advertisement
▼
Scroll to page 2
of
4
Woodpeckers” PHENOLIC ROUTER TABLE OWNER: MANUAL Two sizes are available of the Woodpeckers Phenolic Router Table, 24" x 32" nominal and 27" x 43" nominal. Both tables are 3/4" thick with a low friction, wear resistant surface on each face. These router tables are not affected by humidity, heat or even water. Each table is pre-drilled with threaded holes for attaching to our steel router table stands. (Router Table Stand #RTS2027 fits the #RT2432-PH Router Table and the #RTS2037 fits the #RT2743-PH Router Table.) The router plate opening is 9-1/4" x 11-3/4" by just over 3/8" deep with 3/4" radius corners making it compatible with most standard router mounting plates and lifts. The opening itself is offset from the front edge by 13" for the 24" x 32" router table and 16-1/2" for the 27" x 43" table. In each case you'll have plenty of room for maneuvering raised panels, case work, molding and any other routing projects. If you think you're missing anything, email us at [email protected]. You can also call us at 800-752-0725 from 9:00 a.m. to 5:00 p.m. EST Monday - Friday. Oval Nuts 1/4-20 x 1/2" Flathead Machine Screws STEP 1 - Install Fence Track | 1. Two pieces of Fence Track are included with your Phenolic Router Table. The Fence Tracks fit into the machined recesses with the rounded end. Figure 1. Place an Oval Nut, smooth side down, aligned with one of the holes in the machined recess. From underneath the table, insert a Flathead Machine Screw through the table and thread loosely onto the Oval Nut. Repeat for all holes in each recess. Figure 2 T-slot side of the N Fence Track \ N facing up. Fence Track \ 2. With the single T-slot side of the Fence Track facing UP Figure 2a, slide a Fence Track into the recess making sure that the Oval Nuts slip into the two bottom T-slots Figure 2b. lighten the six Flathead Machine Screws. Repeat for the other piece of Fence Track. Ñ Oval Nuts & A Flathead Machine Screws i Woodpeckers® Figure 3 Combo Track T-slot side of the ets Combo Track facing DOWN. 7, Figure 3a ts Le ES р 7. STEP 2 - Install Combo Track 3. One piece of Combo Track is included with your Phenolic Router Table. The Combo Track fits into the machined recess that runs the length of the Phenolic Router Table. Figure 3a. Oval Nuts & Flathead Machine Screws Place an Oval Nut, smooth side down, aligned with one of the holes in the machined recess. From underneath the table, insert a Flathead Machine Screws through the table and thread loosely onto the Oval Nut. Repeat for all holes in the recess. 4, With the single T-slot side of the Combo Track facing DOWN Figure 3, slide the Combo Track into the recess making sure that the Oval Nuts slip into the bottom T-slot. Tighten all Flathead Machine Screws. STEP 3 - Attaching to a Router Table Stand 5. The Woodpeckers Phenolic Router e e Table easily attaches to the Woodpeckers À 10-24x 1/2" Steel router table | TE] Machine Screws stand. The bottom of | the table is pre-drilled SEE oy Figure 4 and tapped for 10-24 x 2" Machine Screws. Figure 4. For other brands of stands or a shop built stand drill & tap the Phenolic Router Table as needed, being careful not to drill completely through the table. 800-752-0725 - woodpeck.com i REVO61820 Woodpeckers PRECISION WOODWORKING TOOLS Woodpeckers, Inc. Strongsville, Ohio - 800-752-0725 - woodpeck.com © 2020 Woodpeckers, Inc. California Proposition 65 WARNING: This product may contain one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
advertisement