RIGA RIGAIISKHD II Shelf Kit Use and Care Manual
RIGA RIGAIISKHD is a greenhouse construction system, designed to create a controlled environment for growing plants. It features:
- Aluminum frame for durability and corrosion resistance.
- Glazing with UV protection to ensure optimal light conditions for plant growth.
- Adjustable roof windows for ventilation and temperature regulation.
- Customizable size and shape to suit different needs and available space.
- Easy assembly process with clear instructions and all necessary hardware included.
- Strong and stable construction that can withstand strong winds.
- Versatility for growing a variety of plants, including vegetables, flowers, and potted plants.
Advertisement
Advertisement
ALUMINIUM
GREENHOUSE
Riga S/Riga
Subject to technical changes!
Current as of 0 5/2019
Basic kit assembly instructions
Please watch our animated assembly video on our Exaco
Trading Co YouTube
Channel!
https://tinyurl.com/y3yketdy
model Riga
system width 2,96 m / 9ft 8in
model Riga S
system width 2,32 m / 7ft 8in www.exaco.com
877-760-8500
Dear garden friend,
Congratulations on the purchase of an aluminium greenhouse made by
The construction is simple. First, read all the assembly instructions then follow them step by step.
Parts and parts list
Please store all boxes in a dry area protected from direct sunlight!
Quantity of cartons basic construction
(gable/eaves) curved center profile windows/ doors glazing
Riga S/II/III/IV
Riga III/IV/V
Start with the box labeled "basic kit". Please do not open all the boxes at the same time. This will prevent confusing the parts.
Before you begin assembly of a section check the parts list for that box and make sure all parts are present. Parts lists are provided in every box. The boxes go through a quality check before they are closed, thus missing parts are rare. Should any parts be missing please call the customer service number below.
Customer Service: 877-760-8500 or 5 2-407-8500 customerservice @Exaco.com
Exaco Trading
0203 Metropolitan Dr.
Austin, TX 78758
Location
Choose, if possible, a sunny place for your greenhouse. Avoid the shadows of buildings and trees. For vegetables, like tomatoes, cucumbers and melons, position your greenhouse the most north-south as possible. For flowers and potted plant , position in the east-west-direction.
Warning:
The greenhouse should preferably be built in a sheltered spot and not during stormy weather. It is dangerous to leave a partly assembled house!
If assembled correctly this greenhouse resists strong winds. The manufacturer assumes no responsibility for any damage by improper installation or acts of nature.
The construction of the greenhouse must be conducted by at least two people.
Work with secure, craft-oriented tools. Be careful when assembling and make sure your ladder is secure.
In principle work only with gloves (risk of injury, average risk!).
2
For the configuration you need the following tools:
pc. Phillips screwdriver size 2
pc. 10mm Wrench
pc. 3mm allen key (included in the accessoires bag of the roof window)
pc. level
pc. stepladder
1 pc. file to remove any burrs on the profil
pc. rubber hammer
pc. tape measure
You should be careful:
Wedge seals (V23)
Pull them apart at the center.
If forgotten, hexagonal screws can also be inserted later in the plastic slider!
The plastic slider is located in the bottom of the door frame, side and roof bars.
Push the seal 3 - 5 mm between the soil profile and the glazing
Both inside the greenhouse!
Important: Compress the seals when you install them as they contract in cold weather
Quantity of wedge seals
3 - 5 mm 3 - 5 mm 6 - 8 mm 3 - 5 mm 3 - 5 mm 6 - 8 mm length model
Riga S II
Riga S III
Riga S IV
7 2 mm 768 mm
4
4
4
030 mm
7
4 model
Riga III
Riga IV
Riga V length
768 mm 030 mm
4
4
4
030 mm
4
6 pos.
-5-6
pos.
-5-4 pos.
-5-4
pos.
-9
pos.3-3
pos.
-8
pos.
-5-6
pos.4-
pos.4-2
pos.3-2
pos.
-
pos.
-9
pos.2-
3
!!!Note: Important information for glazing!!!
When installing the polycarbonate glazing make sure the UV coated side faces out.
Loosen the edges of the protective film for installation. After the assembly is complete pull it off immediately. Do not leave the film on for any period of time in the sunlight.
