PreDCR Building Proposal Approval User Guide
Publicité
Publicité
PreDCR User Guide
An Automatic solution for Approval of Building Proposal and Work Flow
Management
Prepared By
SoftTech Engineers .Pvt. Ltd.
Pune.
Document outline 2
Contents:
BOUT THE DRAWING PROTOCOL DOCUMENT
OW TO READ THIS DRAWING PROTOCOL DOCUMENT
2
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 3
3
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 4
4
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 5
5
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 6
6
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 7
7
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 8
8
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 9
9
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 10
)..................................................................................... 119
10
PreDCR User Guide : Municipal Corporation Greater Mumbai
Document outline 11
Document outline
About the drawing protocol document
Mumbai Municipal Corporation has planned to automate the building plan approval process by introducing AutoDCR system. AutoDCR software reads the CAD drawings submitted by architects and automatically produce the deviation report based on the control regulations prescribed by
MCGM .
The purpose of this document is to establish a set of guidelines to Architects for preparation of drawings to be submitted for taking Building Permission from MCGM, Uniformity in the process of drafting of the drawings to be submitted for approval is required for automation of building approval system by introducing AutoDCR system.
The consultants/Architects should prepare the drawings keeping specific objects in specific layers with specific colors and text. The layers required to be generated with explanation of what is required to be drawn on which layer is described in this document. This document serves as a source of information on obtaining level of consistency in drafting and approval process focuses on both the theoretical and practical description of process flow and protocol to be used while preparing drawings for submission at MCGM for Building Permission. The document explains use of PreDCR utility.
How to read this drawing protocol document?
This document should be read in conjunction with the building bye-laws which will be applicable for approval of a proposal. The reader of this document should have understood the applicable bye laws for scrutiny of a proposal. The reader should also be familiar with AutoCAD terminology and environment for better understanding of the system. It is more exploratory in nature than the specifications and contains sections to explain particular aspect of planning and designing.
11
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 12
Drawing pre-formatting utility (PreDCR)
Overview
AutoDCR is a unique and innovative approach to automate scrutiny of building proposals by reading CAD drawings. AutoDCR software needs preformatted drawings with some specifications.
PreDCR is a software application used to create the architectural plan as per AutoDCR software requirements. It helps in standardization of drawings and helps in reducing time required for preparing submission drawings. It works under AutoCAD environment with additional menu & toolbar.
Using PreDCR commands user can create all the required layers in one click. Once all the layers are created in the drawing user can use AutoCAD commands to draw entities on the corresponding layers with the help of PreDCR software. Short commands are provided to activate any layer in PreDCR. PreDCR also helps in correcting drafting errors in the drawing. At any time user can verify if the drawn entities are properly closed or not, if proper name text has been written inside all closed poly or not etc. PreDCR will highlight all the failed entities if any.
12
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 13
Aims & objectives
To bring uniformity and standardization in submission drawing format.
To create error free drawing by auto-correction of drafting errors.
To Increase drafting speed and efficiency
To reduce drawing data redundancy.
To remove dimensioning and area calculation requirements from submission drawing format and auto-calculating areas in AutoDCR automatically.
Salient features
Automatically creating required layers in the drawing
13
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 14
Automatically creating and inserting entites of required size in the drawing: User can define size of entity and insertion point in the the drawing.PreDCR will create and insert entity in the drawing at specified location.
Automatic insertion of required text in the drawing.
Drawing cleaning, refinements of poly lines, text and closed entity verification will be done by
PreDCR to eliminate drafting errors.
14
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 15
PreDCR verify and will highlight failed entities in verifications with detailed explanation and Auto-
Zooming.
15
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 16
Benefits of PreDCR
1) Standardization of submission drawings-Brings uniformity & standardization in submission drawing format. This software will correct some minor drafting errors and also provide list of failed entities with Auto-zooming facility so that user can easily locate the failed entities in the drawing.
2) Operational ease and convenience-Data redundancy is eliminated from the drawing. Only minimum required entities are to be drawn in the drawing as most of the data will be auto detected by the system from existing available data.
3) Increased speed and efficiency-PreDCR facilitates Auto insertion of many drawing entities like parking, door windows etc of required size and number. Test auto-insertion facility saves text typing efforts. Auto-dimensioning and auto-calculation facility saves calculation efforts. Using this software user can create all the required layers at one click.
4) Accuracy - Accuracy in area calculations is achieved. Preparing Calculation tables, showing dimensions in the drawing is not required.
Drawing formats
1) Conventional submission drawing format
Conventional drawing submission format
16
PreDCR User Guide : Municipal Corporation Greater Mumbai
2) As per PreDCR format specified by PreDCR
Drawing pre-formatting utility (PreDCR) 17
3) After scrutiny of drawing using AutoDCR-
17
PreDCR User Guide : Municipal Corporation Greater Mumbai
Drawing pre-formatting utility (PreDCR) 18
Protocol details
PreDCR
is a
software
application used to create the architectural plan as per
AutoDCR
software requirements. It works under AutoCAD environment with additional menu & toolbar.
Using PreDCR commands user can create all the required layers in one click. Once all the layers are created in the drawing user can use AutoCAD commands to draw layout plan.
As per AutoDCR requirement
all building items like proposed plot, proposed work should be drawn on the corresponding layers. Short
commands are provided to activate any layer in PreDCR
At any time user can verify if the drawn entities are properly closed or not, if proper name text has been written inside all closed poly or not etc. PreDCR will highlight all the failed entities if any.
PreDCR can be used to modify/make and verify the existing or new architectural plan as per
AutoDCR
software
requirements. Users are free to use AutoCAD commands and or PreDCR commands to achieve
the main purpose which is
:
Drawing the architectural plan in DWG format as per AutoDCR software requirements.
For
Automating
the process of Development Control Regulations user/draughtsman/architect have to follow some specifications. The following are the list of specifications that the user should follow.
Plot layout, detailed floor plan and building section for all the floors should be there in one AutoCAD drawing file.
All building items like proposed plot, proposed work, proposed parking etc
must
be drawn using closed polyline
.
( i.e
. Every entity must be closed LWPOLYLINE except Railway Line , Drain line, Water Line, Electric
Line, Dead Wall and Ground level.).
Building Sub-Items must be exactly inside of outer closed polygon as per their place
in architectural plan.
This means none of the edge or vertex of inside entity should be drawn
outside its container entity.
For example Parking or Open Space poly must be exactly inside the main plot poly.
Tools are provided in
PreDCR
to verify this check.
Every Building Sub-Items should be given a specific/unique name (Text or MText entity) on the same layer & inside the entity poly.
If name not found then AutoDCR will generate the name
18
PreDCR User Guide : Municipal Corporation Greater Mumbai
automatically. Naming Conventions should be followed properly. e.g. Each Room should be given the concerned name Using <Assign Name> function of preDCR
Living, Kitchen, Bedroom...Etc.
Floor Name: GROUND FLOOR; TYPICAL FLOOR 1
, 2
& 5-8; TERRACE FLOOR
Floor Items: Room Names should be given properly without using abbreviations so the software can identify perfect entity. This can be done by Assign name facility provided by the software.
User shall use only following kind of entities for Building Items: -
LWPOLYLINE / TEXT / MTEXT
If in a plan two proposed work are mirrored in that case user should provide two separate building plans for each proposed work.
19
Installation and Registration
System Requirements
Pentium IV or better (or compatible processor)
1 GB RAM (minimum)
Windows 98/2000/XP/7/8 {32 bit & 64 bit}
CD-ROM drive
AutoCAD 2000 and onwards
Installation
To install PreDCR software on your computer please follows the given steps.
Step 1: Insert the supplied PreDCR CD in CD drive of the computer.
Step 2: Run the PreDCR installer by double clicking on file "PreDCR_Installer.exe" in the PreDCR CD.
Step 3: Follow the next steps in installer wizard to complete installation.
19
PreDCR User Guide : Municipal Corporation Greater Mumbai
Methodology
After successful installation, a PreDCR shortcut will be placed on your computer desktop as shown below.
20
Figure 1: PreDCR shortcut on desktop
Methodology
1) Open the PreDCR software for clicking on PreDCR menu on your desktop & select the AutoCAD version & then click on "OK" button.
20
PreDCR User Guide : Municipal Corporation Greater Mumbai
Methodology
2) First open submission drawing which is now converting in PreDCR format.
3) Save as your drawing with give some name.
4) Check the scale by using Scale command. If drawing is not in 1: 100 scale then covert into the 1:100
21 scale. & then make that drawing in metric scale if it is in other than meter.
5) Also make the site plan in 1:100 scales.
Click on PreDCR first tab to select the Type of Project that is " Proposed Development“ , “Land
Division” or “Plotting Layout”, etc. a) If Plot is Already sanctioned & user have to take permission for the buildings only then select
“Proposed Development.” b) If User having Proposal is Amalgamation or Subdivision then select “Land Division” option from the list. c) If Proposal having a Plotting Layout then select that “Plotting Layout” option from the list. d) If Proposal having compound wall or substructure permission then “Compound Wall/Substructure” option.
Once you clicked on ok button software will show you following dialog.
21
PreDCR User Guide : Municipal Corporation Greater Mumbai
Methodology 22
8) Then u will get the list of PreDCR toolbar, then just click on "OK" button. Now all the Layers u will get in Layer Properties managers.
9) User need to draw particular layer wise poly line and need to marked it accordingly. (Layer information is provided below)
10) Once drawing is complete to draw then need to following process to verify currant drawing.
11) Mark the margins by using Mark margin tab from from PreDCR tool bar.
Front margin is automatically marked by system according to main access road. User need to mark side and rear margin only.
12) When Mark margin is done, Click on "Verify Closed poly" option from Predcr tool.
22
PreDCR User Guide : Municipal Corporation Greater Mumbai
Select all layers to verify it in proper format.
Methodology 23
13) When u will get these message "Entities on Predcr Layers are verified and found o.k." then only u can submit a softcopy of your drawing to the Corporation.
23
PreDCR User Guide : Municipal Corporation Greater Mumbai
Methodology 24
If all drawing is ok acceding to PreDCR then you will get following massage else will appear failed list.
14) If any failed entities are present, you see report by using "Failed list” tab.
14) You can check minimum entities are present on not in drawing according to selected type of project by using “Objection list” tab.
24
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 25
PreDCR Layer Information
Layer: _Amalgamation
Description :
Draw a continuous poly around the plots you want to amalgamate.
Amalgamation contains more than one plot amalgamated together.
All entities having amalgamation as their container entity should be uniquely present in each amalgamation.
I.e. suppose there is a road widening in the Plot then the poly of road widening should be different for each amalgamation. (For amalgamation, draw plot 1, plot 2, plot 3 on plot layer and amalgamated plot Amal Plot 1, on amalgamation layer overlapping plot
Shortcut Command:
AML
How to draw :
Amalgamation:
Following rules will be applied to Amalgamation layer
Name
Recreation ground
Amenity
Road Widening
Pathway
Internal road
Main road
Reserve area
NotInPossession
IntDPRoad
BLDGBLOCK(in layout)
ExStructure
Right-of-way
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
25
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 26
Layer: _Amenity
Description :
Draw Amenity space as a closed polyline which is reserve for utilities, services and conveniences.
Shortcut Command :
AMN
How to draw :
Amenity
Following rules will be applied on the objects of Amenity layer
Deduction
Addition
Precautions to be taken –
Draw polyline correctly and give text on same layer.
