Инструкция EAN


Add to my manuals
74 Pages

advertisement

Инструкция EAN | Manualzz

EAN Plus Series

IP Box Camera

User’s Manual

** Lens not included.

Copyright © EverFocus Electronics Corp,

Release Date: July, 2012

Copyright

 2012 EverFocus Electronics Corp.

All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the EverFocus Electronics Corporation.

EverFocus

12F, No.79, Sec. 1, Shin-Tai Wu Road,

Hsi-Chih, Taipei, Taiwan

TEL: +886 2 2698 2334

FAX: +886 2 2698 2380 www.everfocus.com.tw

July, 2012

Regulatory Notices

About this document

All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.

FCC Notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or parties authorized by EverFocus could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

EverFocus Electronics Corp.

12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,

Taipei Hsien, Taiwan, R.O.C.

EAN Plus-series cameras comply with CE and FCC.

Safety Notice

These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and the receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture.

Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.

Handle the appliance with care. Do not strike or shake, as this may damage the appliance.

Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.

Do not operate the appliance beyond its specified temperature, humidity or power source ratings.

Do not use the appliance in an extreme environment where high temperature or high humidity exists.

Use the appliance at a temperature between 0°C and 50°C / 32°F and 122°F and a humidity level between 0% and 80% non-condensing. The input power source for this appliance is 12VDC & PoE.

Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard.

Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid electrostatic discharge.

Installation should be performed by qualified service personnel only in accordance with the

National Electrical Code or applicable local codes. ii

Terms and Trademark

Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered trademarks of the respective holders. Other product names appearing in this User's Guide may be trademarks or registered trademarks of their respective holders. Java™ and all Java-related logos and trademarks are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.

Support

If the unit ever needs to be repaired or serviced, the customer should contact the nearest EverFocus

Electronics Corp. Service Center for return authorization and shipping instructions. iii

CONTENTS

1. Introduction

................................................................................................................. 1

2. Overview

..................................................................................................................... 2

3. Features

....................................................................................................................... 3

4. Installation

................................................................................................................... 4

4.1 Packing List ....................................................................................................................................... 4

4.2 I/O Terminal Block ........................................................................................................................... 5

4.3 Lens Installation and Adjustment .................................................................................................... 5

4.4 Top / Bottom-Mount ....................................................................................................................... 6

4.5 Basic Connection .............................................................................................................................. 7

5. Accessing the User Interface ........................................................................................ 8

5.1

Assigning an IP Address

......................................................................................................................................... 8

5.2

Connecting the Camera to the Network

......................................................................................................... 10

5.3

Live View Window

................................................................................................................................................. 12

6. Playback ..................................................................................................................... 15

6.1

Remote Playback Using Playback Page

........................................................................................................... 15

6.2

Setting up the Playback Function

...................................................................................................................... 17

6.2.1 Preparing the Micro SD card

................................................................................................................... 17

6.2.2 Testing the Playback Function

................................................................................................................ 17

6.3

Playing Back Using ARV Viewer

......................................................................................................................... 19

7 Settings ...................................................................................................................... 20

7.1

System Info

.............................................................................................................................................................. 20

7.1.1 Information .......................................................................................................................... 20

7.1.2 Log ........................................................................................................................................ 21

7.2

User Config

.............................................................................................................................................................. 22

7.2.1 Live View Config ................................................................................................................... 22

7.2.2 Recording / Snapshot ........................................................................................................... 23

7.2.3 Language .............................................................................................................................. 24

7.3

Network

.................................................................................................................................................................... 25

7.3.1 Network ................................................................................................................................ 25

iv

7.3.2 DDNS ..................................................................................................................................... 27

7.3.3 SMTP / FTP ........................................................................................................................... 29

7.3.4 HTTPS .................................................................................................................................... 31

7.3.5 SNMP .................................................................................................................................... 34

7.3.6 Network Alarm ..................................................................................................................... 34

7.4 Video .............................................................................................................................................. 35

7.4.1 Multi Streaming .................................................................................................................... 35

7.4.2 Camera ................................................................................................................................. 37

7.4.3 Advanced .............................................................................................................................. 39

7.4.4 ROI (Region of Interest) ........................................................................................................ 46

7.4.5 Privacy Mask ......................................................................................................................... 47

7.5 Audio .............................................................................................................................................. 49

7.6 User ................................................................................................................................................ 50

7.6.1 User Information .................................................................................................................. 50

7.6.2 IP Address Filter .................................................................................................................... 52

7.7 Event .............................................................................................................................................. 53

7.7.1 Event Settings

.............................................................................................................................................. 53

7.7.2 Motion Detection

....................................................................................................................................... 56

7.7.3 Tamper Detection

...................................................................................................................................... 57

7.7.4 Alarm I/O

...................................................................................................................................................... 57

7.7.5 Schedule

........................................................................................................................................................ 58

7.8

S

YSTEM

........................................................................................................................................................................ 59

7.8.1 Date/Time

..................................................................................................................................................... 59

7.8.2 Daylight Saving

............................................................................................................................................ 60

7.8.3 SD Card

.......................................................................................................................................................... 60

7.8.4 Maintenance

................................................................................................................................................ 61

8. Upgrading Firmware Using IP Utility ........................................................................... 63

9. Specifications ............................................................................................................. 65

v

EAN Plus Series

1.

Introduction

The EAN Plus series is a box-type IP camera delivering image quality of up to 5-megapixel. The EAN Plus series features the Wide Dynamic Range (WDR) function, which can provide clear images even under back light circumstances where intensity of illumination can vary excessively. A built-in micro SD card slot and Power over Ethernet (IEEE802.3af) features are also provided. You can power the camera over the network or by connecting the camera to a 12V DC power supply. The camera also features H.264 /

MJPEG multi-stream output for simultaneous live monitoring and high-resolution recording. Since the

EAN Plus series conforms to ONVIF / PSIA for compatibility with other network video devices, it interoperates with a wide variety of hardware and software systems. The EAN Plus series is designed for simple installation and supports all types of indoor mounting applications.

The EAN Plus Series Models

Model Name

EAN3120 Plus

EAN3220 Plus

EAN3300 Plus

EAN3520 Plus

System Requirements

Megapixel

1.3 MP

2 MP

3 MP

5 MP

WDR

Yes

Yes

No

Yes

Before installing, please check that your computer meets the following system requirements.

Operating System

Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)

CPU

RAM

Intel Core2 Duo 2 GHz or higher

1 GB or more

Additional HD space depends on required local storage of video files,

100 Mbps network card.

Screen Resolution

1024 x 768 pixels or higher, 32-bit pixel color resolution

Software

DirectX 9.0c

Microsoft Internet Explorer 7 or higher

1

2. Overview   

EAN Plus Series 

 

 

 

 

 

 

 

 

 

 

 

 

No.  Item Name 

Memory Card Slot 

Power LED 

DC 12V Port 

Ethernet / PoE 

Reset Button 

I/O Terminal Block 

Video Out 

Audio In 

Audio Out 

10 

Light Sensor 

Descriptions 

Insert a micro SD / SDHC card to store recording data. 

Indicates the power is supplied. 

Connects to power. 

Connects to a 10/100 Ethernet or PoE. 

Resets all configurations to factory default. 

Connects I/O devices. 

Connects to a portable monitor for setting the focus and angle of  the camera during initial installation.

Connects to a microphone for audio input. 

Connects to a speaker for audio output. 

Detects lights. 

11 

Auto Iris Lens Connector  Plug the Iris control cable to the connector. 

 

2

EAN Plus Series

3.

Features

1/3” Panasonic CMOS sensor (for EAN3120 Plus / 3220 Plus)

1/2.8” Sony CMOS sensor (for EAN3300 Plus)

1/2.5" Aptina CMOS sensor (for EAN3520 Plus)

Triple streams (stream 1 / 2 / 3 from H.264 or MJPEG)

Up to 15 fps at 2560 × 1920 (only for EAN3520 Plus)

Auto Iris control

Built-in micro SD / SDHC card slot

Removable IR-cut filter for Day / Night function

One alarm input and output

Two-way audio

TV-out

Wide Dynamic Range (for EAN3120 Plus / 3220 Plus / 3520 Plus)

2D / 3D Dynamic Noise Reduction (DNR)

Motion detection

Privacy mask

DC 12V / PoE

3

EAN Plus Series

4.

Installation

4.1

Packing List

• EAN Plus Series Camera (lens not included) x 1

• Software CD x 1

• Quick Installation Guide x 1

• Tool Packet x 1 (contains the following items)

-

C-mount lens adapter

-

¼-20 UNC thread mounting bracket and 2 screws

-

Hexagon wrench

-

Power pigtail cable

Note: Contact the shipper if any items appear to have been damaged in the shipping process. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service

Branch. Please also keep the shipping carton for possible future use.

4

EAN Plus Series 

 

 

4.2 I/O Terminal Block 

The I/O terminal block, located on the rear panel of the camera, can be used to develop application  for alarm input and output. 

