Lumina Strip

USER MANUAL

Version 1.2 24-004-3557-00

90040-3402

Lumina Strip

GENERAL INSTRUCTIONS

Thanks for your purchasing Lumina Strip lighting equipment, which is available in Warm White (WW) version.

The Lumina Strip is compatible of both DMX & RDM and with 10 channel LED intensity adjustable. Programs

can be updated via RDM interface. It is available in master and slave control connection.

It is easy for users to

install and operate.

For the optimum operation and best performance, please read the instruction in this manual carefully and thoroughly.

WARNINGS

To protect against high electric shock and injury to person, DO NOT open or dismantle the unit.

After use, the front panel is extreme hot. Please wait at least 15 min. for absolute cool before touching it.

Otherwise, it causes the result of burning.

NEVER try to repair the unit yourself. Repair by unqualified people could cause damage or mis-operation.

This device is not suitable for direct mounting on normally flammable surfaces. To keep a minimum 0.2m safety distance to any flammable materials.

DO NOT make any inflammable liquids, water or metal objects enter the unit.

This unit contains no user serviceable parts inside. This unit contains dangerous voltages, always remove the power plug from the wall socket before any service operation and when not in use for a long time.

Earth connection is so essential.

Stop using the unit immediately in the event of serious operation problems and either contact your local dealer for a check or contact us directly.

PHYSICAL DIMENSIONS

1

Lumina Strip

Accessories(Included):

1. The unit power cable (1pcs)

2. Wing screw(2pcs) + Grommet(2pcs) + Washer(2pcs)

3. Mounting Assemble(2pcs)

MAIN FEATURES

07, 08, 10,11, 16 DMX Channels selection

Standard DMX 5-pin In/Out

16 built-in programs except for Auto & Full subject to Speed and Dimmer

0-100% dimming level

Standard DMX-512 protocol

01 Thru 100 Chase Speed adjustment

Power failure memory

LED display window-shows current activity and function state

On/Off switch

Fuse protection

INSTALLATION

Before use, make sure whether four screws are secured firmly, if not, please secure them with the screwdriver, loose 4 screws for lamp replacement.

The unit has also been designed to hold up as user's desire. So you can fix the unit on the holder by the wing screw. They are placed in the accessory bag, included.

The following installation diagrams are for user reference.

Method 1 Method 2

2

Note :

Once this unit is for hanging application, it is required to use a safety rope (sold separately, which can hold at least 10 times the weight of the fixture ) to ensure the mounting safety of the fixture by attached through the holder.

Lumina Strip

Power:

Before plugging your unit in, be sure the resource voltage in your area matches the unit required voltage.

The unit is available in a 230V version only. Because the line voltage may vary from venue to venue, you should be sure to plug the socket into a matching wall outlet before attempting to operate your unit.

Fuses:

The Lumina Strip electric system is protected by T3.15A 250V 5*20mm. Please see the printing on the case

and these fuses prevent you from overloading damaging your unit. To replace the protective fuse, use a flat

head screwdriver to unscrew the fuse holder. Pull out the old fuse and replace it with a new one. Insert the

fuse back into the slot and tighten. Always replace with exact same type fuse removed unless otherwise specified by an authorized service technician,

SYSTEM CONNECTION

Maximum amount of this units that may be connected is 16pcs(AC100-120V) or 32pcs(220-240V).

One universe DMX can drive up to 32 pcs of Lumina Strip, please add DMX booster if Lumina Strip are

connected together in line over 32 pcs or data cable over 100M. The connections may be illuminated

as following.

DMX IN

POWER IN

AC100-240V 15A MAX

Lumina Strip

1

3pin Power Cable

5pin DMX Cable

2

DMX IN

POWER IN

AC100-240V 15A MAX

Lumina Strip

1

3pin Power Cable

5pin DMX Cable

2

DMX IN

POWER IN

AC100-240V 15A MAX

Lumina Strip

1

3pin Power Cable

5pin DMX Cable

2

DMX IN

POWER IN

AC100-240V 15A MAX

Lumina Strip

1

3pin Power Cable

5pin DMX Cable

2

DMX IN

POWER IN

AC100-240V 15A MAX

Lumina Strip

1

3pin Power Cable

5pin DMX Cable

2

POWER OUT POWER IN

DMX OUT DMX IN

POWER OUT POWER IN

DMX OUT DMX IN

POWER OUT

DMX OUT

POWER IN

DMX IN

POWER OUT

DMX OUT

POWER IN

DMX IN

POWER OUT POWER IN

DMX OUT DMX IN

3

3

3

3

3

32

32

32

32

32

3

4

Lumina Strip

Layout Overview

Front Panel Overview

1

1. Lamp: Totally 10 LEDs* Warm White, 7W

Rear Panel Overview

6 1

RDM/DMX OUT

1=Ground

2=Data-

3=Data+

4,5=NC

Neutral

Earth

Live

POWER THRU(15A Max.)