If this polyline has not been drawn and texted correctly then rules will not get checked properly.
26
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 27
0
Layer: _ArchProj
Description :
This layer is used to represent various Architectural Projections in your Plan. Draw a closed
Polyline for Architectural Projections. And mark it using Mark->Projection from PreDCR menu, according to requirements.
Shortcut Command:
AP
How to draw :
Architectural Projections:
Following rules will be applied to of ArchProj layer
Width
Length
Depth
Area
Height
Following entities should be drawn on same layer.
Chajja
Cornice
Whether Shade
Flower bad
Loft
Canopy
Porch
Rewas projection
27
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 28
Steps
Otto
Garbage shaft
Refuge chute
Ornament projection
Ornamental Glazing
Precautions to be taken –
Draw polyline correctly.
Provide Marking to each poly by using “Mark → Projection” from PreDCR Menu.
If this object has not been marked properly then it won't be checked.
Layer: _ArtiVentiShaft
Description :
Draw Ventilation shaft/duct area as a closed Polyline with Text inside Outer Wall layer (BUA) on
_ArtiVentiShaft Layer. Only those shafts to be drawn on same layer where ventilation taken for
Non- habitable room.
Shortcut Command:
AVD
How to draw :
ArtiVentiShaft:
Following rules will be applied to ArtiVentiShaft layer
Area
Width
Deduction from BUA.
Precautions to be taken –
Draw polyline correctly and give text on same layer.
28
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 29
Layer: _Balcony
Description :
Draw Open/ Dry, Fire balconies as a closed polyline which is a horizontal projected to building line including parapet to serve as a sitting out place. Text of balcony must be inside and on
_Balcony layer.
Balcony must overlap with Outer Wall.
Shortcut Command :
BL
How to draw :
Balcony:
Following rules will be applied for Balcony
Balcony width
Balcony to plot boundary distance.
Precautions to be taken -
Draw a closed poly line and Mark it by using Balcony option from PreDCR Menu.
You can mark open / dry or fire balconies.
29
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 30
Layer: _Building
Description :
Building is used to group all floor plans of the same building. Draw a closed poly enclosing all the floor plans and section of the same building on _Building layer. Note: As written above, dimension or area of this building poly has no meaning in AutoDCR. This is just a logical group of all floors of the same building. If the building plan of multiple PWorks or wings is same then building name shall be as given in table below.
Building names can be.
1 "A(Monarch)" PWork "A" has building plan "Monarch".
2 "A,B(Monarch)" or "A&B(Monarch)" Wings A, B have same building plan
"Monarch".
3 "A-C(Monarch)"
4 "A1-A3(Monarch)"
Wings A, B, C have same building plan
"Monarch".
Wings A1, A2, A3 have same building plan
"Monarch".
Shortcut Command :
BLD
How to draw :
Building:
30
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 31
Following rules will be applied on the objects of Building layer
Linking of each building with its proposed work which is available in plot boundary.
Precautions to be taken –
Draw a closed poly line with peripheral of all entities of building including Floor plans, Section,
Elevation, etc. properly and give text by using PreDCR Menu Assign Name → Building &
Proposed Work.
If this polyline has not been draw and marking correctly then all above rules will not get checked
Building poly area shall not be calculated for any area calculation. It is a reference to identify building details only.
Layer: _BuildingLine
Description :
Draw a “_BuildingLine” as a closed poly line which area to be calculated for consumption of actual building line of that floor excluding cantilever projections.
Shortcut Command :
BDL
How to draw :
Building Line:
Following rules will be applied for Building Line
Coverage calculation
Margin calculation
31
PreDCR User Guide : Municipal Corporation Greater Mumbai
Precautions to be taken -
Draw a closed poly excluding cantilever projection of the floor.
Draw column overlapping with it
PreDCR Layer Information 32
Layer: _BldgBlock (in layout)
Description :
If you are getting permission for sub-division or amalgamation layout and containing building in it, then you need draw building periphery of that building on “_BLDGBLOCK” layer. In this case, tentative block of building will refer just the presence of building in sub-divided or amalgamated
Plot.
Shortcut command :
BLDBLK
How to draw :
32
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 33
Layer: _Carpet area
Description :
Draw carpet area as a closed poly line which is a net usable floor area within a building excluding that covered by the walls or any other areas specifically exempted from floor space index computation in this regulation.
Shortcut command:
CPT
How to draw :
Carpet Area:
Following rules will be applied to carpet area layer
Per Carpet Tenement number check required
Parking car, scooter, cycle
Tenement density
Water tank calculation
Sanitation
Precautions to be taken –
Draw poly line correctly Give text to this object in same layer.
If this poly line has not been drawn and named correctly then all above rules will not get
checked.
If more than one carpet area poly line containing in single tenement then need to mark it as split by using PreDCR Mark menu.
If slum development project then need to marked it as slam rehab, sale from menu.
33
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 34
Projection affected portion (PAP) also can be marked from menu
Layer: _Chowk
Description :
Draw a chowk as a closed poly line which is an enclosed space permanently open to the sky within a building at any level. From chowk we take ventilation for habitual rooms.
Shortcut Command :
CWK
How to draw :
Chowk :
Following rules will be applied on the objects of Chowk layer
Area
Width
Deductions from BUA
Precautions to be taken –
Draw polyline correctly Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked.
34
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 35
Layer: _Column
Description :
Draw each column as closed poly line on “Column” layer inside parking floor as well as inside and overlapped with Building line layer in other floors.
Shortcut Command :
COL
How to draw:
35
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 36
Layer: _CommOuterWallI
Description:
Draw a “_CommOuterWall” as a closed poly line which area to be calculated for BUA consumption including cantilever projections on that floor. This poly line to be used for commercial buildings.
Shortcut Command :
CMFS
How to draw
:
CommOuterWall:
Following rules will be applied for the same.
Commercial built up area calculations
Permissible FSI commercial BUA in mixed use
Permissible architectural projection
Converge check
Use of building
Precautions to be taken –
Draw a closed poly line correctly where commercial building is proposed.
Ploy line must be inside of _Floor layer.
Layer: _Compound Wall
Description :
Draw closed poly line of compound wall to be drawn on proposed compound wall with text started with compound wall height. E.g. 1.5m. High Compound Wall
36
PreDCR User Guide : Municipal Corporation Greater Mumbai
Shortcut Command :
CW
How to draw :
Compound Wall:
Following rules will be applied to Compound Wall
Height
Precautions to be taken –
Draw a closed poly line correctly with containing text in it
Give name to this object in same layer as that of object.
PreDCR Layer Information 37
Layer: _CrzBoundary
Description:
CRZ boundary- Boundary of coastal regulatory zone shall be drawn on _CRZBoundary layer inside Plot boundary.
Shortcut Command :
CRZ
How to Draw:
37
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 38
Layer: _DeadWall
Description :
Draw open polyline overlapping with proposed work on a side from where ventilation is not taken and should be draw inside the plot
Shortcut Command :
DW
How to draw :
Dead wall:
Following rules will be applied to Dead wall layer
Margins
Precautions to be taken –
Draw an open poly line correctly overlapping with proposed work.
Give name to this object in same layer
38
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 39
Layer: _Door
Description :
Door is a closed Polyline which is drawn on “_Door” layer. Also you can insert a particular size poly for Door using Insert->Door from PreDCR menu.
Shortcut Command :
DR
How to draw :
Door:
Following rules will be applied to Door layer
Width
Depth
Height
Precautions to be taken –
Insert poly line from Insert menu correctly
Text insertion point must be inside poly line.
39
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 40
Layer: _ElecLine
Description :
Electric line will be present in the layout plan and shall pass through plot entity as a non closed poly line.
Name electric line shall start with its voltage capacity and text insertion point shall lie on its poly line.
For e.g. 33 KV High Tension Line
Shortcut Command :
L1
How to draw :
Electric line:
Following rules will be applied on the objects of electric line layer
Building distance check depend on 33kv high voltage & low voltage
Precautions to be taken –
Draw an open poly line correctly and give text on same layer.
40
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 41
Layer: _Elevation
Description : -
Elevation to be drawn in _Elevation layer only for printing purpose. No regulations will be checked by reading this layer. The drawing on this layer need not be drawn using poly lines
Shoutcut Command :
EL
How to draw :
Layer: _ExStructure
Description:
41
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 42
Draw a structure which already approved by authority on “_Exstructure” as a closed poly. And mark this as 'To be demolished' or 'to be retained’ by using Mark option from PreDCR Menu.
Shortcut Command :
EX
How to draw :
ExStructure:
Following rules will be applied on the objects of Exstructure layer
Existing coverage area
Existing built up area
Precautions to be taken –
Draw poly line properly and give a text and Mark “To be Demolished”
Mark it as “To be Retained” as “Building” Or “Structure”
Layer: _ExtToiletDuct
Discription:
Draw an Outer toilet shaft area as a closed Polyline with Text inside Outer Wall layer
(BUA) on “_ExtToiletDuct” layer.
42
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 43
Layer: _Floor
Discription:
Draw a Floor as a closed poly line to the boundary of the lower surface in a story on which one normally walk in a building and including mezzanine floor also. The floor at ground level with a direct access to a street or open space shall be called the ground floor; the floor above it shall be termed as Floor 1 with the next higher floor being termed as Floor 2 and so on upward. For giving the name of each floor use the assign named option from the PreDCR menu. Also draw each floor separately. While giving name to the typical floor then use a typical option from Assigned name -> Floor name option from PreDCR menu bar.
Shortcut Command :
FLR
Floor Name: - Floor name will be taken from text inside floor poly and on same layer.
A floor plan is automatically associated/linked by AutoDCR software with one or more floor section poly in Section plan. This is done by matching name of Floor Plan and
FloorInSection so both must be same.
Typical Floor Non-Typical
"TYPICAL" X "FLOOR PLAN"X: Floor numbers in specific format (, or & or -) e.g.:
TYPICAL 1,2 FLOOR PLAN
TYPICAL 1-4 FLOOR PLAN
TYPICAL 2&3 FLOOR PLAN
X "FLOOR PLAN"
X: Direct Floor's Name e.g.
GROUND FLOOR PLAN
FIRST FLOOR PLAN
SECOND FLOOR PLAN
How to draw :
Floor:
Following rules will be applied on the objects of Floor layer
Containing all entities of floor
Corresponding check with its section
Precautions to be taken –
Draw a closed poly line properly and give text by using Assign Name option from PreDCR
Menu.
43
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 44
Layer: _FloorInSection
Description :
Draw a FloorInSection poly line as a closed poly of section boundary which contains all floors with stair cabin, Liftwell machine room, water tanks etc. as shown in the figure.
Also write the name as "Section" in this section poly.
In this closed poly of section draw sections of all floors with stair cabin, inner Chowk,
Liftwell machine room, Ventilation shaft, water tanks etc. as shown in the figure.
Also write the name as "Section" in this section poly.
This section poly will present inside the building poly.
Shortcut Command :
SECF
How to draw :
Floor In section:
44
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 45
Following rules will be applied on the objects of Floor In section layer
Floor height
Terrace height
Plinth height
All Corresponding check
Precautions to be taken –
Draw a closed poly line properly and give text by using Assign Name option from PreDCR
Menu.
Floor and floor in section text must be link with each other.
Layer: _Ground Level
Description :
Draw the Ground level line as open poly line in section .It is used for checking a total building height from this line.