 

Pin Assignment 

No.  Function 

1  Alarm COM 

2  Alarm Output 

No. Function 

3  Alarm Input 

4  Digital GND 

4.3 Lens Installation and Adjustment 

You can install either a CS‐mount or a C‐mount lens into the camera. It is recommended to use a lens  with aperture ratio of F/1.4 or smaller. Please refer to the following reference steps. 

 

 

 

 

CS‐Mount Lens:   

1. Remove the cover cap from the camera body. 

2. Install the lens into the camera body.   

3. Adjust the lens using the Focus / Zoom Screws. 

 

If you are using a DC Auto Iris lens

1. Remove the cover cap from the camera body. 

2. Install the lens into the camera body. 

3. Connect the DC cable to the DC Auto Iris Lens Connector. 

5

 

 

             

 

 

 

 

EAN Plus Series 

4. When making final focus adjustment, place the ND filter in front of the lens to force the lens iris      to open, and then adjust the lens using the Focus / Zoom Screws.   

Note: To use the ND filter, remove the protective sheets from both sides of an ND filter. 

 

 

5. Lock the Focus Screw and then remove the ND filter. 

C‐Mount Lens:   

1. Remove the cover cap from the camera body. 

2. Install the lens into the camera body using the supplied C‐mount lens adapter.   

 

 

3. Adjust the lens using the Focus / Zoom Screws. 

 

Note: Installing a C‐mount lens without the C‐mount lens adapter may damage the camera sensor. 

4.4 Top / Bottom‐Mount 

You can use the supplied mounting bracket and screw it on the top of the camera body to suspend  the camera, or on the bottom of the camera body to support the camera. 

 

6

EAN Plus Series 

 

 

4.5 Basic Connection 

 

 

 

1. Use a standard network cable to connect the camera to the network. 

2. Connect the camera to power using one of the following methods: 

 Plugging the supplied power pigtail cable to the DC 12V port. 

 Using the PoE function and the power will be provided over the network cable. 

3. Optionally connect the camera to a speaker or microphone. 

4. Optionally connect the camera to a monitor using a BNC cable.   

5. Optionally connect the camera to the input / output devices. 

 

 

 

 

 

 

 

 

 

 

 

After powering the camera, the power LED will be lit in red and you can access the live view and  adjust the image clarity. 

7

EAN Plus Series

5.

Accessing the User Interface

This section explains how to access the Web interface of the camera for configuration

5.1

Assigning an IP Address

You have to assign an IP address for your camera to be accessible. To assign an IP address to the camera, use the IP Utility (IPU) software included in the software CD. Please connect the IP camera in the same LAN of your computer.

1.

Install and then start the IPU program

. The following dialog box appears.

2.

Click Find Devices to search the cameras connected in the LAN. The default network values of the

cameras will be displayed. By default, the network protocol of the camera is DHCP.

3.

To configure the network settings, select a camera and then click Login/Multi Login to log in.

8

EAN Plus Series

4.

Type the user ID and password. Click OK.

Note:

1.

The default user ID is user1 and the default password is 11111111.

2.

If you select more than one camera that has the same user ID / password, you will be able to log in several cameras at once.

5.

To change the IP address, double-click the IP Address of the camera. Type a new IP address and

then click Set IP Address to save the settings.

You can also change the other settings by double-clicking the values. After configuring the values, click Save Configuration.

Note: Most networks uses DHCP to assign IP address, if you are unsure of your network settings, please consult your network administrators for configuration details.

6.

To access the camera, highlight the camera and click Connect to Selected IP. The Internet

Explorer window pops up.

7.

Type the user ID and password to log in. The Live View window of the camera appears.

Note: You might be required to download ActiveX, which is required to view the camera feed.

If asked, click "Yes".

9

EAN Plus Series

5.2

Connecting the Camera to the Network

There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct

High-Speed Connection and One-to-One Connection.

Router or LAN connection

This is the most common connection in which the IP camera is connected to a router and allows multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you can remotely access the cameras from outside of the LAN via the Internet. To remotely access the

Web interface of the IP camera, please refer to 7.3.2 DDNS. To set up port forwarding, please consult the manual of the router.

Straight-through LAN patch cable

Right: Pinout of a straight-through cable.

10

 

EAN Plus Series 

Direct High‐Speed Connection 

In a Direct High‐Speed Connection, the camera connects directly to a modem without the need for a  router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service 

Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”,  where xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may  require that you use DDNS for a reliable connection. Please refer to 7.3.2 DDNS.   

 

 

 

 

 

 

 

 

One‐to‐One Connection (Directly from PC to IP Camera) 

You can connect directly without using a switch, router or modem. However, only the PC connected  to the camera will be able to view the IP camera. You will also have to manually assign a compatible IP  address to both the computer and the IP camera. Unless the PC has another network connection, the 

IP camera will be the only network device visible to the PC. See the diagram below: 

 

 

 

 

               

  Pinout of straight patch cable                  

 

Right: Pinout of a crossed‐over cable. 

11

EAN Plus Series

5.3

Live View Window

1.

Press the

button to display the "Live View" window. Double-click on the image to show a full-screen display, double-click again or press ESC to return to the normal display.

If you experience video feed lag time (if connected via Internet), you can reduce the resolution or limit the number of streams. See 7.4.1 Multi Streaming.

2.

Press the button to play the recorded data directly from the on-camera Micro

SD / SDHC card (for this function to become active, you have to insert a Micro SD / SDHC card in the

Micro SD / SDHC card slot on the rear panel of the camera. See 7.8.3 SD Card.

3.

Press the

button to enter the Settings page. On the Settings page, there are

8 submenu sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event], and

[System]. Click on the section buttons to open their configuration fields. See the Settings section below for more information.

12

EAN Plus Series

4.

Press the

5.

Video Stream

button to exit the system and close this browser page.

Select the Video Stream (Stream 1, Stream 2 or Stream 3) that will be displayed in the video box on the right. Stream 2 and Stream 3 are only selectable if you have enabled the stream. The default setting is Stream 1 only. See 7.4.1 Multi Streaming.

6.

View Size

Use this to select the appropriate view size and shape of the video box on the right. A smaller size might increase transmission speed and video quality.

7.

Digital Zoom

Click the Zoom In / Zoom Out buttons or roll the mouse wheel to zoom in / out the camera live view up to 10x. Clicking on a magnified image will re-center the image around that point.

8.

One Push

This function is only available for EAN3120 Plus / 3220 Plus. The One Push button can be displayed on the live view window by enabling the Show One Push Buttons function on the User Config < Live

View Config Setting page (see 7.2.1 Live View Config). To enable the button (turned from faded to clear), on the Video < Advanced Setting page, select One Push from the White Balance Settings

Mode drop-down list, and click the Apply button. Once this is done, pressing the One Push button on the Live View Window will instruct the camera to adjust the white balance settings, and these settings will be active until the button is pushed again. This is like a “semi-automatic” way to adjust white balance to suit the user, if the Auto or Manual mode does not give the result the user wants.

9.

Record

The Record button is used to record the current video stream. Click the Record button to start / stop recording. This icon is only for one-minute video recording. To record long-period recordings, please set a recording schedule (See 7.7.5 Schedule). The location on your computer, where the image files will be saved to, and file size can be specified in the submenu (see 7.2 User Config).

10.

Snapshot

Click the Snapshot button to save a snapshot of the video image currently being displayed. The location on your computer where the snapshot data will be saved can be specified in “Settings >

User Config > Recording/Snapshot” (see 7.2 User Config).

13

EAN Plus Series

11.

Play Audio / Transmit Audio

Click the “Play Audio” (speaker) and “Transmit Audio” (microphone) buttons to switch the sound on/off for the speaker and microphone, respectively (if such external devices have been connected to the camera directly or via the network).

12.

Manual Control

Trigger Event

Press the “Trigger Event” button to trigger an event directly from the Live page. If you have configured an event (in the Event submenu) that will trigger a reaction (like a recording) when a

Manual Trigger event occurs, clicking this button will trigger that reaction. You can select what that reaction will be. You can, for instance, set the camera to record the audio/video feed to the Micro

SD card on board the camera. You can then click on the Playback button to open the Playback page and search for and play all such recordings that had been stored on the card. Such event actions will be effective once they have been configured in the “Event” menu (see 7.7 Event).

Reset Alarm

Press the “Reset Alarm” button to reset the alarm output remotely.

13.

Status Display (info lines that can be placed above video box or at bottom of page)

This shows the name of the camera that is currently active or being configured, current date/time and current frame rate. You can activate these info displays in the Settings > User Config page (see

7.2 User Config).

14.

Event Signal Icons (above video screen)

When an alarm or motion event is triggered, a signal icon will appear at the top right of the Live

View window to alert the user.

Alarm event icon : When an alarm is triggered, this icon appears.

Motion detection icons : The colors of these motion event icons correspond to the colors of the motion trigger areas you have configured in the Motion Detection submenu (see 7.7.2

Motion Detection).

