Keep these instructions in a location which is easily accessible to every user and make these instructions available to every new owner of the device.

WARNING!

The operating instructions contain important safety information!

Failure to observe these instructions may result in hazardous situations.

` The operating instructions must be read and understood.

Symbols:

DANGER!

Warns of an immediate danger!

` Failure to observe these instructions will result in death or serious injuries.

WARNING!

Warns of a potentially dangerous situation!

` Failure to observe these instructions may result in serious injuries or death.

CAUTION!

Warns of a possible danger!

` Failure to observe this warning may result in a moderate or minor injury.

NOTE!

Warns of material damage!

` Failure to observe these instructions may result in damage to the device or the system.

Indicates important additional information, tips and recommendations.

Refers to information in these operating instructions or in other documentation.

` Highlights instructions to avoid a danger.

→ Designates a procedure which you must carry out.

english

Type 8681 büS/CANopen

Basicsafetyinstructions

2 BASIC SAFETY INSTRUCTIONS

These safety instructions do not make allowance for any

• eventualities and events which may occur during installation, operation and maintenance of the devices.

• local safety regulations which the operator is responsible for observing, also in relation to the installation personnel.

DANGER!

Danger from high pressure!

` Before loosening lines and valves, turn off the pressure and vent the lines.

WARNING!

Danger due to electric voltage!

` Before reaching into the system (apart from the teach-in procedure in a non-explosive atmosphere), switch off the voltage and secure to prevent it from being switched on again!

` Observe the applicable accident prevention and safety regulations for electrical equipment!

General hazardous situations.

To prevent injuries:

` Ensure that the system cannot be activated unintentionally.

` Installation and maintenance work as well as operator actions may only be carried out by authorized and suitably qualified technicians using the appropriate tools.

` Do not make any unauthorized internal or external changes to the device!

` The process is restarted in a defined or controlled manner after an interruption in the power supply or pneumatic supply.

` The device may be installed and operated only when in perfect condition and in consideration of the operating instructions.

` The general rules of technology apply to application planning and operation of the device.

NOTE!

Electrostatic sensitive components / modules!

• The device contains electronic components which are sensitive to electrostatic discharge (ESD). Contact with electrostatically charged persons or objects may be hazardous to these components. In the worst case scenario, they will be destroyed immediately or will fail after start-up.

• Observe the requirements in accordance with EN 61340-5-1 to minimise or avoid the possibility of damage caused by a sudden electrostatic discharge!

• Ensure that you do not touch the electronic components when the power supply voltage is applied!

7 english

Type 8681 büS/CANopen

Basicsafetyinstructions

NOTE!

Risk of damage to property!

• Do not connect any mechanically rigid connection parts, in particular those with long lever arms, as such connections could generate torques that might damage the control head.

• Do not supply the medium connections of the system with liquids or aggressive or flammable media!

• Do not subject the housing to mechanical loads (e.g. by placing objects on it or standing on it).

• Do not make any unauthorised external changes to the housings of the device. Do not paint housing parts or screws.

• Only use compatible cleaning agents for cleaning the securely closed control head and always rinse thoroughly with clean water.

8 english

Type 8681 büS/CANopen

Generalinformation

3 GENERAL INFORMATION

These Additional Instructions are an supplement to the basic operating instructions for Type 8681.

They only describe the extensions and specifications for Type 8681 büS/CANopen.

“büS” (Bürkert system bus) stands for the communication bus developed by Bürkert and is based on the

CANopen protocol.

The following examples refer to the application of the EtherNet/IP protocol using a Bürkert gateway. The following bus systems are also supported by the Bürkert Gateway:

PROFINET, Modbus/TPC, PROFIBUS DPV1, EtherCAT, CC-Link - corresponding configurations on request.

3.1 Conformity / Standards

The Control Head Type 8681 büS/CANopen complies with the EU directives according to the EU Declaration of

Conformity.

The applied standards, which are used to demonstrate compliance with the EU Directives, are listed in the EU

Prototype Examination Certificate and/or the EU Declaration of Conformity.

3.2 Approvals

The Control Head Type 8681 büS/CANopen is not authorised for those application areas which are described by the ATEX Directive and the directives for the Underwriters Laboratories (UL) and Factory Mutual (FM).

english

Type 8681 büS/CANopen

Quickstartforinitialstart-up

4 QUICKSTART FOR INITIAL START-UP

“büS” (Bürkert system bus) stands for the communication bus developed by Bürkert and is based on the CANopen protocol. The following steps refer to the application of the e.g. EtherNet/IP protocol using a Bürkert gateway preconfigured for a maximum of 63 control heads.

For other gateway configurations (e.g. in conjunction with ELEMENT positioners), the specific documentation for preconfigured Bürkert gateways must be observed.

After mounting the control heads (Type 8681 büS/CANopen) in the network, the following operations must first be carried out on the control heads:

1.) Addressing of the control heads

According to chapter “6.13.2 Setting the büS/CANopen address (Node ID)” each control head in the network must

be assigned its own unique address (Node-ID).

When using a preconfigured gateway: For easy commissioning, each control head should be assigned its unique node ID between 1 and 63 using the DIP switches. This allows the preconfigured communication settings between the gateway and each control head to be used. The factory setting (address “0” = softwareconfigurable address/ node ID) should not be used furthermore.

When using a non-pre-configured gateway or when using the factory setting “0” (software-configurable address/node ID): A device configuration via Bürkert Communicator on site is required for commissioning each

control head (see also section “6.13.3” on page 36 ).

Error-free parameter access by the Logix Designer: To ensure this, the new addresses should be selected clearly arranged and in sequence (starting with “1” and without gaps in the numerical series!).

Any change of the device address requires a device restart.

2.) Setting the baud rate

Set the baud rates according to chapter “6.13.1 Setting the baud rate”. The combination of cable lengths and baud

rate is very important (see chapter “6.5.2 Total line length and drop line lengths of the bus cables”).

The baud rate of all devices connected to the network (including the gateway) must be the same .

Any change of the baud rate requires a device restart.

3.) “Hiding” of non-existent devices

If less than 63 devices are assigned to the gateway, the non-existent devices must be “hidden” at the gateway, both

outputs AND inputs - see chapter “6.17 Configuration of the control head network”, either using the Logix-Designer

(“6.17.1”) or Bürkert Communicator (“6.17.2”).

After the changes have been made, a device restart is required.

4.) Careful closing of the electrical connections

Due to moisture (including steam) in the system, all electrical connections (M12 plug-in connections) must be firmly screwed on with 0.6 (+0.1) Nm. All open electrical connections must be well “sealed” with protective

caps (see information box in chapter “6.2 Network principle / Interfaces” and also chapters “7 Accessories” and

“8 Cabling examples”.

english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

5 CHANGES CONCERNING BÜS/CAN OPEN

DESIGN

This chapter describes changes affecting the Control Head Type 8681 büS/CANopen design with reference to the Basic Operating Instructions (OI) for Type 8681.

5.1 “Autotune functions” – with reference to the Basic

OI for Type 8681

The optical feedback signals for the autotune mode and the autotune functions of type 8681 büS/CANopen are different from the standard models of type 8681.

For the autotune functions, first enter the Autotune mode (T2+T3 for min. 2.5 s), then choose one of the 6 Auto tune functions:

Teach button

Mode Activation duration optical feedback for “Autotune mode active”

Teach button

Function Activation duration optical feedback for “Autotune function active”

T2 + T3

Autotune mode

2.5 s red + yellow + green flashing sequentially

(500 ms per colour)

T1 + T2

T1 + T3

T2 + T3

Autotune 1

Autotune 2

Autotune 3

Autotune 4

Autotune 5

Autotune 6

0.5 s red + yellow + green flashing sequentially

(200 ms per colour ) *)

*) This display for “Autotune function active” applies only to the display mode “device-specific LED mode”

(“8681 Classic 0 ... 15”)

– see chapter “5.2.1”.

In the case of other display modes of the device status LED (Top LED) – compare chapter

“5.2.1” – the colour

and blinking pattern display differs for the “Autotune function active” . See also:

- NAMUR mode

(chapter “5.2.2”

) – displayed in color orange as “function check”.

- valve mode (chapter

“5.2.3” ) – no display

- valve mode + errors

(chapter “5.2.4”

) – no display

- valve mode + errors + warnings (chapter

“5.2.5”

) – displayed in color orange as “function check”

5.2 “Setting colour combinations” – with reference to the Basic OI for Type 8681

Position feedback (S1, S2, S3, S4IN) of the process valve as well as error and warning messages are displayed by means of the device status LED (Top LED) in different colours and partially blinking patterns. Different display modes and colour combinations can be selected for Type 8681 büS/CANopen.

This display mode and the colour coding of the büS/CANopen devices can be switched using the 6 DIP switches

for colour coding on the electronic module (see “Fig. 6” on page 31).

(As of firmware version B.02.00.00 the following applies “Tab. 1”.)

