User Preferences. Zebra CS6080
ಜಾಹಿರಾತು
ಜಾಹಿರಾತು
User Preferences
Introduction
You can program the digital scanner to perform various functions, or activate different features. This chapter describes each user preference feature and provides programming barcodes for selecting these features.
The digital scanner ships with the settings shown in
(also see
for all defaults). If the default values suit requirements, programming is not necessary.
To set feature values, scan a single barcode or a short barcode sequence. The settings are stored in non-volatile memory and are preserved even when the digital scanner is powered down.
NOTE:
Most computer monitors allow scanning the barcodes directly on the screen. When scanning from the screen, be sure to set the document magnification to a level where you can see the barcode clearly, and bars and/or spaces are not merging.
This is only necessary upon the first power-up when connected to a new host.
To return all features to default values, see
Default Parameters on page 66 . Throughout the programming
barcode menus, asterisks indicate (
*
) default values.
*
Indicates Default
*
High Volume
(0)
Feature/Option
Option Value
62
User Preferences
Scanning Sequence Examples
In most cases, scanning one barcode sets the parameter value. For example, to set the beeper tone to high, scan the
High Frequency
(beeper tone) barcode listed under Beeper Tone on page 70 . The digital
scanner issues a fast warble beep and the LED turns green, signifying a successful parameter entry.
Other parameters, such as
Serial Response Time-Out
or
Data Transmission Formats
, require scanning several barcodes. See these parameter descriptions for this procedure.
Errors While Scanning
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter.
User Preferences Parameter Defaults
lists defaults for user preferences parameters. To change the default values:
•
Scan the appropriate barcodes in this guide. These new values replace the standard default values in
memory. To recall the default parameter values, see Default Parameters on page 66 .
•
Configure the digital scanner using the 123Scan
).
configuration program (see 123Scan and Software
See Standard Parameter Defaults on page 366
for all user preferences, hosts, symbologies, and miscellaneous default parameters.
Table 10
User Preferences Parameter Defaults
Parameter
Parameter
Number
1
SSI Number
User Preferences
Set Default Parameter
Parameter Barcode Scanning
Beep After Good Decode
Direct Decode Indicator
Beeper Volume
Beeper Tone
Beeper Duration
Suppress Power Up Beeps
Decode Pager Motor
Decode Pager Motor Duration
Night Mode Trigger
236
56
859
140
145
628
721
613
626
1215
ECh
38h
F2h 5Bh
8Ch
91h
F1h 74h
F1h D1h
F1h 65h
F1h 72h
F8h 04h BFh
Night Mode Toggle N/A N/A
1
2
Scan Button Sensitivity 2133 F8 08 55
Parameter number decimal values are used for programming via RSM commands.
SSI number hex values are used for programming via SSI commands.
2
Default
Restore Defaults
Enable
Enable
Disable
High
Medium
Medium
Do Not Suppress
Enable
150 msec
Disable
N/A
Normal Touch
Page
Number
63
User Preferences
Table 10
User Preferences Parameter Defaults (Continued)
Parameter
Programmable Button Sensitivity
Haptic Feedback (Vibrate) on Button Touch
Click on Button Touch
Scan Button ADF Rule Selection
Parameter
Number
1
2134
1251
1252
2070
Programmable Button ADF Rule Selection
Hands-Free ADF Rule Selection
Lamp Mode Control
2071
2072
1711
SSI Number
2
F8 08 56
F8h 04h E3h
F8h 04h E4h
SSI # F8h 08h
16h
(SSI # F8h 08h
17h)
(SSI # F8h 08h
18h)
F8h 06h AFh
Default
Normal Touch
Enable
Enable
No Action
No Action
No Action
Disable
(SR configurations)
Lamp Mode Timeout
Low Power Mode
Time Delay to Low Power Mode
Timeout to Low Power Mode from Auto Aim
(Applies to cordless configurations only)
1712
128
146
729
Battery Preservation Mode
(Applies to cordless configurations only)
Hand-Held Trigger Mode
1765
138
Hands-Free Mode
Hand-Held Decode Aiming Pattern
630
306
Hands-Free (Presentation) Decode Aiming Pattern 590
F8h 06h B0h
80h
92h
F1h D9h
F8h 06h E5h
8Ah
F1h 76h
F0h 32h
F1h 4Eh
Enable Lamp Mode without Scanning
(HC configurations)
5 Minutes
Enable
1 sec
15 sec
Enable
1
2
Picklist Mode
Virtual Tether Alarm Configuration
Delay Before Virtual Tether Alarm Activates
Virtual Tether Alarm Duration
Defeat Virtual Tether Alarm
Pause Virtual Tether Alarm Duration
Continuous Barcode Read
Unique Barcode Reporting
Decode Session Timeout
Hands-Free Decode Session Timeout
402
2053
2054
2055
2119
2120
649
723
136
400
F0h 92h
F8h 08h 05h
F8h 08h 06h
F8h 08h 07h
F8h 08h 47h
F8h 08h 48h
F1h 89h
F1h D3h
88h
F0h 90h
Parameter number decimal values are used for programming via RSM commands.
SSI number hex values are used for programming via SSI commands.
