Psion Teklogix netpad Quick Start Guide
Below you will find brief information for netpad 1000 Series, netpad 3000 Series. This guide provides a quick introduction to the Psion Teklogix netpad, a Windows CE.Net OS-based mobile tablet computer. It covers essential aspects like fitting the antenna, power management, using the stylus, screen controls, and basic operations such as turning the device on/off, resetting, and scanning bar codes. The guide helps users to initiate and use the netpad.
Advertisement
Advertisement
netpad
Win CE 4.0
Quick Start Guide
February 5, 2003 P/N A6122 0009 0003.A
ISO 9001 Certified
Quality Management System
© Copyright 2003 by Psion Teklogix Inc., Mississauga, Ontario
This document and the information it contains is the property of Psion
Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Psion Teklogix manufactured goods and services. Furthermore, this document is not to be used as a basis for design, manufacture, or sub-contract, or in any manner detrimental to the interests of Psion Teklogix Inc.
All trademarks are the property of their respective holders.
Return-To-Factory Warranty
Psion Teklogix warrants a return-to-factory warranty for a period of one year.
In some regions, the warranty exceeds this period. Please contact your local
Psion Teklogix office for details. For a list of offices, see “Worldwide
Offices” on page 44. The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been tampered with, altered, or repaired by any person other than an employee of an authorized Psion Teklogix service organization. See Psion Teklogix terms and conditions of sale for full details.
Service
When requesting service, please provide information concerning the nature of the failure and the manner in which the equipment was used when the failure occurred. Type, model, and serial number should also be provided.
Before returning any products to Psion Teklogix, please call the Customer
Services Group for a Return Authorization number.
Support Services
Psion Teklogix provides a complete range of product support services to its customers. For detailed information, please refer to “Support Services And
Worldwide Offices” on page 43.
Disclaimer
Every effort has been made to make this material complete, accurate, and upto-date. Psion Teklogix Inc. reserves the right to make changes without notice and shall not be responsible for any damages, including but not limited to consequential damages, caused by reliance on the material presented, including but not limited to typographical errors.
Table Of Contents
Approvals And Safety Summary . . . . . . . . . . . . . . . . . . . . . . . 3
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 Applications Installed On The netpad . . . . . . . . . . . . . 15
1.1.1 About ActiveSync . . . . . . . . . . . . . . . . . . . . . . . 15
1.2 Caring For The netpad . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.3 Additional Programs And Third Party Applications . . 19
2. Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1 Features Of The netpad . . . . . . . . . . . . . . . . . . . . . . . . 19
2.2 Preparing The netpad For Use . . . . . . . . . . . . . . . . . . . 21
2.2.1 Fitting The Antenna . . . . . . . . . . . . . . . . . . . . . . 21
2.2.2 Use Of The Soft Belt Holster . . . . . . . . . . . . . . . 22
2.2.3 Power Management . . . . . . . . . . . . . . . . . . . . . . 23
2.2.4 Multimedia Cards. . . . . . . . . . . . . . . . . . . . . . . . 26
2.2.5 Installing And Removing The SIM Card . . . . . . 27
2.3 Turning On And Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.4 Finding And Using The Stylus . . . . . . . . . . . . . . . . . . . 31
2.5 The Screen, Command Icons, And Toolbar . . . . . . . . . 32
2.6 How To Reset The netpad . . . . . . . . . . . . . . . . . . . . . . 33
2.7 The Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.8 First Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.8.1 Navigating Between Files And Folders . . . . . . . 36
2.8.2 Starting Programs . . . . . . . . . . . . . . . . . . . . . . . . 36
2.8.3 Programs And Files . . . . . . . . . . . . . . . . . . . . . . 37
2.8.4 Entering Information . . . . . . . . . . . . . . . . . . . . . 37
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 1
2.8.5 Using Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.8.6 Using Dialogues . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.8.7 Copying Information Between Programs . . . . . . 40
3. The netpad Docking Station . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.1 Using The Docking Station . . . . . . . . . . . . . . . . . . . . . 41
3.2 Communications Settings . . . . . . . . . . . . . . . . . . . . . . . 42
4. Support Services And Worldwide Offices. . . . . . . . . . . . . . . 43
4.1 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.2 Product Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3 Worldwide Offices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4 Worldwide Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Approvals And Safety Summary
Product:
CE Declaration Of Conformity
netpad 1000 Series with Serial Docking Station
Application of Council Directives: EMC Directive: 89/336/EEC
Low Voltage Directive: 73/23/EEC
Conformity Declared to Standards: EN 55022: 1998; Class B;
EN 55024: 1998;
EN 61000-4-2; ±4kV CD; ±8kV AD
EN 61000-4-3; 3V/m, 80-1000 MHz, 900 MHz
EN 61000-4-4; ±1kV Power lines
EN 61000-4-5; ±2kV Common;
EN 61000-4-6; 3V
±1kV Differential mode
RMS
, 150 kHz-80 MHz
EN 61000-4-11; AC Mains Ports
EN 61000-3-2; EN 61000-3-3
EN 60950: 1992 + A1 + A2 + A3 + A4 + A11
Manufacturer: PSION TEKLOGIX INC.
2100 Meadowvale Blvd.
Mississauga, Ontario; Canada L5N 7J9
2002 Year of Manufacture:
Manufacturer’s Address in the
European Community:
Type of Equipment:
Equipment Class:
PSION TEKLOGIX S.A.