Recording icon : When the camera is recording to a PC-based folder, this icon appears.

14

EAN Plus Series

6.

Playback

You can remotely play back the recordings stored in the on-camera micro SD card on the Web interface, or play back the recordings stored in the computer using the ARV Viewer included in the software CD.

Playback is designed as a quick way to check recent recordings that were triggered by Events that were configured to “Record to SD Card” in the Settings > Event > Event Settings page (see 7.7.1 Event

Settings).

Note: Note that the Playback page is only accessible once the on-camera SD card is inserted and active.

6.1

Remote Playback Using Playback Page

On the Live View Window, click the Playback button to open the Playback page.

15

EAN Plus Series

Search by File: Click the Search button to search for all recording files on the on-camera SD card.

Search results will be displayed in the Filename area.

Search by Time: Click the calendar icon and select the date and time from which you want to search until the present moment. Click search to get your search results, which will be displayed in the

Filename area.

Search by event: Click the type of Event recordings you want to search for (Alarm, Motion, Manual

Trigger) and then click the calendar icons to select the Start Time date/time and the End Time date/time of your search. Click Search to get your search results, which will be displayed in the

Filename area.

Multiple Files: Check this box if you want the video player to play all the files in the selected folder.

The files will be displayed in the Filename area.

Loop Again: Check this box if you want the video player to play the selected file over and over again.

Play: Once you have opened the file’s folder and have clicked on the file to highlight it, its details will be displayed in the File Information area. You can now click Play to play that specific file.

Pause: Click this button to pause the playback.

Stop: Click this button to stop the playback.

Recording List

Filename: This area will display a list of search results (recording files and folders). Folders (named with the recorded date) will be displayed first. Click on the folder and click on each subfolder until the recording files (.arv) in that folder is listed.

File Information: Click a file on the Filename list, the selected file information will be listed.

Copy: Click this button to copy the selected file to the computer-based folder of your choice. A browsing box will open so that you can search for the folder of your choice. You can use the ARV

Viewer to play back the recordings recorded in your computer. For details on ARV Viewer, see 6.3

Playing Back Using ARV Viewer.

Lock: Click this button to lock the selected file. This will protect that file from being overwritten during any overwrite procedure. The file will thus be saved on the micro SD card indefinitely. However, the file will still be deleted if the micro SD card is ever formatted.

Remove: Click this button to delete the selected file.

16

EAN Plus Series 

6.2 Setting up the Playback Function 

Note that the Playback function will not be active until the user has inserted a micro SD card in the  camera’s micro SD card slot. The card may also have to be formatted in the Settings submenu. 

 

 

 

6.2.1 Preparing the Micro SD Card 

Once you insert a functional micro SD card into the slot, the Playback button on the Live page should 

become active within seconds (see section 6.2.2 below – the grey letters should turn white). IF NOT, 

  do the following:   

1. From the Live page, click Settings > System > SD Card. If no card has been inserted yet, the 

      Remove button should be faded, indicating that no card is being detected. (If a card is 

      inserted, and the Remove button is still faded, pull the card out and re‐insert it.) 

2. Slide the card into the slot until it clicks into position. 

3. The Remove button should become active within a few seconds, indicating the card is active. 

 

4. If the Remove button stays faded, click the Format button to format the card. NOTE: All data 

      on the disk will be deleted if the Format button is clicked.   

6.2.2 Testing the Playback Function 

1. Once the SD card is detected by the system, the button          (inactive) 

      will turn to    (active).   

2. To test the Playback function (this is not required), set up a “Manual Trigger” Recording 

      Event by clicking Settings > Event > Event Settings.   

3. Click the “Add” button on the middle right side of the page to open an “Add Event” box. 

4. Give the event a name, like “Test 1”. 

17

EAN Plus Series

5.

In the “Event Triggered by” field, click on Manual Trigger.

6.

Below this, check “Enable This Event”, “Enable Post-trigger Buffer”, and “Record to SD Card”.

7.

To save your settings, click OK, or close the box by clicking on the red x icon at top right of the box (in which case you will be asked if you want to save the data, to which you should reply OK).

The box will close and the new event will be listed in the list area of the Event Settings page.

8.

Look at the “Post-trigger Buffer” at the bottom to make sure the buffer time is set to 10 seconds.

9.

Click “Apply” to make sure all settings are saved.

10.

Click the Live button to go back to the Live page.

11.

Get ready to click the Trigger Event button at the bottom of the page. Before you do, see if you can find something in the view screen that will give you a visual time marker. For instance, if you can get your hand in front of the camera’s lens, get ready to count down on your fingers.

12.

Click the Trigger Event button and slowly count down on your fingers in front of the lens (if you are able to do so – if not, try to find visual cues on the view screen that will help you to mark the moment you pushed the trigger). The recording period will be as long as the buffer time you selected – the default period is 10 seconds.

13.

Click the Playback button to open the Playback page.

14.

There are different ways to search for recording files on the camera’s Micro SD card (i.e. the

Playback memory). For a recent recording like your test event, simply click the “Search” button under the “Search by File” header.

15.

If the SD card is active and formatted correctly, the recording folder’s name (the recording day’s date) will appear in the Filename box at the bottom. Click on this folder to open it. If there are sub-folders, click on the bottom one (the most recent would be at the bottom) until you can click on a file that cannot open to another sub-level and shows data in the File Information box to the right. This would be the file of the most recent recording event.

16.

To play this file, click the Play button below the video box. The test footage you have recorded should start playing. Play time should be 10 seconds if you left the Post-trigger Buffer as 10 seconds.

18

EAN Plus Series 

6.3 Playing Back Using ARV Viewer 

You can play back the recordings stored in the computer using the ARV Viewer 

  included in the  software CD. To store the recordings in the computer, please refer to Recording List > Copy in 6.1 

Remote Playback using Playback Page

 

 

 

 

No.  Item Name 

1  Snapshot 

2  Load File 

3  Convert ARV to AVI 

Descriptions 

Click to take and save a snapshot. 

Click to load the recordings for playing back. 

Convert the recording from ARV format to AVI format. 

Playback Time  Display the playback time. 

5  Total Time of Recording 

Display the total time of the recording. 

6  Stop 

Click to stop playing the recording. 

7  Step Reverse 

8  Play 

9  Pause 

Click to display the previous frame. 

Click to play back the recording. 

Click to pause the recording. 

10  Step Forward 

Click to display the next frame. 

19

EAN Plus Series

7

Settings

Click the Settings button on the Live View Window to enter the settings submenu. There are nine buttons on the left-side of the submenu: Live, System Info, User Config, Network, Video, Audio, User, Event and

System. Click the Live button can go back to the Live View Window.

7.1

System Info

The System Information and System Log can be checked on this page. Click the top tab of the one you want to see.

7.1.1

Information

Click the Information tab, the following dialog box appears. These values cannot be changed on this page, and are for reference only.

20

EAN Plus Series

7.1.2

Log

Click the Log tab, the following dialog box appears. The sequence number, date, time and event messages of the log event will be displayed in the System Log field. The log will display the last 256 log events. Click the Export button to export the system log event list into a “.txt” file and select the location where the exported log file will be saved to.

21

EAN Plus Series

7.2

User Config

Each user can set a different configuration for his/her Live page here. These settings will be applied to the logged-in user’s Live page every time he/she logs in.

7.2.1

Live View Config

Video/Audio Connection Protocol Setting】If needed, select the protocol that applies to your connection setup. Click Apply to apply the changes or Reset to reset without saving the changes.

Text Settings】Check the box of each option (Machine name, Date/Time, Frame Rate) to display this info on the Live View Page.

Foreground Color: Slide the Red, Green and Blue bars to create your preferred text color for the info text line.

Position: Select the position where the text will be displayed. Choose from Upper Left / Lower

Right / Lower Left.

Click Apply to apply the changes or Reset to reset without saving the changes.

Date/Time Format Used in Text】Click the dropdown menu to select date/time format from the listed options. Click on the desired hour format. Click Apply to apply the setting changes or Reset to reset without saving the change.

Live View Layout Settings Check the “Show One Push Buttons” boxes if you want to show these buttons on the Live View Page. Uncheck these boxes to hide these buttons. This function is only available for EAN3120 Plus / 3220 Plus.

22

EAN Plus Series

7.2.2

Recording / Snapshot

This configures where your Record Button and Snapshot Button ( ) files will be saved if you click one of these buttons. Selectable folders will be on the computer only, not on the on-camera SD card.

Recording / Snapshot Export Settings

Enable Event Recording to PC: Checking this box will let the system save Record/Snapshot Button recordings to the folder configured below on the user’s PC.

Export Folder: Select the Export folder for the action above by clicking on the browse (…) button, and then select the desired folder.

File size:

The user can limit the size of each recorded file here (in minutes).

When a single recording file exceeds the time you set, the system will create a new file to save that data to.