11 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 Description of the display modes of the device status LED (Top LED)

X X X X 0 0 8681 “Classic Mode” : the colour combinations for the position and error feedback are set using DIP switches 1 to 4 as described in the Basic Operating Instructions, chapter

“Setting colour combinations”

– see also chapter “5.2.1”

1 1 1 1 1 0 Factory settings: software-configurable display mode: display mode of the device status LED can be selected by firmware:

- Device-specific LED mode (8681 Classic 0 ... 15) – see chapter “5.2.1”

- NAMUR mode – see chapter “5.2.2”

- Valve mode – see chapter “5.2.3”

- Valve mode + errors – see chapter “5.2.4”

- Valve mode + errors + warnings (factory setting)

– see chapter “5.2.5”

- Fixed colour – see chapter “5.2.6”

- (Top) LED off (there is no feedback via Top LED)

(In the Bürkert Communicator the display modes can be found under:

General settings -> Parameters -> Status LED -> Mode)

PLEASE NOTE:

Hardware-configured values (that means: set via DIP switches) overwrite the software-configured display mode!

Tab. 1:

0 NAMUR mode:

The device status is displayed according to NAMUR NE 107 – see chapter

“5.2.2”

0 Valve mode:

Display of the position feedback – see chapter “5.2.3”

0 Valve mode + errors:

Display of the position and error feedback – see chapter “5.2.4”

0 Valve mode + errors + warnings:

Display of the position and error feedback as well as warnings – see chapter

“5.2.5”

X all other combinations: (Top) LED off

Colour combinations / colour coding / display modes for Type 8681büS/CANopen

12 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

5.2.1 Device-specific LED mode “8681 Classic Mode”

This display mode of the device status LED for the position feedback (S1, S2, S3, S4IN) of the process valve matches the display mode of the “classic” Control Heads Type 8681 (24 V DC, AS-i, DeviceNet, 120 V AC). The colour coding is set using DIP1 to 4 - see Basic Operating Instructions, chapter “Setting colour combinations”.

If the display mode is selected using software – e.g. via Bürkert Communicator (General Settings/Parameters/

Status LED) or via the network (e.g. via Logix Designer) – the parameter “8681 Classic X” can be selected under

“device-specific LED mode”. Which DIP switch position corresponds to the respective parameter is listed in ”Tab. 2”:

S1 green red green red

Tab. 2:

S2 red green red

S3 green yellow green yellow green yellow green red green red green red green yellow yellow yellow green green green red red red red

S4 red green green green yellow green green yellow green yellow yellow

Error red red yellow yellow red red yellow yellow red red green green yellow red green yellow yellow yellow yellow green green green red yellow red red yellow green green green yellow

DIP1

DIP2

DIP3

DIP4 Designation of the device-specific LED mode

0 8681 Classic 0

8681 Classic 1

8681 Classic 2

8681 Classic 3

8681 Classic 4

8681 Classic 5

8681 Classic 6

8681 Classic 7

8681 Classic 8

8681 Classic 9

8681 Classic 10

8681 Classic 11

8681 Classic 12

8681 Classic 13

8681 Classic 14

8681 Classic 15

Colour combinations / colour coding for Type 8681 büS/CANopen - device-specific LED mode “8681 Classic X”

5.2.2 NAMUR mode

The device status LED (Top LED) display the device status, they change colour according to NAMUR NE 107

(edition 2006-06-12). There is no feedback on the process valve positions (S1, S2, S3, S4IN).

This display mode can be configured by software (DIP 1 to 6: 111110) or can be fixed as of firmware revision

B.02.00.00 using DIP switches (DIP 1 to 6: 001110) – compare “Tab. 1”.

If several device statuses exist simultaneously, the device status with the highest priority is displayed. The priority is determined by the severity of the deviation from controlled/normal operation (red LED = failure = highest priority) –

see “Tab. 3”.

13 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

Colour *) Prio- rity

Description Meaning red orange yellow blue green

Failure, error, malfunction

Function check

Out of specification

Maintenance required

Diagnostics active

(controlled operation)

Controlled operation is not possible due to a malfunction in the device or its peripheral devices.

Work is being carried out on the device; controlled operation is therefore not currently possible

(this includes “Autotune function active”).

The ambient conditions or process conditions for the device are outside the specified area

(this includes “Teach or Autotune function required”).

The device is in controlled operation, but a function is presently restricted.

→ Service the device!

Device is operating faultlessly (controlled). Status changes are indicated in different colours.

Messages are transmitted via a fieldbus if connected.

Tab. 3: Description of the colours in display mode “NAMUR”

*) If a control head is connected to the Bürkert Communicator, this control head “flashes” (single flash) in the particular co-

lour of the device status – see also the chapter on Localisation function “5.3.3”.

5.2.3 Valve mode

The device status LED (Top LED) display the position feedback (S1, S2, S3) of the process valve and the feedback S4IN from the external initiator.

The position feedback is displayed as shown below in “Tab. 4”. There is no display of error and warning messages

in this mode.

This display mode can be configured by software as of firmware revision B.02.00.00 (DIP 1 to 6: 111110) or can

be fixed using DIP switches (DIP 1 to 6: 011110) – see “Tab. 1”.

Position Process valve

S3 position, e.g.: closed open

Cycle stroke

Colour Blinking pattern of the position feedback green *) continuously lit yellow *) continuously lit green *) continuously flashing slowly **)

(250 ms ON, 250 ms OFF)

S4IN ext. Initiator, active green *) continuously flashing quickly **)

(125 ms ON,125 ms OFF)

If there is no position feedback (S1 to S4IN), i.e. the process valve is in intermediate positions of the defined teach points, the Top LED is off *) ***) .

Tab. 4: Description of the colours and blinking patterns in “valve mode” display mode

*) Factory settings (other selectable colours for S1 to S4IN and also for the intermediate positions: white, green, blue, yellow, orange, red, (Top) LED off)

**) Factory settings (other selectable blinking patterns: [continuously lit], [125 ms ON + 125 ms OFF],

[250 ms ON + 250 ms OFF])

***) Blinking pattern for the selected colour for the intermediate positions: continuously lit english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

5.2.4 Valve mode + Errors

The device status LED (Top LED) display the position feedback (S1, S2, S3) of the process valve and the feedback S4IN from the external initiator as well as error messages.

The position feedback is displayed as shown below in “Tab. 5”.

If an error (i.e. internal error, bus error, error with teach or Autotune function, positions measuring sys tem signal error) occurs, this is also displayed alternately according to the diagram: 1 second position feedback / 1 second error display.

This display mode can be configured by software as of firmware revision B.02.00.00 (DIP 1 to 6: 111110) or can

be fixed using DIP switches (DIP 1 to 6: 101110) – see “Tab. 1”.

Position Process valve position, e.g.:

Colour Blinking pattern of the position feedback closed open green *) continuously lit yellow *) continuously lit

Cycle stroke green *) continuously flashing slowly **)

(250 ms ON, 250 ms OFF)

Fault indication is lit red alternating with colour from S1 is lit red alternating with colour from S2 is lit red alternating with colour from S3

S4IN ext. Initiator, active green *) continuously flashing quickly **)

(125 ms ON,125 ms OFF) is lit red alternating with colour from

S4IN

If there is no position feedback (S1 to S4IN), i.e. the process valve is in intermediate positions of the defined teach points, the Top LED is off *) ***) .

Tab. 5: Description of the colours and blinking patterns in “valve mode + errors” display mode

*) Factory settings (other selectable colours for S1 to S4IN and also for the intermediate positions: white, green, blue, yellow, orange, red, (Top) LED off)

**) Factory settings (other selectable blinking patterns: [continuously lit], [125 ms ON + 125 ms OFF],

[250 ms ON + 250 ms OFF])

***) Blinking pattern for the selected colour for the intermediate positions: continuously lit (alternating with possible error messages)

5.2.5 Valve mode + Errors + Warnings

The device status LED (Top LED) display the position feedback (S1, S2, S3) of the process valve and the feedback S4IN from the external initiator as well as error and warning messages.

The position feedback is displayed as shown in “Tab. 6”.

If an error or a warning

occurs (see colour assignment below “Tab. 6”), this is also displayed alternately:

1 second position feedback / 1 second error or warning display.

This display mode can be configured by software as of firmware revision B.02.00.00 (DIP 1 to 6: 111110) or can

be fixed using DIP switches (DIP 1 to 6: 110110) – see “Tab. 1”.

15 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

Position Process valve position, e.g.:

S3 closed open

Cycle stroke

S4IN ext. Initiator, active

Colour Blinking pattern of the position feedback green yellow green

*) continuously lit continuously lit continuously flashing slowly

(250 ms ON, 250 ms OFF)

**) green *) continuously flashing quickly **)

(125 ms ON,125 ms OFF)

Fault indication Warning display is lit red

(= error colour ***) ) alternating with colour and any blinking pattern of the position (S1 or S2 or S3 or S4IN) is lit in the warning colour ****) alternating with colour and any blinking pattern of the position (S1 or S2 or S3 or

S4IN)

If there is no position feedback (S1 to S4IN), i.e. the process valve is in intermediate positions of the defined teach points, the Top LED is off *) .

(Blinking pattern for the intermediate positions with selected colour (different from the factory setting “(Top)

LED off”): continuously lit, alternating with possible warning or error messages)

Tab. 6: Description of the colours and blinking patterns in “valve mode + errors + warnings” display mode

*) Factory settings (other selectable colours for S1 to S4IN and also for the intermediate positions: white, green, blue, yellow, orange, red, (Top) LED off)

**) Factory settings (other selectable blinking patterns: [continuously lit], [125 ms ON + 125 ms OFF],

[250 ms ON + 250 ms OFF])

***) Error colour: red (internal error, bus error, error with teach or Autotune function, positions measuring

sys tem signal error)

****) Warning colours: (firmly specified):

Orange: Function check (service mode/manual override active, Autotune function active)

Yellow: Out of specification (storage error of the operating hour/cycle counter, Teach

or Autotune function required (no position taught))

Blue: Maintenance required (Service/maintenance notification)

5.2.6 Display mode “Fixed colour”

A fixed colour can be assigned to the device - however this is possible only in software configurable display mode

(DIP 1 to 6: 111110). There is no display of process valve positions or error/warning messages in this mode –

compare “Tab. 1”.