Shortcut Command :
GL
How to draw :
Ground Level:
Following rules will be applied on the objects of Ground level layer
Total Building Height
Floor height from Ground level
Basement height from Ground level
Plinth checking
Precautions to be taken –
Draw a open poly line correctly and give text on same layer
If this poly line is not drawn and texted correctly then all above rules will vary.
45
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 46
Layer: _IndOuterWall
Description :
Draw a “_IndOuterWall” as a closed poly line which area to be calculated for BUA consumption including cantilever projections on that floor. This poly line to be used for
Industrial buildings.
Shortcut Command
: IFSI
How to draw :
Industrial Outer Wall:
Following rules will be applied
Industrial built up area calculations
Permissible FSI Industrial BUA in mixed use
Permissible architectural projection
Converge check
Use of building
Precautions to be taken –
Draw a closed poly line correctly where Industrial building is proposed.
Ploy line must be inside of _Floor layer.
46
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 47
Layer: _IntDPRoad
Description :
Draw existing or proposed D. P. (Development Plan) road or T. P. (Town Planning) Road when inside/intersected with plot. While giving name start text with road width. E.g. 15m wide D. P.
Road.
Shortcut Command :
R3
How to draw :
Internal DP Road:
Following rules will be applied
Width
Area
Margin
Deduction
Net plot area calculation
Precautions to be taken –
Draw a closed poly line correctly and give text on same layer.
Give text with start of road width.
It should be intersect with main plot.
47
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 48
Layer: _InternalRoad
Description :
Draw internal road with text specifying its width and draw a center line on same layer with its line type center.
Shortcut Command :
R2
How to draw :
Internal road:
Following rules will be applied
Width
Length
Precautions to be taken –
Draw a closed poly line correctly and give text on same layer.
Give centre line in middle of closed poly line with line type Centre.
Give text with start of its width.
48
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 49
Layer: _Liftwell
Description :
Draw a Lift well as a closed poly line which is a mechanically guided car, platform or transport for persons and materials between two or more levels in a vertical or substantially vertical direction.
If fire Lift well is provided then use the marking of “Fire Lift well" option from Mark -> Lift well ->
Fire Lift well. Fire Lift well means a special Lift well designed for the use of fire service personnel in the event of fire or other emergency.
Shortcut Command :
LFT
How to draw :
Lift Well:
Following rules will be applied on the objects of Lift well layer
Lift well area
No of proposed common Lift
width
Capacity
Free from BUA
Taken in BUA
Hydraulic Lift
Car Lift
Fire Lift
Precautions to be taken –
Draw poly line properly and give text to using mark option from PreDCR menu.
Mark it as Free from BUA if it is to be deducted, else will add in BUA.
49
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 50
Layer: _Location Plan
Description :
Locations plan if any to be drawn on this layer. This is only for reference. No verifications to be done by AutoDCR for this layer, it is required for printing purpose only.
Shortcut Command :
LCP
How to draw :
50
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 51
Layer: _Main Plot
Description:
Draw a Plot poly as a closed polyline which is a parcel or piece of land enclosed by definite boundaries. A Plot will contain all Proposed Works (buildings, wings), open space, Internal Roads,
Parking etc. The overall Plot Entity represent a Plan, AutoDCR refers it as 'Layout Plan'. The overall Plot Entity represent a Plan, AutoDCR refer it as "Layout Plan".
Shortcut Command:
PLT
How to draw :
Main plot:
Following rules will be applied to main plot layer
Size plot area
Permissible FSI
Requirement of Amenity
Requirement of Recreational ground
Requirement of Internal road, etc.
Precautions to be taken –
Draw a closed poly line correctly with text on same layer.
Provide Main access road overlapping with main plot.
Provide R.G, Amenity, reserve area, Road Widening, etc. inside Plot boundary
Layer: _Main Road
Description:
Draw a Main Road as a closed poly line which is abutting the plot. On the site that road is any type of road. Such as any highway, street, lane, etc. over which the public have a rite of passage
51
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 52 or access or have passed and had access uninterruptedly for a specified period, whether existing or proposed in any scheme. Road name start with its width only.
Shortcut Command :
R1
How to draw :
Main Road:
Following rules will be applied to main road layer
Main road Width
Front Margin
Building height
Access to plot
Precautions to be taken –
Draw a closed poly line correctly with mentioning its width.
Draw it overlapping with main plot
Layer: _Margin Line
Description :
No need to draw Margin Line, Just use Mark Margin tool for it. This layer is not provided for users. AutoDCR uses '_MarginLine' layer for its own internal use.
Layer: _Nala-WaterCourse
52
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 53
Description :
Draw Nala-WaterCourse polygon on this layer and give Proposer text inside it.
Shortcut Command :
R4
How to draw :
Nala-WaterCourse:
Following rules will be applied to Nala.
Deduction from Plot
Nala to building Distance check
Precautions to be taken –
Draw a closed polyline correctly and provide text inside it.
Layer: _NETPLOT
Description :
No need to draw NETPLOT. This layer is not provided for users. AutoDCR uses '_NETPLOT ' layer for its own internal use.
Layer: _NDZ
Description :
No Development zone area if any inside plot to be drawn on this layer. And it should be drawn inside the plot with text on _NDZ layer.
53
PreDCR User Guide : Municipal Corporation Greater Mumbai
Shortcut Command :
NDZ
How to draw : -
NDZ:
Following rules will be applied on the objects of NDZ layer
Reserve area
Deduction and additional in net plot area
Precautions to be taken –
Draw a closed polyline correctly and provide text inside it.
PreDCR Layer Information 54
Layer: _NotInPossission
Description :
Plot area which is not in possession or which is not in proposal to be drawn as a closed polyline on this layer.
Shortcut Command:
NIP
How to draw :
Not In Possession:
54
PreDCR User Guide : Municipal Corporation Greater Mumbai
Following rules will be applied to Not in Possession layer
Deduction from plot
Net Plot Calculations
Precautions to be taken –
Draw a closed polyline correctly and provide text inside it.
PreDCR Layer Information 55
Layer: _Parking
Description :
Draw a parking poly as a closed polyline which is an enclosed covered or open area sufficient in size to park vehicles. This closed polyline shall contain a text on same _Parking layer. This text is treated as name of parking. Insert the parking by using an Insert-> parking option.
Shortcut Command :
PK
Parking Name:
This closed polyline shall contain a text on same _Parking layer. This text is treated as name of parking.
On this layer, you can group and insert any number of parking
Parking Name
Car Large
Car Small
Scooter
Cycle
Transportation vehicle
Visitor's Large Car
CP-L
CP-S
SC
CY
TV
VP-L
55
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 56
Visitor’s Small Car
Visitor’s Scooter
Visitor’s Cycle
Ambulance
VP-S
VSC
VCY
AMB
How to Draw :
Parking:
Following rules will be applied to Parking layer
No of Parking
Size of Parking
Type of Vehicles
Precautions to be taken –
Draw a closed polyline correctly with text on same layer where stilt area is proposed.
Insert various type of parking’s from Insert option from PreDCR Menu
If this polyline has not been drawn and inserted correctly then no of proposed parking’s will not come proper.
Layer: _Passage
Description :
A closed polyline on _Passage represents a passage. It is a common passage or circulation space including a common entrance hall. This closed polyline contain a text. This text must be on
"_Passage" layer. This text is treated as name of closed polyline.
Lift lobbies to be drawn on same layer and to be marked it as Paid by using mark option from
PreDCR menu.
Shortcut Command :
PAS
How to draw:
56
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 57
Passage:
Following rules will be applied on the objects of Passage layer
Passage Width
Deduction from BUA
Addition in BUA
Precautions to be taken –
Draw a closed polyline correctly and mark it by using mark option from predcr menu...
If lift lobby / staircase lobby to be marked free from FSI as Paid.
Remaining Passage area to mark Taken in FSI.
Layer: _Pathway
Description :
Draw Pathway as a closed polyline with text specifying its width.eg.1.5 m. wide pathway.
Shortcut Command:
R6
How to draw :
Pathway:
Following rules will be applied on the objects of Pathway layer
Length
Width
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
57
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 58
Layer: _PhasedProgram
Description:
Draw phased program outlines covering floor plans or buildings/pworks on '_PhasedProgram' layer inside plot or floor. Enter name/number of Phased program -
E.g. Phase-1, phase-2, phase-3, phase4 etc.
Shortcut Command:
POD
Layer: _PrintAdditionalDetail
Description:
Apart from the layers specified by PreDCR, any other information which user wants to display in final approval print shall be drawn on _PrintAdditionalDetail layer
Shortcut Command:
ADET
How to draw:
58
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 59
Layer: _Podium
Description :
Podium shall be drawn on '_Podium' layer as a closed polyline. Podium should be inside plot covering proposed works if any.
Shortcut Command:
POD
How to draw :
Podium:
Following rules will be applied to Podium layer
Parking between podium to plot boundary Distance check
59
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 60
Layer: _PropWork
Description :
Proposed Work is a building profile/outline and shall be drawn inside plot. All detail Building plans (inside building polyline) of all PWork (inside plot polyline) is associated/linked automatically by Auto-DCR by matching its name.
So for proper association it is required to follow specific standard as given.
XY (Z)
X is Wing name.
Y is wing number.
Z is Building name.
For example if there are four wings A1,A2 & B1,B2 in building named "Monarch" then proposed work names shall be -
A1 (Monarch), A2 (Monarch)
B1 (Monarch), B2 (Monarch)
Reference Circle: All PWork polies must contain two circles (of any size) with its center on common point for whole building. First on layer of any FSI and second on Layer “_Floor”. These reference circles to be inserted from PreDCR -> insert-->Direction ref circles at the same location in all the floors as well as pwork in plot. Usually they can be placed inside either Common
Liftwell or Stair/Inner Chowk (because generally their location is same on all floors). Reference circles are used by the software for overlapping all floor plans.
Shortcut Command:-
PW
How to draw :
PropWork:
Following rules will be applied to PropWork layer
Building location in Plot boundary
Coverage area
Building to Building distance
Propwork to parking distance
Electrical line distance
electric sub-station distance
Septic tank
covered garage distance
Rail line distance
Precautions to be taken –
Draw poly line properly and assign name from PreDCR menu Assign Name option Building &
PropWork.
If building and proposed work not linked properly then it will hamper to building rules.
60
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 61
Layer: _RailLine
Description :
Railway line shall be drawn as a non closed polyline with some text indicating gauge of rail line over it.
Shortcut Command :
L2
How to draw :
RailLine:
Following rules will be applied to Rail line layer
Gauge
Margin
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
61
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 62
Layer: _Ramp
Description :
Draw a Ramp poly as a closed polyline in floor plans and/or plot and section. Naming convention for ramp is "---m. long and ---m. high ramp-1". Give unique name to each ramp.
Shortcut Command :
RP
How to draw :
Ramp:
Following rules will be applied on the objects of Ramp layer
Width
Slope
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
62
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 63
Layer: _Recreational Ground
Description :
Draw Recreational Ground as closed polyline reserved as recreational space on this layer. With text on same layer.
Shortcut Command:
OPS
How to draw :
Recreational Ground:
Following rules will be applied on the objects of recreational ground layer
Balance plot
Deduction in area calculation
Minimum recreation ground area
Plot area in side recreation ground
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
63
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 64
Layer: _Refuge Area
Description :
Refuse area to be drawn in plan as a closed polyline with text on this layer. Overlapped with FSI layer but outside the FSI poly.