0.2m

Made in China

MODE

DMX

Program

MENU

Address

Channel

No DMX

Glide

Program

Speed

Master

Lamp Mode

Fade Time

DISPLAY

001 -- 512

07 / 08 / 10 / 11 / 16

OFF / Hold / Program

OFF / ON

Full / 01-- 16 / Auto

01 -- 100

00 -- 100

Tungsten / LED

00 -- 100

MODE MENU UP

POWER

RDM/DMX

DOWN

Lumina Strip

WARNING: / ATTENTION:

RISK OF FIRE AND ELECTRIC SHOCK

RISQUE DE CHOC ELECTRIQUE ET INCENDIE

DRY LOCATIONS

EMPLACEMENTS SECS

NOT FOR RESIDENTIAL / HOUSEHOLD USE.

PAS POUR USAGE RESIDENTIEL / MENAGE.

MINIMUM SAFE TY DISTANCE TO FLAMMABLE MATERIALS: 0.2m.

DISTANCE DE SECURITE AUX MATERIAUX COMBUSTIBLES: 0.2m.

TEMPER ATURE DE FONCTIONNEMENT

O

DE SURFACE ENCEINTE EST A 60 C

FOR SUPPLY CONNECTION S USE WITH WIR E RATED AT LEAST 60 C

POUR LES CONNEXIONS D'ALIMENTATION D E FIL D'UNE NOTATION

O

MINIMALE DE 60 C

FOR SAFETY INSTRUCTION AND MOUNTING OPTIONS REFER TO USER MANUAL

10

FUSE

POWER

POWER IN:

100-240V~, 50/60Hz

FUSE:

T3.15A 250V 5x20mm

Power Consumption:

90W max.

RDM/DMX IN

1=Ground

2=Data-

3=Data+

4,5=NC

Live

Earth

Neutral

POWER IN(15A Max.)

7

9 2 3 4 5 11

1. LCD Display

This multi-function display will detail all DMX Address, Chase , Program, Speed activity that pertains to the

current operation mode of the unit.

2. Mode button

This button will call up the unit operation mode between DMX and Chase mode.

3. Menu button

This button will active the different functions in Receive and Chase modes.

8

Note: In the Chase mode, Menu key is used to only activate Chase Dimmer, Chase Program, Chase Speed,

Fade Time and Lamp Mode. While in the " Receive " mode, only used to only select DMX Address, Channel.

4. UP button

This button will increase the displayed value in the LED display.

5. Down Key

This button will decrease the displayed value in the LED display.

6. DMX Out

This connector sends your DMX signal through to the next unit.

7. DMX In

This connector accepts your DMX input signal.

8. Power Input:

AC100-240V~50/60Hz, Max15A. The supply power is input into your unit via this connector. Be sure to

always connect to proper voltage.

9. Power Thru:

AC100-240V~50/60Hz, Max15A. This connector sends the supply power to the next unit.

10. Fuse:

F3.15A 250V 5*20mm. These fuses prevent you from overloading damaging your unit. Be sure to always

replace with the exact same type fuse.

11. Power Switch:

Turn on/off the power supply.

LCD Display / Menu System

LCD Display

Mode Key

MODE MENU UP

POWER

RDM/DMX

DOWN

Menu Key Up Key

Lumina Matrix LED Menu Tree

Power indicator

RDM/DMX indicator

Down Key

Lumina Strip

5

6

Lumina Strip

OPERATION MODES

The “Lumina Strip” has two different operation modes. It can be used as a 07, 08, 10,11, 16 channel DMX dimmer. Tap “Mode”

button to switch the operation mode between “Receive Mode” and “Chase Mode”. Please follow illustrations below to

operate the unit in your desired mode.