Several days of sunlight can burn the film firmly on th e glazing.
Do not
pull the film off right out of the box, otherwise you cannot tell which side has the
UV protection!
Suggestion : If you plan on disassembling and moving you should mark the UV side of each panel before installation. A small circle in a lower corner with a permanent marker will work well.
Question: Does the greenhouse glazing need to be completely sealed?
In principle: No .
We recommend that you seal the horizontal transitions where the glazing meets the aluminum profiles with a neutral cure transparent silicone. (Shown in the diagram below by dashed lines.) This will prevent water and dirt from entering the glazing slots.
Advantage: The greenhouse stays looking new as the seal prevents the formation of algae and buildup of dirt/dust inside the glazing.
During some weather conditions condensation can occur within the hollow chambers of the glazing. This is because the glazing chambers are not air tight. The condensation is purely aesthetic and cannot be avoided.
The condensation/water vapor will not damage the glazing, even at freezing temperatures.
Warning: Use only neutral cure silicone, otherwise it may lead to stress cracks in plastic glazing. This is the most common silicone sealant.
Neutral cure silicone is available in most hardware stores. We recommend Boss 399.
You can purchased Boss 399 directly from us, just call 1-877-760-8500.
Cleaning and care:
To wash the greenhouse use plenty of water, a car wash brush and a little detergent.
4
Foundation frame (optional)
!!!Warning: Use only according to instructions. See below!!!
This is the easiest and the safest foundation for a greenhouse.
ATTENTION! When using a foundation frame attach it to the soil profile before these steps (see pages 5, 6)
The foundation frame hooks into the soil profile and the corners are bolted together with a corner angle (V26). (See page 6). Use the supplied self taping screws to firmly attach the soil profile to the foundation frame.
Setting up the foundation frame
Dig a small ditch 4-5 inches deep in the dimensions of the foundation frame.
Use paving stones or gravel under the horizontal sections as much as possible to prevent the potential for the greenhouse to sag. Fill in the rest of the ditch with earth.
It is also very practical to install tile or stone flooring, this prevents the mud from splashing on the greenhouse during heavy rain.
In addition it makes work easier around the greenhouse, such as mowing the lawn.
Profiles and accesso
ri
es for foundation frame Riga S:
overview pos. description
6.
6.2
foundation frame profile gable foundation frame profile eaves item no 9999 0078 number/length in mm type II type III type IV
2
2 99
2
2033
4
05
2
2 99
2
309
4
05
2
4
2
2
4
99
49
05
0
35
0
35
0
35
S 2
S item no 9999 0267 hexagonal screw M6 x 2 + nut M6 item no 9999 0 24 + 9999 0 28
20 20 20
Profiles and accesso
ri
es for foundation frame Riga :
( V26/V27/S2/S as above) overview pos. description
6.
foundation frame profile gable number/length in mm type III type IV type V
2
2835
2
309 4
2
2835
2
49
2
2835
2
5207
5
Assembly foundation frame
Note: The foundation frame profiles are shorter than soil profiles
Rotate the foundation frame profile into the soil profile. Make sure it is centered in the soil profile.
N ote: The foundation frame profiles are shorter than soil profiles
To stabilize the greenhouse, use the mounting bracket (V27) with bolts M6 x 2 (S2)
Bolt the (V27) to the foundation frame and the side curves or door frames.
Use the supplied self tapping screws to firmly attach the soil profile to the foundation frame.
In the foundation frame corners use two M6 x
2 bolts (S2) and one corner bracket (V26)
Fasten them with two M6 nuts (S).
Foundation of the greenhouse
We recommend that you use anchor bolts to secure the soil profile to your foundation. to The anchor bolts are not included.
side profile/ door frame mounting bracket
- offset - (V 5) bolt M6 x 2 (S 2)
+ nut M6 (S ) soil profil
6
7 soil profile corner V9) of the greenhouse to use as a template to create a stone or concrete foundation. Make sure the corners are square. This will prevent any errors in measurement. frost-free ground
Main box Contents - basic kit Riga S/Riga
Please check contents list to make sure all items are there
Profiles for both gables:
overview pos.
description
.