Bürkert Communicator can be used to select the following colours: white, green, blue, yellow, orange, red, teal, pink (factory settings: (Top) LED off).

english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

5.3 “Blinking pattern & fault signalling” – with reference to the Basic OI for Type 8681

The device status LED (Top LED) display the position feedback (positions) S1, S2, S3 of the process valve, the feedback S4IN from the external initiator as well as error and warning messages, partly using special “blinking patterns”. How these are displayed, depends on the selected display mode of the device status LED.

5.3.1 Position feedback in normal operation

No.

Blinking pattern ON

OFF Note continuously lit in the respective position colour:

Signal from S1 and S2 (factory settings)

250 ms 250 ms continuously flashing in the respective position colour:

Signal from position S3 (factory settings)

125 ms 125 ms continuously flashing in the respective position colour:

Signal from the external initiator S4 (factory settings)

Tab. 7: Position feedback in normal operation

Software can used to assign in part also other colours and blinking patterns to some display modes – compare

chapter “5.2”.

5.3.2 Feedback in case of Errors / Warnings

If the position feedback in controlled/normal operation and error/warning displays occur at the same time , these are not displayed at all for some display modes or alternately for other display modes – see the following table

(“Tab. 8”) and also the blinking patterns in Tab. 9 (see on the next pages).

Display mode

“Device-specific”

(“8681 Classic”)

NAMUR

Valve mode

Valve mode + errors

Valve mode + errors + warnings

Position feedback yes no yes yes yes

Errors ( E )+ warnings ( W ) yes yes no yes ( E rrors) yes ( E rrors +

W arnings)

Special characteristics alternately:

2 seconds position feedback (see “5.4.2”) /

2 seconds error/warning display (see “5.4.1”)

only device status displays - see chapter “5.2.2”

see chapter “5.2.3” and “5.4.2”

alternately:

1 second position feedback (see “5.4.2”) /

1 second error display – see chapter “5.2.4”

alternately:

1 second position feedback (see “5.4.2”) /

1 second error/warning display – see “5.2.5”

“Fixed colour”

“LED off”

Tab. 8: no no no no

permanently selected colour displaying – see “5.2.6”

no displays

Display behaviour of the different display modes with regard to position, error, warning

17 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

In addition to the position feedback signals, the errors and the device status in the various display modes are also indicated by means of different blinking patterns.

Display of device status / errors / warnings

No.

Blinking pattern / colour

(for reasons of space the

“colour of the valve position” is designated as position colour )

1 in position colour

7 in error colour in position colour in position colour in error colour in error colour in error colour

ON OFF Note

100 ms

125 ms

250 ms

50 ms

450 ms

100 ms

3 x flashing:

Teach-In confirmation

( after successful teaching: colour for position 1 and 2 continuously ON)

100 ms

3 x flashing:

- if target could not be located in the measuring area during teaching or

- if teach position is too close

(±0.5 mm) to a previously defined teach position or

- if magnetic manual override is used, even though manual override function was disabled by software

125 ms

Continuous flashing:

Signal from the external initiator S4

(factory settings – comp.

line 3 in “Tab. 7”)

250 ms

Continuous flashing:

Signal from position 3 (factory settings

– comp. line 2 in “Tab. 7”)

250 ms

450 ms

50 ms

Continuous flashing:

- Teaching does not occur or

- Autotune function error or

- Teach Reset implemented or

- Bus error or

- Position measuring system signal

error (from firmware B.02.00.00) or

- Device Reset implemented

Continuous flashing:

Device in service mode / manual override active

Continuous flashing:

Internal error x x x x x x x x x x x x x x x x x x x x x x x x english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

No.

Blinking pattern / colour

(for reasons of space the

“colour of the valve position” is designated as position colour ) ON OFF Note

8 blue colour (position feedback during OFF phase)

1 sec.

3 sec.

Continuous flashing:

Service/maintenance notification (maintenance / service required)

(Position feedback occurs during OFF phase) x

11 alternately red / green

(500 ms per colour) alternately red / yellow / green

(500 ms per colour)

Continuous flashing:

Device Reset mode active

(for Device Reset press again within

10 s)

Continuous flashing:

Autotune (selection) mode active

(for Autotune function press appropriate keys within 10 s)

Continuous flashing:

Autotune function active x x x alternately red / yellow / green

(200 ms per colour)

Tab. 9: Display behaviour of the different display modes with regard to, error, warning, status

*) These abbreviations mean: Classic – device specific LED mode (8681 Classic Mode X),

NAMUR – NAMUR mode (NAMUR NE 107),

“VM” – v alve m ode,

“VM+E” – v alve m ode with e rror messages,

“VM+E+W” – v alve m ode with e rror and w arning messages x x x x x x x x

5.3.3 Localisation function

This function can be used to localise a device in the system via the control system (e.g. Bürkert Communicator).

When the localization function is activated, the device status LED (Top LED) begin to flash according to the

signal priority (see chapter “5.4”) and according to the following logic (see “Tab. 10”).

In the NAMUR mode, the device status is displayed as “single flashing”.

In the display modes VM+E and VM+E+W, any error or warning messages that may occur are displayed as

“single flashing” in the corresponding color alternating with the corresponding position feedback (S1, S2, S3 or

S4) – see “Tab. 10”.

19 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

No. Blinking pattern

2 every second:

1 x 25 ms ON

Note single flashing: in white: no (taught)

position active in colour from S1 or S2: S1 or S2 active in color of the device status or in the error colour / warning colour alternating with the position feedback signal

(S1, S2, S3, S4), if an error or warning message is present double flashing: in colour from S3: S3 active x x x x x x x x x x x every second:

2 x 25 ms ON

3 triple flashing: in colour from S4: S4 active every second:

3 x 25 ms ON

Tab. 10: Display behaviour during active localisation function

These abbreviations mean: see explanations below Tab. 9 (Page 19).

x x x x

5.4 “Signal priorities” – with reference to the Basic OI for Type 8681

5.4.1 When several states overlap for one valve

In this case the following priority list applies to the “device specific” display mode (“8681 Classic X”) :

1. Internal error: ( error colour: 450 ms ON, 50 ms OFF)

2. Manual operating mode is active, e.g. by magnetic manual override - see chapter “18. Service mode/manual override” ( error colour: 50 ms ON, 450 ms OFF)

3. Other faults, e.g. position measuring system not taught, bus error or other

(see chapter “5.3” of these supplementary operating instructions)

4. Service / maintenance request ( blue colour: 1 s ON, 3 s OFF)

The display logic described in chapter “5.2” applies to the other display modes; this is shown in detail in the

respective subchapters: english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

• “NAMUR” – see chapter “5.2.2”

• “Valve mode” – see chapter “5.2.3”

• “Valve mode + errors” – see chapter “5.2.5”

• “Valve mode + errors + warnings” – see chapter “5.2.5”.

5.4.2 When position feedback overlaps

The following logic is the factory setting for all display modes:

S1 active active

S2 active active

S3 active active active

S4 active active

Error Priority Note / blinking patterns

S4 Flashing in S4 blinking pattern (if S4 activated by DIP) as S3/S4 has priority over S1 and S2

Flashing in S4 blinking pattern if S4 activated by DIP

Flashing in S3 blinking pattern as S3/S4 has priority over S1 and S2 active active S2 Position feedback of S2 has priority

Tab. 11: Display priorities when position feedback overlaps (factory settings)

Factory settings: S4 has the highest priority, descending to S1 (i.e. S4 - S3 - S2 - S1) - this corresponds to

the “PRIO 24” in the following table (”Tab. 12”).

This display logic (described in Tab. 11 above) can be changed via software using the sensor parameter “PRIO

(priority feedback positions)”; the parameter values and the assigned display priority as follows:

Parameter “PRIO” (highest) priority 1

Priority 2

Priority 3

(lowest) priority 4

21 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

Parameter “PRIO” (highest) priority 1

Priority 2

Priority 3

24 *)

particular logic, see “Tab. 13”

Tab. 12: Display priorities when position feedback overlaps - can be selected using parameter “PRIO”

*) Factory settings: “PRIO 24”

(lowest) priority 4

Optical feedback: Display of

Tab. 13: the Top LED

S4 no display

Position feedback

0 all other combinations

Special case: Display priorities when position feedback overlaps (parameter “PRIO” = “25”)

When the position feedback is from S4 (external initiator), note whether the external initiator is an “Opener” (NC contact) or a “Closer” (NO contact). The position feedback signal “0” always means “S4 not active”, the “1” means

“S4 active”.

The factory setting of S4IN (NO - normally open) can be easily changed using the Bürkert Communicator Type

8920, but can be also overwritten with the help of the data from the parameter list - see “6.19.4 Access to further parameters (cyclic and acyclic)”.

22 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

5.5 “Display of the status LEDs for bus error” – with reference to the Basic OI for Type 8681

The following applies to the Control Heads Type 8681 büS/CANopen:

Bus errors are also indicated by the central multi-coloured status display (device status LED / Top LED)- see

chapter “Blinking pattern / fault signalling” (in the Basic Operating Instructions) and “5.3” as well as “5.4”.