Shortcut Command :
RFGA
How to draw :
Refuge Area:
Following rules will be applied on the objects of Refuge Area layer
Area
Width
Excess are to be count in BUA
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
64
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 65
Layer: _RefuseChember
Description :
Refuse chamber to be drawn in plan as a closed polyline with text on same layer which should be inside of floor.
Shortcut Command:
RMB
Layer: _RefuseChute
Description :
Refuse chute to be drawn in plan as a closed polyline with text on same layer which should be inside of floor.
Shortcut Command:
RFC
Layer: _ReservArea
Description :
65
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 66
Reserved area (Reservation area in Development plan) shall be drawn on this layer if present in proposal. This can be any area reserved for/by Authority for future.
Shortcut Command :
RSA
How to draw :
ReservArea:
Following rules will be applied to Reserve Area layer
Reserve area
Deduction
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
Layer: _ResiOuterWall
Description :
Draw a Residential Outer Wall as a closed polyline which is the area covered by a building on all the floors. This polyline only used for residential use building or floor. This layer must be inside
Floor poly.
Shortcut Command :
MFS
How to draw :
ResiOuterWall:
66
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 67
Following rules will be applied for the same.
Residential built up area calculations
Permissible FSI
Permissible architectural projection
Converge check
Use of building
Precautions to be taken –
Draw a closed poly line correctly where commercial building is proposed.
Ploy line must be inside of _Floor layer.
Layer: _Road widening
Description :
Draw a road widening polyline as a closed polyline which the plot area is going to the road, that area should be drawn on this layer. It should be inside the plot polyline.
Shortcut Command :
R5
How to draw :
RoadWidening:
Following rules will be applied to Road Widening layer
Calculation of net Plot
Widening of Road
Precautions to be taken –
Draw a closed polyline correctly inside Main plot and give text on same layer.
67
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 68
Layer: _Room
Description :
A closed polyline on _Room layer represents a room. This closed polyline contain a text. This text must be on _Room layer. Room to be marked by assigning them names using Assign Name-> room option from PreDCR menu.
Shortcut Command :
RU
How to draw :
Room:
Following rules will be applied on the objects of room layer
Room size
Width
Depth
Door
ventilation
Balcony
Projection
Precautions to be taken –
Draw poly line properly and give name to this object from “Assign Name → “ROOM”
Room must be inside carpet area poly line and door and windows must be overlapped with it.
If it is Air-Conditioned room then can be marked by using Mark option from PreDCR menu.
68
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 69
Layer: _Right-of-way
Description :
Draw a closed polyline on “_Right-of-way” to represent a Right Of way and text inside it representing its width. Layer should be inside or intersecting with Plot poly
Shortcut Command :
ROW
How to draw :
Right-Of-Way:
Following rules will be applied on the objects of Right-of-way layer
Width
Plot
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get check.
69
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 70
Layer: _Sanitation
Description :
Draw any sanitation entities on this layer. (E.g., Kitchen sinks etc...) Mark those entities by using
PreDCR -> Insert -> Sanitation.
Shortcut Command :
SNT
How To Draw:
70
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 71
Layer: _Service Duct
Description :
Draw a closed polyline in floor plan, area is left for services shaft like Electrical ducts, Fire ducts, etc. to be drawn on “Service Duct” layer.
Shortcut Command:
SD
How to draw :
Service Duct:
Precautions to be taken –
Draw a closed poly line on Service Duct layer with text on same layer.
It should inside floor plan
71
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 72
Layer: _Section
Description :
Draw a Section polyline as a closed poly of section boundary which contain all floors with stair cabin, Lift well machine room, water tanks etc. as shown in the figure. Also write the name as
"Section" in this section poly.
In this closed poly of section draw sections of all floors with stair cabin, inner Chowk, Lift well machine room, Ventilation shaft, water tanks etc. as shown in the figure.
Also write the name as "Section" in this section poly.
This section poly will present inside the building poly.
Shortcut Command :
SEC
How to draw :
Section:
Following rules will be applied on the objects of Section layer
Name
All Floor in section
Ground level
Lift well height
Staircase cabin
Margin
Tenement number
Parking
Per floor area
Building height
72
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 73
Water tank
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get check.
Layer: _Sewage Line
Description:
Drain Line shall be drawn as a open polyline on this layer.
Shortcut Command :
L5
How to draw :
73
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 74
Layer: _Service Slab
Description:
Service slab to be drawn as a closed polyline on “_ServiceSlab” layer with containing text on same layer.
Layer: _Site Plan
Description:
Site plan if any to be drawn on this layer. This is only for reference. No verifications are done by
AutoDCR for this layer. So not compulsory.
Shortcut Command:
STP
Layer: _SmokeVent
Description :
Smoke Vents are installed in buildings as an active fire protection measure. They are openings in the roof which are intended to vent the heat and smoke developed by a fire inside the building by the action of buoyancy. Such area to be drawn on “_Smoke Vent” layer as closed poly line.
Shortcut Command :
SMV
Layer: _SpecialUseOuterWall
Description :
Building for all other uses like educational, institutional etc. except Residential, Commercial &
Industrial use should be drawn on this layer.
Shortcut Command :
SUF
How to draw :
Special Use Outer Wall:
Following rules will be applied for the same.
Special use built up area calculations
Permissible FSI commercial BUA in mixed use
74
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 75
Permissible architectural projection
Converge check
Use of building
Precautions to be taken –
Draw a closed poly line correctly where commercial building is proposed.
Ploy line must be inside of _Floor layer.
Layer: _Staircase
Description :
Staircase: On this layer, Each Staircase poly shall have three lines for Flight Width, Intermediate
Landing and Floor Landing on same layer. Mark these open polyline by using Mark-> Staircase option from PreDCR menu. Also draw in plan all the treads on this layer which is a open polyline.
This closed polyline contains a text. This text must be on _Stair layer. This text is treated as name of closed polyline. On this layer, Each Staircase poly shall have three lines for Flight Width,
Intermediate Landing and Floor Landing on same layer This can be mark by tool Mark >
Staircase > intermediate landing etc.
Shortcut Command :
STR
How to draw :
Staircase:
Following rules will be applied on the objects of staircase layer
Staircase area
75
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 76
Tread width
No. On Flight
Rise height
Staircase landings
No of Risers
Ventilation
Free from FSI (paid & unpaid)
BUA calculation
Access to floor
Precautions to be taken –
Draw a closed polyline correctly and mark it by using Mark option from PreDCR menu.
Mark Stair case landings, flight width from PreDCR menu.
Mark stair case if it is free from FSI or taken in FSI.
Layer: _SubDivision
Description :
In Subdivision one plot is divided into more than one Subdivision.
All entities having subdivision as their container entity should be uniquely present in all
Subdivisions of a Plot i.e. suppose there is a road widening in the Plot then the poly of road widening should be different for each Subdivision (subdivided plot).
Ex. Here Plot 1 is divided into three Subdivisions. And also the Road Widening is divided into
RoadW 1 and RoadW 2 for each Subdivision.
(for subdivision, draw plot 1 on plot layer and subdivided plots like SubDiv 1,SubDiv 2 &
SubDiv 3 on sub-division layer overlapping plot 1.)
Shortcut Command :
SBD
How to draw :
Subdivision:
Following rules will be applied on the objects of Subdivision layer
76
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 77
Name
Plot area
Recreation ground
Amenity
RoadWidening
Pathway
Internal road
Main road
Reserve area
Right-Of-Ways
NotInPossession
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
Layer: _SubStructure
Description :
Draw various substructures on "_SubStructure" layer as a closed polyline. And mark it according to the requirement as Mark -> Substructure -> Society Office, from PreDCR menu. Substructures can be drawn inside plot or in floor plans.
Shortcut Command :
SSTR
How to draw :
Substructure:
Following rules will be applied on the objects of Substructure layer
77
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 78
Distance from building
Deduction or addition in BUA
Size of Substructure
Allowed in margin Front, Rear, Side
Distains from main road
Distains from Plot boundary
Distains from Building
Precautions to be taken –
Draw polyline correctly.
Give name to this object from “Mark → Projection” option (From PreDCR Menu).
If this object has not been marked properly then it won't be checked.
Layer: _SurrenderToCorpo
Description :
In case of accommodation reservation, the plot area or FSI to be surrendered to MCGM is to be drawn on this layer with text inside it.
Shortcut Command :
STC
How to draw :
Surrender To Corpo:
Following rules will be applied on the objects of Surrender To Corpo layer
Depend on Gross plot area
Reserve area for mcgm
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
78
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 79
Layer: _SurrenderToMhada
Description : -
In case of accommodation reservation, the plot area or FSI to be surrendered to MCGM is to be drawn on this layer with text inside it.
Shortcut Command :
STM
How to draw :
Surrender To Mhada:
Following rules will be applied on the objects of SurrenderToMHADA layer
Depend on Gross plot area
Reserve area for mcgm
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
79
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 80
Layer: _Tank
Description :
A closed polyline on _Tank layer represents a water tank. Under Ground tank can be drawn in
Floor or Layout plan. If it is drawn in Floor plan then it should be at bottom of GROUND FLOOR.
Overhead tank can be drawn in TERRACE FLOOR. Tank should be drawn as per internal size or dimensions. Both the tank also draw in section also.
Tank Name: - This closed polyline contain a text and must be in given format. This can also be done by tool Assign Name>Tank
Tank Name+ Type +Capacity
Tank Type
Overhead water tank
Underground water tank
Text
(O/H)
(U/G)
For e.g.
TANK-1 (O/H)
TANK-2 (U/G)
Under Ground tank can be drawn in Floor or Layout plan. If it is drawn in Floor plan then it should be at bottom of GROUND FLOOR.
Overhead tank can be drawn in TERRACE FLOOR. Usually it is drawn on Staircase poly in
TERRACE FLOOR.
80
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 81
Shortcut Command :
TNK
How to draw : -
Tank:
Following rules will be applied on the objects of Tank layer
Tank area
Width
Depth
Capacity
Precautions to be taken –
Draw poly line properly and give name to this object from “Assign Name → “TANK” Option?
If this polyline has not been drawn and named correctly then all above rules will not get check.
Layer: _Temp Structure
Description:
Area for temporary structures to be drawn as closed polyline with text on this layer
Shortcut Command :
TMPS
How to draw :
Temp Structure:
Following rules will be applied on the objects of Temp Structure layer
Area check
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
81
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 82
If this polyline has not been drawn and named correctly then all above rules will not get checked.
Layer: _Terrace
Description:
Draw a Terrace as a closed polyline on _Terrace layer which is including parapet wall.
If Individual terrace having slopped, then slop shall be mentioned in its text. E.g. 1:5 slopping terrace, etc.
Terrace can be present in:
Shortcut Command :
TER
Plot: It must overlap with Proposed Work
Floor: It must be outside the outer Wall.
How to draw : -
Terrace:
Following rules will be applied on the objects of Terrace layer
Addition
AlterNet terrace
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
82
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 83
Layer: _Tree
Description:
Draw or insert Tree in plot on _Tree layer if it is present in plot.
User can be insert tree block directly by using predcr menu bar insert option.
Shortcut Command:
TREE
Layer: _UpperSetBack
Description :
Draw a closed polyline in plan as well as in proposed work which having setbacks
Shortcut Command :
USB
How to draw :
Upper Set Back:
Following rules will be applied on the objects of Upper Set Back layer
Margin
Precautions to be taken –
Draw poly line properly and give name to this object from “MARK → “UpperSetBack” Option?
