical
Dealer for further inspection or advice.
Tiller. Ensure it is not loose and can turn smoothly
Speed control dial. Ensure it adjusts freely.
Wigwag paddle. Ensure scooter moves when lever is pressed, and stops when lever released.
Motor. Check for any abnormal noise and electromagnetic brakes work correctly.
Freewheel Lever. Ensure it works correctly.
Seat. Ensure is swivels and locks easily.
Tyres. Check tyre tread depth and for any signs of damage such as cracking.
7.2
Service Record
To ensure your scooter is correctly serviced take it to your Drive Medical dealer for regular servicing. We recommend that scooters are serviced at least annually, and your dealer may charge a fee for this.
A copy of the service record is at the back of this handbook.
Even if the scooter has not been used, it should still be serviced annually.
7.3
Battery Pack and Tyres
For information on the battery pack, please read section 6 on Battery Charging and Care.
Tyre condition will be affected by how you drive the scooter and what terrain it is driven on.
The Scout comes with solid tyres which are puncture proof, so there is no need to check tyre pressure.
7.4
Cleaning
The scooter should be cleaned periodically, especially if you tend to drive on sand, gravel or in other adverse environments.
Use a soft, wrung dry cloth to keep your scooter clean and dust free. Use a damp cloth and mild detergent to clean the scooter.
Warning
Do not use a hose pipe or splash water directly on to the scooter.
7.5
Storage
Do not use petrol, solvents or vaporising solutions as these many damage body panels. Do not use wax
Ensure the charger is unplugged and the scooter switched off before cleaning the scooter.
Ensure the scooter is stored with the seat set in the forward position, the scooter switched off with the battery pack removed and charger disconnected.
Store the scooter in environments which are free from direct sunlight and water or moisture.
7.6
Moving About
1.
Switch off the scooter using the ignition key and dismount from the scooter.
2.
Lift the scooter by the chassis only.
3.
For your safety ask for help if required. You will need two or more people when moving or lifting the scooter as a whole.
Never lift the scooter by the bumpers or body panels, as this can cause injury or damage.
Scout Electric Scooter Page 9 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
7.7
Disassembling the Scooter
Both the models of scooter can be disassembled in to four pieces without tools: seat, front section, rear section and battery pack
The procedure for disassembly is the same for both scooters. Please perform the following steps:
1.
Push the Seat
Rotate Lever whilst pulling up on the seat to remove.
2.
Turn the handle to release the battery pack, then lift out the battery pack from the main body of the scooter.
3.
Turn the tiller anticlockwise to loosen tiller. Lower the tiller and then turn the tiller knob clockwise to secure.
4.
Lock front tiller by pulling the locking knob out and turning 90º.
5.
Pull up on the
Connecting Handle to split the two halves of the base.
Scout Electric Scooter Page 10 of 14
7.8
Assembling the Scooter
1.
Line up the two sections of base.
Lift up the handle and use the handle to slowly lower the two parts so they lock together.
2.
Unlock front tiller by pulling the locking knob out and turning
90º.
3.
Loosen the tiller adjustment knob and pull up the tiller to the required height.
Retighten the knob to secure.
4.
Lower battery pack in to the compartment in the scooter and then turn the handle to secure the pack in place.
5.
Replace the seat and rotate it until it locks in to its correct position.
After assembling the Scout, make sure the tiller adjustment knob is fully tightened.
The weights of the major component parts for the 4wheel Scout are below:
Seat – 7.2kg (15.9lb)
Front Section - 15.8kg (34.7lb)
Rear Section – 10.7kg (23.5lb)
Battery Pack – 9.2kg (20.2lb)
Owner’s Handbook (Code: MS008_IFU 01/13)
8.
TROUBLESHOOTING
The troubleshooting guide is also featured on page
1 of the Owner’s Handbook.
Problem: Scooter will not switch on
Symptoms: Remedy:
Batteries not connected
Circuit breaker has tripped
Check batteries connected
Push circuit breaker to reset
Rear and front sections not connected
Check connection on frontto-rear loom
Problem: Scooter will switch on but will not run
Symptoms: Remedy:
Flat batteries
Charger plugged in
Motor in freewheel mode
Recharge battery
Unplug charger from scooter
Push down freewheel lever
Problem: Scooter appears slow
Symptoms:
Flat batteries
Speed setting slow
Remedy:
Recharge battery
Turn up speed dial
Problem: Seat moves whilst in use
Symptoms:
Seat not locked in position
Remedy:
Slowly rotate the seat until it drops in place and is secure.
Problem: Tiller appears loose or will not swivel freely
Symptoms:
Tiller adjustment knob loose
Tiller Lock Applied
Remedy:
Tighten tiller adjustment knob
Release Tiller Lock
Problem: Horn sounds involuntarily / automatically
Symptoms: Remedy:
The scooter has diagnosed a fault
Ensure the wigwag paddle is released and switch the scooter off and on.