Overwrite: Select “ON” for overwriting recording/snapshot file when the disk storage capacity is full. The user can set the storage capacity limitation in the in-sentence field in the gray box below the Overwrite setting: “If the remaining hard disk capacity is less than ____ MB (50~2000), system will stop recording or start overwriting. “

Click Apply to apply the setting changes or Reset to reset without saving the changes.

23

EAN Plus Series

7.2.3

Language

Select the language to be displayed on the Web interface of the IP camera. The default language is

English.

To add a new language not listed in the current Language list, click the Browse button to locate the new language file (.evb) on your computer and then click the Upload button. Updated language files might be available on the manufacturer’s website. Contact your vendor if required.

Click Apply to apply any changes or Reset to reset without saving the changes.

Note: Uploading a new language file will cause the system to reboot automatically. Please create a new network connection to the IP camera when the reboot is complete.

24

EAN Plus Series

7.3

Network

This page covers network-related settings, including Network, DDNS, SMTP/FTP, HTTPS, SNMP, and

Network Alarm.

7.3.1

Network

The following information is required to configure the network settings. Contact your network administrator or your internet service provider to get the info.

IP Settings

IP Type: Refer to the network administrator for these settings of the server. Default: DHCP

DHCP: This setting lets the system use an automatically assigned (dynamic) IP address. This address can change under certain circumstances. For instance, when the camera’s network switch/hub has to be rebooted. Do not assign to the DHCP server the same IP addresses used for the other network cameras and PCs with unique IP addresses.

Static IP: The user can manually set the Static IP address. This type of address is stable and cannot change, but the user has to make sure there are no address conflicts with other network-connected devices.

PPPoE: This is a DSL-connection application. The ISP will ask the user to input a username and password. Contact your ISP for these details.

25

EAN Plus Series

Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to detect the device.

IP address: When DHCP is not used, the user needs to manually enter the IP address of the camera. Do not enter an IP address that is already used for your computer or other network cameras.

Subnet Mask: This field is used to set the netmask for your network, so that the IP camera will be recognized within the network. Example: 255.255.255.0. When DHCP is selected, the DHCP server will assign this value automatically.

Gateway: This field is used to set the gateway for your network so that the IP camera will be recognized within the network. When DHCP is selected, the DHCP server will assign this value automatically.

Primary DNS: Enter the IP address of the DNS server if this is provided by an ISP.

Secondary DNS: If your ISP provided you with a secondary DNS address, please enter it here.

Username: Enter the account’s username (used only for PPPoE).

Password: Used only for PPPoE.

IPv6: Enter the IPv6 details in this area, if this applies to your system.

Click Apply to apply the setting changes or Reset to reset without saving the change.

Port Settings】Enter the HTTP, HTTPS and RTSP port numbers and click Apply to save.

Multicast Settings】Enable if required, fill in the setting options and click Apply to save.

26

EAN Plus Series

7.3.2

DDNS

DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP address of a network device. You can set up the DDNS service for remote access to the IP camera.

DDNS assigns a domain name (URL) to the IP camera, so that the user does not need to go through the trouble of checking if the IP address assigned by DHCP Server has changed. Once the IP is changed, the IP camera will automatically update the information to the DDNS to ensure it is always available for remote access.

Before enabling the following DDNS function, user should have applied for a host name from the

DDS service provider’s website. We support these four DDNS server providers: www.everfocusddns.com, www.sitelutions.com, www.dyndns.com, and www.no-ip.com

Note: We highly recommend that you use xxxx.everfocusddns.com for the simplicity of setting up your IP cameras.

DDNS Settings

Enable: Check this box to enable the DDNS function.

Service ISP: You can either apply for a host name from EverFocus or other DDNS server providers.

If you choose the EverFocus DDNS server, you can obtain a free host name from EverFocus by following the steps below:

From EverFocus: To obtain a free host name from EverFocus, type a desired host name in the textbox, click the Register / Update button, and then click the Apply button.

From other DDNS server providers: To obtain a domain name from one of the three DDNS server providers, you have to register your name with the provider first, and then select the provider and fill in the required information. Please refer to the specific DDNS company’s website for further information.

Click Apply to apply the setting changes or Reset to reset without saving the changes.

27

EAN Plus Series

Note:

1.

In order to support the full functionality of the camera, you must open the port numbers (80,

554, 443) on the router for remote access to the IP camera. This function is available on most routers in the market and is often known as “Port Forwarding”. To set up Port Forwarding, please consult the manual of the router.

2.

In certain router models, it is possible that you will not be able to access the camera using

DDNS while inside the router’s network. Please try using a PC located outside of your router’s network.

Default Ports on All EverFocus IP Cameras:

HTTP: 80

RTSP: 554

HTTPS: 443

28

EAN Plus Series

7.3.3

SMTP / FTP

Set SMTP Server (email)】This area is for configuring the mail server that is used to send e-mail notifications from the camera to predefined addresses via SMTP. Note that to enable e-mail notification function, you have to check the Send Mail Notification item on the Event dialog box

(see 7.7.1 Event Settings).

SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails.

SMTP Port: Enter the port number for SMTP. The default is 25.

Authentication: Check this box if the SMTP server requires authentication (user/password).

User name: Input the user’s login ID if the SMTP server requires authentication.

Password: Input the user’s login password if the SMTP server requires authentication.

29

EAN Plus Series

Receiver Address: Input the e-mail addresses for receiving an e-mail message when an EVENT is enabled and triggered. Please use “;” to separate multiple addresses.

Sender Address: Input the sender’s e-mail address, so that the receiver can recognize the sender when an Event message is received.

Attach Image: Check this box if you want to attach an image when an alarm is triggered or an IP camera detects events.

Send Test Email: Click the Test button to send a testing email to the assigned address.

Click Apply to apply the setting changes or Reset to reset without saving the changes.

Set FTP Server】The settings relating to the FTP server used to transmit the alarm images can be configured here. Note that to enable uploading images to the FTP server function, you have to check the Upload to FTP item on the Event dialog box (see 7.7.1 Event Settings).

FTP Server: Enter the IP address or the host name of the FTP server.

FTP Port: Enter the port number for the FTP server. Default is 21.

Recording Path: Assign the recording path.

User Name: Set FTP User’s name.

Password: Set FTP password.

PASV mode: Check to enable Passive mode. Passive mode is normally enabled. If a connection cannot be established, uncheck "PASV Mode”.

Test FTP Server: Click the Test button to send a testing file to the assigned FTP server.

Click Apply to apply the setting changes or Reset to reset without saving the changes.

30

EAN Plus Series

7.3.4

HTTPS

Hypertext Transfer Protocol Secure (HTTPS) is a combination of the Hypertext Transfer Protocol and the SSL/TLS protocol and provides encrypted communication and secure identification of a network web server.

Create Certificate To use HTTPS, a Certificate must be created first. There are two ways to create and install a certificate:

Create Self-signed Certificate: A self-signed certificate can be used until a Certificate

Authority-issued certificate has been obtained. Click the Create Self-signed Certificate button to install a self-signed certificate. Although self-signed certificates are free and offer some

protection, true security is only implemented after the installation of a signed certificate issued

by a certificate authority. Enter the required Certificate information as shown below. This info will be displayed on the certificate if anyone wants to inspect it. Enter all required information and click Apply to save it.

31

EAN Plus Series

Create Certificate Request: An official certificate can be requested from an issuing Certificate

Authority by clicking the Create Certificate Request button. Enter all the required info and click Apply to save and send the request.

Created Request】This field will show the Subject field of the created request (see below). The properties of any current certificate request can be viewed by clicking the Property button in this field. To create and install another certificate or request, remove the existing one by clicking the

Remove button to erase the certificate or request.

32

EAN Plus Series

Install Signed Certificate】When the signed certificate is sent back to you from the Issuing

Authority, download it on your computer. Then click the Browse button in this field to search for the file. Click on the file and press the Upload button to import the certificate.

Installed Certificate Information】Once a certificate has been uploaded, this field will show the subject line of the certificate (see the example below).

Press the Property button to view the details of the certificate. A pop-up window will appear with the information (below is an example of the Property pop-up window of a self-signed certificate).

To create and install other certificates, remove the existing one by clicking the Remove button to erase the certificate.

33

EAN Plus Series

7.3.5

SNMP

The default values for SNMP v1/v2/v2c and SNMP v3 are already filled in. Click either of the

Enable buttons to enable either of the two. Make your changes as desired. Click on the Trap

Address field to enter the digits, if required.

7.3.6

Network Alarm

This function works with EverFocus’s CMS software, e.g. the PowerCon or the Power Video Plus. For the setting details, please refer to the CMS network alarm protocol.

34

EAN Plus Series

7.4

Video

The settings relating to video such as streaming, camera OSD can be configured on this page. The

"Video" page has five tabs: Multi-streaming, Camera, Advanced, ROI and Privacy Mask.

7.4.1

Multi Streaming

Stream Settings This IP camera can output three video streams simultaneously. For each of these streams, the user can set the compression format, resolution, bit rate, and frame rate individually.

Stream 1 is always enabled for live view. To enable Stream 2 and/or Stream 3, check the “Enable” box the header of each stream.