Bus errors are indicated by the status LEDs on the electronic module as well as by the

Top LED .

The device status LED (“Module”) and the bus status LED (“Network”) are located on the electronic module of the control head - see figure beside.

Fig. 1: Status LEDs

Function tests for both status LEDs after the power has been switched on (connection of the network cable):

Status LED

“Module”

“Network”

Colour of the LED Function test red / green green / red

250 ms ON (red)

750 ms ON (green)

250 ms ON (red)

250 ms ON (green)

500 ms OFF

Blinking pattern

If the function test has been completed successfully, the status LEDs indicate the device status as described in the following tables:

Status of the device status LED “Module”

LED Device status

OFF No power supply

Explanation

• Device is not powered

Green Device is working • normal operation

Status of bus status LED “Network”

LED

OFF

Green *)

Red/green *) blinking

(500 ms/

500ms

Device status possible errors

• No fault detected or only in bus mode

= “büs” *)

• device start-up phase

• No fault detected *)

• No setpoint connection configured for controlling the solenoid valves *)

(continued on next page)

Remedy

Configure a setpoint connection for controlling the solenoid valves (see

chapter “6.13.3”.

23 english

Type 8681 büS/CANopen

ChangesconcerningbüS/CANopendesign

LED

Red

Device status

Error

- it is critical if the LED is still lit 2 minutes after the last device restart possible errors

• Another device with the same

Node ID is in the same network

• No bus connection (Gateway

/ PLC) due to communication problems or gateway restart

Remedy

• Check baud rate

• Check the Node ID address (if required, correct it so that each address is only available once)

• Check the status of the gateway connected to the system

• If required, replace the device

*) Display/visualization only from firmware version B.02

5.6 Further help

5.6.1 Links to different operating instructions

If you need further help for the configuration of Type 8681 (büS) you can also use further documents.

On the Bürkert website www.burkert.com search for the type number or the device identification number and find the corresponding documents under “Downloads” / “User manuals” (use language filters if necessary):

Operating Instructions Type 8681 | Control Head

Operating Instructions Type ME43 | Fieldbus gateway büS to Industrial Ethernet

For configuration and parameterisation using the Bürkert Communicator, see also:

Software manual Type 8920 | Bürkert Communicator

Software manual | Central configuration management

(Search for type: ME43 / Downloads / User manual)

On the Bürkert website under “Downloads” / “Software” also can be found:

for Type 8681 büS/CANopen, the Object List for CANopen and the corresponding EDS file and

for the gateway, the Parameter List for the respective specific configuration.

To do this, enter the identification or article number of the respective device into the search field, search under

“Downloads” / “Software” the ZIP container with the “Initiation Files”, open it and download the corresponding files.

5.6.2 Firmware updates

Firmware updates of the control heads, gateways (and possibly other devices) can only be carried out using the

Bürkert Communicator with the aid of a büS stick. This requires the “installer level”.

The integration of the Bürkert Communicator into the network can be seen, for example, in “Fig. 2”.

The firmware is stored in the Bürkert Communicator and is kept up to date via updates.

english

Type 8681 büS/CANopen büS/CANopen-Design

6 BÜS/CAN OPEN-DESIGN

6.1 Definition

The “büS” (Bürkert system bus) is a fieldbus system based on the CAN protocol (Controller Area Network).

It enables Bürkert devices to communicate with each other.

The Control Head Type 8681 büS/CANopen is a device which conforms to the specification (see chapter “6.5”).

6.2 Network principle / Interfaces

Fig. 2: Network principle

The PC with the Bürkert Communicator can be connected to each free connection in the büS network, for example to one of the distributors.

The control head can also be connected to the Bürkert-Communicator for individual configuration. This can be done

(depending on the variant) via the M12 plug or via the connection terminal inside the device. In doing so, the control head must also be supplied with power.

Different connection cables and a plug-in power supply unit as well as a mains adapter are included in a small

equipment case (“USB büS interface Set1” - see chapter “7”). This allows to configure also a single device.

25 english

Type 8681 büS/CANopen büS/CANopen-Design

• Each gateway can control up to 63 nodes (Control Heads Type 8681 büS/CANopen) if the network topology considers the max. permitted cable length and the required power supply. Each node requires a unique “Node ID”, otherwise an error occurs.

• The max. total line length is 200 m for 125 kbit/s, 100 m for 250 kbit/s, 40 m for 500 kbit/s.

• The max. cable length for a single drop line is 6 m, the max. total length of all drop lines in the network is 100 m for 125 kbit/s, 55 m for 250 kbit/s, 30 m for 500 kbit/s.

• If the voltage drop is too large, an additional power supply can feed in at a CAN junction box (PWR

IN connection). In this case, connect CAN ONLY to CAN IN using a CAN cable .

This cable (which interconnects the CAN junction boxes at “CAN ONLY” and “CAN IN”) cannot be used for T-connectors to branch “nodes” because no power is supplied to this cable (compare example

3 in chapter “8”).

• Unused or open connections must be closed with the appropriate protective caps.

• Required tightening torque for all plug-in connections (cables, T-pieces, ...) to ensure the required leak-tightness against moisture: 0.6 Nm + 0.1 Nm.

• The CAN cable must be “terminated” at both ends: connect a terminating resistor (120 ohms) to the end of the CAN cable / T-connector or, if the line ends with a CAN junction box, connect the terminating resistor to the CAN OUT connection.

• For service work and also when reading out CAN data, a PC with Bürkert Communicator Type 8920 can be connected to any free connection at the CAN junction box or to the CAN ONLY connection.

A büS stick is necessary to connect the PC to the CAN network.

• T-connectors can be used to connect single “nodes” or a PC to read out the CAN data (via Bürkert

Communicator).

6.3 Gateway

Icon

EDS file for

EtherNet/IP: Gateway_EIP_8681_vxx_yymmdd_63Dev.eds

Icon: icon_me43.ico

The Gateway Type ME43 is used as a fieldbus interface between the Control

Heads Type 8681 (büS) and the PLC (e.g. EtherNet/IP; Profinet on request).

Each gateway is designed to communicate with up to 63 control heads.

Fig. 3: Gateway ME43 with connection terminals

6.4 Electrical connection options

Fig. 4: Connection options

With cable glands

or with cable glands and multi-pole connection

(M12 plug according to IEC 61076-2-101, 5-pole)

Connection left: voltage, signals

Connection right: external initiator

(see also chapter “7 Accessories”)

english

Type 8681 büS/CANopen büS/CANopen-Design

6.5 büS/CANopen specification

6.5.1 General data

Baud rate:

Address:

Bus mode:

configurable via DIP switches 7, 8 or via software (selectable values – see chapter

“6.13.1 Setting the baud rate”)

factory setting: software configurable baud rate (pre-selected: 500 kbit/s)

1 ... 63 (via DIP switches 1 ... 6 adjustable); factory settings: 0 = software configurable address / Node ID

(Node ID from 1 to 127 possible; pre- selection: auto-addressing of the Node ID,

see chapter “6.13.2 Setting the büS/CANopen address (Node ID)”)

büS or CANopen (bus mode is software configurable only) factory setting: büS

Process data: büS/CANopen or e. g. EtherNet/IP (depending on configuration)

6 byte input

1 (...6) byte input

Gateway /

SPS

Gateway /

EtherNet/IP

1 byte output

Outputs:

(Gateway –> control head)

(Configurations for further bus systems on request)

Inputs: 6 byte with:

(Control head –> gateway) 4 byte position feedback in m (resolution: 1 mm)

(= feedback as cyclic position signal of the target),

1 byte NAMUR status feedback signal,

1 byte position feedback (3 discrete feedback signals from the position measuring system (positions S1 to S3) + 1 discrete feedback signal from the external initiator (S4); power supply via büS/CANopen cable (11 ... 25 V DC)

(The acyclic analogue position signal of the target can be read out e.g. as parameter “8681_Current_Position_mm_DevXX” (resolution: 0.1 mm) - see chapter

“6.19 Access to parameters (Read / Write)” on page 50)

1 byte for control of the 3 solenoid valves

6.5.2 Total line length and drop line lengths of the bus cables

The bus line is a 4-core cable with additional shielding which must conform to the büS/CANopen specification. The cable transmits both data/information and energy (low-voltage power supply for actuators and sensors)

The maximum total line length (sum of trunk lines and drop lines) of a network depends on the baud rate.

Some baud rates and their corresponding maximum lengths are listed in the table below.

Baud rate

125 kbit/s

250 kbit/s

500 kbit/s

Max. total line length

200 m

100 m

40 m

Max. length of an individual drop line

6 m

Compare “Fig. 7: Network topology - büS/CANopen” on page 32.

