advertisement
▼
Scroll to page 2
5. Seat legs Attach two seat legs to each seat as shown using 2 x 60mm bolt per leg. Secure each bolt using a 6mm washer and 6mm nut. Push 1 x 80mm bolt through the hole in the centre of the top of the seat and secure using an 8mm washer and 8mm nut. Position a leg brace between each set of legs. Secure through the pre- drilled holes in the legs into the ends of the brace using 4 x 70mm screws per brace. Secure the brace to the frames using 2 x 70mm screws per brace. 8mm Washer 8mm Nut Important Note: Only hand tighten the nuts until all bolts are in place, then tighten with a socket/spanner. 60mm 6mm Washer 70mm 6mm Nut English SS306B Round Picnic Bench Assembly Instructions Before assembly •We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction sheet is only a guide to the assembly. Certain items may not be shown to scale. •Check all components prior to assembly •This product should be assembled by no less than two people •Drill all components where indicated 70mm x2 drill Biocidal Products Regulation EU 528/2012 Wolmanit® CX treated wood is a treated article that incorporates biocidal products: copper hydroxide carbonate/II/ and boric acid. They protect wood against fungal decay /rot/ and insect attack. Keep away from food, drink and animal feeding stuffs. Avoid breathing dust when cutting treated wood. 80mm Recommended tools for assembly 70mm • Socket set or spanner 6. Tighten all bolts To finish the assembly tighten all bolts and turn the table over • Safety information IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY Periodically check all fastenings for tightness For contract and domestic use If in doubt of any aspect regarding the assembly, use or safety of your Picnic Bench please contact us : Help Line: (Normal Office Hours) 01829 261 121 Email: [email protected] ROWLINSON GARDEN PRODUCTS LIMITED Green Lane Wardle Nr. Nantwich Cheshire CW5 6BN www.rowgar.co.uk We constantly improve the quality of our products, occasionally the components may differ from the components shown and are only correct at time of printing. We reserve the right to change the specification of our products without prior notice. 2015 © Rowlinson Garden Products Ltd • 10mm Socket/spanner • 13mm Socket/spanner Power drill/screwdriver • Cross head screwdriver bit No. 1 2 3 4 5 6 7 Components Frame with centre block Frame Table top support Table top Seat Seat legs Leg brace Qty. 4 4 4 1 4 8 4 No. 8 9 10 11 12 13 14 15 16 17 18 19 Fixing kit Angle brackets 100mm (M8) bolt 90mm (M8) bolt 80mm (M8) bolt 60mm (M8) bolt 60mm (M6) bolt 8mm dome nut 8mm nut 6mm nut 8mm washer 6mm washer 70mm screws Qty. 4 8 16 4 8 16 32 12 16 28 16 24 4 5 3 7 1 6 2 1. Frame assembly 3. Table top Position the frames as shown. Ensure the angled end of each frame are all facing down. Into each corner position an angle bracket. Using 8 x 100mm bolts, push the bolts first through a bracket then the frames and through the bracket on the other side and secure each one with an 8mm nuts and 8mm dome nut. For ease of assembly only hand tighten the nuts until all bolts are in place. Lay the table top upside down on a soft surface to avoid scratching the top. Turn over the frame and leg assembly and position centrally onto the table top. Secure the table supports to the table using 2 x M8 60mm bolts per leg. Secure each bolt with an 8mm washer and an 8mm dome nut. Important Note: Only hand tighten the nuts until all bolts are in place, then tighten with a socket/spanner. Angled end on each frame must face down. Important Note: Only hand tighten the nuts until all bolts are in place, then tighten with a socket/spanner. 8mm Nut 8mm Dome nut 100mm 8mm Dome nut 8mm Washer 60mm 4. seats With the assembly still upside down, attach the four seats. Insert the middle seat bearer between the frames as shown. Align the holes and secure using 2 x 90mm bolts per seat, secure each bolt with an 8mm washer and 8mm dome nut. 2. Table top supports Important Note: Only hand tighten the nuts until all bolts are in place, then tighten with a socket/spanner. Slide a table top support into the centre of each frame, with the top of the leg angled towards the centre of the assembly. Align the holes on the frames with the holes in the legs and secure using 2 x 90mm bolts per support. Push a bolt through each hole, and secure with an 8mm washer and an 8mm dome nut. Only hand tighten the nuts at this stage. 8mm Washer Important Note: Only hand tighten the nuts until all bolts are in place, then tighten with a socket/spanner. 8mm Dome nut 90mm 8mm Dome nut 8mm Washer 90mm
advertisement