Note: If you connect to the camera via the Internet and experience a delay (lag time) in the video feed, try to reduce the number of streams and the quality and resolution of the streams – but keep the frame rate at its maximum.

35

EAN Plus Series

Format: Select the encoding format – H.264 or MJPEG.

Resolution: Select the most suitable resolution for your needs.

Frame Rate: Select from 1 to 30 fps.

Bit Rate: If required, select whether you want the stream to stream a Constant Bit Rate or a

Variable Bit Rate, and set the values of whichever option you choose.

Click Apply to apply the setting changes or Reset to reset without saving the changes.

Video Recording Settings】Select the stream you want to configure and then select whether you want the recording files of that stream to be saved in AVI or ARV format. Click Apply to apply the setting changes or Reset to reset without saving the changes.

Time Stamp Settings You can select the Date/Time format, position, and add the setting to the streaming.

Click Apply to apply the changes, or Reset to reset without saving the changes.

36

7.4.2

Camera

EAN Plus Series

Image Settings】Set the Brightness, Saturation, Contrast or Sharpness of the image. Click Apply to apply the changes, or Reset to reset without saving the changes.

Camera Settings

Mirror: Switch Mirror ON to rotate the image horizontally around a vertical axis.

Flip: Switch Flip ON to rotate the image vertically around a horizontal axis.

AE: There are two options:

ALC: Selecting Automatic Light Control allows the camera circuitry to either take bright spots more into consideration (peak), bringing out detail in bright areas, or less into consideration

(average) bringing out detail in shadows.

AES: Selecting Auto Electronic Shutter disables the Shutter setting below this setting. In this mode, the camera measures the light level and decides whether it needs more or less light and then automatically adjusts the shutter speed accordingly.

BLC: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against a bright background.

OFF: Select to switch Back Light Compensation functions off.

(ON)BLC: The BLC can increase the exposure of a dark area surrounded by a brighter area, HLC can decrease the exposure of bright areas surrounded by darker areas. This enables the camera to better display information that would otherwise have been “whited out”, like a

 license plate between two bright headlights on a dark road.

(ON)HLC: The Highlight-Suppression BLC is used to reduce the brightness of light sources in a specific area. It is activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights, street lights or headlights in the field of view.

37

EAN Plus Series

WDR: The Wide Dynamic Range (WDR) function provides clearer images when both of the very bright and dark areas simultaneously appear on the camera view. There are four value options:

OFF, Low, Middle and High. Note that when WDR is ON, some parts of the image may appear solarized. This is normal for WDR, and is not a camera malfunction. This function is only available for EAN3120 Plus / 3220 Plus.

D/N Mode

Auto: Select to let the camera automatically switch to Night mode (black and white) when the light levels fall to a specified level, and back to Day mode (color) when the light levels rise to a

 specified level.

Day: Select to keep the camera in Day mode (color), even in nighttime.

Night: Select to keep the camera in Night mode (black and white), even in daytime.

38

EAN Plus Series

7.4.3

Advanced

39

EAN Plus Series

Camera Settings

Lens (IRIS Control): Select DC or Manual for IRIS control. This function is only available for EAN3220

Plus / 3520 Plus.

Exposure Settings (AE): This setting is used to adapt to the amount or type of light used by the camera. Note the settings vary among models.

Mode:

This function is not available for EAN3220 Plus.

Automatic Light Control (ALC): This option is only available for EAN3120 Plus / 3300 Plus. The

ALC allows the camera circuitry to either take bright spots more into consideration (peak), bringing out detail in bright areas, or less into consideration (average) bringing out detail in shadows.

Auto Electronic Shutter (AES): This option is only available for EAN3120 Plus / 3300 Plus. In this mode, the camera measures the light level and decides whether it needs more or less light and then automatically adjusts the shutter speed accordingly.

Manual: This option is only available for EAN3300 Plus / 3520 Plus. Select this option to manually set up the Shutter (Manual) and AGC (Manual) values.

Auto: This option is only available for EAN3520 Plus. Select this option to apply the system settings.

Shutter Priority: This option is only available for EAN3520 Plus. Select this option to set up the

Shutter (Manual) values.

Iris: Specify the size of the Iris opening here.

Shutter: If enabled, this setting lets you set the shutter speed yourself.

Shutter Limit: Use this setting to set the maximum shutter speed for the camera. This function is only available for EAN3120 Plus.

AGC: Set the Auto Gain Control limit here. The lower the AGC level, the lower the video signal and the noise. However, the image will be darker under low-light condition with IR-off if you set up the

Iris to the maximum level.

Slow Shutter: This option can be switched on when AES Mode is selected in the Exposure Settings

(AE) field. This function is only available for EAN3220 Plus / 3300 Plus / 3520 Plus.

Flickerless: If the Mode field in the Exposure Settings (AE) area has been set to AES, then this option becomes available. Choose between OFF, 50HZ, 60HZ, 50HZ (High Luminance) or 60HZ (High

Luminance). This function is only available for EAN3300 Plus / EAN3520 Plus.

EV Setting: Set up the Exposure Value. Note the brightness of the screen changes when you change the EV value. This function is only available for EAN3300 Plus.

AE Response: Set up Auto Exposure Response time. This function is only available for EAN3300 Plus.

40

EAN Plus Series

AE Weighting Area: Select an AE Weighting area. Each setup AE Weighting Area is configured with the appropriate brightness level on the center and the surrounding areas. This function is only available for EAN3300 Plus.

Brightness: Set the image brightness here.

AE Reference:

Set the Auto Exposure value here. This function is only available for EAN3120 Plus.

Black Level: Set the Black level here. This function is only available for EAN3300 Plus.

WDR: The Wide Dynamic Range (WDR) function provides clearer images when both of the very bright and dark areas simultaneously appear on the camera view. There are four value options: OFF,

Low, Middle and High. Note that when WDR is ON, some parts of the image may appear solarized.

This is normal for WDR, and is not a camera malfunction. This function is only available for EAN3120

Plus / 3220 Plus / 3520 Plus.

Visibility Enhancement: (OFF/Low/Middle/High) Images in foggy or rain environments or in environments with a very strong luminous intensity have a dynamic range that is significantly lower than ordinary images. The user can use this Visibility Enhancement setting to “DEFOG” the image if such “FOGGING” is an issue. This function is only available for EAN3220 Plus.

BLC Settings: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against a bright background. This function is not available for EAN3520 Plus.

OFF: Select to switch Back Light Compensation functions off.

Back Light: This option is only available for EAN3300 Plus. The Back Light function is useful when the background of the subject is very bright and the subject itself is dark. Select Back

Light and adjust the slide bar to the left / right for setting up the back light value. The higher the value, the more the backlight compensation.

Front Light: This option is only available for EAN3300 Plus. This function is useful when the bright highlights, such as flashlight or car headlights, appear on the camera view. Select Front

Light and adjust the slide bar to the left / right for setting up the front light value. The higher the value, the more the highlight compensation.

ON (BLC): This option is only available when you select AES Mode in the Exposure Settings (AE) field. The option is only available for EAN3120 Plus / 3220 Plus. The BLC function is useful when the background of the subject is very bright and the subject itself is dark. Follow the instructions below to configure the settings for each model:

41

EAN Plus Series

For EAN3120: Select ON (BLC), the active (see image below). Click the

button next to the Mode drop-down list will be

button, the green setup areas appear on the left screen. Click on the areas to enable / disable the BLC function. The selected areas (in green) will be applied with the BLC function.

For EAN3220:

You can configure one area to apply the BLC function. Select ON (BLC), the setup buttons appears (see image below). Select Low / Middle / High from the BLC Gain drop-down list. To set up a BLC area, click the Edit Area button and then click on the blue color tab to turn your mouse cursor into a blue pen. Move the cursor to the position on the right screen where you want the BLC rectangle to start and then click. Move your cursor to the position (diagonally opposing corner) where you want the BLC rectangle to end and then click. The blue area will be applied with the BLC function.

ON (HLC): This option is only available when you select AES Mode in the Exposure Settings (AE) field. The option is only available for EAN3120 Plus / 3220 Plus. This function is useful when the bright highlights, such as flashlight or car headlights, appear on the camera view. Follow the instructions below to configure the settings for each model:

For EAN3120: Select ON (HLC), and then select a level from the drop-down list. The higher the level, the more the highlight compensation.

For EAN3220:

HLC Level: Select a level for the HLC setting. The higher the level, the more the highlight compensation.

HLC Mode: Select All Day / Night mode to apply the HLC function.

HLC Black Mask: Select On / Off to apply the black mask on the selected areas. The over-exposure portions within the selected areas will be applied with the black mask.

42

EAN Plus Series 

Color Tabs: You can set up four HLC areas with different colors. To set up a HLC area, click the 

Edit Area button and then click on the color tab to turn your mouse cursor into a pen of that  color. Move the cursor to the position on the right screen where you want the HLC rectangle  to start and then click. Move your cursor to the position (diagonally opposing corner) where  you want the HLC rectangle to end and then click. Select ON from the color tab drop‐down list. 