La Duranne; 135 Rue Rene Descartes
BP 421000
13591 Aix-En-Provence
Cedex 3; France
Information Technology Equipment
Commercial and Light Industrial
Manufacturer: Psion Teklogix Inc. Ontario
Legal Representative in Europe: Psion Teklogix S.A. France
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 3
4
Product:
CE Declaration Of Conformity
netpad 3000 Series with Serial Docking Station
Application of Council Directives: EMC Directive: 89/336/EEC
Low Voltage Directive: 73/23/EEC
Conformity Declared to Standards: EN 55022: 1998; Class B;
EN 55024: 1998;
EN 61000-4-2; ±4kV CD; ±8kV AD
EN 61000-4-3; 3V/m, 80-1000 MHz, 900 MHz
EN 61000-4-4; ±1kV Power lines
EN 61000-4-5; ±2kV Common;
EN 61000-4-6; 3V
±1kV Differential mode
RMS
, 150 kHz-80 MHz
EN 61000-4-11; AC Mains Ports
EN 61000-3-2; EN 61000-3-3
EN 60950: 1992 + A1 + A2 + A3 + A4 + A11
EN 60825-1, AM.2: 2001; Laser Safety
Manufacturer: PSION TEKLOGIX INC.
2100 Meadowvale Blvd.
Mississauga, Ontario; Canada L5N 7J9
2002 Year of Manufacture:
Manufacturer’s Address in the
European Community:
Type of Equipment:
Equipment Class:
PSION TEKLOGIX S.A.
La Duranne; 135 Rue Rene Descartes
BP 421000
13591 Aix-En-Provence
Cedex 3; France
Information Technology Equipment
Commercial and Light Industrial
Manufacturer: Psion Teklogix Inc. Ontario
Legal Representative in Europe: Psion Teklogix S.A. France
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
FCC Information For The USA
FCC Declaration Of Conformity (DoC)
Applicant’s Name & Address: PSION TEKLOGIX INC.
2100 Meadowvale Blvd.
Mississauga, Ontario, Canada L5N 7J9
Tel.: (905) 813-9900
US Representative’s
Name & Address: Psion Teklogix Corp.
1810 Airport Exchange Blvd., Suite 500
Erlanger, Kentucky, 41018, USA
Tel.: (859) 371-6006
Equipment Type / Environment: Computing Devices for Home and Office Use
Trade Name / Model No.: netpad
Year of Manufacture:
Applicant:
Legal Representative in US:
2002
Standard(s) to which Conformity is Declared:
The netpad and Serial Docking Station , supplied by Psion Teklogix, has been tested and found to comply with FCC PART 15, SUBPART B - UNINTENTIONAL RADI-
ATORS, CLASS B COMPUTING DEVICES FOR HOME & OFFICE USE .
Psion Teklogix Inc.
Mississauga, Ontario, Canada
Psion Teklogix Corp.
Erlanger, Kentucky, USA
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 5
6
CE Marking
When used in a residential, commercial or light industrial environment the product and its approved UK and European peripherals fulfill all requirements for CE marking.
R&TTE Directive 1999/5/EC
This equipment complies with the essential requirements of EU Directive 1999/5/EC (Declaration available: www.psionteklogix.com).
Cet équipement est conforme aux principales caractéristiques définies dans la Directive européenne RTTE 1999/5/CE. (Déclaration disponible sur le site: www.psionteklogix.com).
Die Geräte erfüllen die grundlegenden Anforderungen der RTTE-
Richtlinie (1999/5/EG). (Den Wortlaut der Richtlinie finden Sie unter: www.psionteklogix.com).
Questa apparecchiatura è conforme ai requisiti essenziali della Direttiva Europea R&TTE 1999/5/CE. (Dichiarazione disponibile sul sito: www.psionteklogix.com).
Este equipo cumple los requisitos principales de la Directiva
1995/5/CE de la UE, “Equipos de Terminales de Radio y Telecomunicaciones”. (Declaración disponible en: www.psionteklogix.com).
Este equipamento cumpre os requisitos essenciais da Directiva
1999/5/CE do Parlamento Europeu e do Conselho (Directiva RTT).
(Declaração disponível no endereço: www.psionteklogix.com).
Ο εξοπλισ µ ός αυτός πληροί τις βασικές απαιτήσεις της κοινοτικής
οδηγίας EU R&TTE 1999/5/E Κ . ( Η δήλωση συ µµ όρφωσης
διατίθεται στη διεύθυνση : www.psionteklogix.com)
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Deze apparatuur voldoet aan de noodzakelijke vereisten van EUrichtlijn betreffende radioapparatuur en telecommunicatie-eindapparatuur 199/5/EG. (verklaring beschikbaar: www.psionteklogix.com).
Dette udstyr opfylder de Væsentlige krav i EU's direktiv 1999/5/EC om Radio- og teleterminaludstyr. (Erklæring findes på: www.psionteklogix.com).
Dette utstyret er i overensstemmelse med hovedkravene i R&TTEdirektivet (1999/5/EC) fra EU. (Erklæring finnes på: www.psionteklogix.com).
Utrustningen uppfyller kraven för EU-direktivet 1999/5/EC om ansluten teleutrustning och ömsesidigt erkännande av utrustningens
överensstämmelse (R&TTE). (Förklaringen finns att läsa på: www.psionteklogix.com).
Tämä laite vastaa EU:n radio- ja telepäätelaitedirektiivin
(EU R&TTE Directive 1999/5/EC) vaatimuksia. (Julkilausuma
L nähtävillä osoitteessa: www.psionteklogix.com).
Use of the 802.11 netpad in France:
Owing to French Government restrictions, the French 802.11 netpad is limited to indoor use. They may be used outdoors, on private property, only with prior authorization from the French
Ministry of Defense.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 7
8
FCC Information To The User
Radio And Television Interference
This equipment radiates radio frequency energy and if not used properly—that is, in strict accordance with the instructions in this manual—may cause interference to radio communications and television reception. It has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC
Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation distance between the equipment and the receiver.
• If you are using the equipment with a mains adaptor, plug it into an outlet which is on a different circuit from that to which the receiver is connected.
• Consult an experienced radio/TV technician for help.
For customers in the USA, the following booklet prepared by the
Federal Communications Commission may be of help: “How to
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Identify and Resolve Radio-TV Interference Problems”. This booklet is available from the US Government Printing Office,
Washington, DC 20402 - Stock No 004-000-00345-4.