Max. total length of all drop lines

100 m

55 m

30 m

27 english

Type 8681 büS/CANopen büS/CANopen-Design

6.6 Electrical data of the control head

Connections:

Cable gland version: 1 x M16 x 1.5 cable gland / SW22 – for power supply and signals,

(only for transportation safety device sealed with dummy plugs, remove these before use!) for cable diameter 5 ... 10 mm, for wire cross-sections 0.14 ... 1.5 mm 2

1 x M16 x 1.5 cable gland/SW19 - connection option for external initiator

(sealed with dummy plug, remove this before use)

Multipole connection version: 1 x M16 x 1.5 cable gland/SW22 with M12 plug according to IEC 61076-2-

101, 5-pole on a cable 80 cm in length for büS/CANopen and power supply

1 x M16 x 1.5 cable gland/SW19 - connection option for external initiator

(sealed with dummy plug, remove this before use)

Power supply:

Power consumption

(standby current) :

11 … 25 V DC

<60 mA at 24 V DC

Max. power consumption:

<180 mA at 24 V DC (see chapter “6.8”)

Power consumption

(normal operation): <165 mA at 24 V DC (3 solenoid valves active, 1 position feedback with

LED display, no external initiator)

Input / proximity switches (external initiator: S4 in):

Power supply:

Current carrying capacity sensor

supply:

Design:

Short-circuit protection via the büS/CANopen power supply - 10% max. 30 mA

Input current 1 signal:

Input voltage 1 signal: U

Input current 0 signal:

DC 2- and 3-wire,

Normally open contact, PNP output

Sensor

Input voltage 0 signal: U

> 6.5 mA, limited internally to 10 mA

Sensor

> 10 V

< 4 mA

< 5 V

Inputs (from master perspective) / binary or analogue feedback signals:

The recovery of the 3 valve positions reported back in binary format or the analogue position signal is described in the Basic Operating Instructions in the chapter “Position measuring system”. The analogue target position signal

(resolution: 0.1 mm) is available in the büS/CANopen network as an acyclic value / parameter.

Outputs (from master perspective) / solenoid valves:

Typ. switching capacity: 0.9 W (per solenoid valve, for 200 ms after the power has been switched on)

typ. continuous output: 0.6 W (per solenoid valve, from 200 ms after the power has been switched on)

Output reduction:

Typ. pull-in current:

Typ. holding current:

Operating mode:

Valve types: via the büS/CANopen interface - electronics integrated

38 mA or 0.9 W / 200 ms (per solenoid valve)

25 mA or 0.6 W at 24 V DC (per solenoid valve)

Continuous operation (100% duty cycle)

6524

Central display of the switching statuses:

Current consumption from büS/CANopen

at 24 V DC: approx. 30 mA with a power supply of 24 V DC per illuminated display; colour switching see chapter 17. “LED colour assignments” (in the Basic Operating

Instructions) and chapters “5.3” and “5.4”.

english

Type 8681 büS/CANopen büS/CANopen-Design

6.7 Safety position if the bus fails

If the bus fails, the solenoid valve is switched to a programmable safety position (default: solenoid valve de-energised).

For configuration data / parameter see chapter “6.19 Access to parameters (Read / Write)”.

6.8 Design aid

Power consumption of the electronics:

= 1.3 W or

Power consumption of a valve after reduction:

Valve

= 0.6 W or

Valve

= 54 mA at 24 V

Power consumption of a valve during activation (200 ms):

Valve-ON

= 0.9 W or I

Valve-ON

= 38 mA at 24 V

= 25 mA at 24 V

Power consumption of an optical position feedback:

LED

= 0.7 W or I

LED

= 30 mA at 24 V

Calculation examples:

Example 1:

3 valves are activated, one position is reported (state for 200 ms): the control head switches automatically one valve after another to keep the current consumption low - i.e.: max. current consumption I

2 valves (already activated) + 1 valve (just switching)

Total l, max.

= current consumption of

Total

= P

4.1 W

= 1.3 W

+ 2 x P

Valve

+ 2 x 0.6 W

+ 1 x P

Valve-ON

+ 1 x 0.9 W

+ 1 x P

LED

+ 1 x 0.7 W or

Total

@ 24 V = I

172 mA = 54 mA

+ 2 x I

Valve

+ 2 x 25 mA

+ 1 x I

Valve-ON

+ 1 x 38 mA

+ 1 x I

LED

+ 1 x 30 mA

Example 2:

3 valves have been activated, one position is reported (persistent state):

Total

= P

+ 3 x P

Valve

+ 1 x P

LED

3.8 W = 1.3 W + 3 x 0.6 W + 1 x 0.7 W or

Total

@ 24 V = I

159 mA = 54 mA

+ 3 x I

Valve

+ 3 x 25 mA

+ 1 x I

LED

+ 1 x 30 mA

When using an external initiator, its power requirement should be added.

29 english

Type 8681 büS/CANopen büS/CANopen-Design

6.9 Installation – Safety instructions

WARNING!

Risk of injury due to electric shock!

` Before reaching into the system (apart from the teach-in procedure in a non-explosive atmosphere), switch off the voltage and secure to prevent it from being switched on again!

` Observe the applicable accident prevention and safety regulations for electrical equipment!

` When setting the position measuring system (Teach-In), do not touch any live components!

Risk of injury due to improper installation!

` Installation may be carried out by authorised technicians only and with the appropriate tools!

Risk of injury due to unintentional activation of the system and uncontrolled restart!

` Secure system against unintentional activation!

` Following installation, ensure a controlled restart.

The mechanical and pneumatic installation of the control heads is described in detail in the Basic OI.

6.10 Gateway installation

→ Mount the gateway(s) on a top hat rail in the control cabinet

→

Connect the gateway(s) as described in the next chapter and as shown in chapter “6.2 Network principle /

Interfaces”

→ Connect gateway(s) to the master controller (PLC) via for example EtherNet/IP

6.11 Electrical installation - büS/CANopen

For the multipole connection variants:

No internal cabling work is required for any of the “büS” variants (with multipole connection) which makes installation and start-up on site considerably easier and quicker, reducing the risk of leaks.

The control head features a multipole circular plug (M12 x 1, 5-pole, male) to an 80 cm long cable. The assignment conforms to the büS/CANopen specification.

However, you will require the correspondingly assembled cable sets with the pin assignments described below:

View of plug from the front onto the pins:

Pin 4: CAN_H white

Pin 5: CAN_L blue

Pin 1: Drain

(shielding)

Fig. 5: Bus connection büS/CANopen with power supply

Pin 3: V– black

Pin 2: V+ red english

Type 8681 büS/CANopen büS/CANopen-Design

For the versions with cable glands:

→ Open the housing (compare chapter 8 “Opening and closing the housing” in the Basic Operating Instructions

for Type 8681) so that this electronic module is visible as shown below (“Fig. 6”) .

→ Connect the different wires of the CAN cable to the screw terminals for the bus signal as specified in the table

“Terminal strip configuration”. The configuration conforms to the büS/CANopen specification.

→

The order numbers of the required CAN cables are listed in chapter “7 Accessories”

6.11.1 Electronic module büS/CANopen:

Teach-In buttons T1-3

Solenoid valve connection with status LED for Valve 1

DIP switches for setting address and baud rate

Status LED for device

Status LED for network

Power supply büS/CANopen

Bus signals

Fig. 6: Electronic module büS/CANopen

Service interface

DIP switches for colour coding the Top LED (for more details see

“5.2”)

Solenoid valve connections with status LED for Valves 2, 3

Connection of the external initiator

6.11.2 Terminal strip configuration:

Designation

Terminal strip

V+

Wire colour red

Assignment

V-

CAN_H black white

Power supply büS/CANopen

Bus signal CAN high

Designation

Terminal strip

Assignment

V +

S4 IN

Power supply for external initiator

External initiator input

GND GND external initiator

CAN_L blue Bus signal CAN low

For connecting the external initiator - compare Basic Operating Instructions, chapter “Connection of an external initiator”.

31 english

Type 8681 büS/CANopen büS/CANopen-Design

6.11.3 Details on the DIP switches for colour coding:

The (classic) colour combinations can be set via DIP 1 to 4 as described in the Basic Operating Instruction, chapter

“Setting the colour combinations”. But on this occasion DIP 5 and DIP 6 have to be set to “OFF” to display the correct colours.

As of firmware B.02.00.00 there are software configurable display modes for the device status LED (Top LED) – details

are specified in chapter “5.2”.

Other parameters or configurations require the use of the CANopen object list or parameter list - see “6.19.4 Access to further parameters (cyclic and acyclic)”.

6.12 Network topology of a büS

CANopen system

When installing a büS/CANopen system, ensure that the terminating circuit of the data lines is correct. The circuit prevents the occurrence of interference caused by signal reflection in the data lines.

The trunk line must be terminated at both ends with 120 Ω

resistors and 1/4 W power loss - see “Fig. 7: Network topology - büS/CANopen”.

“Fig. 7” illustrates a line with one trunk line and several drop lines. Trunk lines and drop lines consist of identical

material.

A unique Node ID (büS/CANopen address) can be allocated to each control head via DIP switches - see chapter

“6.13 Configuring the Node ID / baud rate”).

Trunk line büS/CANopen cable

V +

V –

CAN_H

CAN_L

Terminating resistor

120 Ω

¼ W

Node 01

Drop lines büS/CANopen cable, max. 6 m long

Node n

Terminating resistor

120 Ω

¼ W

Control head 1 (node 1)

Fig. 7: Network topology - büS/CANopen

Control head n (node n)

32 english

Type 8681 büS/CANopen büS/CANopen-Design

6.13 Configuring the Node ID / baud rate

DIP switches for address+ baud rate

8 DIP switches are available for configuration:

• DIP switches 1 to 6 for the Node ID (büS/

CANopen address)

• DIP switches 7 to 8 for the baud rate

Please note:

Values fixed by DIP switches invalidate softwareconfigured values!