The rectangular area with the selected color will be applied with the HLC function.   

 

     

 

Back Light: This option is only available for EAN3300 Plus. The Back Light function is useful  when the background of the subject is very bright and the subject itself is dark. Select Back 

Light and adjust the slide bar to the left / right for setting up the back light value. The higher  the value, the more the backlight compensation. 

 

Front Light: This option is only available for EAN3300 Plus. This function is useful when the  bright highlights, such as flashlight or car headlights, appear on the camera view. Select Front 

Light and adjust the slide bar to the left / right for setting up the front light value. The higher 

 

the value, the more the highlight compensation. 

 

Noise Reduction Settings: This limits the amount of digital “video noise” that is usually found in any  video stream, and helps to reduce file size. The higher the level, the more the reduction. 

For EAN3120 Plus / 3300 Plus / 3520 Plus: 

 

 

 

 

Select ON / OFF to enable / disable the Noise Reduction function. Or select Auto to let the camera  automatically enable / disable the Noise Reduction function. Slide the Level bar to set up the level. 

The higher the level, the more the reduction. 

43

EAN Plus Series

For EAN3220 Plus:

2D DNR: Select ON to enable the 2D DNR function.

3D DNR:

Select ON to enable the 3D DNR function. You can further set up the following settings.

3D Start AGC: Set up the AGC level to automatically start the 3D NR function.

3D End AGC: Set up the AGC level to automatically stop the 3D NR function.

3D Level: Set up the 3D DNR level.

Smart NR: Select ON to enable the Smart NR function. The 3D NR function will be automatically turned on when a motion event occurs.

White Balance Settings: Select the mode that delivers the best quality image for the camera’s light environment. There are five options: Auto, Manual, Indoor, Outdoor, One Push.

Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the camera computes the white balance value output using color information from the entire screen. It outputs the proper value using the color temperature radiating from a black subject based on a range of value from 3000 to 7500K.

Manual: Select to adjust the Red and Blue values yourself in the fields below this field.

Indoor: Select to use the default settings for indoor environments. In the Indoor mode, the camera uses 3200K as the base value.

Outdoor: Select to use the default settings for outdoor environment. In the Outdoor mode, it uses 5800K as the base value.

One Push: Select to enable the Push button next to the Mode drop-down field. This will allow you to force the camera to readjust the white balance every time you push the Push button. The lens will hold the same focal position until the next trigger command is received.

This function helps to prevent incorrect focusing in dark environments. This function is only available for EAN3120 Plus / 3220 Plus.

Manual Temperature: Select to use the optimized Red and Blue settings. You can also optionally adjust the Manual Level below this field for setting up the color temperature. The higher the value, the more the color temperature. This function is only available for EAN3300

Plus.

Day/Night Settings:

Auto: Select to let the camera automatically switch to Night mode (black and white) when the light levels fall to a specified level, and back to Day mode (color) when the light levels rise to a specified level.

Day: Select to keep the camera in Day mode (color), even in nighttime.

Night: Select to keep the camera in Night mode (black and white), even in daytime.

44

EAN Plus Series

IR Smart Settings: Select ON and set up the level to enhance the image quality when the images are over exposure. This function is useful when the camera is in the Night mode. This function is only available for EAN3220 Plus.

Saturation: Set the saturation value. This function is not available for EAN3220 Plus.

Monitor Type: Select a gamma value from Set 1, Set 2 or Set 3. This function is only available for

EAN3120 Plus.

Negative: Switch this setting ON to view a color negative version of the video image. This is useful at night or when viewing temperature-sensitive images. This function is not available for EAN3520

Plus.

Sharpness Settings: Select the sharpness level of the image. A low sharpness level will deliver a softer, less detailed image. A high level will deliver a sharp, highly detailed image. Switch Resolution

Enhancement ON to enable the resolution enhancement function.

Contrast: Select the contrast level of the image.

Suppress Function: This function is only available for EAN3300 Plus.

Aperture Compensation Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress luminance noise when the AGC level increases.

Chroma Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress chrominance noise when the AGC level increases.

Ygamma: (gamma 2.2/standard/contrast enhance/high light range mode L/High light range mode

H). Select the Ygamma value for the video quality of the monitor. This function is only available for

EAN3300 Plus.

Monitor Settings: The user can use this field to optimize video quality for his or her specific type of monitor – LCD or CRT. This function is only available for EAN3220 Plus / 3520 Plus.

Color Space Standard:

The options are YUV601 for SD and YUV709 for HD. These define the color space standard required to convert an RGB picture to a YUV picture. Generally, YUV601 is used for

Standard Definition (720P) devices and the YUV709 is used for High Definition (1080P) devices. This function is not available for EAN3520 Plus.

Click Apply to save all changes. Click Reset to cancel all changes.

45

EAN Plus Series

7.4.4

ROI (Region of Interest)

The Region of Interest (ROI) function allows users to set up multiple regions within an image with better quality and less distortion than the rest of the image. You can also use this function together with the Digital Zoom function on the Live View Page to get a better image result. Up to eight ROIs can be configured in the ROI settings page.

To set up an ROI region:

1.

Select an ROI number from the ROI No. drop-down list.

2.

Click the Add button, the mouse cursor will turn into a pen when you move it over the live image on the left.

3.

Move the cursor to the position where you want the ROI rectangle to start and then click.

Move the cursor to the position (diagonally opposing corner) where you want the ROI rectangle to end and then click.

4.

Slide the Quality bar to set up the quality value.

5.

Click the Apply button to apply the settings, or click the Reset button to reset without saving the settings.

46

EAN Plus Series

7.4.5

Privacy Mask

The Privacy Mask can block out sensitive areas from view, covering the areas with colored or black and white boxes in both live view and recorded clips. This feature is useful when users’ don’t want the sensitive information visible. Up to four Privacy Masks can be configured.

Privacy Mask Color Settings】The Modes vary among camera models.

Mode: Click Color to make the masks appear as colored rectangles on the screen. Click B/W to make the masks appear as gray rectangles on the screen. Click Mosaic to make the masks appear as mosaic-effect rectangles on the screen.

Level: Select the color of the masks if you selected Color Mode. Select the level of grayness of the masks if you selected B/W Mode. Select the level of small/middle/large if you selected Mosaic

Mode.

Click Apply to apply the settings, or click Reset to reset without saving the settings.

Color Tabs

: Click on a color tab to turn your mouse cursor into a pen of that color.

You can now create a block of that color on the video screen. Move your cursor to the position where you want your mask rectangle to start and then click. Move your cursor to the position

(diagonally opposing corner) where you want your mask rectangle to end and then click. The rectangular area with the selected color will appear. The live image will display the rectangular area with the color you selected. If you want to create another mask, use one of the other three colors. Each color denotes a different mask area. Only one block per color is allowed. As the number of colors suggests, you can configure up to four blocks.

47

EAN Plus Series

Select All: Click to turn the whole screen into a mask area.

Clear All: Click to delete all configured mask blocks.

Eraser: Click to turn the mouse cursor into an eraser to delete any block you click on.

Area: Shows the color and number of the block.

Enable: Check this box to enable the related mask block.

Click Apply to apply the settings, or click Reset to reset without saving the settings.

48

EAN Plus Series

7.5

Audio

The EAN Plus series IP camera can transmit audio to your computer if you have connected an external microphone to its audio Input cable. It can also receive audio input from you and transmit it via an external speaker, if you have connected such a speaker to its audio Output cable.

Check the Enable Audio box to enable the camera’s audio function. The camera will now act as a digital bridge (via the IP network) between any connected audio input device and any connected audio device.

Adjust the Audio Input Volume if you have external audio input devices (microphones) connected to the camera and if there are problems with the sound input being too low or high.

Click Apply to save all settings, or click Reset to cancel.

49

EAN Plus Series

7.6

User

7.6.1

User Information

The system administrator can create up to ten user accounts on this page.

To set up a user account:

1.

Highlight a user account and click the Modify button. The following dialog box appears.

2.

Type the account name, account description and password for the account. Type the password again in the Confirm field.

3.

Select an authority level for the user account from the Authority drop-down list.

Supervisor / Administrator: The only difference between a supervisor and administrator is that a supervisor can edit an administrator’s account and password, but an administrator cannot edit the supervisor’s account and password. Multiple administrators can be configured, but there can be only one supervisor. The supervisor and administrators all have unrestricted access to the Settings submenus and can determine the registration of all other users.

50

EAN Plus Series

User: A user can view the Live View page and view the system, network, video, and audio information. A user can only adjust the User Config page settings. The user does not have access to the User, Event and System pages.

Guest: The lowest level of access, which only allows the user access to the Live View page.

4.

Select Active or Disable from the Status drop-down list to active or disable the user account.

5.

Click On in the SD Card Playback field to allow the user to access the SD card playback function.

6.

Click OK.

7.

Click Apply to save all the settings.

