Tech Lighting Exo 6 Dual Flush Mount Instructions
Add to My manuals4 Pages
Tech Lighting Exo 6 Dual Flush Mount is an adjustable lighting fixture suitable for damp locations. It can be dimmed using low-voltage electronic dimmers, 0-10V dimmers, or TRIAC dimmers. The fixture is designed to be installed using NEC compliant junction boxes and uses minimum 90°C supply conductors. The installation process involves removing the fixture screws, mounting the plate to the electrical box, connecting the fixture to a suitable ground, and connecting the wires. The LED housing can be rotated to the desired position by squeezing the two tabs on the sides.
advertisement
![Tech Lighting Exo 6 Dual Flush Mount Instructions | Manualzz Tech Lighting Exo 6 Dual Flush Mount Instructions | Manualzz](http://s1.manualzz.com/store/data/066750526_1-6fa4c148bdd90fca1230523bdeba1c7a-360x466.png)
Installation Instructions for
Exo Dual Flush Mount
920FMEXOD
700FMEXOD_
FLUSH
G P I :
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product is suitable for damp locations.
This product can be dimmed with a low-voltage electronic dimmer, 0-10V dimmer or TRIAC dimmer.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°C supply conductors.
SAVE THESE INSTRUCTIONS!
1A
2
MOUNTING PLATE
1B
ELECTRICAL BOX
3
3
1 1
MOUNTING
PLATE
#8-32 SCREW
FIXTURE
SCREW
ALLEN
WRENCH
FIXTURE HOUSING
1 Remove the fixture screws located on both sides of the fixture housing using the provided Allen wrench.
2
Remove the mounting plate from the fixture base.
3 Secure the mounting plate to the electrical box with the two #8-32 screws provided.
1
1C
Install the Fixture
2A
2 3
4
ANCHOR
ANCHOR
4 Line up an anchor with the center of a backplate hole and push the anchor in up to the threads.
5 Screw the anchor the rest of the way in with a screwdriver.
1D
6 Secure the backplate to the anchor with a screw and washer.
7 Repeat steps 4-6 for the remaining anchor hole.
1
Connect the fixture to a suitable ground in accordance with local electrical codes.
2 Connect the black driver wires to the hot power line wire with a wire nut.
3 Connect the white driver wires to the neutral power line wire with a wire nut.
4 For 0-10V dimming, use the purple and gray/pink wires to connect to a compatible dimmer. Keep wires capped if not in use.
5 Place all wires and wire nut connections inside the fixture base.
6 Reinstall the fixture housing to the mounting plate using the fixture screws (reversal of step 1A).
2
Adjust the Module
3A
Optics and Lenses
4A
LENS
OPTIC
LED HOUSING
COVER
WARNING: Always squeeze the two tabs when adjusting the LED housing. Failure to do so will damage the finish.
1 Squeeze the LED housing tabs and rotate the housing to the desired position.
LED
1
2
3
Unscrew and remove the
Remove the optic.
LED housing cover.
If installing an optional lens, rest the lens inside the housing cover.
4 Install the optic (replacement or existing) inside the LED housing cover.
5
Screw the LED housing cover back on.
3
©2022 Tech Lighting, L.L.C. All rights reserved. The Tech Lighting logo is a registered trademark of Tech Lighting.
Tech Lighting reserves the right to change specifications for product improvements without notification.
4
7400 Linder Ave., Skokie, IL 60077
T 847.410.4400 | F 847.410.4500
www.techlighting.com
advertisement