If this polyline has not been drawn and named correctly then all above rules will not get check.
83
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 84
Layer: _Void
Description :
If the space is not Chowk then it can be void. All ducts (where ventilation is not taken) and double height rooms can be drawn in void layer. If room is double heighted then void to be drawn on above of room at upper level floor.
Shortcut Command :
VD
How to draw :
Void:
Following rules will be applied on the objects of Void layer
Calculation of BUA
Double height of room.
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above rules will not get checked.
84
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 85
Layer: _WaterLine
Description :
Draw a Water line as an open polyline to show Water supply.
Shortcut Command :
WL
How to draw :
85
PreDCR User Guide : Municipal Corporation Greater Mumbai
PreDCR Layer Information 86
Layer: _Window
Description :
Window is a closed Polyline which is drawn on "_Window" layer. Also you can insert a particular size poly for Window using Insert->Window from PreDCR menu.
Shortcut Command :
WND
How to draw :
Window:
Following rules will be applied on the objects of Window layer
Width
Length
Height
Ventilation
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer from “insert “option as that of object
If this polyline has not been drawn and named correctly then all above rules will not get checked
86
PreDCR User Guide : Municipal Corporation Greater Mumbai
Tools
All/Remover Tool Tip (PDCRTOOLTIP):
This command will activate the tool tips for PreDCR layers
.
Show Only DCR Layers (PDCRSPL):
This command will turn off all the layers in the drawing except PreDCR layers.
Show Only DCR Layers (PDCRSDL):
This command will turn off all the layers in the drawing except DCR layers.
Show Other Layers (PDCRSOL):
This command will turn off all the DCR and PreDCR layers in the drawing.
Show all layers (PDCRSAL);
This command will turn on all layers in the drawing.
Calculate Total Area (PDCRCTA):
This command will compute the total area of all selected closed polygons.
Calculate Deducted Area (PDCRCDA):
This command will compute the area of closed polygon after deducting closed polygons found inside.
Tools 87
87
PreDCR User Guide : Municipal Corporation Greater Mumbai
Get All Inside Poly (PDCRFIP):
This command will highlight all polygons, which found exactly inside selected polygon under test.
Get All Overlapping Poly (PDCRGOP):
This command will highlight all polygons, which are overlapping with selected polygon under test.
Get All Intersecting Poly (PDCRGIP):
This command will highlight all polygons, which are intersecting with selected polygon under test.
Find Open Entities (PDCRFNDO):
Highlight open entities on PreDCR layers.
Find Closed Entities (PDCRFNDC):
Highlight closed entities on PreDCR layer.
Shortest distance (PDCRFSD):
This command will find the shortest distance between two entities.
Spelling check (_spell):
This tool is used for spelling checking.
Find Object (PDCRFOBJ):
This command zoom & highlight object of a given handle.
88
PreDCR User Guide : Municipal Corporation Greater Mumbai
Tools 88
Set Default ACAD Version (PDCRSDA):
Tools 89
89
PreDCR User Guide : Municipal Corporation Greater Mumbai
Commands
Create New Project (PDCRNWP)
This command will Create New project for current drawing.
Here you have to select Type of Project as
Proposed Development.
Note: It is always compulsory to add your drawing to new Project.
Create AutoDCR Layers (PDCRCL):
This command will create layers required for AutoDCR and as per the Project Type you have selected.
Verify Drawing:
This command will verify the current drawing as required by DCR specifications.
a) Verify Close Entities (PDCRVD): Verify that LWPOLYLINE entities on the selected layers are closed and contain one text.
Commands 91
B) Verify all drawing (PDCRVT): Use this command to verify the layout and building level objects in the current drawing plan.
Major checks are as follows:
In the "Verify All Drawing Dialog" you can select the layout or building objects to be checked. Then to view the result press OK button. PreDCR will start checking all corresponding objects in the currently open drawing and then display the status as OK or list of failed objects in the dialog as shown in
PreDCR help manual: Municipal Corporation Greater Mumbai
Markings: 92
Figure. Failed Object Information.
Check if these entities are drawn as closed LWPOLYLINE.
Name text is given to all objects.
Entities are placed exactly inside their parent objects (container).
Naming conventions are followed properly.
c) Objection List (PDCROLST): This command gives the list of all minimum required entities which are not there in your drawing. If all required entities found then it gives a message that “minimum required entities are present in drawing”.
Markings:
Marking adds some extra meaning in entity. Following commands are provided to mark different entities as per requirement.
Proposed Work:
Centrally Air-Conditioned:
If building is containing centrally Air-Conditioned then marked proposed work by using this menu.
Normal:
If by mistake proposed work is marked centrally Air-Conditioned then can be marked Normal by using this menu.
Amenity:
Surrendered:
If Amenity area is surrendered to corporation then can be marked by using this menu.
Normal:
If by mistake Amenity is marked Surrendered then can be marked Normal by using this menu.
Recreational Ground:
Paved:
Mark Recreational ground area if it is paved by using this menu.
Normal:
Mark Recreational ground area if it is not paved by using this menu.
Floor in Section:
Slab Thickness:
Mark slab thickness to Floor In section layer by using this menu.
Beam:
Mark Beam to floor in section layer by using this menu.
TDR:
Mark TDR floor by using this menu.
Read Widening:
Mark Road widening area in floor in section by using this menu.
PreDCR help manual: Municipal Corporation Greater Mumbai
Markings: 93
Normal:
If by mistake floor in section is marked then can be marked Normal by using this menu.
Stair Case:
No of flight:
3, 4, flights: Mark stair case if it is greater than 2 flights accordingly.
Fire Escape Staircase
(PDCRSCFAB): Mark line inside staircase as a fire escape staircase
Fab /Spiral Staircase
(PDCRSCFAB): Mark line inside staircase as a Fabricated or spiral staircase.
Free from FSI (Paid or Unpaid)
(PDCRSCES): Mark free from FSI paid or unpaid
Taken in FSI
(PDCRSCES): Mark staircase taken in FSI.
Open Staircase Free from FSI
: Mark open stair case as free from FSI.
Open Staircase Taken in FSI
: Mark open stair case taken in FSI.
Escalators:
Mark stair case poly if Escalator is proposed.
Stair case landing:
Intermediate Landing
(PDCRMIL): Mark line inside staircase as intermediate Landing.
Flight Width
(PDCRMFW): Mark line inside staircase as Flight Width
.
Floor Landing
(PDCRMFL): Mark line inside staircase as Floor Landing.
Lift:
Normal (Default) Free from FSI or Taken in FSI
(PDCRSCES): Mark Lift well poly line Normal Free from FSI or Taken in FSI accordingly.
Fire Lift well
(PDCRSCES)
:
Mark Fire Lift well as a provided.
Hydraulic- Free from FSI OR Taken in FSI
(PDCRSCES): Mark Hydraulic as a Free from FSI OR Taken in FSI
Car Lift- Free from FSI OR Taken in FSI
Mark Car Lift as a Free from FSI OR Taken in FSI.
Lift Machine Room:
Free from FSI or Taken in FSI: Mark Lift machine room as a Free from FSI OR Taken in FSI
Passage:
Covered Passage: Free from FSI
(PDCRPOCP): Mark a passage as a Covered passage Free from FSI or taken
PreDCR help manual: Municipal Corporation Greater Mumbai
Markings: in FSI.
Taken in FSI
(PDCRPSUP): Mark passage as a taken in FSI.
Open corridor
(PDCRPSUP): Mark passage as a open corridor
Fire Escape Passage
: Mark Passage as Fire Escaped.
Unmark (Default)
(PDCRPSUP): Mark passage as a Normal Passage
FSI (Outer Wall):
Road Widening
(PDCRCONES): Mark Residential or Commercial FSI as Road widening areas FSI.
TDR
(PDCRCONES): Mark Residential or Commercial FSI as TDR.
Existing
(PDCRCONES): Mark Residential or Commercial FSI as Existing FSI.
Normal (Default)
(PDCRUMFSI): Mark Residential or Commercial FSI as Normal FSI.
Carpet Area:
Splitted Tenement (
PDCRMSPLTT): Mark Carpet Area as Splitted tenement.
Rehab
: Mark Carpet Area as a rehab and enter existing owner name, carpet area, common area, flat no, etc.
Sale:
Mark Carpet area as Sale.
Project Affected Portion
(PDCRMCPAP): Mark Carpet area if it is affected by projection (PAP).
Normal (default)
(PDCRMSPLTT): Mark Carpet Area as Normal (default)
Room:
A.C. Room or Normal default
(PDCRMENCBL): Mark-> Room A.C.room or Normal (default).
Balcony:
Enclosed Balcony
(PDCRMENCBL): Mark Balcony as enclosed balcony.
Fire Balcony
(PDCRMFB): Mark Balcony as Fire balcony
Unmark (Default)
(PDCRUMENCBL): Mark an open or dry balcony by using this menu.
Terrace:
Taken In FSI
(PDCRMRTER): Mark Terrace as taken in FSI.
PreDCR help manual: Municipal Corporation Greater Mumbai
94
Markings:
Normal (default)
(PDCRMNTER): Mark Terrace as default.
Column:
Floating
(PDCRMCF): Mark column if it is floating.
Column (Default)
(PDCRMCD): Mark column as default.
Parking
Tow stacked:
Mark individual parking if it is two stacked.
Three stacked:
Mark individual parking if it is three stacked.
Four stacked:
Mark individual parking if it is four stacked.
Five Stacked:
Mark individual parking if it is Five stacked.
Six Stacked:
Mark individual parking if it is six stacked.
Projection:
F.Bed
(PDCRMBPROJ): Mark Projection as Flower Bed.
Chhajja:
Mark Projection as Chhajja.
Cornice:
Mark Projection as Cornice.
Whether shade
: Mark Projection as Whether shade.
Pargola:
Mark projection as Pargola.
Loft
(PDCRMLPROJ): Mark Projection as Loft in floor plan as well as in section.
Canopy
(PDCRMCBPROJ): Mark Projection as Canopy
Porch
(PDCRMCPROJ): Mark Projection as Porch
Revas Projection
(PDCRMCPROJ): Mark Projection as a Revas Projection.
Garbage shaft
(PDCRMVPROJ): Mark Projection as a Garbage shaft.
Ornamental Projection
(PDCRMVPROJ): Mark Projection as a Ornamental Projection.
Ornamental Glazing
(PDCRMOPROJ): Mark Projection as a Refuse Chute.
Otta
(PDCRUMPROJ): Mark Projection as a Otta as a provided
Steps
(PDCRUMPROJ): Mark Projection as a Steps as a provided
PreDCR help manual: Municipal Corporation Greater Mumbai
95
Markings:
Road Widening:
Taken in FSI
(PDCRMRVIFSI): Mark a Road widening area as a Taken in FSI
Unmark (default):
Mark Road widening area as normal.
Upper Setback:
First upper setback
(PDCRUMMR): Mark Upper setback as a first upper setback
by using this menu
Second upper setback
(PDCRUMMR): Mark Upper setback as a Second upper setback by using this menu.
Existing Structure:
To Be Retained:
Building or Substructure: Mark Existing structure layer as to be Retained Building or
Substructure.
To be demolished:
Mark Existing structure as to be demolished.
Substructure:
Electric Meter Room
(PDCRMER): Mark Substructure as an Electric meter room.