Mode

Parameter Parameter Value

Function

DMX

Program

Address

Channel

No DMX

Glide

Program

Speed

Master

Lamp Mode

Fade Time

001-512

07/08/10/11/16

OFF/Hold/Program

OFF/ON

Full/01--16/AUTO

01-100

00-100

Tungsten/LED

00-100

To set the initial DMX receiving address

To set the DMX Control Mode

To set the status of the fixture when DMX signal is input

To set the output of the DMX Data

To select a built-in program

To set the speed level of the built-in Program

To set the intensity

To set the mode of Lamp

To set the speed of the Fadetime

DMX Mode

Use this operation mode only when you are about to use the unit as a DMX dimmer. This function can allow you set your unit dimmer function as a 07, 08, 10,11 or 16 channel DMX dimmer and DMX address. Tap “Mode” button to switch the operation mode between “DMX” and “Program”.

SA-10 LED DMX Map

Lumina Strip

DMX Channel Details

8 Bit

7 Channel Configuration

LED 1-10

0-255

Master

Dimmer

0-255

Master Dim

Fine

16-bit

0-255

Programs

Program

Speed

0-255 0-255

(Slow

Program

Fade

0-255

(Less

Dim Mode

Standard(dr 1) 0-20

Stage (dr 2)

TV (dr 3)

21-40

41-60

61-80

(dr 4)

Theatre(dr

5)

81-100

Default to

Unit Setting

101-255

8 Channel Configuration

LED 1-5

0-255 bright

LED 6-10

0-255 bright

Master

Dimmer

Master Dim

Fine

Programs

Program

Speed

0-255 0-255 0-255 0-255 bright bright Fast

Program

Fade

0-255

More

Dim Mode

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Theatre(dr 5)

0-20

21-40

41-60

61-80

81-100

Default to

Unit Setting

101-255

10 Channel Configuration

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

7

Lumina Strip

11 Channel Configuration

0-255 0-255 0-255 0-255 0-255 0-255

Master Dim

16-bit

0-255 0-255 0-255 0-255

Dim Mode

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Theatre (dr 5)

0-20

21-40

41-60

61-80

81-100

Default to Unit

Setting

101-255

16 Channel Configuration

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

8

0-255

Master Dim

0-255 0-255 0-255 0-255

Dim Mode

Standard (dr 1)

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Theatre (dr 5)

0-20

21-40

41-60

61-80

81-100

Default to Unit

Setting

101-255

16 Bit

8 Channel Configuration

LED 1&10 LED 1&10

0-255 0-255

Master

Dim Fine

0-255

16-bit

0-255 0-255 0-255

Dim Mode

0-255

Standard (dr 1)

Stage (dr 2)

0-20

21-40

TV (dr 3)

Architectural

(dr 4)

41-60

61-80

Theatre (dr 5)

81-100

Default to Unit

Setting

101-255

Lumina Strip

10 Channel Configuration

0-255 0-255 0-255 0-255

Master

Dim Fine

16-bit

0-255 0-255 0-255 0-255

Dim Mode

0-255

Standard (dr 1)

0-20

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

Theatre (dr 5)

21-40

41-60

61-80

81-100

Default to Unit

Setting

101-255

16 Channel Configuration

0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255

Master

Dim Fine

16-bit

0-255 0-255

Dim Mode

0-255 0-255

Standard (dr 1) 0-20

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

21-40

41-60

61-80

Theatre (dr 5)

81-100

Default to Unit

Setting

101-255

26 Channel Configuration

0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255 0-255

(16bit Fine)

0-255

0-255

(16bit Fine) (16bit Fine)

Master

Dim Fine

0-255 0-255 0-255 0-255 0-255 0-255 0-255

Dim Mode

0-255

Standard (dr 1)

0-20

Stage (dr 2)

TV (dr 3)

Architectural

(dr 4)

21-40

41-60

61-80

Theatre (dr 5)

81-100

Default to Unit

Setting

101-255

9

10

DIM MODES

Lumina Strip

Lumina Strip

Program Mode:

Use the operation mode only when you are about to use your unit as a channel chaser among of the 07,

08, 10, 11,16 channel chasers. The unit has 16 built-in programs except for Auto and Full. Of course, you can select any of these programs to chase for a more dramatic lighting show, and you can also control the speed at which the set programs will be chased.

1. Setting your desired Chase Program:

Once you have activated the Chase Mode, you can tap the “MENU” button to select and activate “Chase Program” menu. The chase pattern is displayed in the LCD by "Program " followed by two digits 01~16 or only "AUTO"& "FULL" appears. You can tap “UP” and “DOWN” button to select any of them to run at a single time.

Selecting any program of Program01-16 will activate the selected program; while selecting “Auto” will automatically play the built-in 16 chase programs. When select “Full” menu, all the LEDs will keep lighting.