DIP switches for colour configuration

Fig. 8: Position of the DIP switches

6.13.1 Setting the baud rate

Adjustment of the control head to the baud rate of the network:

Baud rate

125 kbit/s

250 kbit/s

500 kbit/s

Factory settings: software configurable baud rate *) with pre-setting: 500 kbit/s

DIP 7 DIP 8 off on off on off off on on

*) Via software (Bürkert Communicator) configurable baud rates: 50, 125, 250, 500, 1000 kbit/s; via software (CANopen/SPS) additionally configurable baud rates: 10, 20, 100 kbit/s

(see chapter “6.19.4 Access to further parameters (cyclic and acyclic)”).

Please note: The baud rate of all network participants (control heads, gateway, possibly other products) must correspond to each other!

To apply any changes to settings, restart the device!

If the settings are changed by actuating the DIP switches, these changes will not take effect until the device is restarted! For a restart:

• trigger a restart command via Bürkert Communicator or

• briefly disconnect the control head from the power supply and reconnect or

• switch the power supply off/on or

• transmit an appropriate reset message.

Special characteristics for configuration of the “software configurable baud rate”:

• Hardware configured values (via DIP switch) have priority over software configured values!

• If the DIP switches were set to “software configurable baud rate”, the current baud rate is still valid - until a new baud rate is selected via software. Then restart the device!

Example: Resetting the factory setting without using the software:

Set DIP7+8 to 500 kbit/s. Restart device. Then set DIP7+8 to “software configurable”. Restart device.

33 english

Type 8681 büS/CANopen büS/CANopen-Design

6.13.2 Setting the büS/CANopen address (Node ID)

Node ID = [DIP 1 ⋅ 2 0 + DIP 2 ⋅ 2 1 + DIP 3 ⋅ 2 2 + DIP 4 ⋅ 2 3 + DIP 5 ⋅ 2 4 + DIP 6 ⋅ 2 5 ]

with DIP x = off = 0 and DIP x = on =1

Table of settings of the büS/CANopen address:

0 *)

Node ID DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 off off on on off off off on on on off off on on on off off on on on on on off off off off off off on on on on on off off off off on off on off off on off on on off on off on on off on off on off on on off on off off off off off off off on off on off on off off on on off off on off off off on on on off off off off off off off off off off off off off off off off off off off on on off off on on off off off on on on on on on on on on on on on on on on on on on off off off off on off off off off on on on on on off on on on on on on on on on on on on off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off on off on on off on off off on off on off off on off on on off on off on on off on off off on off off on off on off on on off on on off off off on on off off off on on on off off on on on off off on off off on off off on on

Node ID DIP1 DIP2 DIP3 DIP4 DIP5 DIP6

35 on on on off off off on on on on on off off off off off off on on on on on off off off on on on off off off off on on on on on on on off off off off on off off off off on on on on on off on on on off off off off off off off on on on on on on on on on on on on on on on on off off off off off off off off off off off off off off off off on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on

To apply any changes to settings, restart the device!

(See NOTE box 1 on next page for restarting)

*) This is the factory setting. (For explanations see NOTE box 2 on next page)

For easy start-up when using a preconfigured gateway, a node ID between 1 and 63 should be set on the device using the DIP switches. Otherwise, a device configuration on site via Bürkert Communicator is required for start-up. english

Type 8681 büS/CANopen büS/CANopen-Design

NOTE 1: How to restart the device

If the settings are changed by actuating the DIP switches, these changes will not take effect until the device is restarted! For a restart:

• trigger a restart command via Bürkert Communicator or

• briefly disconnect the control head from the power supply and reconnect or

• switch the power supply off/on or

• transmit an appropriate reset message.

NOTE 2: Special characteristics for the DIP switch setting DIP1 to DIP6 “000000”

• This setting is the factory setting, i.e. software configurable address/Node ID.

The further behavior in the network depends on the “Static Node-ID”, see for this the following explana tions.

• Bus mode büS (bueS) or CANopen:

The behaviour with this DIP switch setting depends on the bus mode (büS (bueS) or CANopen).

The factory setting is büS (bueS). The bus mode can be changed by software only - see chapter

“6.19.4 Access to further parameters (cyclic and acyclic)”.

• Device addressing using software in the: büS/bueS mode: For the DIP switch position (DIP1 to DIP6 = 000000) the parameter “Fixed

CANopen address” (“Static Node ID”) has a factory setting of “0” = “Auto addressing” of the device address (CANopen address, Node ID). On this occasion, the Node ID will be automatically configured (device addresses from

1 to 127 are possible).

If the device is to receive a fixed device address, the “Fixed CANopen address”

(“Static Node ID”) must be set to the appropriate value using the Bürkert

Communicator. To accept this value, the device must be restarted. If the device does not receive the “target” device address set as parameter ”Fixed CANopen address” , the solenoid valves remain in the configured safety position and an error status is displayed.

If the “Fixed CANopen address” (“Static Node ID”) is reset to “0” (= “Auto addressing”), the auto addressing starts after a restart with the last used device address (Node ID).

When changing the configuration of the device address from “via DIP switch” to

“software configured”, the “Fixed CANopen address” (“Static Node-ID”) is reset once to “0” (= “Auto addressing”) at the required restart. Auto addressing starts a usual after a restart with the last used device address (Node ID) .

In the case of auto addressing, the interfaces of the individual devices have to be checked and possibly reassigned, e.g. via Bürkert Communicator – see operating

instructions Type 8920 (“büS network configuration”/”büS map”), see “5.6.1”.

CANopen mode: Software configurable device address / Node ID (from 1 to 127 is possible):

Consider for CANopen bus mode that a software configured Node ID of “0” results in a device Node ID of “1”! But if two devices had the same address, bus problems would result!

Please note: Hardware-configured values (that means: set via DIP switches) overwrite software-configured values!

35 english

Type 8681 büS/CANopen büS/CANopen-Design

NOTE 3: Special characteristics for the DIP switch setting different to DIP1 to DIP6 “000000” , i.e. hardware configured Node ID

• Bus mode büS (bueS) or CANopen:

The behaviour with this DIP switch setting depends on the bus mode (büS (bueS) or CANopen).

The factory setting is büS (bueS).

The bus mode can be changed by software only - see chapter

“6.19.4 Access to further parameters (cyclic and acyclic)”.

• Device addressing using DIP switches in the: büS (bueS) mode: The parameter “Fixed CANopen address” (“Static Node ID”) is automatically updated to the address value currently set via DIP switches when a restart occurs.

The parameter “Fixed CANopen address” (“Static Node-ID”) is automatically updated to the address value currently set via DIP switches after a restart.

In this mode, the device is prepared at the factory for the use with a preconfigured gateway, i.e. the input connection for controlling the solenoid valves has already been configured.

Details are clarified in chapter “6.13.3”.

CANopen mode: The device address (Node ID) is used which is set via DIP switches.

6.13.3 Factory settings of the control head regarding the gateway configuration

Factory settings:

Bus mode: “büS”,

Addressing: software configurable Node ID

(i.e. DIP1 to DIP6 = 000000 ) - see details in NOTE box 2 above.

If DIP1 to DIP6 differ from the factory setting:

This means: if DIP1 to DIP6 > 000000 (device address fixed by DIP switches - see NOTE box 3) and the DIP switch position was changed after the last device restart, the control heads will be configured according to a preset rule at the next device restart. This automatically configures the setpoint producer for the control ofthe solenoid valves. The factory default setting is defined: “Presetting Rule” = “1” for systems with a preconfigured gateway

(“Gateway_8681”). This results in an automatic adaptation according to the node ID (>0, set via the DIP switches) of the respective control head.

From firmware version B.02.00 onwards, it is possible to change the (preconfigured) setpoint producer via “büS-

Map” with the Bürkert Communicator for e.g. a standard büS system (without preconfigured gateway).

Changing the DIP switches to a value > 000000 and then restarting the device will overwrite any changes made via the Bürkert Communicator with values according to the preset “presetting rule”. This presetting rule is defined by the parameter “presetting rule” (“Use Special Sensor Index”) which can be found in the Bürkert Communicator under: Control Head / General Settings / Parameters / Presettings büS mapping.

When returning to the factory default setting ( with fixed device address ), after changing the presetting:

- ensure that the parameter “presetting rule” is set to “1”

- note the previous DIP switches position

- set DIP1 to DIP6 to factory default setting 000000, then restart the device

- set DIP1 to DIP6 to the noted DIP switches position, then restart the device again.

Details on the büS network configuration (“büS map”) are described in the operating instructions for the Bürkert

Communicator (Type 8920 - see chapter “5.6.1”).

english

Type 8681 büS/CANopen büS/CANopen-Design

6.13.4 Central configuration management (Configuration client)

As of firmware B.01.00.00 the central configuration management (e.g. with gateway ME43, as of firmware A.03.02) is supported. This means that defective Bürkert devices can be exchanged easily, almost without configuration effort.

To do this, the configuration management for the configuration provider (gateway) in the Bürkert Communicator must be set to “Active” and the “ Configuration client ” parameter for the configuration device (control head) must be set to mode “Automatically switch on” (= factory setting) or “Active” (Bürkert Communicator: Control Head / General settings / Parameters / Configuration client / Mode).

Via a memory card in the ME43 gateway, the last stored device parameters and configurations are retained and can be transferred to the new Bürkert device.

When replacing a defective control head, however, the hardware settings (all DIP switches) must be set on the new device before connecting to the network, as they have been set on the device which is to be replaced. In this way, all relevant software parameters (during the communication process lasting several minutes to integrate the new control head into the network) can be transferred automatically. The new device must then be taught-in.