Electric Sub-Station
: Free from FSI or Taken in FSI (PDCRMTRAN): Mark Sub Structure as an electric Sum-
Station ->Free from fsi or taken in fsi
Watchman Cabin
(PDCRMTRAN): Mark Sub Structure as a watchman cabin
Society Office
(PDCRMOR): Mark Sub Structure as a Society office.
Servant Room
(PDCRMSQ): Mark Sub Structure as a servant quarter.
Servant Toilet
(PDCRMSQ): Mark Sub Structure as a servant quarter.
Sanitary Block
(PDCRMSB): Mark Sub Structure as a sanitary block.
Covered Garage
(PDCRMGRJ): Mark Sub Structure as a covered garage when garage is covered.
Open Garage
(PDCRMGRJ): Mark Sub Structure as a Open garage
Rain Water harvesting
(PDCRMGRJ): Mark Sub Structure as a Rain Water harvesting
A.C Plant Room
(PDCRMGRJ): Mark Sub Structure as a A.C Plant Room
AHU
(PDCRMGRJ): Mark Sub Structure as a AHU
Covered Swimming Pool
(PDCRMGRJ): Mark Sub Structure as a Covered Swimming Pool
Uncovered Swimming Pool
(PDCRMGRJ): Mark Sub Structure as a Uncovered Swimming Pool
Fire Control Room:
Mark a substructure as a Fire control room.
PreDCR help manual: Municipal Corporation Greater Mumbai
96
Markings: 97
Boiler Room:
Mark a substructure as a Boiler room.
Septic Tank/Soak pit
(PDCRMGRJ): Mark Sub Structure as a Septic Tank/Soak pit
Pump House
: Free from fsi or taken in fsi (PDCRMPR): Mark Sub Structure as a Pump House Free From fsi or taken in fsi
Effluent Treatment Plant/ STP
(PDCRMETP): Mark Sub Structure as a Effluent Treatment Plant /STP
Dish Antenna room
(PDCRMSPT): Mark Sub Structure as a Dish Antenna room
Well
(PDCRMSPT): Mark Sub Structure as a Will
Telephone Installation room
Free from fsi or taken in fsi (PDCRMSPT): Mark Sub Structure as a Telephone
Installation room Free from fsi or taken in fsi
Entrance gate
(PDCRMSPT): Mark Sub Structure as a Entrance gate
Fitness center
(PDCRMSPT): Mark Sub Structure as a Fitness center
Suction Tank
(PDCRMSPT): Mark Sub Structure as a Suction tank
Pavilion
(PDCRMSPT): Mark Sub Structure as a Pavilion
Gymnasium
(PDCRMSPT): Mark Sub Structure as a Gymnasium
Club-House
(PDCRMSPT): Mark Sub Structure as a Club-House
Dust bin
(PDCRMSPT): Mark Sub Structure as a Dust bin
Milk/ Telephone booth
-> Free from fsi or taken in fsi (PDCRMSPT): Mark Sub Structure as a Milk/
Telephone booth-> Free from fsi or taken in fsi
Letter Box
Free from fsi or taken in fsi (PDCRMSPT): Mark Sub Structure as a Letter Box-> Free from fsi or taken in fsi
Chimney
Free from fsi or taken in fsi (PDCRMSPT): Mark Sub Structure as a Letter Box-> Free from fsi or taken in fsi
Welfare Hall
: Mark a substructure as a Welfare Hall.
BalWadi:
Mark a substructure as a balwadi.
Driver’s Rest Room:
Mark a substructure as a Driver’s Rest Room.
D.G. Set Room:
Mark a substructure as a DG Set Room.
Dispensary:
Mark a substructure as a Dispensary.
Store Room:
Mark a substructure as a Store Room.
Bank Locker/Safe Deposit:
Mark a substructure as a Bank Locker or Safe Deposit.
Meter Panel Room:
Mark a substructure as a Meter Panel Room.
PreDCR help manual: Municipal Corporation Greater Mumbai
Markings:
Change of Use:
If use of any floor is changed then mark FSI polyline of that floor as change of use- changed use
(e.g. residential, commercial etc) Draw FSI on changed use FSI layer (e.g if changing use from residential to commercial then draw FSI polyline on _CommFSI layer and mark FSI as change of use commercial.
If use of entire building is changed then mark pwork similarly.
Residetional
(PDCRMFRESI): Mark FSI poly to change of use of floor as Residetional.
Industrial
(PDCRMFIND): Mark FSI poly to change of use of floor as Industrial
Educational
(PDCRMFEDU): Mark FSI poly to change of use of floor as Educational.
Commercial
(PDCRMFCOM): Mark FSI poly to change of use of floor as Commercial.
Assembly (
PDCRMFASM): Mark FSI poly to change of use of floor as Assembly.
Institutional
(PDCRMFINS): Mark FSI poly to change of use of floor as Institutional.
Mercantile
(PDCRMFMER): Mark FSI poly to change of use of floor as Mercantile.
Govt/Semi-Public (
PDCRMFGOVT): Mark FSI poly to change of use of floor as Govt/Semi-Public.
Pvt. Business
(PDCRMFPVT): Mark FSI poly to change of use of floor as Pvt. Business.
Utility
(PDCRMFUTL): Mark FSI poly to change of use of floor as Utility.
Services
(PDCRMFSER): Mark FSI poly to change of use of floor as Services.
PropWork
Residetional
(PDCRMPRESI): Mark PropWork poly to change of use as Residetional.
Industrial
(PDCRMPIND): Mark PropWork poly to change of use as Industrial.
Educational
(PDCRMPEDU): Mark PropWork poly to change of use as Educational.
Commercial
(PDCRMPCOM): Mark PropWork poly to change of use as Commercial.
Assembly
(PDCRMPASM): Mark PropWork poly to change of use as Assembly.
Institutional
(PDCRMPINS): Mark PropWork poly to change of use as Institutional.
Mercantile
(PDCRMPMER): Mark PropWork poly to change of use as Mercantile.
Govt/Semi-Public
(PDCRMPGOVT): Mark PropWork poly to change of use as Govt/Semi-Public.
Pvt. Business
(PDCRMPPVT): Mark PropWork poly to change of use as Pvt. Business.
Utility
(PDCRMPUTL): Mark PropWork poly to change of use as Utility.
PreDCR help manual: Municipal Corporation Greater Mumbai
98
Insert entities
Services
(PDCRMPSER): Mark PropWork poly to change of use as Services.
Margin
(PDCRMRGN): Use this command to define or mark the front, sides and rear margins of the plot. .
99
Insert entities
Parking
Car L
(PDCRICP): Use this command to insert car-parking poly of. At selected point.
Car S
(PDCRICP): Use this command to insert car-parking poly of. At selected point.
Scooter
(PDCRISP): Use this command to insert Scooter parking poly at selected point.
Cycle
(PDCRICY): Use this command to insert Cycle parking poly at selected point.
Transport Vehicle
(PDCRITV): Use this command to insert parking Transport Vehicle poly at selected point.
Visitors Parking
-
Car -L
(PDCRIVPL): Use this command to insert visitor large car parking poly at selected point
Visitors Parking- Car -S
(PDCRIVPS): Use this command to insert visitor small car parking poly at selected point
Visitors Parking- Scooter
(PDCRIVSC): Use this command to insert visitor scooter parking poly at selected point.
Visitors Parking- Cycle
(PDCRIVCY): Use this command to insert visitor Cycle parking poly at selected point
Ambulance
(PDCRIVP): Use this command to insert Ambulance parking poly at selected point
Mini Bus
: Use this command to insert Mini Bus parking poly at selected point
Big Bus
: Use this command to insert big Bus parking poly at selected point
PreDCR help manual: Municipal Corporation Greater Mumbai
Insert entities 100
Door
(PDCRIDRNAM): Use this command to insert door poly at selected point and with specified size given by user. As soon as you use this command the following Dialog appears.
Window
(PDCRIWNDNAM): Use this command to insert window poly at selected point and with specified size given by user.
Sanitation Text
Use this command to insert sanitation text at selected point. Ex. , Urinal, Wash basin
Drinking water, washing tap, etc. which is mark on then insert text by using sanitation text marking from insert menu.
Direction Reference Circle
(PDCRIWC): Use this command to insert direction reference circle. Insert these circles in all the floor plans as well as in proposed work at the same & common place (e.g. Liftwell or Stair) of all the floors.
North Direction
(PDCRINND): Use this command to insert North Direction. Insert North Direction indicating the sides of your plot. You have to rotate this as per North Side.
Stair Case Up/Dn Direction
:
UP
(PDCRISDAUP): Use this command to insert showing direction of Stair Case way is UP.
PreDCR help manual: Municipal Corporation Greater Mumbai
Down
(PDCRISDADN): Use this command to insert showing direction of Stair Case way is down.
Building Template:
You can insert building template by using this command as shown in below screen.
101
Following template will automatic generate.
Assign Name
There are few naming conventions required by AutoDCR, for which PreDCR provides the following tools:
Building and proposed works
(PDCRBLDPWNL): Use this command to give name for building poly and its associated proposed works.
PreDCR help manual: Municipal Corporation Greater Mumbai
Assign Name
Tank
(PDCRTNKNAM): Use this command to give name for Tank poly and its corresponding tanks.
Fill in the dialog and select the tank poly drawn in plan and the same drawn in section
Room
(PDCRASRUN): Use this command to give different names for Room poly.
102
PreDCR help manual: Municipal Corporation Greater Mumbai
Tools
Floor Name
(PDCRASFLRNAM): Use this command for assigning name to a floor poly and its corresponding floor in section poly in section.
103
Tools
All/Remover Tool Tip (PDCRTOOLTIP):
This command will activate the tool tips for PreDCR layers.
Show Only DCR Layers:
All PreDCR layers (PDCRSPL):
This command will turn off all the layers in the drawing except PreDCR layers.
Building level layer (PDCRSBL):
This command will turn on all the building plan level layers in the drawing.
Layout level layer (PDCRSLL): This command will turn on all the Layout plan level layers in the drawing.
Show Only DCR Layers (PDCRSDL):
This command will turn off all the layers in the drawing except DCR layers.
PreDCR help manual: Municipal Corporation Greater Mumbai
Tools
Show Other Layers (PDCRSOL):
This command will turn off all the DCR and PreDCR layers in the drawing.
Show all layers (PDCRSAL);
this command will turn on all layers in the drawing.
Calculate Total Area (PDCRCTA):
This command will compute the total area of all selected closed polygons.
Calculate Deducted Area (PDCRCDA):
This command will compute the area of closed polygon after deducting closed polygons found inside.
104
Get All Inside Poly (PDCRFIP):
This command will highlight all polygons, which found exactly inside selected polygon under test.
Get All Overlapping Poly (PDCRGOP):
This command will highlight all polygons, which are overlapping with selected polygon under test.
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS 105
Get All Intersecting Poly (PDCRGIP):
This command will highlight all polygons, which are intersecting with selected polygon under test.
Find Open Entities (PDCRFNDO): Highlight open entities on PreDCR layers.
Find Closed Entities (PDCRFNDC): Highlight closed entities on PreDCR layer.
Shortest distance (PDCRFSD):
This command will find the shortest distance between two entities.
Spelling check (_spell): This tool is used for spelling checking.
Find Object (PDCRFOBJ): This command zoom & highlight object of a given handle.
Set Default ACAD Version (PDCRSDA): If you select by default any AutoCAD version and wants to use in another AutoCAD version then by using this command you can remove set default AutoCAD version option.