Radio Frequency Emissions
Do not use in aircraft or hospitals. Some equipment in hospitals and aircraft are not shielded from radio frequency energy. Do not use the netpad onboard aircraft, or in hospitals, without first obtaining permission.
Do not use near pacemakers. The product may affect the operation of some medically implanted devices such as pacemakers, causing them to malfunction. Avoid placing your product next to such devices. Keep a minimum distance of 15 cm between the device and the product to reduce the risk of interference. If you have any reason to suspect that interference is taking place, turn off the netpad and contact your cardiologist for assistance.
Note: In August 1996 the Federal Communications Commission
(FCC) of the US adopted an updated safety standard for human exposure to radio frequency energy emitted by FCC regulated transmitters. The design of this product complies with the FCC guidelines and those standards.
To maintain compliance with the FCC RF exposure guidelines, if you wear the netpad on your body, use the supplied or approved carrying case, holster, or other body-worn accessory (see page 22 for details). If you do not use a bodyworn accessory, ensure the antenna is at least 1.5 cm from your body when transmitting. Use of non-approved accessories may violate FCC RF exposure guidelines.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 9
Important Safety Instructions
This equipment was tested for FCC compliance under conditions that included the use of shielded cables and connectors between it and the peripherals. It is important that you use shielded cable and connectors to reduce the possibility of causing radio and television interference. Shielded cables, suitable for the netpad, can be obtained from an authorised Psion Teklogix dealer.
If the user modifies the equipment or its peripherals in any way, and these modifications are not approved by Psion Teklogix, the FCC may withdraw the user’s right to operate the equipment.
Emissions Information For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Infrared Device Safety
Class 1 LED Product
This product includes an Infrared device for transmitting and receiving files from devices supporting the IrDA format. Although this invisible beam is not considered harmful, and complies with
EN60825-1 (IEC825-1), we recommend the following precautions when the Infrared device is transmitting:
• Do not stare into the Infrared beam.
• Do not view directly with optical instruments.
No parts in the device may be serviced by the user.
10 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Integrated Scanner Safety
For your own safety, it is critical that you comply with the warnings described in “The Scanner” on page 34.
Battery Safety Precautions
CAUTION!
Danger of explosion if a netpad battery is incorrectly handled, charged, disposed of or replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions described in “Lithium-Ion
Battery Safety Precautions”, below. Carefully review all battery safety issues listed in that section.
VORSICHT!
Explosiongefahr bei unsachgemäßem Austausch der Batterie Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.
Lithium-Ion Battery Safety Precautions
Do not store batteries at temperatures in excess of +60°C; the optimum storage temperature for maximum battery life is +10°C to +35°C.
Important: It is critical that this safety information be reviewed and that all warnings be strictly followed.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 11
BATTERIES ARE CONSIDERED HAZARDOUS WASTE. Used batteries must be disposed of in accordance with the manufacturer’s instructions, taken to an appropriate local battery recycling facility, or returned to one of the following Psion Teklogix offices for proper disposal.
Teklogix Inc. Teklogix Corp.
Teklogix S.A.
2100 Meadowvale Blvd. 1810 Airport Exchange Blvd.
Parc Club Du Golf-Bat 1.
Mississauga, Ontario
Canada
L5N 7J9
Suite 500
Erlanger, Kentucky
USA 41018
13856 Aix-En-Provence
Cedex 3
France
Warning: TO PREVENT the battery from leaking acid, generating heat or exploding, adhere to the precautions listed below.
• Use only with the authorized Psion Teklogix power adaptor.
• Do not dispose of in fire.
• Do not incinerate or subject battery cells to temperatures in excess of 100°C (212°F). Such treatment can vaporize the liquid electrolyte causing cell rupture. Incineration may result in harmful emissions or explosion.
• Do not charge, use or store batteries below -30º C
(-22° F). Batteries must be handled in accordance with all applicable state and federal laws and regulations.
• The battery incorporates built-in safety devices. To ensure their proper function, do not disassemble or alter any parts of the battery.
12 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
• Do not short-circuit the battery by directly connecting any of the exposed terminals with metal objects such as wire. Do not transport or store the battery together with metal objects such as necklaces, hair pins, etc.
• Do not use or leave the battery near a heat source such as a fire or heater.
• Do not immerse the battery in water.
• When charging, use the battery charger specifically designed for the battery.
• Do not crush, puncture, open, dismantle, or otherwise mechanically interfere with batteries.
• Do not directly solder the battery.
• Do not connect the battery to an electrical outlet, vehicle cigarette lighter, etc.
• Do not put battery into a microwave oven or pressurized container.
• Do not use the battery in combination with primary batteries (such as dry-cell batteries) or batteries of different capacities or brands.
• Immediately remove the battery from the device or battery charger and stop use if the battery gives off an odour, generates heat, becomes discoloured or deformed, or in any way appears abnormal during use.
• Do not continue charging the battery if it does not recharge within the specified charge time.
• The battery may burst or ignite if the battery leaks.
Always ensure that it is away from any exposed flames.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 13
• If a battery should leak, do not allow the contents to come into contact with your skin or your eyes. If it does, wash immediately with plenty of cold water and seek medical advice.
• Do not store the battery in extremely high temperatures (e.g., a vehicle, strong direct sunlight, etc.).
This may cause the battery to overheat or ignite, and it may also reduce the performance and service life of the battery.
• Do not use in areas where static electricity is greater than what the manufacturer guarantees.
• Keep batteries out of reach of children.
14 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
1. Introduction
This guide provides information on the operation and features of the
Psion Teklogix netpad. For additional information, refer to the netpad Win CE User Manual, the online help, or the documentation supplied with the application you are using.