Details and operating conditions are described in the software manual “Central configuration management of

Bürkert devices” (see chapter “5.6”).

For this configuration the Bürkert Communicator version 4.x or higher is required.

(During a device reset / factory reset of the configuration device (control head, as of firmware B.01.00.00), the

“configuration client” parameter mode is reset to the factory setting “Automatically switch on”.)

6.14 Changing the gateway IP address

Each gateway requires a unique IP address to distinguish several gateways from each other.

If required, the gateway IP address can be changed directly at the gateway itself using its menu and arrow keys or in four other ways: using web server

(“6.14.1”) or

Bürkert Communicator

(“6.14.2”) or

Logix Designer

(“6.14.3”, please use the

LogixDesigner manual for this) or RS Linx

(“6.14.4”)

After changing the gateway IP address, register and install the gateway using Logix Designer (“6.15”) (see

“6.16”).

The gateway must always be connected to the same network as the PC!

6.14.1 Changing the gateway IP address using web server

→ Call the gateway’s web server with a browser (enter only the current IP address number:

“http://192.168.1.100” )

(the window which opens for this IP address shows the default

“Static IP address” of all gateways ME43

(factory setting): 192.168.1.100

)

→ Then click “Login”

37 english

→ Complete the “User name” and “User password”

(factory setting for both: “admin”)

→ Click the “Login” button

→ Change/overwrite the “Static IP address”, e.g. with “192.168.1.101” or another address, to distinguish the gateways from each other

→ Confirm by clicking the “Apply” button

(If the button “Restart” is clicked, the new

“Static IP address” is not saved, only the device will be restarted.)

→ Click the “OK” button to take over the new

“Static IP address” by restarting the device

(if “Cancel” is selected, the old “Static IP address” remains active and is only taken over at the next restart)

→ The following message appears

→ To connect the gateway to its new IP address: enter the new IP address (shown in the figure above) into the browser address bar and press “Enter” english

Type 8681 büS/CANopen büS/CANopen-Design

6.14.2 Changing the gateway IP address using “Bürkert

Communicator”

→ Connect the PC (with Bürkert Communicator Type 8920) via “büS stick” to the büS/CANopen data line

(e.g. to a free connection of a CAN junction box in the network - as shown in “Fig. 2: Network principle”)

→ Start the Bürkert Communicator Type 8920

→ Click on the icon to add a “büS connection” (e.g. “büS COM8”)

→ Open the desired gateway (e.g. “Gateway_8681”) and select

“Parameter” tab, then select “Protocol settings”

“Industrial communication” and then the

→ The standard address “Static IP address” is displayed (“192.168.1.100”)

→ Click the pencil to change the IP address

→ Confirm the new “Static IP address” by clicking on the “Apply” button

→ Restart the device / gateway: Right click on “Gateway_8681”, then select the “Restart” option english

Type 8681 büS/CANopen büS/CANopen-Design

6.14.3 Changing the gateway IP address via Logix Designer

→ Start the “Logix Designer”

→ First, select “Go Online”

(“Rem Run” = Remote Run)

→ Right click on “Ethernet”

→ Select “Gateway 8681 bues ...”

→ Right click and select “Properties”

→ A new window opens, go to the

“Internet Protocol” tab

→ Mark “Manually configure IP settings” (in the area “Internet Protocol

Settings”)

→ In the area “IP Settings Configuration”, overwrite the current

“Physical Module IP Address” and

- if required - also “Subnet Mask” and “Gateway Address”

→ Click the “Set” button.

A warning then appears:

“IP Address in physical module does not match address in general properties (...)”

→ Click the “OK” button english

Type 8681 büS/CANopen büS/CANopen-Design

→ Then select “Go Offline”

→ Go to the “General” tab

→ Overwrite the “Ethernet Address”/

“Private Network” with the new address

→ Click the “OK” button

→ Select “Go Online” again

→ A new window opens

→ Go to the “Options” tab

→ Click the “Download” button to load the offline changes of the project into the controller / PLC

(continued on next page) english

→ A new window with several warnings opens

→ Click the “Download” button to continue the download process

Type 8681 büS/CANopen büS/CANopen-Design

42 english

Type 8681 büS/CANopen büS/CANopen-Design

6.14.4 Changing the gateway IP address using RS Linx

→ Start “RS Linx”

→ Select “Autobrowse”

→ Right click on “AB_ETHIP-1,

Ethernet”

→ Select “XXX, Gateway 8681 bueS ...”

→ Right click on “XXX, Gateway

8681 bueS ...” and select “Module

Configuration”

→ A new window opens, go to the “Port

Configuration” tab

→ In the area “Network Configuration

Type”, mark the “Static” option

→ Enter the new “IP Address” and - if required - also the “Subnet Mask” and “Gateway Address”

→ Confirm the configuration with “OK”

→ A warning window opens

→ Click “Ja” (Yes) button to continue the changing process

Inaccessible IP addresses are crossed out english

Type 8681 büS/CANopen büS/CANopen-Design

6.15 Registration of a gateway via Logix Designer

The gateway ME43 must be registered in the Logix Designer database:

→ Ensure that the EDS file and the ICO file are in the same folder

( Do not change the name of the ICO file as it is referenced in the EDS file with this name!)

→ Start the “Logix Designer”

→ Go to the “Tools” tab

→ Select “EDS Hardware Installation Tool”

→ A new window opens as shown in the figure on the right

→ Select “Register an EDS file(s)” option and click the “Next” button

→ A new window opens as shown in the figure on the right

→ Select “Register a single file” option

→ Browse your computer for the appropriate

EDS file:

“Gateway_EIP_8681_vXX_

YYMMDD_63Dev.eds”

→ Click the “Next” button (twice)

→ A new window opens: “Change Graphic

Image”

→ If you want to change the icon graphic, click the “Change icon ...” button and select a graphic

→ Click the “Next” button (twice)

→ Then click the “Finish” button

The gateway ME43 is now registered in the

Logix Designer database. english

Type 8681 büS/CANopen büS/CANopen-Design

6.16 Installation of a gateway via Logix Designer

Gateway(s) must be added to the Ethernet (I/O Configuration):

→ Start the “Logix Designer”

→ First, go “Offline”

→ Search for “I/O Configuration” and “Ethernet”

→ Right click on “Ethernet”

→ Select “New Module”

→ In the new window “Select Module Type”, select the appropriate device from the

“Catalogue”:

(use the filter function for a faster search: vendor “Buerkert Werke ...”)

→ After selecting the “Gateway 8681 bueS”, click on the “Create” button

(continued on next page) english

→ In the new window “New Module”, enter a new significant name in the name field and select the appropriate “Private

Network” number for the “Ethernet

Address”

→ Click on “OK” button

→ Close the (old) window “Select Module

Type”

→ in the new window DOWNLOAD the cor-

responding files (see chapter “6.3”) onto

the PLC

→ Then “Go Online” to connect the gateway and the master controller / PLC (EtherNet/

IP) to each other

Type 8681 büS/CANopen büS/CANopen-Design

46 english

Type 8681 büS/CANopen büS/CANopen-Design

6.17 Configuration of the control head network

The gateway Type ME43 is used as a fieldbus interface between the control heads (Type 8681 büS/CANopen) and the master controller (EtherNet/IP). Each gateway can communicate with up to 63 control heads of Type 8681 büS/

CANopen.

To set up a network, it is necessary to assign a unique device address to each control head (to do so,

use the respective DIP switches - see chapter “6.13.2”).

If there are less than 63 control heads connected to a gateway, it is necessary to “hide” the nonexisting control heads, namely both the inputs and the outputs.

There are 2 options to “hide” the inputs and outputs:

via software “Logix Designer” (“6.17.1”) or via the “Bürkert Communicator” Type 8920 (“6.17.2”).

6.17.1 “Hide function” via software “Logix Designer”

→ Start the “Logix Designer”

→ Open the project (e.g. “Logix Designer - Gateway_Type8681”)

→ Open the desired gateway and select the “Parameters” tab

→ Now select the line “Hide Outputs 1-64” and “hide” each non-existent control head by setting a “1” (one) in each field for the outputs.

→ Now select the line “Hide Inputs 1-64” and “hide” each non-existent control head by setting a “1” (one) in each field for the inputs.

→ Click on the “Set” button to save it and to transfer it to the gateway

→ After doing these steps, restart the whole system: it is recommended to switch off and switch on the corresponding power supply unit! The network configuration has then been completed.

47 english

Type 8681 büS/CANopen büS/CANopen-Design

6.17.2 “Hide function” via “Bürkert Communicator”

→ Connect the PC (with Bürkert Communicator Type 8920) via “büS stick” to the büS/CANopen data line (e.g.

to a free connection of a CAN junction box in the same network - as shown in “Fig. 2: Network principle”)

→ Start the Bürkert Communicator Type 8920

→ Click on the icon to add an interface (e.g. “büS COM8”)

→ Open the desired gateway (e.g. “Gateway_8681”) and select “Industrial communication” and then the

“Parameter” tab, search for “Hide process values”, then select “Edit hide objects” and start the step sequence with a click

→ “Page 1” : Start the “hiding function”: set the switch to set the switch to

(ON) in order to reset already hidden values – or

(OFF) in order to NOT reset already hidden values.

