advertisement
changes to open files will be lost. Your other files on the internal disk will almost always be safe.
It is possible (although unlikely) that performing a soft reset after a program failure may cause the netpad to lose the information on the internal disk; it could even prevent the reset from working at all. If this happens, you will have to perform a “hard reset”.
Important: A hard reset resets the netpad completely, and all information on the Internal disk will be lost.
To perform a hard reset :
1. Remove the netpad from the docking station (if applicable).
2. Remove the main battery.
3. Press and hold down the On/Off button (on the top of the unit).
4. While continuing to hold down the On/Off button, press and release the Reset button.
5. Release the On/Off button.
6. Refit the battery into the netpad—the unit will power up and you will hear one beep during boot-up.
Note: Hard resetting the netpad will delete the partnership on the netpad. You may delete and re-create the partnership on the
PC, or create another partnership with a new name. Refer to
ActiveSync’s online help for more details on this operation.
2.7 The Scanner
Where fitted with a bar code scanner, the netpad may be used to read industry standard bar codes. To scan a bar code, point the scanner window at the bar code, ensuring that the scanner window is not obstructed and that you are between 5 cm (2 in) and 60 cm (24 in) from the bar code. Activate the scanner as instructed in the software
34 Psion Teklogix netpad Win CE 4.0 Quick Start Guide
application’s operating instructions. The scanning beam should be energized until a successful decode is achieved or three seconds have elapsed.
Scanner Window
Figure 2.12 Scanner Location
Warning: For your own safety, it is critical that you comply with the following warnings:
1. Do not look into the scanner window.
2. This product contains a laser scanner that emits less than 1.2 mW average radiant power at a wavelength of 650 nm. This product complies with 21
CFR 1040.10, 1040.11 and DIN EN 60825-1:
January 2001, and is classified as a Class 2 laser product.
3. CAUTION – Using controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure.
4. CAUTION – The use of optical instruments with this product will increase eye hazard.
Psion Teklogix netpad Win CE 4.0 Quick Start Guide 35
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Approvals And Safety Summary
- 19 1. Introduction
- 19 1.1 Applications Installed On The netpad
- 19 1.1.1 About ActiveSync
- 20 1.2 Caring For The netpad
- 23 1.3 Additional Programs And Third Party Applications
- 23 2. Getting Started
- 23 2.1 Features Of The netpad
- 25 2.2 Preparing The netpad For Use
- 25 2.2.1 Fitting The Antenna
- 26 2.2.2 Use Of The Soft Belt Holster
- 27 2.2.3 Power Management
- 30 2.2.4 Multimedia Cards
- 31 2.2.5 Installing And Removing The SIM Card
- 34 2.3 Turning On And Off
- 35 2.4 Finding And Using The Stylus
- 36 2.5 The Screen, Command Icons, And Toolbar
- 37 2.6 How To Reset The netpad
- 38 2.7 The Scanner
- 40 2.8 First Steps
- 40 2.8.1 Navigating Between Files And Folders
- 40 2.8.2 Starting Programs
- 41 2.8.3 Programs And Files
- 41 2.8.4 Entering Information
- 42 2.8.5 Using Menus
- 43 2.8.6 Using Dialogues
- 44 2.8.7 Copying Information Between Programs
- 45 3. The netpad Docking Station
- 45 3.1 Using The Docking Station
- 46 3.2 Communications Settings
- 47 4.1 Technical Support
- 47 4.2 Product Repairs
- 48 4.3 Worldwide Offices
- 50 4.4 Worldwide Web