1.1 Applications Installed On The netpad
The netpad is capable of running a wide variety of applications but the ones available on your particular netpad depend on the purpose for which the netpad is provided. A number of standard applications exist and custom programs can be installed easily.
The following standard programs are available:
• Wordpad , a word processor for writing letters and other documents.
• Inbox , for sending and receiving e-mail.
• Internet Explorer , for browsing the World Wide Web.
• Calculator , a calculator with general features.
1.1.1 About ActiveSync
The Microsoft PC connectivity software, ActiveSync, can be used to connect the netpad to PCs running Windows 95/98/2000/ME or NT
4.0. By connecting the netpad to a PC with a cable and running
ActiveSync on the PC, you can:
• View your netpad files from Windows Explorer by using the
Mobile Device icon in the PC’s My Computer window.
• Drag and drop files between the netpad and the PC in the same way that you would between PC drives, and they will be
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 15
automatically converted to the appropriate file format at the same time.
• Synchronize e-mail and your address book on the netpad with the PC to keep them in step with each other.
• Back up your netpad files to the PC, then restore them from the PC to the netpad again, if needed.
For detailed information, please refer to the documentation supplied with Microsoft Active Sync or the netpad Win CE User Manual .
1.2 Caring For The netpad
Screen
When used with the approved stylus, the netpad screen is very resistant to wear and impact and should last for a considerable time. Use of any object, other than the approved stylus, may result in damage to the netpad screen.
To maintain the life of the netpad screen, keep the screen clean. To clean the screen: switch off the netpad and use a soft, clean, dry cloth to gently wipe the screen. (If the netpad is set to turn on automatically when the screen is tapped, you should turn this preference off before cleaning the screen.)
Warning: Under no circumstances use chemical solvents to clean the screen.
Charging
To avoid damage to the netpad or the netpad battery packs, use only
Psion Teklogix approved chargers and docking stations.
16 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Backup Battery
The netpad has a rechargeable backup battery designed to retain data while the main battery pack is charging or changed over.
The backup battery is trickle charged from the main battery pack and has a limited lifespan. To maximize the life of the backup battery, avoid excessive discharging and recharging of the backup battery by keeping the netpad battery pack fully charged.
Important: If both the main battery pack and the backup battery are allowed to fully discharge, all user data held in
RAM will be lost.
The backup battery is not user replaceable. If the backup battery requires replacement the netpad must be returned to a Psion Teklogix approved service centre.
Drop Rating
The netpad is designed to survive being dropped on any face, onto concrete, from a height of 1.5 m (5 ft.).
Dropping the netpad from greater heights or onto harder surfaces may result in damage to the netpad.
IP Rating
The netpad is rated to IP67 and can survive submersion in water to a depth of 1 m (3.3 ft.) for up to 30 minutes. Submersion below this depth or for longer periods may result in damage to the netpad.
Operating Temperature
The netpad is designed to operate within the temperature limits of
-20°C to +60°C (-4°F to 140°F); and -20°C to +55°C (-4°F to 131°F)
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 17
for scanner variants. Use of the netpad outside of these temperature limits may reduce its life.
Avoid exposing the netpad to sudden changes in temperature, since such exposure may result in damage.
Important: As a safety precaution, charging the netpad battery should be limited to the temperature range: -20°C to
+60°C (-4°F to 140°F); and -20°C to +55°C (-4°F to
131°F) for scanner variants. Outside of these limits, the safety circuits of the netpad battery pack will not allow the battery to charge.
Storage Temperature
The netpad is designed to be stored within the temperature ranges of
-25°C to +70°C (-13°F to 158°F); and -25°C to +60°C (-13°F to
140°F) for scanner variants. Storage of the netpad outside of these temperature limits may reduce its life.
To prolong the life of the netpad battery packs during normal storage, store the netpad (and the battery pack) between +10°C and
+35°C (+50°F and +95°F).
When storing the netpad for a long period of time, the main battery should be removed and stored fully discharged.
Humidity
The netpad is designed to operate in humidity ranging from 0 to
95%. Use of the netpad in environments with condensing humidity or humidity outside these limits may result in damage to the netpad.
18 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Magnetic Fields And Static Electricity
The magnet of the netpad speaker may corrupt data stored on magnetic media. Do not keep the netpad next to credit cards or other magnetic media.
Avoid exposing the netpad to strong magnetic fields or static electricity. Such exposure may cause loss of data or result in damage to the netpad.
Service
Do not attempt to dismantle the netpad.
There are no user-serviceable parts inside, and any attempt to dismantle the netpad will invalidate the warranty.
1.3 Additional Programs And Third Party Applications
Psion Teklogix has partnered with a number of companies to provide a suite of connectivity and database tools for the netpad. Details are available on the Psion Teklogix Partner Program web site at: http://partners.psionteklogix.com/partners/ .
2. Getting Started
2.1 Features Of The netpad
This netpad is a Windows CE.Net OS-based mobile tablet computer with a 1/2 VGA touch-sensitive screen. netpad is lightweight, shock and water-resistant, and designed for use in a wide range of business areas including field service, field sales, transport, health care, hospitality, manufacturing and insurance. It is available in variants with internal GSM/GPRS, 802.11b radios and scanners.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 19
Figure 2.1 netpad Front
20
Figure 2.2 Back Of netpad
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.2 Preparing The netpad For Use
2.2.1 Fitting The Antenna
Before using netpad units fitted with either the GPRS or 802.11 radio, the antenna must be installed. The antenna should be installed as shown in Figure 2.3 below. To install the antenna turn it counter clockwise; to remove the antenna turn it clockwise.
Figure 2.3 Antenna Insertion And Removal
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 21
2.2.2 Use Of The Soft Belt Holster
Figure 2.4 Insertion Of netpad In Holster
Important: The netpad and holster have been tested to ensure compliance with the latest FCC RF exposure guidelines. For continued compliance when using the netpad and holster combination, the face shown should be fitted against the body! The user must not modify the holster in any way.