soil profile/gable
.5.4
Edge curve left
.5.6
Edge curve right
.8
door frame top
.9 cross bar left and right
II
2
2238
2 number/length in mm
Riga S
III
2
2238
IV
2
2238
III
2
2874
Riga
IV
2
2874
2 2 2 2
V
2
2874
2
2
2
876
2
876
2
758
2
2
876
2
876
2
758
2
2
876
2
876
2
758
2
2
2059
2
2059
2
758
2
2
2059
2
2059
2
758
758 758 758 758 758 758
4
702
4
702
4
702
4
020
4
020
4
020
2
2
2059
2
2059
2
758
Profiles for eaves:
overview pos.
description
2.
soil profile/eave
2.3 Side curve
3.2 cross bar/roof window
3.3 ridge profil
3.4 angle stabilization
II
2
2072 number/length in mm
Riga S
III IV III
Riga
IV
2
3 30
2
4 88
2
3 30
2
4 88
2 4 6 4 6
020 020
2
020 020
2
020
V
2
5246
8
4
020
2 37 3 95 4253 3 95 4253 53
4
2 04 3
4
62
4
4220 3
4
62
4
4220
4
5278
8
Accessories bag basic kit Riga S/Riga
overview number
Riga S
4 num ber
Riga
4
-
V9 Soil profile corner item no 9999 0003
V5 connecting plate item no 9999 0028
V 0 connecting plate 90 x 35 mm item no 9999 0030
V endplate ridge/gutter item no 9999 0075
Edge Clamp/Door Frame
For mounting cross bar/rear
4
2
4
2
V4 connecting plate item no 9999 003 for cross bar/roof window
2
II = 2
III = 2
IV= 4
2
III = 2
IV = 4
V = 8
V 2 corner
5 mm item no 9999 0072
S2 blind plug Ø 0 mm item no 9999 0097
V4 door hose section 760 mm lg.
item no 9999 0 8 soil profil screw the corner from inside
Edge profile-drilling cross bar door threshold seal
V23 wedge seal 3 - 5 mm
S9
4,2 x 3 item no 9999 0 9 self-tapping screw pan head item no 9999 0 44 sealing the soil profile insid door frame-soil profile cover plate/corner (V 2)
S 3 self-tapping screw pan head item no 9999 0 50 gable
S5/
S hexagnal screw M6 x 6
+ nut item no 9999 0 83 + 9999 0 28 screws for pulling
V 5 mounting bracket - offset item no 9999 0207 for the attachement of the greenhouse to a foundation made by customer (not with foundation frame)
4
4
See table below !
38*
6
See table below!
38*
II = 40*
III = 40*
IV = 44*
III = 40*
IV = 44*
V = 48*
0
4
4
6
0
S32 washer A6,4
V item no 9999 0 73 mounting corner bracket inside item no 9999 00074 door frames, roof and side profiles
20 je
2x lks.
2x rts.
20
V = 24 je
2x lks.
2x rts.
9
Assembly procedure gable
ATTENTION!
When using a foundation frame attach it to soil profile in advance (see pages 5, 6) step soil profile corner (V9) step 2 glazing soil profile (pos.1.1
Riga S Riga
730 x 728 048 x 728 glazing view from inside to step :
Items needed:
Pos 1.6 (Door frame left)
Pos 1.7 (Door frame right with 8 holes)
Pos 1.1 (Soil Profile)
Soil Profile Corner (V9)
Slide pos 1.6 and pos 1.7 up to the small holes in the middle of pos 1.1(soil profile). The chamfered edge must be facing to the outside. Then attach the soil profile corner (V9) to the ends of the soil profile. to step 2:
Now you need the small side glazing.
Slide the side glazing into the door frames and soil profile.
The dimensions are listed in the diagram.
Note: After the door is mounted and aligned attach pos 1.6 and pos 1.7 with pan head screw 4,2 x 13 (S9). step 3 self-tapping screw pan head 4,2 x 3 (S9)
Note: Only attach after the door is mounted and aligned to step 3:
Now insert the cross bar (pos.
.9) onto the top of the glazing.
cross bar (pos.
.9) cross bar (pos.
.9) step 4 view from inside glazing self-tapping screw pan head 4,2 x 3 (S9) connecting plate (V5) door frame top
(pos.