51

EAN Plus Series

7.6.2

IP Address Filter

Use this page to specify IP addresses that are not allowed to access this camera. By default, any IP address can access the camera.

Note: The Allowed List addresses only become relevant when the Denied List contains a network or range, and the supervisor wants to allow one or more IP addresses within that excluded range or network. In such a scenario, the user would enter the excluded range or network in the Denied List, and enter the exceptions in the Allowed List.

To set up the IP Address Filter:

1.

Select Denied List. Click the Add button, the following dialog box appears.

2.

Select an IP type from the IP Type drop-down list.

3.

Select a network rule from the Rule drop-down list, type the IP address and click OK.

Single: Type a single IP address in the IP Address field below.

Network: Type the IP address and subnet mask in the field below.

Range: Type a range for the IP addresses.

4.

If you have set up an IP range in Step 3, you can optionally set up the Allowed List to allow one or more IP addresses within the setup IP range to access the IP camera.

5.

Click Apply.

52

EAN Plus Series

7.7

Event

You can set up the Motion Detection event, Tamper Detection event or the Alarm I/O to automatically notify the users when an event occurs or an alarm is triggered. You can also set up a schedule to automatically record the videos when an event occurs or an alarm is triggered.

7.7.1

Event Settings

You can create a total of ten event or alarm settings page in the Event List

Event List

Click the Add button, and the following Event Configuration Window appears.

53

EAN Plus Series

Enter Event Name: Type an event name.

Event Triggered by: Select an event or alarm type for the to-be-specified-below reaction/s.

Alarm Input: Select this if you want a reaction trigger coming from any external, connected sensor to activate a to-be-specified-below reaction/s via the camera system. Make sure that a suitable device is actually connected to the alarm input relay.

Manual Trigger: Select this option if you want to manually trigger the alarm by clicking the Trigger

Event button on the Live View Page.

Motion Detection: Select this option if you want motion in a specified part of the camera’s viewing rectangle (the screen image) to trigger the to-be-specified-below reaction/s.

Tampering Detection: Select this option if you want the camera’s tampering detection sensor to trigger the to-be-specified-below reaction/s.

Schedule Recording: Select this option if you want the Schedule Recording periods configured in the recording schedule (the Settings > Event > Schedule page) to activate this event. In this

 scenario, a preconfigured event reaction like a log entry will list the start and end times of each period. Actual recording will only be triggered if the event is preconfigured to do so.

Enable This Event: Select to activate the event.

Enable Re-trigger: Click to set a minimum time after the event is triggered before the event can be triggered again.

Enable Pre-trigger Buffer: Click if you want the Event reaction (as selected in the “Notification

Over” field below) to be the activation of the video recording function, and if you want the recording to include the video feed from the time period (configurable on the previous “Event

Settings” page) just before the Event trigger occurred.

Enable Post-trigger Buffer: Click if you want the Event reaction (as selected in the Notification

Over field) to be the activation of the video recording function, and if you want the recording to include the video feed from a time period (configurable on the Event Settings page) just after the Event trigger occurred.

Motion Area: Select a setup motion detection area from the drop down list. Note this function only becomes relevant after the Motion Detection areas have been set up (see 7.7.2

Motion Detection).

Notification Over: Select the desired notification types form the following items.

Log: Click if you want the camera to list the event’s details in its log if the event is triggered.

Trigger Alarm Output: Click if you want the camera to relay the event reaction to a device attached to the alarm relay output wire and then set up the alarm output duration time.

54

EAN Plus Series

Send Mail Notification: Click if you want the camera to send an Event notification email to the email address entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event occurs (see 7.3.3 SMTP / FTP).

Upload to FTP: Click if you want the camera to upload recorded footage to the FTP server entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event occurs (see 7.3.3 SMTP / FTP).

Record to SD Card: Click if you want the camera to start recording its video feed (when the event occurs) on an on-camera SD Card (if such a card has been inserted).

Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers, so make sure you enable at least one of these buffers, especially the Post-trigger Buffer.

Record to PC: Check this box if you want the camera to start recording its video feed (when the event occurs) on the same folder on the same PC as configured on the User Config > User

Config page (if such a folder has been enabled and configured).

Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers (and for as long as the event trigger is happening – e.g. a motion is detected), so make sure you enable at least one of these buffers, especially the Post-trigger Buffer.

Network Alarm: Check this box if you want the camera to send a network alarm signal (when the event occurs) to the CMS servers configured on the Network > Network Alarm page (see

7.3.6 Network Alarm).

Click OK to save all settings, or click Cancel to cancel.

Pre/Post Trigger Settings

Pre-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage

(length of time) before the event trigger moment that will be included in an event-triggered video recording, if that buffer and video recording has been enabled in the Event Configuration Window.

Post-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage

(length of time) after the event trigger moment that will be included in an event-triggered video recording, if that buffer and video recording has been enabled in the Event Configuration Window.

Click Apply to save all settings, or click Reset to cancel.

55

EAN Plus Series

7.7.2

Motion Detection

Use this page to configure up to four areas in which motion will be detected. When a motion is detected by the camera, the motion detection icon will appear at the top right of the

Live page to alert the user. This function can also be linked with correctly configured Events to trigger Event reactions like the activation of video recording periods, snapshots, alarms, etc.

Color Tabs

: Click on a color tab to turn your mouse cursor into a pen of that color.

You can now create a block of that color on the video screen. Move your cursor to the position where you want your detection rectangle to start and then click. Move your cursor to the position

(diagonally opposing corner) where you want your detection rectangle to end and then click. The rectangular area with the selected color will appear. This block will be an area inside which the camera will detect motion. If you want to create another detection area, use one of the other three palette colors. Each color denotes a different detection area. Only one block per color is allowed. As the number of colors suggests, you can configure up to four blocks.

Select All: Click to turn the whole screen into a motion detection area.

Clear All: Click to delete all configured motion detection blocks.

Eraser: Click to turn your mouse cursor into an eraser to delete any block you click on.

Area: Shows the color and number/ID of the block.

Enable: Check this box to enable the related motion detection block.

Sensitivity: Set the sensitivity of the motion detection sensor function.

Click Apply to save all settings, or click Reset to cancel.

56

EAN Plus Series

7.7.3

Tamper Detection

Use this page to set the number of seconds that an alarm signal will be active if the device is physically tampered (moved, covered up, or out of focus.

7.7.4

Alarm I/O

Use this page to set the type of trigger input and the type of output contact for the camera’s alarm channel.

57

EAN Plus Series

7.7.5

Schedule

Use this page to configure a schedule for periods during which the camera should deactivate all user-activated Events (gray Deselect periods), or when the camera should deactivate all user-activated Events, except Schedule Recording (SR) events (blue Schedule Recording-only periods), or when the camera should deactivate only SR events (red Event Recording-only periods), or when it should enable all activated Events (yellow periods).

Event Recording: Click this button to make every hour block you click on red. A red block represents an Event Recording-only block, which represents an hour when the camera will deactivate all preconfigured, activated Schedule Recording events and keep all the other activated events active.

Schedule Recording: Click this button to make every hour block you click on blue. A blue block represents a Schedule Recording-only block, which represents an hour when the camera will deactivate all other preconfigured, activated events and keep only the preconfigured, activated

Schedule Recording events active.

Event + Schedule: Click this button to make every hour block you click on yellow. A yellow block represents an hour in which all activated events, including Schedule Recording events, will be active.

Deselect: Click this button to make every hour block become grey. A grey block represents an hour in which all activated events, including Schedule Recording events, will be inactive.

Click Apply to save all settings, or click Reset to cancel.

58

EAN Plus Series

7.8

System

You can set up the system’s time and SD card settings, and to do maintenance and reset actions like reboots and upgrades.

7.8.1

Date/Time

Machine Name Settings】If required, enter a new name for the machine. This name will be visible in the Machine Name field of the IP Utility software, which is included in the software CD.

Set Time Zone】Set the time zone of the camera’s location.

Set Date/Time Manually】Set the date/time here if you won’t be using an NTP server to update the date/time (see below).

Set Date/Time Sync.】Enter the Network Time Protocol server, if applicable. The camera’s time will be automatically adjusted by synchronizing with the NTP server.

Click Apply to save all settings, or click Reset to cancel.

59

EAN Plus Series

7.8.2

Daylight Saving

Click Enable Daylight Saving to enable this schedule, and select the dates when the region’s daylight saving period begins and ends. Click Apply to save all settings, or click Reset to cancel.

7.8.3

SD Card

Use this page to prepare the system for safely removing the SD Card from its slot.

Setup SD Card

Notification: Select the percentage of storage space that should be left on the card before the camera notifies you of the impending storage shortage or overwrite.

Event Recording: Select if you want Event Recording only, FTP Backup only, or both.

Overwrite: Click ON if you want the card to start writing over recorded footage when its memory is full. Click OFF if you want the card to stop recording new footage when its memory is full.

SD Card Utility

Capacity: This shows you how much card memory has been used and how much memory capacity remains on the card.