PREDCR SHORT-CUT COMMANDS
Layer name
_Amalgamation
Description
Draw a continuous poly around the plots you want to amalgamate.
Amalgamation contains more than one plot amalgamated together.
All entities having amalgamation as their container entity should be uniquely present in each amalgamation.
Naming Convention
/Markings short command
AMLG
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Amenity
_ArtiVentiShaft
_ArchProj
_Balcony
I.e. suppose there is a road widening in the Plot then the poly of road widening should be different for each amalgamation.
(For amalgamation, draw plot 1, plot 2, plot 3 on plot layer and amalgamated plot AmalPlot 1, on amalgamation layer overlapping plot 1)
Draw Amenity space as a closed polyline which is reserve for utilities, services and conveniences.
Draw ArtiVentilation shaft/duct area as a closed Polyline with Text.
Inside FSIArea on _ArtiVentiShaft
Layer. Only those shafts from which ventilation for habitable room is not taken should be drawn on this layer.
This layer is used to represent various Architectural Projections in your Plan. Draw a closed Polyline for Architectural Projections. And mark it using Mark->Projection from PreDCR menu, according to requirements. Canopy/porch will come in plot & other projections will come with floor plans.
Draw a balcony as a closed polyline which is a horizontal projection including parapet to serve as a sitting out place. Name of balcony must be inside and on _Balcony layer.
Mark -> Amenity ->
Surrendered (If it is surrendered)
Mark -> Projections ->
Cheju, porch, loft, canopy, etc.
If Balcony is Enclosed
Than
Mark -> Balcony ->
Enclosed Balcony
AMN
AVS
AP
BL
106
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Building
_Building Line
Building is used to group all floor plans of the same building. Draw a closed poly enclosing all the floor plans and section of the same building on _Building layer. Note:
As written above, dimension or area of this building poly has no meaning in AutoDCR. This is just a logical group of all floors of the same building. If the building plans of multiple Works or wings are same then building name shall be as given aside.
Draw a “_Building Line” as a closed poly line which area to be calculated for consumption of actual building line of that floor excluding cantilever projections.
Naming Convention will be provided by
Tool>Assign Name
A (Bldg.Name) inside
Bldg.Poly &
A-1 (Bldg.Name) inside
Pork Poly
BLD
BDL
107
_BLDGBLOCK(in layout) Description: - If you are submitting sub-division/amalgamation layout along with proposal for building permission also, then you should draw sub-div/amal. Layout on different drawing sheet and proposed building drawings on
_Carpet area different drawing sheet. In this case, tentative block of building should be drawn on '_BLDGBLOCK
(in layout)' just for referring the presence of building in sub-div. or amalgamation Plot
Draw carpet area as a closed polyline which is a net usable floor area within a building excluding that covered by the walls or any other areas specifically exempted from floor space index
Mark-> Carpet area-> normal (default),
Splitted, PAP, etc.
BLDBLK
CPT
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Chowk
_CommOuterWall
_Compound Wall
_ CRZ Boundary
_Dead Wall
_Door
_Electric line computation in these regulations.
Draw a chowk as a closed polyline which is an enclosed space permanently open to the sky within a building at any level. From chowk we take ventilation for habitual rooms
Draw a Commouterwall as a closed polyline which is the area covered by a building on all the floors. This
No need to give name on this layer. polyline mainly used for commercial use bldg.
Closed polyline of compound wall to be drawn on this layer overlapping plot.
CRZ boundary Boundary of coastal regulatory zone shall be drawn on
_CRZBoundary layer.
Draw open polyline overlapping with pwork on a side from where ventilation is not taken. And it should be drawn inside the plot.
1.5m high compound wall
Mention height of compound wall in its text.
Door is a closed Polyline Which is drawn on “_Door” layer. Also you can insert a particular size poly for
Door using Insert->Door from
PreDCR menu.
Electric line will be present in the layout plan and shall pass through plot entity as a non closed polyline.
Name electric line shall start with its voltage capacity and text insertion point shall lie on its polyline.
Insert-> Door
33 KV High Tension
Line
CWK
CMFS
CW
CRZ
DW
DR
L1
108
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Elevation
_ExStructure
_FloorInSection
_Floor
Description:- Elevation to be drawn in _Elevation layer only for printing purpose. No regulations will be checked by reading this layer. The drawing on this layer need not be drawn using poly lines.
Draw an Exstructure as a closed polyline which is a building or structure existing authorized before the commencement of these regulation. And mark it using
Mark -> Existing structure as 'To be demolished' or 'To be retained’.
Draw a Floor Inspection as a closed polyline which is the height of that floor (slab top to slab top) This poly only used for checking floor height.
For assigning the name of
FloorInSection then used
Mark-> Existing
Structure-> To be
Demolished OR
To be Retained
Assigned name option for PreDCR tool menu.
1. Name of each floor section will be same as of floor in plan.
2. For one typical floor plan multiple floor section will be there.
For e.g. for one typical floor plan for 1-3 floors there will three sections shall be drawn with name
"First Floor Plan", "Second Floor
Plan" and "Third Floor Plan" respectively.
Floor poly should be drawn as a closed Polyline with Text on same
Layer. This is just a logical Group of all floor Entities.
Floor Name: Floor Plan will be automatically link with Section
Naming Convention will be provided by
Tool>Assign
Name>Floor name
EL
ES
SECF
FLR
109
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Ground Level
_IndOuterWall
_IntDPRoad
_InternalRoad
_Liftwell
_Location plan by matching the Floor Name.
Hence all names to be given using
<Assign Name> function
The Ground level line should be drawn as an open polyline in the section poly.
Proposed Height will be considered from Ground Level Polyline
Draw a closed FSI Polyline, which is used as a Industrial Purpose.
Name of floor should be in given format:
TYPICAL-1,4 FLOOR
PLAN
TYPICAL-1-5 FLOOR
PLAN
TYPICAL-2&3 FLOOR
PLAN
Ground Floor Plan
No need to give name on this layer.
No need to give
Name on this layer.
Draw a DP Road as a closed poly line with Text. (e.g. any DProad passing from inside of the plot)(Note: Road width must be written at the starting of Text).
Draw each Internal Road as a closed Polyline with Centre Line
(Ltype-CentreLine) & single text inside it.
Draw a Liftwell as a closed polyline which is a mechanically guided car, platform or transport for persons and materials between two or more levels in a vertical or substantially vertical direction
Fire Liftwell means a special
Liftwell designed for the use of fire service personnel in the event of fire or other emergency.
Location plans if any to be drawn on this layer. This is only for
7.50 m wd. Internal
Road
Naming Convention will be provided by
Tool<Mark>Liftwell
If fire Liftwell are provided then use the marking of " Fire
Liftwell" option from
Mark -> Liftwell -> Fire
Liftwell.
GL
IFSI
R3
R2
LFT
LCP
110
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Margin line
_Main Plot
_Main Road
_Nala-WaterCourse
_Net Plot
_NotInPossession
_NDZ reference. No verifications are done by AutoDCR for this layer so not compulsory.
User need not do anything on this layer.
Margin Polylines will be created by PreDCR by using Tool
"Mark>Margins"
Draw a Main Plot poly as a closed polyline which is a parcel or piece of land enclosed by definite boundaries. A Main Plot will contain all Proposed Works
(buildings, wings), open space,
Internal Roads, Parking etc. The overall Main Plot Entity represent a
Plan, AutoDCR refers it as 'Layout
Plan'. The overall Main Plot Entity represent a Plan, AutoDCR refer it as "Layout Plan".
Draw Main Road as a closed Poly with Text, which should be abutting with the Plot closed Poly.
(Note: Road width must be written at the starting of Text)
Draw a closed Polyline on this layer and name of the poly should contain width of the Nala
No need to draw NETPLOT. This layer is not provided for PreDCR users.
Plot area which is not in possession or which is not in proposal to be drawn as a closed polyline on this layer.
Draw a closed poly line on _NDZ layer with containing text on same layer, if any part of plot boundary
24.00 m wd. Main
Road
No need to give name on this layer.
L3
PLT
R1
R4
NPLT
NIP
NDZ
111
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Parking
_Passage
_Pathway
_Phased Program
_PrintAdditionalDetail
_Podium
_PropWork containing NDZ area.
Draw a closed Polyline for Parking on “_Parking” Layer on stilt floor or podium floor. You need to Insert various sizes of parking from
PreDCR menu.
Draw a closed polyline on
“_Passage” Layer with its text.
(Note: If Premium for Passage is going to be Paid, Passage should be marked by using Tool "Mark "
Insert-> Parking-> Car-
L/ Car-s/ Scooter/
Transport Vehicle/
Visitor Parking OR
Ambulance, etc.
Mark > Passage > covered Passage.> Free from FSI or Taken in
FSI.
Mark > Passage > Open
Corridor
Mark > Passage > Fire
Escape Passage
Draw pathway as a closed polyline with text specifying its width.eg.1.5 m. wide pathway.
PK
PAS
R6
Draw phased program outlines covering floor plans or buildings/pworks on '_Phased
Program' layer inside plot or floor.
Enter name/number of Phased program -
E.g. Phase-1, phase-2, phase-3, phase4 etc.
apart from the layers specified by
PreDCR, any other information which user wants to display in final approval print shall be drawn on this layer
Draw a closed polyline on
“_Podium “to represent Podium. It should be shown in the layout and not in floor plans
PWork is a building profile and shall be drawn inside plot. Draw a closed polyline for Proposed Work
Tools > Assign Name >
Building and
PropWork.
POD
ADET
POD
PW
112
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_RailLine
_Ramp
_RecrationalGnd
_Refuge Area
_Refuge Chamber
_Refuge Chute
_ResiOuterWall
_Right-Of-Way on “_Prop Work” Layer.
Railway line shall be drawn in the layout plan as a Open Poly & Text which insertion point lies on the
Polyline. (Note: Railway Gauge must be written at a starting of
Text)
Draw a Ramp as a closed polyline with Centre line (L-type-Centre) &
Text inside it in Plan.
Draw Open space as closed polyline reserved as recreational space on this layer. With text on same layer.
You can mark it as paved or normal by using mark option
A closed polyline with Text around the refuge area should be drawn on same Layer.
Refuge area should be outside overlapped with FSI (ResiFSI,
CommFSI) poly.
Refuse chamber to be drawn in plan as a closed polyline with text on same layer which should be inside of floor
.
Refuse chute to be drawn in plan as a closed polyline with text on same layer which should be inside of floor.
Draw a ResiOuterWall as a closed polyline which is the area covered by a building on all the floors. This
FSI polyline only used for residential use bldg or floor.
Draw a closed polyline on “_Right-
Of-Way” to represent a Right Of way and text inside it representing its width. Layer should be inside or
_ Meter Gauge Railway
Line
10.0m long 1.5m high
Ramp
Mark -> Recreational
Ground -> Paved OR
Normal
No need to give name on this layer.
L2
RP
OPS
RFG
RMB
RFC
MFS
ROW
PreDCR help manual: Municipal Corporation Greater Mumbai
113
PREDCR SHORT-CUT COMMANDS
_ReservArea
_Road Widening
_Room
_Sewage line
_Section
_Service Duct
_Sanitation
_Site Plan intersecting with Plot poly.
If there in any Reservation Area in
Plot, it should be drawn as a closed
Polyline with Text inside same
Layer.
Road Acquisition/Road Widening area shall be drawn as a closed
Polyline with Text on same layer inside Plot Entity. Margin will be generated & checked from Road widening Poly by AutoDCR software.