22
Figure 2.5 Holster Position On Body
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.2.3 Power Management
The netpad is powered by a Lithium Ion rechargeable battery pack, which under optimal operating conditions will provide power for a full shift. The netpad will warn you when the main battery charge is low.
Note: How long your batteries last will depend upon how you use your netpad. The netpad will use considerably more battery power when you are recording sounds, have the brightness turned up, are using files stored on a multimedia card, or are using Infrared.
You can take steps to help prolong your battery’s life:
• Turn the screen brightness down.
• Set automatic switch-off in the Power control panel.
• Use files on the internal disk instead of an MMC, as the netpad requires more power to write to the multimedia card.
The netpad can be powered from AC when used in the docking station (see page 41). When the netpad is powered from the docking station, it will also charge the battery pack.
Fitting The Battery
Before you can use the netpad you must fit the battery—slide it into place until it clicks, as shown in Figure 2.6 on page 24.
Important: Take care when replacing batteries! The netpad will warn you when its main battery is getting low, in plenty of time to change/charge it. The backup battery is designed to maintain the memory for several hours. However, prolonged reliance on the backup battery does reduce its life.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 23
Charging The netpad Battery Pack
To charge the battery, attach the battery pack to the netpad and place the complete netpad in a netpad docking station (for instructions, please refer to page 41), or place the battery in one of the optional battery chargers. The standard (850 mAH) netpad battery will normally be fully charged within 2 to 2.5 hours (3 hours for a 1400 mAH battery pack).
How Do I Check The Battery Power?
To check the battery power, open the Battery icon from the Control
Panel. The Battery tab gives a brief description of the state of the main battery.
Changing Battery Packs
If you are using your netpad away from the charger and a spare battery pack is available, you can change batteries when the battery warning is displayed. To do this:
1. Switch the netpad off.
2. Press on the battery pack latch to remove it.
3. Push in the replacement battery pack.
Battery Contact Pins
Battery Pack
Direction of
Insertion
24
Battery
Latch
Figure 2.6 Battery Insertion
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Important: Always switch off the netpad before removing the main battery.
Never remove the battery from the netpad while it is in the docking station.
Never use a netpad without a battery in the docking station.
Prolonging Battery Life
When your netpad is switched off, it is on “standby” and will continue to use a small amount of battery power. If you are going to leave your netpad switched off for a long period of time, you are advised to back up your data beforehand because the batteries will eventually run out.
Note: To check the battery power, open the Power icon from the
Control Panel.
Internal Backup Battery
The netpad has a rechargeable backup battery designed to retain data while the main battery pack is charging or changed over. The backup battery is trickle charged from the main battery pack and has a limited lifespan. To maximize the life of the backup battery, avoid excessive discharging and recharging of the backup battery by keeping the netpad battery pack fully charged.
Important: If both the main battery pack and the backup battery are allowed to fully discharge, all user data held in
RAM will be lost.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 25
The backup battery is not user replaceable. If the backup battery requires replacement, the netpad must be returned to a Psion Teklogix approved service centre.
Important: If both the batteries run out of power you will lose all your information on the internal disk.
2.2.4 Multimedia Cards
Multimedia cards (MMCs) are non-volatile memory cards, which fit into a dedicated slot in the netpad and can be used to store application software and/or data.
The MMC slot is located on the right hand side of the netpad.
Inserting And Removing An MMC
• Open the card slot door located on the side of the unit by sliding the retaining latch. Push the MMC into place until it clicks. Close the door.
• To remove an MMC, open the door and push the card. Store your MMC safely, particularly if it contains valuable data.
26
Card Slot Door Latch
MMC Card
Reset
Button
Figure 2.7 MMC Slot Location
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.2.5 Installing And Removing The SIM Card
A netpad fitted with a GSM/GPRS radio requires a Subscriber Identity Module (SIM) card installed in order for the netpad to access the
GSM network. The SIM card fits into a dedicated slot in the netpad.
The SIM card slot is located behind the Card Slot door on the righthand side of the netpad; and is located below the Multimedia card
(MMC) slot (see Figure 2.8).
Orientation of netpad
(screen side up)
MMC
SIM Card
Card Slot Door
Figure 2.8 Location Of SIM Card And MMC
Important: The MMC slot and SIM card slot are located very close together. When inserting or removing the SIM card be careful not to drop the SIM card into the
MMC slot.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 27
Inserting The SIM Card
Warning: To prevent damage to the SIM card, ensure that the netpad is switched off and the battery removed before inserting the SIM card.
• Remove the battery pack from the netpad.
• Open the card slot door located on the side of the unit by sliding the retaining latch.
• Push the SIM card into place until it is fully inserted. Note the orientation of the card, shown in Figure 2.9, with the notch of the card on the left, trailing side. Close the door.
MMC
SIM Card
Orientation of Card
(notched corner)
SIM Card Slot
Figure 2.9 Insertion Of SIM Card
Important: Ensure that the SIM card is inserted in the correct orientation as shown. Once inserted, the SIM card can only be removed using a pair of tweezers or longnosed pliers. If the SIM card is inserted incorrectly, the unit will not connect to the GSM network.
28
If the SIM card is inserted incorrectly, it must be removed by following the instructions on page 29:
“Removing The SIM Card”.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Removing The SIM Card
Warning: To prevent damage to the SIM card, ensure that the netpad is switched off and the battery removed before removing the SIM card.
• Open the card slot door and grasp the card on the cross-hatch area (see Figure 2.10), using the special removal tool supplied, a pair of tweezers, or long-nosed pliers. Pull the card out carefully.
Orientation of netpad
(screen side down)
MMC
Figure 2.10 Removal Of SIM Card
Cross-hatched Area of SIM Card
(grip here with pliers)
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 29
2.3 Turning On And Off
To switch on : press the On/Off button on the top.