.8) screw M6 x 6 (S5) with nut M6 (S ) glazing to step 4:
Items needed:
Two Connecting Plates (V5)
Pos 1.8 (Cross Bar-door frame top)
Four Hex Screws M6 x 16 (S5)
Slide one hex screw M6 x 16 (S5) into the vertical door frames(pos1.6/1.7) and two in the crossbar(pos 1.8)
Attach the crossbar to the door frames with the connecting plate (V5).
Insert the curved glazing into the door frames and cross bar (pos 1.9)
0
Assembly procedure gable
ATTENTION!
When using a foundation frame attach it to soil profile in advance (see pages 5, 6) step 5 view from outside step 6: view from outside glazing
Edge curve connects to the soil profile corner (V9) to step 5:
The square peg in the soil profile corner (V9) is plugged into the bottom of the Edge curve (pos.1.5.4/1.5.6).
The small triangular glazing is positioned in the door frame top (pos
1.8)
The Edge curve (pos.1.5.4/1.5.6) is attached to the door frame using the connecting plate (V5), installed in step
4, and 2 self-tapping screws pan head
4,2 x 13 (S9).
All fasteners should be hand tight.
- See also step 4! to step 6:
The cross bars (pos..9) are mounted horizontally with the self-tapping pan head screw 4,8 x 45 (S3).
step 7:
The rear gable is assembled in the same way!!!
Only rear gable!
x
M6x 6 connecting plate (V 0)
4x
M6x 6 cross bar
(Pos.
.8) glazing x
M6x 6 to step 7:
Slide the upright profiles (pos 1.6/1.7) into the soil profile.
Insert the (787 x 728 mm) glazing between the upright profiles (pos 1.6/1.7)
Insert one M6 x 16 (S5) into each upright profile (pos 1.6/1.7)
Insert four M6 x 16 (S5) into the cross bar
(pos 1.8)
Insert one M6 x 16 (S5) into each cross bar (pos 1.9)
Connect the upright profiles (pos 1.6/1.7) to the cross bars (1.8/1.9) with connecting plates (V10)
Attach the edge curve left/right
(pos.1.5.4/1.5.6) to the cross bars (1.9) with the self-tapping pan head screw 4,8 x
45 (S13).
You should be careful:
T-seal (V25) is for all doors and windows (total: 5 meters /49 feet)
Attention! The T-seal (V25) is only inserted on three sides of the roof window. The top side slides into the roof beam so no seal is required.
In the door threshold, the hose section
(V14) is pressed into the soil profile.
This prevents dirt from getting into the soil profile.
Attention! In the lower door press the seal into the profile first then install the rectangular tube.
Profiles for roof windows (per roof window)
overview pos. description
4.
roof window side profi le
4.2 roof window top/bottom profil number
2
2 length in mm
54
953
Content accessories bag roof window (per roof window)
overview
* pos. description/item number number
2
V25 T-seal
V 3 corner with grub screw, internal hex and fl at point 4 item no 9999 0070
V2 allen key item no 9999 0032 item no 9999 0056
S 2/
S hexagonal screw M6 x 2 nut M6 item no 9999 0 24 item no 9999 0 28
3
V24 corner bracket/roof window item no 9999 0005
4 length in mm
64
052
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
2
Assembly roof window
corner bracket/roof window (V24)
Top window profi e (pos.4.2)
(This profile requires no T-seal)
Attach the roof window side profiles to the bottom roof window profile using the corner brackets and the metal corners with grub screws.
Insert the roof window glazing into the side/bottom profiles you have assembled.
Attach the top roof window profile, tighten all grub screws and insert T seal on the three lower sides of the roof window.
Recommendation!
It is advisable to use silicon to seal where the polycarbonate enters the frame of the roof window. This will prevent rain from dripping into the greenhouse.
See page 14 for details.
Attention: In the bottom cross profile insert two hex screws M6 x 2 (S2) for the window opener!
corner with grub screw (V 3)
Bottom window profile (pos. 4.2
automatic roof window opener
Mounting roof window wrong!!!
right
Please push the roof window from the gable end into the ridge profile and slide it into position.
Install the automatic opener mount into the crossbar.
3
Sealing the roof window area
▲ pos. 4.
Please apply silicon to the
4 plastic corner connectors before installation into the roof window profiles. ( ).