A closed polyline for each room with its text inside should be drawn on this layer. Text should be given using <Assign Name> function
Drain/ Sewage line shall be drawn as an open polyline on this layer.
Assign Name > Room
Section poly should be drawn as a closed Polyline with Text on same
Layer. It is used to group all
Sectional detail like FloorInSection,
Plinth, Stair cabin, Tank etc.
(This is just a logical Group of
Sectional Entity).
(Note: Area or size of Floor doesn't have any meaning in AutoDCR)
Draw any sanitation entities on this layer. E.g. Urinals, Kitchen sink,
Ablution Tab, Drinking Water, etc.
The encapsulating poly around the
Site/Key Plan with the Text & Scale inside it.
PreDCR -> Insert ->
Sanitation Text
RSA
R5
RU
L5
SEC
SND
STP
114
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS
_Smoke Vent.
_Staircase
Smoke Vents are installed in buildings as an active fire protection measure. They are openings in the roof which are intended to vent the heat and smoke developed by a fire inside the building by the action of buoyancy. Such area to be drawn on “_Smoke Vent” layer as closed poly line.
Total Staircase area should be drawn as a closed polyline with text inside it.
This Main Stair Poly should contain
Intermediate Landing, Floor
Landing & Each Tread as an open polyline.
Intermediate & Floor Landing Poly can be Marked by PreDCR Tool
"Mark>Staircase>Int. or Floor
Landing"
(Note: If Premium for Staircase is going to be Paid, Staircase should be marked by using Tool
"Mark>Staircase>Free from FSI"
_SpecialUseOuterWall A closed poly represents a other than Residential, commercial or
Industrial use FSI or Floor FSI.
It will cover whole area which is considered in FSI Area per Floor.
_
Subdivision In Subdivision one plot is divided into more than one Subdivision.
All entities having subdivision as their container entity should be uniquely present in all Subdivisions of a Plot i.e. suppose there is a road widening in the Plot then the
SMV
Mark-> Stair Case->
Fire Escape Staircase
OR Fab/Spiral Stair
Staircase free from fsi paid/unpaid OR taken in fsi
Mark-> Staircase
Landing-> Flight Width
, Intermediate & Floor
Landing
STR
SUF
SBD
PreDCR help manual: Municipal Corporation Greater Mumbai
115
PREDCR SHORT-CUT COMMANDS
_SurrenderToCorpo
_SurrenderToMhada
_Substructure
_Tank
_Terrace
_TempStructure
_Tree
116 poly of road widening should be different for each Subdivision
(subdivided plot).
In case of accommodation reservation, the plot area or FSI to be surrendered to MCGM is to be drawn on This layer. With text inside it.
In case of accommodation reservation, the plot area or FSI to be surrendered to MCGM is to be drawn on this layer. With text inside it.
Substructures which are allowed in
Margins or Layout & Free from FSI should be drawn as a closed polyline with text inside it.
Name of the
Substructure can be assigned from
Mark>Substructure tool.
Assign Name>Tank Tank clear size should be drawn as a closed Polyline with Text on this
Layer in Floor Plan or Plot as well as Section with same Text.
(Note: It should be in proper
Naming convention which is
Provide by Predcr by using Tool.
Closed polylines around the terraces to be drawn on this layer.
If the terrace is used commonly by all tenements mark it as Common
Terrace else it will be treated as
Individual by default.
Area for temporary structures to be drawn as closed polyline with text on this layer.
Draw trees which are inside plot boundary in “_Tree” layer.
You can insert tree blocks from
Insert -> Tree
STC
STM
SSTR
TNK
TER
TMPS
TREE
PreDCR help manual: Municipal Corporation Greater Mumbai
PREDCR SHORT-CUT COMMANDS 117
_UpperSetback
PreDCR menu and Insert option
Draw a closed polyline in plan as well as in proposed work which having setbacks
USB
_Void
_Water Line
_Window
Specifications to be followed-
If the space is not Chowk then it can be void. All ducts (where ventilation is not taken) and double height rooms can be drawn in void layer.
Draw an open polyline on
“_WaterLine” to represent water lines.
Draw a closed polyline on
_Window” Layer to represent window. You can also use Insert tool to insert window poly for particular size.
Insert > window
VD
L4
WND
The drawing entities should be drawn on Automatic layers created by using PreDCR.
Plot layout, detailed floor plan and building section for all the floors should be there in one AutoCAD drawing file.
All building items like proposed plot, proposed work, proposed parking etc must be drawn using closed polyline.
(i.e. Every entity must be closed LWPOLYLINE except Railway Line , Drain line, Water Line, Electric
Line, Dead Wall and Ground level.)
Building Sub-Items must be exactly inside of outer closed polyline as per their place in architectural plan.
This means none of the edge or vertex of inside entity should be drawn outside its container entity.
For example Parking or Open Space poly must be exactly inside the main plot poly. Tools are provided in PreDCR to verify this check.
Every Building Sub-Items should be given a specific/unique name (Text or MText entity) on the same
PreDCR help manual: Municipal Corporation Greater Mumbai
layer & inside the entity poly. As far as possible, this name should be unique. If name not found then
AutoDCR will generate the name automatically. Naming Conventions should be followed properly. e.g. Each Room should be given the concerned name Using <Assign Name> function of PreDCR
Living, Kitchen, Bedroom. Etc. Floor Name: GROUND FLOOR; TYPICAL FLOOR 1,2 & 5-8; TERRACE
FLOOR. Floor Items: Room Names should be given properly without using abbreviations so the software can identify perfect entity. This can be done by Assign name facility provided by the software.
User shall use only following kind of entities for Building Items: -
LWPOLYLINE / TEXT / MTEXT
If in a plan two proposed work are mirrored in that case user should provide two separate building plans for each proposed work.
PreDCR help manual: Municipal Corporation Greater Mumbai
118
Sample cases
Sample cases
Residential Bldg (Row house)
Residential bldg. (Single Detached with two buildings)
PreDCR help manual: Municipal Corporation Greater Mumbai
119
Sample cases
Commercial building
Industrial Building
PreDCR help manual: Municipal Corporation Greater Mumbai
120
Sample cases
Special building (School bldg)
PreDCR help manual: Municipal Corporation Greater Mumbai
121
Meaning of various PreDCR Messages
Meaning of various PreDCR Messages
“Entity contain more than one text"
It means Entity on this layer contain more than one text. So remove the extra text. PreDCR need only one text for one entity.
" Entity not contain any text"
It means this entity not having any name/text, so give the name to this entity on this layer
"Polyline is not in a proper format"
It means Highlighted polyline not drawn properly. So redraw that polyline & check the properties of that polyline.
"Entity is not closed"
It means the highlighted entities not a closed polyline so close it by using 'pedit' command.
"Entity is supposed to inside one of the following entities"
It means this highlighted entity should be present inside the one of the entities present in the given list“
"Entity is supposed to touching one of the following entities"
It means this highlighted entity is supposed to be touched one of the entities in given list
"Entity should be outside overlapped with following entities“
It means the highlighted entity should be outside overlapped with one of the th entities in the given list.
“Entity must contain one of following entities“
It means any one layer should be present inside in this entity which is listed.
Following subentities are not found inside:
Direction Ref Point on layer _Floor,
PreDCR help manual: Municipal Corporation Greater Mumbai
122
Meaning of various PreDCR Messages 123
Type: BLOCK, Color: ByLayer Status:
Common Point on layer _ResiFSI,
Type: BLOCK, Color: ByLayer Status:
It means insert the direction reference circles in side of that entities.
"The corresponding Building not found with same name"
It means that proposed work not having building with same name. So assigned that building with having same name of proposed work.
"Mark Substructures using PreDCR mark Substructure tool"
It means mark the substructure by using mark -> Substructure menu. Do not type substructure name manually.
"The Liftwell machine room not found in building"
It means Liftwell machine room having name not same in Plan & in section.
"The Liftwell poly is not suppose to be touch Liftwell machine room"
It means Liftwell machine room should be touch to Liftwell poly in the section.
‘Invalid objects, Please Try again"
It means If user marking balcony as a enclosed but selecting layer of terrace then this message are getting. If selected entity is incorrect then invalid objects message are showing. So select correct layer for particular of that layer marking only
"Section not found"
It means If all the floor plans are drawn but one of them in section floor are missing to converting floor in section layer then this message are getting. So draw all the floor plans with floor in sections.
"The corresponding entities not found in section"
It means that listed entities not present in the section so show that entities in the section.
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions)
"The corresponding entities not found in floor"
It means that listed entities not present in the floor so show that entities in the floor plan.
“Two Tanks should not have same Name”
It means that two tanks not having a same name. So assigned two tanks by using Assigned name
PreDCR menu.
F.A.Q (Frequently Ask questions)
Hardware lock not found.
1) If user having Parallel port lock then they have to follow following steps.
Open My Computer -> C: Program files -> SEPL -> PreDCR -> Hlock
1.1. Open this Hlock folder & drvinstall -> click on install button & then click on Exit button.
1.2. Now open Checklock & click on check lock window. Check the return code & Description. If return code is 0 then u will get the Description is “ lock found” otherwise fixed the lock properly.& do the step 1.1again & check the lock.
If user having serial port lock (its look like pen drive)
2.1 Plug the Sentry USB Lock to any of the available USB Port on the PC.
2.2 The Found NEW HARDWARE WIZARD will be displayed. Click NEXT to continue.
124
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions) 125
2.3. Next window coming on screen will be of Choose your search and installation options in this window select the option Include this location in the Search.
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions) 126
2.4) Browse the correct path for the sentry USB driver (SentryUsb.sys) as e.g. C:\Program
files\SEPL\PreDCR \ HLock and click Next option .
2.5)
The next window you will get regarding waiting still installation after the installation is over the
Next button will be highlighted click it.
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions)
2.6) Sentry USB device Drivers will be installed at this point Click Finish to complete the installation.
127
2.7) Sentry USB Lock is now installed and ready to use. Sentry USB will be displayed in the Device
Manager as below.
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions)
Internal error or Fatal error while verify the drawing
Copy that file and paste it into the new drg file & then verify.
If Drawing is Automatically closed / crashed while marking any entity or verify complete drg.
Copy that file and paste it into the new drg file & then verify.
128
While performing verification if following massage comes, then follow the steps
Check each layer separately until you found problematic layer
PreDCR help manual: Municipal Corporation Greater Mumbai
F.A.Q (Frequently Ask questions)
PreDCR Settings for Windows Vista Operating System
Install PreDCR from CD
After Installation, “Right Click” on Desktop Shortcut of Predcr OR AutoDCR I con & click on
“Properties”
Select “Compatibility” option from “PreDCR” OR “AutoDCR Properties” dialog.
In that, Select “Run this program in compatibility mode for:” (from Compatibility mode option) & select Windows XP/Windows XP (Service Pack 3) option from List.
Select “Run this program as an administrator” check box.
129
Click on “Apply” button & then click “OK”
This is only one time changes.
Now PreDCR OR AutoDCR will run fine in Windows Vista
PreDCR help manual: Municipal Corporation Greater Mumbai
This is the last page of the document
PreDCR help manual: Municipal Corporation Greater Mumbai
130
Télécharger
Lien public mis à jour
Le lien public vers votre chat a été mis à jour. Vous pouvez afficher et gérer vos liens de chat après inscription ici.
Lien public du document
Publicité