Note: If the serial cable is connected to the PC and the netpad, the netpad will automatically switch on when ActiveSync on the
PC is searching for a connection.
To switch off : press the On / Off button on the top. You can switch off at any time. You do not have to save your information first, as it is automatically saved for you.
However, if you are working with a file on the MMC, save the file before switching off the netpad and removing the card.
Note: If you do not use the netpad, it will automatically switch off after a few minutes to save battery power. To continue using the netpad where you left off, switch the netpad on again using the On/Off button. The power saving options are available via the Control Panel. The automatic switch-off time may have different settings, depending on whether the netpad is in the docking station or not.
30 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.4 Finding And Using The Stylus
The stylus is located in a holder at the right. To remove it, slide the stylus out of the top of the netpad. To replace it, push it back in.
Tap lightly on the screen using the stylus. You can use your fingers to tap on the screen, though it is best to use the stylus to avoid fingerprints or smudges on the screen. Do not tap the screen with any object that has a sharp tip or you may damage the screen. Don’t use any type of ink pen, as the ink may be impossible to remove. See
“Caring For The netpad” on page 16 for instructions on how to clean the screen.
You can usually tap on (“click on”) an item with the stylus to select or change it. For example, you can:
• Double-tap (or click) a program icon, to open a program.
• Single-tap (or click) the soft keys, for “shortcuts” to system functions.
• Tap-and-hold to right-click. Right-clicking can interrupt the functionality of other tap-and-hold items, such as scrollbars.
Note: If the screen doesn’t respond to your taps, you may need to re-calibrate it. You can do this by holding down the On/Off button for 3 seconds.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 31
2.5 The Screen, Command Icons, And Toolbar
The netpad screen has a column of permanent “command icons” on the right-hand side. Some of these are user-configurable via the Soft
Keypad Settings icon in the Control Panel.
From top to bottom, the defaults for these soft keys are:
Start Menu :
This icon is user-definable.Left-clicking displays the
Control Panel. Right-clicking displays the command shell.
Backlight control:
Left-clicking displays the Brightness/Contrast control panel. Right-clicking is inactive.
Important: Battery life is considerably reduced when the brightness is increased.
Explorer:
This icon is user-definable. Left-clicking displays the
Windows Explorer. Right-clicking displays Internet
Explorer.
Keyboard:
Left-clicking displays the Software Input Panel (SIP), the onscreen keyboard. Right-clicking is inactive.
System command icon:
Left-clicking displays the Start Menu. Right-clicking displays the Soft Keypad Settings control panel.
32 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.6 How To Reset The netpad
If you find that you cannot exit a program normally, right-click on the taskbar and select Task Manager from the context menu. Select the task that appears to be unresponsive and click on the End Task button.
If this does not work, or if your netpad appears to have “locked up”, you can always perform a “soft reset”. This should restart your netpad while preserving most of your information. It is worth trying a soft reset if the keys on the netpad do not appear to respond, or if the netpad appears to switch on and you are sure that the batteries are good, but the screen is otherwise blank.
To perform a soft reset : gently press the stylus onto the reset button. This is located inside the card slot door cover to the side of the MMC slot.
MMC
SIM Card
Reset Button
Figure 2.11 Reset Button Location
Press the On/Off button to restart the netpad—you will hear two beeps during boot-up to indicate the reset. After a soft reset, any
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 33
changes to open files will be lost. Your other files on the internal disk will almost always be safe.
It is possible (although unlikely) that performing a soft reset after a program failure may cause the netpad to lose the information on the internal disk; it could even prevent the reset from working at all. If this happens, you will have to perform a “hard reset”.
Important: A hard reset resets the netpad completely, and all information on the Internal disk will be lost.
To perform a hard reset :
1. Remove the netpad from the docking station (if applicable).
2. Remove the main battery.
3. Press and hold down the On/Off button (on the top of the unit).
4. While continuing to hold down the On/Off button, press and release the Reset button.
5. Release the On/Off button.
6. Refit the battery into the netpad—the unit will power up and you will hear one beep during boot-up.
Note: Hard resetting the netpad will delete the partnership on the netpad. You may delete and re-create the partnership on the
PC, or create another partnership with a new name. Refer to
ActiveSync’s online help for more details on this operation.
2.7 The Scanner
Where fitted with a bar code scanner, the netpad may be used to read industry standard bar codes. To scan a bar code, point the scanner window at the bar code, ensuring that the scanner window is not obstructed and that you are between 5 cm (2 in) and 60 cm (24 in) from the bar code. Activate the scanner as instructed in the software
34 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
application’s operating instructions. The scanning beam should be energized until a successful decode is achieved or three seconds have elapsed.
Scanner Window
Figure 2.12 Scanner Location
Warning: For your own safety, it is critical that you comply with the following warnings:
1. Do not look into the scanner window.
2. This product contains a laser scanner that emits less than 1.2 mW average radiant power at a wavelength of 650 nm. This product complies with 21
CFR 1040.10, 1040.11 and DIN EN 60825-1:
January 2001, and is classified as a Class 2 laser product.
3. CAUTION – Using controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure.
4. CAUTION – The use of optical instruments with this product will increase eye hazard.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 35
2.8 First Steps
When you first switch on the netpad, you will see the Calibration screen. You must calibrate successfully to continue. After calibration, you will see the Time/Date control panel. Input the correct time, date, and time zone information. Click the OK button in Time/Date control panel to close and save your changes. You will then see the
Windows Desktop.
2.8.1 Navigating Between Files And Folders
• Double-click on a folder icon to open that folder. Click on the
X icon to close it. Click on the Up Folder icon to move back up one level.
• Click on a file to select it. Double-click to open it.
Up Folder
X icon
2.8.2 Starting Programs
When you open a file, the correct program for this file is started automatically. You can also start programs by clicking on them from the Start Menu . You don’t have to close one program before opening another. The taskbar displays all open applications.