▲ pos. 4.
▲ pos. 3.2
cross-section of the seal length: 2,3 m
The seal is inserted as the sketch above.
Attention: Do not cut the seal in the corners! Important!
Please seal all connections of the roof window with silicon: Corner connector to side and bottom profile and glazing to side and bottom profiles.
→
see sketch.
▲
Here you need seal all around ( )!
▲
▲ side curve pos. 2.3
cross bar pos. 3.2
window profil pos. 4.
und 4.2
4
Automatic Window Opener
opener frame
2 pressure cylinder
3 cotter pin
4 mounting plate window profil e
5 mounting plate cross bar
3
3
4 2
5
Auto Opener Installation
1.
Check whether the greenhouse window can open and close freely and unhindered.
2.
Install the window opener with the mounting plate (4) in the center of the lower roof window profile (pos 4.2)
3.
Secure the cylinder by lining up the hole in the piston with the upper hole in the Tcoupling, then insert the cotter pin.
4.
Install the mounting plate (5) in the center of the cross bar(pos 3.2) using the middle hole in the mounting plate(5)
5.
Attach the opener frame (1) to the mounting plate (5). Open the roof window until the threads of the piston (2) engage the threads of the opener frame (1). Thread the piston (2) half way into the threads in the opener frame (1).
Adjustment:
Let the opener acclimate to the greenhouse for 3-4 hours before you make adjustments.
For earlier engagement and a larger opening, turn the cylinder clockwise.
For a delayed engagement and a smaller opening turn the cylinder counter clockwise. Make sure you don’t back it out too far.
For opening engagement advance/delay one full turn is about 1 degree Fahrenheit.
Please keep in mind that greenhouse temperatures can vary and windows can have different opening tolerances.
Winter-storage:
If the greenhouse interior does not stay above freezing we recommend you remove the cylinder from the window opener or remove the entire opener. Please store it in a dry frost-free place for the winter.
Required Maintenance:
Around springtime every year, check to make sure the piston shaft and cylinder threads are greased.
Also check the piston shaft for ease of movement. A dab of marine grease on the piston shaft and the cylinder threads will be sufficient. Failure to do so could render your opener inoperable.
5
Riga Greenhouse Window Auto Opener Correct Installation
In the correct position, the opener is sitting parallel to the window, which means that it will not demand a lot of pressure from the cylinder when the opening starts. Before fitting a new cylinder to the openers, you must check that the window can open freely right from the start. If not you must change the position of the aluminum profiles.
Roof Vent Recommendation for High Wind Areas
If you get strong wind gusts, we recommend protecting your roof vents and openers with restraint cables. Roof vent restraints can be purchased from Exaco Trading (US distributor of Rigas) or can be made, they are not a standard part from the Riga manufacturer.
Two restraints are used for each window; one on each side of the window. Install each loop between two flat washers on screws inserted into the channel. Position the restraint as illustrated and adjust as needed to avoid interference from the crossbar as the window is raised and lowered.
You can make your own restraints from
1
/
16
“ stainless wire rope,stranded 7x19 for maximum flexibility.
Overall length should be about 16”. When installed near the crossbar, they will limit the window opening to less than the safe extents of the hinge and window opener, but greater than the maximum thermal extent of the opener. More important than the exact length of the restraint is a close length match for each window’s pair. If you are not equipped to swage the binding sleeves you can use wire rope clamps.
Profiles for divided revolving door - bottom -
overview pos. description
5.3.
door profile botto
5.6 door profile lef
5.7 door profile righ
5.9 door profile to
5.8 square tube with hole for sash lock with hinge hole with transverse hole with transverse hole number length in mm
700
692
692
700
740
Content accessories bag divided revolving door - bottom -
overview
* pos. description
V5 metal hinge, black item no 9999 0358 number
2
V28 sash lock item no 9999 0023
V29 QR-stopper 30 x 30 x ,5-2 item no 9999 0099
V25 T-seal item no 9999 0032
S 8 self-tapping screw countersunk head 4,8 x 25 item no 9999 0 63
S 7 self-tapping screw countersunk head 4,2 x 45 item no 9999 0 60
S 9 self-tapping screw countersunk head 3,5 x 22 item no 9999 0 52
S6 pan head screw 3,5 x 38
(square tube) item no 9999 0 38
V32 glazing block 30 x 0 x 4
V30/
V3 corner bracket door profil left - item no 9999 0009 right - item no 9999 00
4
2
2
2
4
2
2
2
8 length in mm
7 0
744
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
6
Assembly - divided revolving door - bottom -
view from outside
Lay the profiles out like the diagram below (possibly on cardboard or something similar).
corner bracket door profil
(V30/V3 )
First: Insert T seal in
Door profile top (pos
5.8)
Second : Attach square tube to door profile to (pos 5.8) with pan head screw
3,5 x 38 (S6).
