T2535T-8T
Datasheet
25 A - 800 V - T-series Triac in TO-220AB
A2
A2
G
A1
TO-220AB
A1
A2
G
Product status link
T2535T-8T
Product summary
I
T(RMS)
V
DRM
, V
RRM
V
DSM
, V
RSM
I
GT
25 A
800 V
900 V
35 mA
Features
• 25 A medium current Triac
• 150 °C maximum junction temperature T
J
• Surge capability V
DSM
, V
RSM
= 900 V
• Three triggering quadrants
• High noise immunity - static dV/dt
• Robust dynamic turn-off commutation - (dI/dt)c
• ECOPACK2 compliant component
Applications
• General purpose AC line load control
• AC induction and universal motor control
• Heating: water heater, e-bidet
• Power tools
• Cooker, oven
• Lighting and automation I/O control
• Inrush current limiting circuits
• Overvoltage crowbar protection
Description
The T2535T-8T Triac in TO-220AB can be used for the on/off or phase angle control function in general purpose AC switching.
Based on the ST Snubberless technology, it offers higher specified turn-off commutation and noise immunity levels up to 150 °C.
The T2535T-8T safely optimizes the control of the motors and heaters loads for the most constraining home appliances environments.
DS13450 - Rev 1 - September 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1
T2535T-8T
Characteristics
Characteristics
V
DRM
/
V
RRM
V
DSM
/
V
RSM
I
GM p
GM
P
G(AV)
T stg
T j
T
L
Table 1. Absolute maximum ratings (limiting values)
Symbol
I
T(RMS)
RMS on-state current (full sine wave)
Parameter
I
TSM
I 2 t dl/dt
Non repetitive surge peak on-state current (full cycle, T j
initial = 25 °C)
I 2 t value for fusing
Critical rate of rise of on-state current, I
G
= 2 x I
GT
, tr ≤ 100 ns, f = 100 Hz
Repetitive peak off-state voltage
T c
= 121 °C t = 16.7 ms t = 20 ms t p
= 10 ms f = 120 Hz
T j
= 125 °C
T j
= 150 °C
Non Repetitive peak off-state voltage
Peak gate current
Maximum gate power dissipation
Average gate power dissipation
Storage temperature range
Operating junction temperature range
Maximum lead temperature for soldering during 10 s t p
= 10 ms t p
= 20 µs t p
= 20 μs
T j
= 25 °C
T j
= 150 °C
T j
= 150 °C
T j
= 150 °C
900
4
5
1
-40 to +150
-40 to +150
260
Value
25
210
200
264
100
800
600
Unit
A
A
A 2 s
A/µs
V
V
A
W
W
°C
°C
°C
Symbol
I
GT
V
GT
V
GD
I
L
I
H
(1) dV/dt (1)
Table 2. Electrical characteristics (T j
= 25 °C, unless otherwise specified)
Test conditions Quadrants
V
D
= 12 V, R
L
= 30 Ω
V
D
= V
DRM
, R
L
= 3.3 kΩ, T j
= 150 °C
I
G
= 1.2 x I
GT
I
T
= 500 mA, gate open
V
D
= 536 V, gate open
V
D
= 402 V, gate open
(dl/dt)c
(1)
Without snubber network
I - II - III
I - II - III
I - III
II
T j
= 125 °C
T j
= 150 °C
T j
= 125 °C
T j
= 150 °C
Min.
Min.
Min.
Min.
Min.
Max.
Max.
Min.
Max.
Max.
Max.
Value
5
35
1
0.15
50
80
35
1500
1000
28
18
1. For both polarities of A2 referenced to A1.
Unit mA mA
V/µs
V/µs
A/ms
A/ms
V
V mA
DS13450 - Rev 1 page 2/11
T2535T-8T
Characteristics
Symbol
V
TM
(1)
V
TO
(1)
R
D
(1)
I
T
= 35 A, t p
= 380 µs
Threshold voltage
Dynamic resistance
V
D
= V
R
= 800 V, peak voltage
I
DRM
/I
RRM
V
D
= V
R
= 600 V, peak voltage
V
D
= V
R
= 400 V, peak voltage
1. For both polarities of A2 referenced to A1.
Table 3. Static characteristics
Test conditions
T j
= 25 °C
T j
= 150 °C
T j
= 150 °C
T j
= 25 °C
T j
= 125 °C
T j
= 150 °C
T j
= 150 °C
Value Unit
Max.
1.5
V
V Max.
0.80
Max.
Max.
Max.
Max.
5
6
17
5
5 mΩ
µA mA mA
Symbol
R th(j-c)
R th(j-a)
Table 4. Thermal resistance
Parameter
Junction to case (AC)
Junction to ambient
Max.
Typ.
Value
1
60
Unit
°C/W
DS13450 - Rev 1 page 3/11
T2535T-8T
Characteristics (curves)
1.1
Characteristics (curves)
Figure 1. Maximum power dissipation versus on-state
RMS current (full cycle)
Figure 2. On-state RMS current versus case temperature
(full cycle)
35
30
25
20
15
10
5
0
P(W)
0
α = 180 °
5
I
T(RMS)
(A)
10 15 20 25
30
I
T(RMS)
(A)
25
20
15
10
5
0
0 25
α = 180°
50
T c
(°C)
75 100 125 150
Figure 3. On-state RMS current versus ambient temperature (free air convection)
3.5
I
T(RMS)
(A)
3
2.5
2
1.5
1
0.5
0
0 25
α = 180 °
50
T a
(°C)
75 100 125 150
Figure 4. On-state characteristics (maximum)
1000
I
TM
(A)
100
T j
= 150°C
T j
R
D max.
V
TO
= 0.8 V
= 17 mΩ
10 T j
= 25°C
1
0 0.5
1 1.5
2 2.5
3 3.5
V
TM
(V)
4 4.5
DS13450 - Rev 1 page 4/11
T2535T-8T
Characteristics (curves)
Figure 5. Relative variation of I
GT
,I
H
, I
L
vs junction temperature (typical values)
2.5
I
GT
, I
H
, I
L
[T j
] / I
GT
, I
H
, I
L
[T j
= 25 ° C]
2.0
I
GT
1.5
1.0
I
H
& I
L
0.5
0.0
-40 -20 0 20 4 0
T j
(°C)
60 80 100 120 140 160
Figure 6. Relative variation of critical rate of decrease of main current versus junction temperature
5
4
3
2
7
6
8
(dI/dt) c
[T j
] / (dI/dt) c
[T j
= 150°C]
1
0
25 50 75
T j
(°C)
100 125 150
Figure 7. Relative variation of critical rate of decrease of current (dI/dt)c versus reapplied (dV/dt)c
Figure 8. Surge peak on-state current versus number of cycles
2.0
(dI/dt) c
[ (dV/dt) c
] / specified (dI/dt) c typical values
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.1
1.0
(dV/dt)
C
(V/µs)
10.0
100.0
250
I
TSM
(A)
200
150
100
50
0
1
Repetitive
T c
= 121°C
10
Number of cycles
100
T
Non repetitive j initial = 25°C
1000
Figure 9. Non repetitive surge peak on-state current for a sinusoidal pulse width t
P
< 10 ms
Figure 10. Relative variation of thermal impedance versus pulse duration
10000
I
TSM
(A) dI/dt limitation: 100 A/µs
Tj initial=25 °C
1.0E+00
K=[Z th
/R th
]
Z th(j-c)
Z th(j-a)
1.0E-01
1000
I
TSM
1.0E-02
100
0.01
0.10
1.00
t
P
(ms)
10.00
t
P
(s)
1.0E-03
1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03
DS13450 - Rev 1 page 5/11
T2535T-8T
Characteristics (curves)
Figure 11. Leakage current versus junction temperature for different values of blocking voltage (typical values)
1.0E+04
I
DRM
/I
RRM
(µA)
1.0E+03
1.0E+02
1.0E+01
1.0E+00
1.0E-01
50
V V
D
=V
75
DRM
V =V =V
T j
(°C)
100
V
D
125 150
DS13450 - Rev 1 page 6/11
2
2.1
T2535T-8T
Package information
Package information
•
•
•
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
TO-220AB package information
Molding compound resin is halogen free and meets UL94 flammability standard, level V0
Lead-free plating package leads
Recommended torque: 0.4 to 0.6 N·m
Figure 12. TO-220AB package outline
DS13450 - Rev 1 page 7/11
DS13450 - Rev 1
T2535T-8T
TO-220AB package information
Table 5. TO-220AB package mechanical data
Dimensions
Ref.
e
F
I
L
I2
I3
I4
M b1 b2
C c1 c2
A a1 a2
B
Min.
15.20
2.40
6.20
3.73
2.65
1.14
1.14
15.80
13.00
10.00
0.61
1.23
4.40
0.49
2.40
Millimeters
Typ.
3.75
16.40
2.6
1. Inch dimensions are for reference only.
Max.
15.90
2.70
6.60
3.88
2.95
1.70
1.70
16.80
14.00
10.40
0.88
1.32
4.60
0.70
2.72
Min.
0.5984
0.0945
0.2441
0.1469
0.1043
0.0449
0.0449
0.6220
0.5118
0.3937
0.0240
0.0484
0.1732
0.0193
0.0945
Inches (1)
Typ.
0.1476
0.6457
0.1024
Max.
0.6260
0.1063
0.2598
0.1528
0.1161
0.0669
0.0669
0.6614
0.5512
0.4094
0.0346
0.0520
0.1811
0.0276
0.1071
page 8/11
3
T2535T-8T
Ordering information
Ordering information
Figure 13. Ordering information scheme
T 25 35 T - 8 T
Triac series
RMS current
25 = 25 A
Gate triggering current
35 = 35 mA
High temperature
T = T series
Voltage
8 = 800 V
Package
T =TO-220AB
Order code
T2535T-8T
Marking
T2535T-8T
Table 6. Ordering information
Package
TO-220AB
Weight
2.1 g
Base Qty.
50
Delivery mode
Tube
DS13450 - Rev 1 page 9/11
Revision history
Date
23-Sep-2020
Version
1
Table 7. Document revision history
Changes
Initial release.
T2535T-8T
DS13450 - Rev 1 page 10/11
T2535T-8T
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved
DS13450 - Rev 1 page 11/11