Recharge batteries if error persists.
Scout Electric Scooter Page 11 of 14
9.
SPECIFICATION
Model Reference
Dimension
(L x W x H)
Total Weight
(see below for weights of component parts)
Scout 4-wheel
108cm x 48cm x 91cm
42.5” x 19” x 36”
42.8kg / 94lb
Propulsion motor
Battery
Charger
270W / 0.36hp
12V 12Ah x 2
24V 1.8A
Front Tyre
Rear Tyre
200 x 50 solid
200 x 50 solid
Top Speed (Forward) 6.4kph / 4.0mph
Reverse 4.0kph / 2.5mph
Climbing angle
Maximum Cruising range
(see note)
Up to 8
13 - 16km / 8 - 10 miles
Min. turning radius
Ground clearance
Kerb climbing ability
Obstacle climbing ability
Max. load weight
(including goods)
140mm / 55”
6cm / 2.5”
5cm / 2”
5cm / 2”
130kg / 20 stone
Remark: The manufacturer reserves the right to modify the specification if necessary. The final specification is subject to the individual scooter you purchase from your dealer.
Note:
Maximum driving distance is based on an ambient temperature of 20 ºC, a 75kg driver and a brand new fully charged battery by a constant driving speed at 6 km/h with 70% battery power discharged.
The scooter is classed as a type A vehicle as defined by EN 12184.
Weights of Component Parts
•
•
•
•
The weights of the major component parts for the
Scout are below:
Seat – 7.2kg (15.9lb)
Front Section (4-wheel) - 15.8kg (34.7lb)
Rear Section – 10.7kg (23.5lb)
Battery Pack – 9.2kg (20.2lb)
Owner’s Handbook (Code: MS008_IFU 01/13)
10.
VIN NUMBER
To ensure the correct after sales service and warranty service support, please write down the scooter serial number. The serial number is located on the back righthand side of the frame.
VIN Number
Motor S/No.
Controller S/No.
Also, note your Drive Medical dealer below:
Dealer
Address
Postcode
Telephone
11.
WARRANTY
There is a comprehensive one-year warranty from the date on which your new scooter is delivered. The warranty covers the scooter for repairs or replacement during this period. For more detail, please see the
Warranty Conditions below.
Warranty Conditions:
1.
Any work or replacement part installation must be carried out by an authorized Drive Medical dealer
/ service agent.
2.
To apply the warranty should your scooter require attention please contact the designated service agent listed above.
Scout Electric Scooter
3.
Should any part of the scooter require repair or full or part replacement, as a result of a manufacturing or material defect within twelve months of receiving the scooter, replacement parts will be supplied free of charge.
Note: This guarantee is not transferable
4.
Any repaired or replaced parts will be covered by this warranty for the balance of the warranty period on the scooter.
5.
Consumable items supplied will not generally be covered during the normal warranty period unless such items require repair or replacement clearly as a direct result of a manufacturing or material defect.
Such items include (among others): upholstery, tyres and batteries.
6.
The above warranty conditions apply to brand new scooter purchased at the full retail price. If you are unsure whether your scooter is covered, check with the service agent.
7.
Under normal circumstances, no responsibility will be accepted where the scooter has failed as a direct result of: a) The scooter or part not having been maintained in accordance with the manufacturer’s recommendations. b) Failure to use the manufacturer’s specified parts c) The scooter or part having been damaged due to neglect, accident or improper use d) The scooter or part having been altered from the manufacturer’s specifications or repairs having been attempted before the service agent is notified
Please note your local service agent’s contact details in the previous box. In the event of your scooter requiring attention, contact them and give all relevant details so they can act quickly.
The manufacturer reserves the right to alter without notice any weights, measurements or other technical data shown in this manual. All figures, measurements and capacities shown in this manual are approximate and do not constitute specifications.
Page 12 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
Appendix A: Service Record
YEAR
Service Dates
1 2 3 4 5 YEAR
Service Dates
Controller
On/off switch
Control Lever
Braking
Recharge point
Batteries
Upholstery
Seat
Back
Armrests
Electrics
Connections condition
Lights
Test run
Forwards
Reverse
Levels
Connections
Discharge test
Wheels and
Tyres
Wear
Pressure
Bearings
Wheel nuts
Motors
Wiring
Noise
Connections
Brake
Brushes
Chassis
Condition
Steering
Scout Electric Scooter Page 13 of 14
Emergency stop
Left turn
Right turn
Slope test
Over obstacles
List Items repaired
1 2 3 4 5
Owner’s Handbook (Code: MS008_IFU 01/13)
Notes:
Scout Electric Scooter Page 14 of 14
Owner’s Handbook (Code: MS008_IFU 01/13)