QR-stopper
(V29) square tube (pos. 5.8) door profile top (pos. 5.9
sash lock (V28) with self-tapping screw countersunk head 3,5 x 22
(S 9) scews.
glazing block (V32) self-tapping screw countersunk head 4,2 x 45 (S 7) door profile bottom (pos. 5.3.1
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
7
Profiles for divided revolving door - top -
overview pos. description
5.
door profile lef
5.2 door profile righ
5.3 door profile to
5.4.
cross bar with hinge hole with hole for lockable door handle number/length in mm
Riga S Riga
08
08
264
264
700
700
700
700
Content accessories bag - divided revolving door - top
overview
* pos. description
V52 door handle, lockable outside - item no 9999 0035 inside - item no 9999 0244
S 7 self-tapping screw countersunk head 4,2 x 45 item no 9999 0 60
V32 glazing block 30 x 0 x 4 number/length in mm
Riga S Riga
6 6
2
2
7 0
2
2
2
2
2
7 0
2
295
2
V25 T-seal item no 9999 0032
V5 metal hinge, black item no 9999 0358
S 8 self-tapping screw countersunk head 4,8 x 25 item no 9999 0 63
V28 sash lock, small item no 9999 0023
S 9 self-tapping screw countersunk head 3,5 x 22 item no 9999 0 52
V33 door locking device item no 9999 0230
3 item no 9999 0 89
V30/
V3 corner bracket door profil left - item no 9999 0009 right - item no 9999 00
8
2
2
8
2
2
* Note: The seal is bundled in one strand or all doors and windows, please cut accordingly.
8
1.
2.
Assembly - divided revolving door - top -
view from outside
Place the profiles on the ground or a flat surface like the diagram below (possibly on cardboard or something similar).
corner bracket door profil
(V30/V3 ) door profile top (pos. 5.3
3.
4.
Fix glazing block in place with silicon self-tapping screw countersunk head 4,2 x 45 (S 7) cross bar (pos.5.4.
) sash lock (V28) with self-tapping screw countersunk head 3,5 x 22
(S 9) screws
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
9
Profiles for rear window
overview pos. description number/length in mm
Riga S Riga
5.
.2 door profile left with hole for sash lock
08 264
5.2 door profile right with hinge hole
08 264
5.3.
door profile top
700 700
5.4.2 door pro fi le bottom with hole for window opener
700 700
Content accessories bag - rear window -
overview
* pos. description
S 7 self-tapping screw countersunk head 4,2 x 45 item no 9999 0 60
V32 glazing block 30 x 0 x 4 number/length in mm
Riga S Riga
6 6
V25 T-seal
2
2
7 0
2
2
2
2
2
7 0
2
295
2 item no 9999 0032
V5 metal hinge, black item no 9999 0358
S 8 self-tapping screw countersunk head 4,8 x 25 item no 9999 0 63
V28 sash lock, small item no 9999 0023
S 9 self-tapping screw countersunk head 3,5 x 22 item no 9999 0 52
V85 opener for rear window item no 9999 0303
V 45 corner
(fixation of window item no 9999 04 6
S9 self-tapping screw pan head 4,2 x 3 item no 9999 0 44
V30/
V3
S 2/
S corner bracket door profil hexagonal screw M6 x with nut M6
2 left - item no 9999 0009 right - item no 9999 00 item no 9999 0 24
item no 9999 0 28
2
2
2
4
0
2
2
2
4
0
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
20
Assembly - rear window -
view from outside door profile top (pos. 5.3.1
sash lock, small (V28) with self-tapping screw countersunk 3,5 x 22
(S 9) screws self-tapping screw countersunk head
4,2 x 45 (S 7) glazing block with silicone fix in positio cross bar
(pos. 5.4.2) opener for rear window
The required mounting bracket is placed on the preinserted M6 x 6 (S5) bolts and screwed with nuts M6 (S).