→ Click on “Next” (or cancel the “hiding process” via button “Cancel”).

english

Type 8681 büS/CANopen büS/CANopen-Design

→ “Page 2” : Hiding of the outputs: set the switch to set the switch to

(ON) in order to activate the hiding, i.e. these outputs are hidden then – or

(OFF) in order NOT to activate the hiding, i.e. these outputs are NOT hidden:

→ Click on “Next” (or cancel the “hiding process” via button “Cancel”).

→ “Page 3” : Hiding of the inputs: set the switch to set the switch to

(ON) in order to activate the hiding, i.e. these inputs are hidden then – or

(OFF) in order NOT to activate the hiding, i.e. these inputs are NOT hidden: :

→ Click on “Next” (or cancel the “hiding process” via button “Cancel”).

→ “Page 4” : Finish the “hiding function”: set the switch to (ON): newly hidden values will be confirmed and with “Finish” the device will be restarted immediately – or set the switch to (OFF): newly hidden values will be confirmed, but with “Finish” the device is NOT restarted immediately (the newly set values are accepted after the next restart) – or cancel the execution of the “hiding function” with button “Cancel” (so the new settings will be discarded).

49 english

Type 8681 büS/CANopen büS/CANopen-Design

6.18 Description of the (cyclical) I/O data

Gateway /

SPS

6 byte

Process data

1 byte

Depending on the configuration, the gateway processes

1 ... 6 byte of the process data emanating from the control head for the position feedback of the position measuring system.

1 byte process data regarding the solenoid valve switching states are processed by the control head.

For process data, see also chapter “6.5” on page 27

The relevant process data are transfered via Logix Designer as “Controller Tags”: the (position) feedback signals from S1 ... S4 (bit-coded, see example 1 below) and the current position feedback signals (“analog”) as well as the solenoid valve switching states V1 ... V3 (bit-coded, see example 2 below)

Example 1 (process data from control head to gateway/PLC):

“Position 1” and “External Initiator” are active:

Example 2 (process data from PLC/gateway to the control head):

“Valve 1” is active:

6.19 Access to parameters (Read / Write)

Some relevant acyclic parameters have been defined for preconfigured gateways which can be read directly with the Logix Designer

and partially overwritten - described below in chapters “6.19.1 Parameter – reading via Logix

Designer” and “6.19.2 Parameters – writing via Logix Designer”.

The Bürkert Communicator (Type 8920) also makes it easy to read out the parameters and change the values

(see “6.19.3 Access to parameters via Bürkert Communicator” or in the manual for the Bürkert Communicator -

see chapter “5.6.1” on page 24).

In addition to these relevant acyclic parameters, further values and states for acyclic parameters of the büS devices

connected to the gateway can be read out and partially written/overwritten - see “6.19.4 Access to further parameters (cyclic and acyclic)”.

english

Type 8681 büS/CANopen büS/CANopen-Design

6.19.1 Parameter – reading via Logix Designer

→ Open the project (e.g. “Logix Designer - Gateway_Type8681”)

→ According to the path (I/O Configuration / Ethernet / Gateway ...), open the desired gateway and select the “Parameters” tab. In “Group” select <All Parameters>, all relevant predefined parameters are displayed for each control head (scroll down to see the data of the other control heads).

NOTE!

EDS with other predefined parameters available on request.

But o n e parameter for all control heads can also be displayed using the “Group” function:

→ E.g. select the (Parameter) “Group” / “TP1 negative” ( = Feedback Field Teach Position 1 negative):

T h i s parameter is displayed for all devices: (see next page) english

Type 8681 büS/CANopen büS/CANopen-Design

6.19.2 Parameters – writing via Logix Designer

Parameters in white fields (rw) can be overwritten (parameters in grey fields (ro) can only be read out):

→ Open the desired gateway as for the reading function and in the “Parameters” tab select e.g. Group: “All

Parameters”

In order to type in or change a value in a white field:

→ Type in a value in the white “Value” field, considering the data type as specified under “Style” (if no style is specified, it is a string value, in that case click the symbol to type in).

→ Press the button “OK or “Enter” to accept the value english

Type 8681 büS/CANopen büS/CANopen-Design

6.19.3 Access to parameters via Bürkert Communicator

The Bürkert Communicator (Type 8920) makes it easy to read and change parameters. For a detailed description

of the Bürkert Communicator - see the relevant manual (see chapter “5.6.1” on page 24).

→ Connect the PC (with Bürkert Communicator Type 8920) to the büS/CANopen data line using the “büS stick”; start Bürkert Communicator Type 8920

→ Click on the icon to add an interface (e.g. “büS COM8”)

→ Select the desired device in the navigation bar (left), open the “Parameter” tab ( for special values also

“Diagnostics” or “Maintenance”) , search for the desired value/parameter and read it out or change:

→ Current parameter values can be read out directly at the right margin;

Parameters with a pen symbol can be overwritten with the appropriate authorisation or step sequences can be started.

→ A restart is required after a factory reset and in order to activate changes of bus/communication settings.

6.19.4 Access to further parameters (cyclic and acyclic)

In addition to the predefined relevant parameters, further values can be read out and partially overwritten. Access is via “Bürkert Communicator” or e.g. via Logix Designer.

The required fieldbus addresses (as well as indices / sub-indices) are shown in a Parameter list that corresponds to the respective gateway configuration. This parameter list and other files can be found on the Bürkert website - enter the respective ID number of the preconfigured gateway as search term and download the required files from the ZIP container under “Downloads” / “Software”.

An Object list for CANopen and other required files for the Type 8681 büS/CANopen can be found on the Bürkert website – enter the type “8681” or the ID number of the device as search term and download the corresponding files after opening the ZIP container with the “Initiation Files”, found under “Downloads” / “Software”.

53 english

Type 8681 büS/CANopen

Accessories

7 ACCESSORIES

CAUTION!

Risk of injury and/or damage due to the use of unsuitable parts

Incorrect accessories and unsuitable spare parts may cause injuries and damage the device and the surrounding area.

` Use only original accessories and original spare parts from Bürkert.

Accessories Figure Order / ID no.

Switching power supply Type 1573 to power the CAN sub-system

(Note: only ID no. 772898 conforms to NEC Class 2

(all ID no. of Type 1573 conform to the EU standards 2014/35/EU - LVD and 2014/30/EU - EMC)

3.8 A nominal output current

(conforms to “NEC Class 2”)

772898

1 A nominal output current 772361

2 A nominal output current 772362

10 A nominal output current 772698

Gateway ME43 (also an SD card for the gateway)

(connection between büS/CANopen (Bürkert) and Ethernet/IP (Rockwell Automation));

316696

(gateway) preconfigured and designed for the connection/control of up to 63 Control Heads Type 8681 (büS)

774087

(SD card)

Other pre-configurations e.g. in conjunction with Control

Heads Type 8691, Positioners Type 8692 or Process Controllers Type 8693 on request.

Cables and connections (büS/CANopen) developed for application in environments with “hygienic requirements”

(degree of protection: IP65/67 | materials: Metal parts - stainless steel, cable sheath - PVC | U = 24 V DC,

I = max. 4 A; required tightening torque for the required leak-tightness against moisture: 0.6 Nm + 0.1 Nm )

Connection cable with flying leads and M12 plug *) , length 1 m

(for the connection of büS control heads with cable glands)

218187

Connection cable with flying leads and M12 socket *) , length 1 m

Connection cable with flying leads and M12 socket *) , length 3 m

Extension cable, M12 plug + M12 socket *) , length 0.5 m

Extension cable, M12 plug + M12 socket *) , length 1 m

Extension cable, M12 plug + M12 socket *) , length 3 m

Extension cable, M12 plug + M12 socket *) , length 5 m

Extension cable, M12 plug + M12 socket *) , length 10 m

Extension cable, M12 plug + M12 socket *) , length 20 m

773482

773483

773484

773485

773486

773487

773488

773489 english

Type 8681 büS/CANopen

Accessories

Accessories

CAN terminating resistor, M12 plug *) , 120 Ω

CAN terminating resistor, M12 socket *) , 120 Ω

CAN Y-connector, M12 *)

Figure Order / ID no.

773490

773491

773492

CAN T-connector, M12 *)

Mounting plate for CAN T-connector (M12)

773493

773494

Protective cap for M12 socket for closing unnecessary (open) connections

(10 protective caps per pack)

Protective cap for M12 plug including O-ring 8 x 2 N-NBR 70

(10 caps and 10 O-rings per pack) for closing unnecessary (open) connections

CAN junction box, M12 *) for connection up to 8 devices to the bus

(6 connections have already been closed with appropriate protective caps)

308778

308785

338398

*) Required tightening torque for all plug-in connections (cables, T-pieces, ...) to ensure the required leaktightness against moisture: 0.6 Nm + 0.1 Nm.

Alternatively, DeviceNet cabling components (e.g. from Rockwell Automation) can also be used. However, they must comply with the necessary requirements when used in the “Hygenic area”, because not all of these parts have the required quality such as stainless steel or PP or PPE or PVC.

Service tool

USB büS interface set:

büS standard set (büS stick + 0.7 m cable with M12 plug)

büS adapter for büS service interface (M12 on büS service interface Micro-USB)

büS cable extensions from M12 plug to M12 socket (not for “hygienic requirements”)

Extension cable, length 1 m

Extension cable, length 3 m

Extension cable, length 5 m

Extension cable, length 10 m

Equipment case “USB-büS-Interface Set1”

Order / ID no.

772551