Program

01

MODE MENU UP DOWN

Auto

MODE MENU UP DOWN

2. Chase Speed Menu:

Press “MENU’ button to select and activate “Chase Speed” menu. In this menu, you can adjust the program chase speed.

Speed

001

MODE MENU UP DOWN

Use the "UP " and "DOWN" buttons to adjust the chase speed from 001 thru 100. A set value of 100 will give you the fastest chase speed(approx.1/10th of a second) . While a set value of

001 will give you the slowest chase speed (once every 30 second.).

3. Master (Intensity) Menu:

To adjust the output intensity, you must activate the

Chase Dimmer Menu as the previous step. Press “MENU” button and select “Chase Dimmer” menu, the LCD will display

“Dimmer” followed by three digits.

Use the "UP" and "DOWN " buttons to adjust the light output

intensity between 000 ~ 100. A set value of 000 will give you

the weakest output intensity and a set value of 100 will give

you the full intensity.

4. Lamp Mode Menu:

Press “MENU” button and select “Lamp Mode” menu, the LCD will display “LampMode Tungdten”, user can press “UP” or “DOWN” button to switch to “LampMode LED” menu.

5. Fade Time Menu:

Press “MENU” button and select “Fade Time” menu, the LCD will display “FadeTime” followed by three digits, user can press “UP” or “DOWN” button set the desired Fade time value from 000 to 100.

Speed

100

MODE MENU UP DOWN

Dimmer

001

MODE MENU UP DOWN

Dimmer

100

MODE MENU UP DOWN

LampMode

LED

MODE MENU UP DOWN

FadeTime

000

MODE MENU UP DOWN

11

12

Lumina Strip

Lumina Strip RDM Parameter IDs

The following tables outline and describe all the RDM parameters IDs associated with Lumina Strip.

Table 1: Lumina Strip RDM Parameter IDs

Lumina Strip

Elation lighting

Lumina Strip LED Light

Lumina Strip

Channel Parameter details：

Parameters

Dimmer DMX value

Functions

0---100%

equal to intensity 0

---

100%

Program

DMX 0

--

7 for local DMX Dimmer Mode

DMX 8

DMX 16

--

15 Full

--

23 Program1

DMX 24

--

31 Program2

DMX 32

--

39 Program3

…

DMX 136

--

143 Program16

DMX 144

--

255 Auto

Speed

FadeTime

LampMode

Play Mode

Master

The bigger DMX value is, the faster the Programe runs

DMX value

0

---

100% equals to FadeTime 0---100%

DMX 0

--

127 for choosing the work mode of the LED

DMX 128

--

255 for choosing Tungsten

DMX 0

--

80 to stop the Program

DMX 81

--

160 to pause the Program

DMX 161

--

255 to play the Program

DMX value 0--- 100% equals to Program intensity

0--100%

1. Selecting DMX Address

Press “MENU” button and select DMX channel address menu after having

activated the Receive Mode. The DMX Address Mode is indicated by

"Address” followed by three digits 001~ 512. You can tap the “UP” and

“DOWN” buttons to change the DMX Address Value.

Address

001

MODE MENU UP DOWN

Note: There is no DMX input in the master unit of the connection.

2. Selecting the DMX Channel

Press “MENU” button and select Channel Mode. The Channel Mode is indicated by "Channel" followed by two digits 07,08, 10, 11,16. You can tap the "UP” and "DOWN" buttons to change the setting from 07, 08, 10,11 or

16 which you wish to run.

NOTE:

Channel

01

MODE MENU UP DOWN

1. When CH:07 is displayed, overall channels will be controlled by one DMX channel.

2. When CH:08 is displayed, channel 1 and 2 will be controlled by one DMX channel, channel3 and 4 will

be controlled by one DMX channel, and so forth, channel 9 and 10 will be controlled by another .

3. When CH:10 is displayed, channel1~10 will control an individual LED fixture.

4. When CH:11 is displayed, each channel will be controlled by one DMX channel. This is the factory

default setting.

5. When CH:16 is displayed, 1-10 will control the LED, and the 11-16 will control to run a special

program.