Remove: Click this button before removing the card from the system.

Format: Click this button to format the card. All data saved on the SD card will be removed if the card is formatted.

60

EAN Plus Series

7.8.4

Maintenance

Maintenance Server

Reboot: Click this button to reboot the unit without changing any of the settings. Use this function if the unit is not behaving as expected.

Restore: Click this button to restart and reset most of the current settings to their factory default values. The only settings that will not be changed to default are:

IP settings

DDNS settings

Default: The Default button should be used with caution. Pressing this button will return all of the camera's settings, including the IP address, to the factory default values. The camera will then have to be reconfigured.

Save/Load Configuration Server

Save: To make a backup file of the machine’s current configurations, press Save to save all the configurations to a config. file. This will enable the user to reload these configuration settings if the settings are changed and there is unexpected behavior.

Load: To load a previously saved configuration, press the Browse button to locate the saved config. file (see above) and then click the Load button. The system’s settings will be restored to the saved configuration.

61

EAN Plus Series

Save/Load Video Configuration Server

Save: To make a backup file of the machine’s video configurations, press Save to save the video configurations to a config. file. This will enable the user to reload these configuration settings if the settings are changed and there is unexpected behavior.

Load: To load a previously saved video configuration, press the Browse button to locate the saved config. file (see above) and then click the Load button. The system’s settings will be restored to the saved video configuration.

Upgrade Firmware】Click the Browse button to find a previously prepared firmware upgrade file.

Click Upgrade to install the new firmware.

Note:

1.

Do not disconnect power to the unit during the upgrade sequence. The unit will reboot automatically after the upgrade has completed (1-5 minutes).

2.

During the upgrade process, all event recording actions will be stopped. Event recording actions will resume after the camera is rebooted.

62

EAN Plus Series

8.

Upgrading Firmware Using IP Utility

You can upgrade the Firmware using the IP Utility software included in the software CD.

1.

Install and then start the IPU program

. The following dialog box appears.

2.

Click Find Devices to search the cameras connected in the LAN. The default network values of the

cameras will be displayed. By default, the network protocol of the camera is DHCP.

3.

Click Login/Multi Login to log in the camera.

4.

Type the user ID and password. Click OK.

Note:

1.

The default user ID is user1 and the default password is 11111111.

2.

If you select more than one camera that has the same user ID / password, you will be able to log in several cameras at once.

63

EAN Plus Series

5.

Highlight the camera and then click Upgrade Firmware. A browsing window appears.

6.

Select the firmware file (.evb) and then click Open. The IP Utility will automatically upgrade the

firmware.

The camera will reboot once the update is complete. Click Find Devices, the new firmware version

should be displayed in the last part of the Machine Name.

64

EAN Plus Series

9.

Specifications

Model EAN3120 Plus EAN3220 Plus EAN3300 Plus EAN3520 Plus

Camera

Image Sensor

Megapixel

1/3" Panasonic CMOS

1.3 MP 2 MP

1/2.8" Sony CMOS

3 MP

Picture Elements (H x V) 1280 x 1024 1944 x 1092 2048 x 1536

1/2.5" Aptina CMOS

5 MP

2560 × 1920

Min. Illuminations

Electronic Shutter

0.03 Lux at F1.4

1/60 ~ 1/60,000 sec.

Scanning System

WDR

BLC

Gain Control

NTSC / PAL

Yes

Yes

Yes

Yes

Yes No Yes

White Balance

Lens

Mounting Type

Day / Night

IRIS Control

C / CS

Yes (with removable auto IR-cut filter)

DC Electrical IRIS / Lens IRIS

Video

Video Compression

H.264 / MJPEG

2560 x 1920, 2560 x 1600, 2560 x 1440 (for EAN3520 Plus only)

2048 x 1536, 1920 x 1200 (for EAN3520 Plus / 3300 Plus only)

1920 x 1080 (for EAN3520 Plus / 3300 Plus / 3220 Plus only)

1280 x 1024, 1280 x 720, 1024 x 768, 720 x 480, 704 x 480, 640 x 480,

352 x 240, 320 x 240, 160 x 120

Resolution

NTSC

Frame Rate

PAL

2560 x 1920, 2560 x 1600, 2560 x 1440 (for EAN3520 Plus only)

2048 x 1536, 1920 x 1200 (for EAN3520 Plus / 3300 Plus only)

1920 x 1080 (for EAN3520 Plus / 3300 Plus / 3220 Plus only)

1280 x 1024, 1280 x 720, 1024 x 768, 720 x 576, 704 x 576, 640 x 480,

352 x 288, 320 x 240, 160 x 120

30 fps at

1280 x 1024

30 fps at

1920 x 1080

15 fps at

2048 x 1536

15 fps at

2560 × 1920

Audio

Audio Streaming

Audio Compression

Two-way audio

G.711

65

EAN Plus Series

Network

Interface

Supported Protocols

10 / 100 Base-T Ethernet, RJ-45 socket

TCP/IP, IPV6, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, SNMP, FTP,

HTTP, HTTPs, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP, IGMP, ARP, ONVIF,

PSIA

Connector

Power

Ethernet

Audio

Alarm I/O Terminal

Local Storage

TV-Out

General

Power Source

Power Consumption

(IR LEDs On)

DC female port / PoE

RJ-45

1 In (phone jack for microphone)

1 Out (phone jack for Speaker)

I/O wires

Micro SD / SDHC memory card slot

BNC socket, composite 1 V p-p / 75 Ω

DC 12V / PoE (IEEE802.3af)

5W (DC 12V)

6.21W (PoE)

5W (DC 12V)

5.22W (PoE)

Operating Temperature

0°C ~ +50°C / 32°F ~ +122°F

Humidity

Safety

20% to 80% (no condensation)

CE, FCC

Dimensions (L x W x H)

117 x 56 x 68 mm / 4.6 x 2.2 x 2.7 in

Weight

410 g / 0.9 lb

5W (DC 12V)

5.36W (PoE)

5.04W (DC 12V)

5.28W (PoE)

66

EverFocus Electronics Corp.

EverFocus Taiwan:

12F, No.79, Sec. 1, Shin-Tai Wu Road,

Hsi-Chih, Taipei, Taiwan

TEL: +886 2 2698 2334

FAX: +886 2 2698 2380 www.everfocus.com.tw [email protected]

EverFocus China - Beijing:

Room 609, Technology Trade Building,

Shangdi Information Industry Base,

Haidian District, Beijing 100085, China

TEL: +86 10 6297 3336~39

FAX: +86 10 6297 1423 www.everfocus.com.cn [email protected]

EverFocus USA - California:

1801 Highland Avenue, Unit A, Duarte, CA 91010, USA

TEL: +1 626 844 8888

FAX: +1 626 844 8838 www.everfocus.com [email protected]

EverFocus Europe - Germany:

Albert-Einstein-Strasse 1, D-46446

Emmerich, Germany

TEL: +49 2822 93940

FAX: +49 2822 939495 www.everfocus.de [email protected]

EverFocus China - Shenzhen:

4F, No. 2, D4 Building, Wan Yelong

Industrial Park, Tangtou Road, Shiyan,

Baoan, Shenzhen, Guangdong 518101, China

TEL: +86 755 2765 1313

FAX: +86 755 2765 0337 www.everfocus.com.cn [email protected]

EverFocus USA - New York:

415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA

TEL: +1 631 436 5070

FAX: +1 631 436 5027 www.everfocus.com [email protected]

EverFocus Japan:

5F, Kinshicho City Building, 2-13-4 Koto-Bashi,Sumida-Ku,

Tokyo, 130-0022, Japan

TEL: +81 3 5625 8188

FAX: +81 3 5625 8189 www.everfocus.co.jp [email protected]

EverFocus India:

Suite 803, Housefin Bhavan, C-21,

Bandra Kurla Complex, Bandra (East),

Mumbai 400051, India

TEL: +91 22 6128 8700

FAX: +91 22 6128 8705 www.everfocus.in [email protected]

Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.

Please, dispose of this equipment at your local community waste collection/recycling centre.

In the European Union there are separate collection systems for used electrical and electronic product.

Please, help us to conserve the environment we live in!

EverFocus Europe - UK:

Unit 12, Spitfire Business Park,

Hawker Road, Croydon Surrey, CR0 4WD, UK

TEL: +44 20 8649 9757 / +44 845 430 9999

FAX: +44 20 8649 9907 www.everfocusuk.co.uk [email protected]

Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und

Komponenten, die recycelt und wieder verwendet werden können.

Dieses Symbol bedeutet, dass elektrische und elektronische Geräte am

Ende ihrer Nutzungsdauer vom

Hausmüll getrennt entsorgt werden sollen.

Bitte entsorgen Sie dieses Gerät bei

Ihrer örtlichen kommunalen

Sammelstelle oder im Recycling Centre.

Helfen Sie uns bitte, die Umwelt zu erhalten, in der wir leben

!

P/N: 4605PQ3120B010A-Ver.B

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals