P0102DA
Datasheet
0.8 A 400 V high immunity sensitive SCR thyristor in TO-92
A
G
K
TO-92
K
G
A
Product status link
P0102DA
Product summary
I
T(RMS)
V
DRM
/V
RRM
I
GT
T j max.
0.8 A
400 V
0.2 mA
125 °C
Features
• On-state rms current, I
T(RMS)
0.8 A
• 125 °C max. T j
• Low 0.2 mA gate current
• Repetitive peak off-state voltage, V
DRM/VRRM
400 V
• ECOPACK2 compliant
Applications
• Gate driver for large Thyristors
• Overvoltage crowbar protection
• Ground fault circuit interrupters
• Arc fault circuit interrupter
• Standby mode power supplies
• Residual current detector
Description
Thanks to highly sensitive triggering levels, the 0.8 A P0102DA SCR thyristor is suitable for all applications where available gate current is limited.
This device offers a high blocking voltage of 400 V, ideal for applications like interrupters circuits.
The P0102DA is available in through-hole TO-92 package.
DS13119 - Rev 2 - May 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1
P0102DA
Characteristics
Characteristics
Table 1. Absolute maximum ratings (limiting values)
Symbol
I
T(RMS)
I
T(AV)
Parameters
On-state RMS current (180° conduction angle)
Average on-state current (180° conduction angle)
I
TSM
I 2 t dl/dt
V
DRM
/ V
RRM
I
GM
P
G(AV)
T stg
T j
Non repetitive surge peak on-state current,
T j
initial = 25 °C
I 2 t value for fusing
Critical rate of rise of on-state current
I
G
= 2 x I
GT
, t r
≤ 100 ns
Repetitive peak off-state voltage
Peak gate current
Average gate power dissipation
Storage junction temperature range
Operating junction temperature range t p
= 8.3 ms t p
= 10 ms t p
= 10 ms
F = 60 Hz t p
= 20 µs
T
L
= 55 °C
T j
= 25 °C
T j
= 25 °C
T j
= 25 °C
T j
= 125 °C
T j
= 125 °C
T j
= 125 °C
Value
0.8
0.5
8
7
0.24
Unit
A
A
A
50
400
1
0.1
-40 to +150
-40 to +125
A 2 s
A/µs
W
°C
°C
V
A
Symbol
I
GT
V
GT
V
GD
V
RG
I
H
I
L dV/dt
Table 2. Electrical characteristics (T j
= 25 °C, unless otherwise specified)
Parameters
V
D
= 12 V, R
L
= 33 Ω
V
D
= V
DRM
, R
L
= 3.3 kΩ, R
GK
= 1 kΩ, T j
= 125 °C
I
RG
= 10 µA
I
T
= 50 mA, R
GK
= 1 kΩ
I
G
= 1.2 I
GT
, R
GK
= 1 kΩ
V
D
= 67 % V
DRM
, R
GK
= 1 kΩ, T j
= 125 °C
Value Unit
Max.
200 µA
Max.
0.8
Min.
Min.
0.1
8
V
V
Max.
Max.
Min.
5
6
75 mA mA
V/µs
Symbol
V
T
V
TO
R d
I
DRM
I
RRM
Table 3. Static electrical characteristics
Test conditions
I
TM
= 1.6 A, t p
= 380 µs
Threshold on-state voltage
Dynamic resistance
V
D
= V
DRM
V
R
= V
RRM
T j
Value
25 °C Max.
1.95
125 °C Max.
0.95
Unit
V
V
125 °C Max.
600
25 °C
125 °C
Max.
1
0.1
mΩ
µA mA
DS13119 - Rev 2 page 2/9
Symbol
R th(j-l)
R th(j-a)
Junction to lead (DC)
Junction to ambient (DC)
Table 4. Thermal resistance
Parameters
P0102DA
Characteristics
Max.
value
80
150
Unit
°C/W
DS13119 - Rev 2 page 3/9
P0102DA
Characteristics (curves)
1.1
Characteristics (curves)
Figure 1. Maximum power dissipation versus on-state
RMS current (full cycle)
1.0
P(W)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.0
α = 180°
0.1
0.2
I T(AV) (A)
0.3
0.4
α
0.5
360°
0.6
Figure 2. Average and DC on-state current versus lead temperature
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0
I
T(AV)
(A)
25
D.C. (TO-92)
α = 180° (TO-92)
50
T lead
(°C)
75 100 125
Figure 3. Average and DC on-state current versus ambient temperature
Figure 4. Relative variation of thermal impedance versus pulse duration
I
T(AV)
(A)
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0
D.C. (TO-92)
α = 180° (TO-92)
2 5 5 0
T amb
(°C)
7 5 100 125
1.00
K=[Z th(j-a)
/R th(j-a)
]
0.10
0.01
1E-2 1E-1 1E+0
TO-92
1E+1 1E+2 5E+2
Figure 5. Relative variation of holding current versus gate-cathode resistance
20
I [ R GK ] / I [ R GK = 1 k Ω]
18
16
14
12
10
8
6
4
2
0
1E-2 1E-1
Typical values
R GK Ω
1E+0
T j
= 25°C
1E+1
Figure 6. Relative variation of gate voltage and gate, holding and latching current versus junction temperature
6.0
I
GT
, V
GT
, I
H
, I
L
[T j
] / I
GT
, V
GT
, I
H
, I
L
[T j
=25 ° C]
5.0
4.0
3.0
IGT
2.0
(R
I
H
GK and I
L
=1 KΩ)
1.0
V
GT
0.0
-40 -20 0 20 40 60 80
Relative variations
Typical values
100 120 140
DS13119 - Rev 2 page 4/9
P0102DA
Characteristics (curves)
Figure 7. Relative variation of static dV/dt immunity versus gate-cathode resistance
10.0
dV/dt[R GK ] / dV/dt[ R GK
D
T j
= 125°C
V = 0.67 x V
DRM
1.0
Typical values
0.1
0 0.2
0.4
0.6
0.8
R
GK
Ω
1.0
1.2
1.4
1.6
1.8
2.0
Figure 8. Relative variation of dV/dt immunity versus gatecathode capacitance
10 dV/dt[C
GK
] / dV/dt[ R
GK
V = 0.67 xV
T j
= 125°C
R = 1k
DRM
Ω
8
6
4
Typical values
2
0
C
GK
(nF)
0 1 2 3 4 5 6 7
Figure 9. Surge peak on-state current versus number of cycles
Figure 10. Non-repetitive surge peak on-state current for sinusoidal pulse (t p
< 10 ms)
8
I
TSM
(A)
7
6
5
4
3
2
1
0
1
Repetitive
T amb
= 36 °C
Non repetitive
T initial = 25°C
1 0
Number of cycles
100
One cycle
1000
100.0
ITSM(A)
10.0
1.0
0.1
0.01
0.10
1.00
I
TSM
10.00
Figure 11. On-state characteristics (maximum values)
1E+1
I TM (A)
T max.:
V = 0.95 V
Ω
1E+0
T j
= max Maximum values
1E-1
1E-2
0.5
1.0
1.5
2.0
V
TM
(V)
2.5
3.0
3.5
4.0
4.5
DS13119 - Rev 2 page 5/9
2
2.1
Package information
•
•
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
TO-92 package information
Lead free plating + halogen-free molding resin
Epoxy meets UL94, V0
Figure 12. TO-92 package outline c
P0102DA
Package information
A
B C a b
F D E
Table 5. TO-92 package mechanical data
Dimensions
Ref.
Min.
Millimeters
Typ.
1.35
a b c
E
F
A
B
C
D 4.40
12.70
2.54
1.27
1. Inches dimensions given for information
Max.
4.70
3.70
0.50
0.48
Min.
0.1732
0.5000
Inches (1)
Typ.
0.0531
0.1000
0.0500
Max.
0.1850
0.1457
0.0197
0.0189
DS13119 - Rev 2 page 6/9
3
P0102DA
Ordering information
Ordering information
Figure 13. Ordering information scheme
P01 02 D A - xxxx
Sensitive
P01 = sensitive SCR, high immunity
Gate sensitivity
02 = 200 µA
Voltage
D = 400 V
Package
A = TO-92
Order code
P0102DA 1AA3
P0102DA 2AL3
P0102DA 5AL3
Packing mode
1AA3 = Bag
2AL3 = Ammopack
5AL3 = Tape and reel 13 inch
Marking
P0102 DA
Table 6. Ordering information
Package
TO-92
Weight
0.22 g
Base qty.
2500
2000
2000
Delivery mode
Bag
AMMOPACK not in dry bag
Tape and reel 13"
DS13119 - Rev 2 page 7/9
Revision history
Date
14-Oct-2019
18-May-2020
Revision
1
2
Table 7. Document revision history
Changes
Initial release.
Updated Section Cover image
.
P0102DA
DS13119 - Rev 2 page 8/9
P0102DA
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved
DS13119 - Rev 2 page 9/9