13

14

Table 1: Lumina Strip RDM Parameter IDs

Lumina Strip

Lumina Strip

Table 2: Lumina Strip Manufacturer Status IDs

Manufacturer Defined Status IDs

Manufacturer Specific messages are in the range of 0x8000 —0xFFDF. Each Manufacturer-specific

Status ID shall have a unique meaning, which shall be consistent across all products having a given

Manufacturer ID. See Table B-2, ANSI E1.20-2010

Status Message ID

8100H

Value Data Value 1 Data Value 2

00H 00H

Status ID Description

ALL OK

Table 3: Lumina Strip Manufacturer Specific PIDs

Manufacturer Specific PIDs

Manufacturer Defind PIDs range is 0x8000-0xffdf. See Table A-3, ANSI E1.20-2010

Get

Allowed

SET

Allowed

RDM Parameter

Id’s

TYPE LENGTH UNIT PREFIX MIN MAX DEFAULT DESCRIPTION

8A08H

8A09H

8A01H

8A42H

8A0BH

U8

U8

U8

U8

U8

1

1

1

1

1

NONE NONE 0

NONE NONE

NONE NONE

1

0

NONE NONE

1

NONE NONE

0

18

100

99

1

2

1

1

1

1

0 chase program chase speed chase dimmer lamp mode fade time percent

15

16

Lumina Strip

PROGRAM UPDATE

Programs of this device can be updated via the RDM interface with proper tool named SC-NODE and RDM Program Tool. Connect the Lumina Strip to the output terminal of the SC-NODE then connect the SC-NODE to the PC, run the TCP/IP setting, see the following figures for details.

After the TCP/IP is set, run the RDM_Program_Tool.exe software, the tool will search RDM devices automatically for the first time, user may also search devices via ArtTod Control command.

When the software searched a RDM device, the RDM UID will be listed in the “RDM UID Lists”. Select the listing

RDM UID, then press “Update Selected Device” command to upload the desired updating program, press “open” command to start updating. After finishing updating, the software will start to search device once again, and showing

“update successful!”, means program updating completed.

Lumina Strip

TECHNICAL SPECIFICATIONS

Power Thru/Input AC100~240V,50/60Hz

IP Rating IP20

Power Consumption 90W

Weight 6.3Kg

Fuse T3.15A 250V 5*20mm

Dimension 1040(L)*130(W)*140(H)mm.

Please note: Specifications and improvements in the design of this product and this manual are subject to change without any prior notice.

Explanation For The Label

RDM/DMX OUT

1=Ground

2=Data-

3=Data+

4,5=NC

Neutral

Earth

Live

POWER THRU(15A Max.)

0.2m

Made in China

MODE

DMX

Program

MENU

Address

Channel

No DMX

Glide

Program

Speed

Master

Lamp Mode

Fade Time

DISPLAY

001 -- 512

07 / 08 / 10 / 11 / 16

OFF / Hold / Program

OFF / ON

Full / 01-- 16 / Auto

01 -- 100

00 -- 100

Tungsten / LED

00 -- 100

MODE MENU UP

POWER

RDM/DMX

DOWN

Lumina Strip

WARNING: / ATTENTION:

RISK OF FIRE AND ELECTRIC SHOCK

RISQUE DE CHOC ELECTRIQUE ET INCENDIE

DRY LOCATIONS

EMPLACEMENTS SECS

NOT FOR RESIDENTIAL / HOUSEHOLD USE.

PAS POUR USAGE RESIDENTIEL / MENAGE.

MINIMUM SAFETY DIST ANCE TO FLAMMABLE MA TERIALS: 0.2m.

DISTANCE DE SECURITE AUX MATERIAUX COMBUSTIBLES: 0.2m.

O

MAXIMUM OPERA TING TEMPERA TURE OF ENCLOSURE SURFACE IS 60 C

TEMPERA TURE DE FONCTIONNEMENT

POUR LES CONNEXIONS D'ALIMENT ATION DE FIL D'UNE NOT ATION

FOR SAFETY INSTRUCTION AND MOUNTING OPTIONS REFER TO USER MANUAL

FUSE

POWER

POWER IN:

100-240V~, 50/60Hz

FUSE:

T3.15A 250V 5x20mm

Power Consumption:

90W max.

RDM/DMX IN

1=Ground

2=Data-

3=Data+

4,5=NC

Live

Earth

Neutral

POWER IN(15A Max.)

Indicating that the ambient temperature should not be above 40 degrees.

Minimum safety distance to lighted object: 0.2m.

SPECIAL NOTE

This fixture can be easily mounted with the provided mount assemble, meanwhile a safety rope(sold separately) is always required to ensure the mounting safety of the fixture by attached and fastened through safety chain

/cord attachment point. This safety rope can hold at least 10 times the weight of the fixture and with a screw on it.

Mount Assemble

Safety Rope

Mount Assemble

17