36 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.8.3 Programs And Files
To create a new file : open the program, select the New command on the File menu and type in the name for the new file (see “Entering Information”, below). The file will now be created. You can start entering your information.
It is a good idea to keep related files together in a folder, to make the files easier to find later.
2.8.4 Entering Information
You can enter information and complete tasks using the stylus or the on-screen keyboard. The on-screen keyboard is displayed by clicking the
Keyboard soft key.
To move the keyboard, drag it by the title bar.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 37
To display and set the keyboard preferences, go to the Control Panel and open the Input Panel icon. Clicking on the
Options button will let you set such preferences as button size and special gestures for use with the keyboard.
Note: The on-screen keyboard is the netpad’s default keyboard. It is possible that your netpad may have more than one keyboard, if you have third-party software installed. To choose which keyboard to use, go to the Control Panel and click on the
Input Panel icon. The dropdown menu will show all available keyboards.
2.8.5 Using Menus
You can usually select a menu command to perform tasks.
• Click on the menu you want to access from the menu bar.
• Tap on the menu names and commands, or use the arrow keys to move around the menus. Tap on commands marked with a
or press the right arrow key to see further commands.
A menu command with three dots at the end means that selecting the command will display a “dialogue” where you enter more information (see “Using Dialogues”, on page 39).
If a menu command is grey, it means that it’s not currently available; e.g. you cannot Copy unless you have first selected something to copy.
38 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
2.8.6 Using Dialogues
A “dialogue” appears when you need to make selections and enter further information. You can move between dialogue items by tapping on them, or using the up and down arrow keys. Dialogues contain one or more of the following elements:
Textbox: where you just type in your information. When you tap in the textbox, you will need to open the on-screen keyboard to enter text.
Dropdown: where you select from a number of options. You will see left and right arrows around the current selection; you can change the selection by tapping on the arrows, by pressing the left and right arrow keys, or by typing the first letter of the option you want.
Checkbox: where you make a choice between selecting an option or not selecting it. Just tap on the checkbox, or press the left and right arrow keys to add or remove a checkmark.
Radio buttons: where you make one choice from a number of options. Just tap on an option, or use the left and right arrow keys to make a selection.
If an item is grey, it is currently not available. For example, if you do not have a transflective display, the Backlight On checkbox in Backlight Properties will be greyed out.
Some dialogues comprise a number of “pages”, each page has a
“tab” at the top. Tap on the tab, or move the highlight to the tab name, to go to that page. You can also move a dialogue around the
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 39
screen by holding the stylus on the dialogue title bar and dragging it across the screen.
Tabs in dialogue page
Checkbox Dropdown
Dialogue Buttons
Dialogues usually include standard buttons such as Ok and X . Some buttons have a standard keypress equivalent:
• Usually, you can tap the OK button or press the Enter key if you want to save information and remove the dialogue.
• Tap the Cancel button, the X button, or press the Esc key if you want to close the dialogue without saving the information.
• For dialogues that ask a question, you can tap the Yes button or press the Y key for ‘yes’; tap the No button, press the N key, or press the Esc key for ‘no’.
2.8.7 Copying Information Between Programs
You can insert information created in one program into a different program. For example, you may want to compose text in Wordpad before copying it into an e-mail message in the Inbox. If you try to insert an object into a program that is not designed to handle that
40 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
type of object, you will be unable to Paste. Trying to copy a file from
Windows Explorer into a Wordpad document will not work because
Wordpad will keep the Paste option greyed out until it detects that text is ready to be pasted.
3. The netpad Docking Station
This section describes the netpad docking station. The docking station is used as a convenient “drop-in” holder for the netpad, supplying power and communications through the docking station connector.
3.1 Using The Docking Station
Release Button
IR Ports netpad Connectors Communication Ports
Yellow LED indicates communications
Red LED indicates charging/
Green LED indicates charged
Red LED indicates power
Power Jack
Figure 3.1 Docking Station Features
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 41
To insert the netpad into the docking station, align the two devices, and press down on the netpad until the connection is made. To eject, press down on the release button at the top of the docking station.
The netpad will be pushed up and out of the docking station.
While the netpad is in the docking station, the communications port on the netpad can still be used. The docking station communications port is available for convenience.
You can rotate the orientation of the docking station on its stand.
Hold the top of the docking station in one hand and the bottom in the other. Lift the top part to release it and rotate through 90°. When you let go of the top part, it will click into place.
3.2 Communications Settings
When performing PC communications, it is necessary to define the communication settings.
In the PC Connection icon in the Control Panel, verify that the checkbox that allows connection to the desktop is checked.
• Serial Port 3 specifies using the RS232 communications port on the netpad.
• Docking Station specifies using the RS232 communications port on the docking station.
• Infrared Port specifies using the IR port on the back of the netpad.
To change the connection type, click on the Change...
button and select the connection from the dropdown list.
42 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
4. Support Services And Worldwide Offices
Psion Teklogix provides a complete range of product support services to its customers worldwide. These services include technical support and product repairs.
4.1 Technical Support
Technical Support for the netpad is provided via e-mail through the
Partner Program website. To reach the website, go to www.psionteklogix.com
and click on the Partner Program link, which takes you to the Partner Program page. Then click on the “Log-in” button or the
“Register” button, depending on whether you have previously registered for Teknet or the Partner Program. (Your UserID and password are the same for TekNet and the Partner Program.)
4.2 Product Repairs
International
For product repairs, please contact your local Psion Teklogix office
(see “Worldwide Offices” on page 44).
Canada/U.S.A
Canadian and U.S. customers can receive access to repair services, by calling the toll-free number below, or via our secure website.
Note: Customers calling the toll-free number should have their
Psion Teklogix customer number or trouble ticket number available.