opener with self-tapping screw pan head 4,2 x 3
(S9) screw
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
2 hex screw M6 x 2
(S 2) hex screw M6 x 6
(S5)
Installation of Door Catch
Door Catch Placement Riga Model IIs, IIIs, IVs
Edge Curve
Handle with Screw Cap
3.5 x 13mm Screw
Door Catch Placement Riga Model III, IV, V
Crossbar
Crossbar
Handle without
Screw Cap
3.5 x 13mm Screw
2
2
Assembly procedure - eaves -
ATTENTION! When using a foundation frame attach it to the soil profile before these steps (see pages 5, 6) step 8 to step 8:
Note: If you have purchased a foundation frame attach it to the soil profiles before you attempt this step.
First attach the soil profiles(pos 2.1) to the end gables with the preinstalled corner connectors(V9).
Next screw the corner bracket (V12) to the gable end soil profile and the side soil profile. This will secure the gable end to the side wall.
corner bracket (V 2) screwed with self-tapping screw pan head
4,2 x 3 (S9).
step 9 ridge profile (pos. 3.3) at the gable and end plate (V ) screw with self-tapping screw pan head 4,2 x 3 (S9) soil profile (pos. 2.1) slide to corner bracket step 0
Support end or hold it up ridge profil (pos. 3.3
insert the side glazing and slide into the edge curve to step 9:
Some assistance will be needed for the following steps.
We recommend you have someone stand on a ladder and hold one end of the ridge profile while you proceed with the rest of the assembly. You could also construct a support to hold it in place.
Slide the unsupported end of the ridge profile into the grooves/slots in the top of the gable end. The top portion of the ridge profile should be flush with the outside of the gable end. Now attach the end plate(V11) with pan head screws 4.2 x 13 (S9) to step 0:
Insert the glazing in the ridge beam and the soil profile. Then slide it into the Edge
Curve.
Tip:
Peel back the protective film on the glazing only around the edges. This will prevent the panels from getting scratched.
It is also a good idea to attach a stabilization angle (pos 3.4) to each of the side curves as you go along. This will help hold everything together.
2 3
Assembly procedure - eaves -
ATTENTION!
When using a foundation frame assemble in advance on this soil profile (see pag s 5,
6) step to step : shown enlarged side curve (pos. 2.3)
Tip:
A light grease on the plastic sliders may help movement.
First place a side curve up against the edge curve installed on the gable end. You want to match curvature of the edge curve with the side curve. This will ensure that the side curve is installed in the correct direction.
Slide the side curve (pos 2.3) into the ridge profile and into the soil profile. Work it down until it is flush with the glazing then work the glazing into it.
If necessary you can use a rubber mallet on the side curve to move it down. Be careful not to damage the aluminum.
step 2 to step 2:
Continue inserting the side glazing and side curves.
step 3
The connecting plate (V4) is attached from the inside with screw hex M6 x 16 and nut M6. This secures the window crossbar to the greenhouse.
to step 3:
Insert the remaining glazing panels and side curves.
2 4
Assembly procedure -eaves-
ATTENTION!
When using a foundation frame attach it to soil profile in advance (see page s 5, 6) step 4 to step 4:
Attach the preassembled door gable.
Refer to steps 8-9 for attachment procedures.
step 5
For added stability install the inside corner (V). Use the self-tapping screw pan head 4,2 x 3 (S9).
to step 5:
Install the door and windows.
Instructions, see page 2-2.
step 6
Glazing cut away in image to show installation.
Mounting roof window wrong!!!
right to step 6:
The stabilization angle (pos 3.4) is installed on both sides from inside. It is attached to the side curve with screw M6 x 16, nut M6 and washer A6,
4 screwed.
The stabilization angles (pos 3.4) are also the rear supports for the top and bottom shelf (see separate instructions).
2 5
b below roof window b gable above type of house rear gable below door/ window gable triangular b b b b b b b
2 6
Public link updated
The public link to your chat has been updated.
Advertisement