Voice: 1 800 387-8898 (press option “2”)
Fax: 1 905 812-6304
Web Site: http://service.psionteklogix.com
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 43
4.3 Worldwide Offices
C OMPANY H EADQUARTERS
A ND C ANADIAN S ERVICE
C ENTRE
Psion Teklogix Inc.
2100 Meadowvale Boulevard
Mississauga
Ontario
Canada L5N 7J9
Tel: +1 905 813 9900
Fax: +1 905 812 6300
E-mail: [email protected]
N ORTH A MERICAN
H EADQUARTERS A ND U.S.
S ERVICE C ENTRE
Psion Teklogix Corp.
1810 Airport Exchange Boulevard
Suite 500
Erlanger, Kentucky
USA 41018
Tel: +1 859 371 6006
Fax: +1 859 371 6422
E-mail: [email protected]
I NTERNATIONAL S UBSIDIARIES
Psion Teklogix GmbH
Jakob Kaiser Straße 3
D-47877 Willich Münchheide
Deutschland
Tel: +49 2154 9282 0
Fax: +49 2154 9282 59
E-mail: [email protected]
Psion Teklogix (UK) Ltd.
Bourne End Business Centre
Cores End Road
Bourne End
Buckinghamshire SL8 5AR, England
Tel: +44 1628 648800
Fax: +44 1628 648810
WWW: www.teklogix.co.uk
E-mail: [email protected]
Psion Teklogix S.A.
La Duranne
135 Rue Rene Descartes
BP 421000
13591 Aix-En-Provence
Cedex 3; France
Tel: +33 (0) 4.42.908.809
Fax: +33 (0) 4.42.908.888
E-mail: [email protected]
44
Psion Teklogix AB
Stora Badhusgatan 18-20
411 21 Göthenburg, Sweden
Tel:
Fax:
+46 31 13 15 50
+46 31 13 57 80
E-mail: [email protected]
Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Psion Teklogix Finland
Metsänneidonkuja 8
02130 Espoo
Finland
Tel: +358 9 4307 8390
Fax: +358 9 4307 8395
E-mail: [email protected]
Psion Teklogix de Mexico, S.A. de C.V.
Sierra Mojada 626, 2º Piso
Col. Lomas Barrilaco, C.P. 11010
Mexico, D.F., Mexico
Tel: +52 55 5 327 1124
Fax: +52 55 5 327 1123
E-mail: [email protected]
Psion Teklogix Danmark
Vesterballevej 4-6
7000 Fredericia
Danmark
Tel: +45 76 24 0133
Fax: +45 75 94 4679
E-mail: [email protected]
Psion Teklogix do Brasil, Ltda.
Al. Casa Branca, 851 - conj. 101 e 102
São Paulo - SP - 01408-001
Brasil
Tel: +55 11 3064 0868
Fax: +55 11 3068 8198
WWW: www.teklogixbrasil.com.br
E-mail: [email protected]
Psion Teklogix Italia S.r.I
Via Galilei, 47
20092 Cinisello Balsamo
Milan, Italy
Tel:
Fax:
+39 2 6604 5410
+39 2 6604 5412
E-mail: [email protected]
Chile Psion Teklogix International Inc.
Avenida Vitacura 2909, Oficina 703
Las Condes
Santiago, Chile
Tel: +56 2 334 9344
Fax: +56 2 233 3868
E-mail: [email protected]
Psion Teklogix Inc. (Singapore)
583 Orchard Road
# 15-01 Forum
Singapore 238884
Psion Teklogix de Argentina,
S.A.
Avenida Moreau de Justo 1180
Piso 1, Oficina C-105
Buenos Aires 1107 Tel: +65 735 8108
Fax: +65 733 5990
E-mail: [email protected]
Argentina
Tel: +54 11 4343 0193
Fax: +54 11 4343 6310
E-mail: [email protected]
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 45
Psion Teklogix España, S.L.
Cityparc Ronda de Dalt
Ctra. Hospitalet 147-149
Edificio Atenas 2° 3ª
08940 Cornellà de Llobregat (Barcelona)
España
Tel: +34 9 3475 0220
Fax: +34 9 3475 0230
E-mail: [email protected]
Psion Teklogix Systems India
Pvt. Ltd.
M-74, 1st Floor, “M” Block Market
Greater Kailash-Il
New Delhi - 110048
India
Tel: +91 11 26219257
Fax: +91 11 26219076
E-mail: [email protected]
Psion Teklogix Africa
Postnet Suite 39, Private Bag x11
Halfwayhouse, 1685 Ground Floor
East
Waterfall Edge Phase 2, Waterfall
Park
Bekker Road MIDRAND 1685
South Africa
Tel: +27 11 805 7440/1/2
Fax: +27 11 805 7444
Psion Teklogix Benelux
Nieuwe weg 1,
2070 Zwijndrecht
Belgium
Tel: +32 (0)3 250 22 00
Fax: +32 (0)3 250 22 20
E-mail: [email protected]
4.4 Worldwide Web
www.psionteklogix.com
Psion Teklogix B.V.
Venrayseweg 57,
5928 NZ Venlo
Nederlands
Tel: +31 77 32400 44
Fax: +31 77 32400 53
Psion Teklogix Taiwan Co., Ltd.
15FL-5, No. 366 Boai 2nd Road,
Tzuo Ying District, KAOHSIUNG 813
Taiwan, R.O.C.
Tel: +886 7 558 2028
Fax: +886 7 558 3328
E-mail: [email protected]
46 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Touch-sensitive screen
Built-in scanner(some variants)
Windows CE.Net OS
GPRS/GSM and 802.11b radio options
Shock and water resistant
Multimedia card slot
Docking station support
Frequently asked questions
Press the On/Off button.
Perform a soft reset by pressing the stylus onto the reset button, located inside the card slot door.
The stylus is located in a holder on the right side of the netpad.
Open the Battery icon from the Control Panel.
No, avoid exposing the netpad to strong magnetic fields, which may corrupt data or damage the device.