Level
Enable
Enable
Disable Hands-Free
Decode Aiming Pattern
Disabled Always
Disable
30 Seconds
5 Minutes
Pause Alarm on Scan
Button
30 Seconds
Disable
Enable
9.9 sec
15
Page
Number
64
User Preferences
Table 10
User Preferences Parameter Defaults (Continued)
Parameter
Timeout Between Decodes, Same Symbol
Timeout Between Decodes, Different Symbols
Triggered Timeout, Same Symbol
Mobile Phone/Display Mode
PDF Prioritization
PDF Prioritization Timeout
Decoding Illumination
Illumination Brightness - Hand-Held
Illumination Brightness - Hands-Free
Low Light Scene Detection
720
298
669
2118
810
Parameter
Number
1
137
144
724
716
719
SSI Number
2
89h
90h
F1 D4
F1h CCh
F1h CFh
F1h D0h
F0h 2Ah
F1h 9Dh
F8h 08h 46h
F2h 2Ah
F8h 97h
F2h 5Ah
F8h 05h 01h
F8h 06h BDh
F8h 06h AEh
0
0
0.5 sec
0.1 sec
Disable
Default
Page
Number
Normal
Disable
200 ms
Enable
High
Medium
No Low Light Scene
Detection
Low
Less Motion Tolerance
Host Type Unique
1
2
Scene Detect Sensitivity 1943
Motion Tolerance (Hand-Held Trigger Mode Only) 858
Product ID (PID) Type 1281
Product ID (PID) Value
ECLevel
Miscellaneous Options
Add an Enter Key
1725
1710
Transmit Code ID Character
Prefix Value
Suffix 1 Value
Suffix 2 Value
Scan Data Transmission Format
N/A
45
99, 105
98, 104
100, 106
235
FN1 Substitution Values
Transmit “No Read” Message
Unsolicited Heartbeat Interval securPharm Decoding securPharm Output Formatting
Programmable Button for Single Press
103, 109
94
1118
1752
1753
2060
Programmable Button for Double Press 2103
N/A
2Dh
63h, 69h
62h, 68h
64h, 6Ah
EBh
67h, 6Dh
5Eh
F8h 04h 5Eh
F8h 06h D8h
F8h 06h D9h
F8h 08h 0Ch
F8h 08h 37h
Parameter number decimal values are used for programming via RSM commands.
SSI number hex values are used for programming via SSI commands.
N/A
None
7013 <CR><LF>
7013 <CR><LF>
Data As Is
7013 <CR><LF>
Disable
Disable
Disable
No Formatting
Apple Show/Hide
Keypad
No Action
65
User Preferences
Parameters
Default Parameters
The digital scanner can be reset to two types of defaults: factory defaults or custom defaults. Scan the appropriate barcode below to reset the digital scanner to its default settings and/or set the digital scanner current settings as the custom default.
• Restore Defaults
- Resets all default parameters as follows:
•
If custom default values were configured (see
Write to Custom Defaults
), the custom default values are set for all parameters each time the
Restore Defaults
barcode below is scanned.
•
If no custom default values were configured, the factory default values are set for all parameters each time the
Restore Defaults
barcode below is scanned. (For factory default values, see
.)
• Set Factory Defaults
- Scan the
Set Factory Defaults
barcode below to eliminate all custom default values and set the digital scanner to factory default values (For factory default values, see
• Write to Custom Defaults
- Custom default parameters can be configured to set unique default values for all parameters. After changing all parameters to the desired default values, scan the
Write to
Custom Defaults
barcode below to configure custom defaults.
*
Restore Defaults
Set Factory Defaults
Write to Custom Defaults
66
User Preferences
Parameter Barcode Scanning
Parameter # 236 (SSI # ECh)
To disable the decoding of parameter barcodes, including the
Set Defaults
parameter barcodes, scan the
Disable Parameter Scanning
barcode below. To enable decoding of parameter barcode, scan
Enable
Parameter Scanning
.
*
Enable Parameter Barcode Scanning
(1)
Disable Parameter Barcode Scanning
(0)
Beep After Good Decode
Parameter # 56 (SSI # 38h)
Scan a barcode below to select whether or not the digital scanner beeps after a good decode. If selecting
Do Not Beep After Good Decode
, the beeper still operates during parameter menu scanning and to indicate error conditions.
*
Beep After Good Decode (Enable)
(1)
Do Not Beep After Good Decode (Disable)
(0)
67
User Preferences
Direct Decode Indicator
Parameter # 859 (SSI # F2h 5Bh)
This feature is only supported in Auto Aim and Standard (Level) trigger modes. Scan a barcode below to select optional blinking of the illumination on a successful decode
• Disable Direct Decode Indicator
- illumination does not blink on a successful decode.
• 1 Blink
- illumination blinks once upon a successful decode.
• 2 Blinks
- illumination blinks twice upon a successful decode.
*
Disable Direct Decode Indicator
(0)
1 Blink
(1)
2 Blinks
(2)
68
User Preferences
Beeper Volume
Parameter # 140 (SSI # 8Ch)
To select a beeper volume, scan the
Low Volume, Medium Volume
, or
High Volume
barcode.
Low Volume
(2)
Medium Volume
(1)
*
High Volume
(0)
69
User Preferences
Beeper Tone
Parameter # 145 (SSI # 91h)
To select a beeper tone, scan one of the following barcodes.
Off
(3)
Low Tone
(2)
*
Medium Tone
(1)
High Tone
(0)
Medium to High Tone (2-tone)
(4)
70
User Preferences
Beeper Duration
Parameter # 628 (SSI # F1h 74h)
To select the duration for the beeper, scan one of the following barcodes.
Short
(0)
*
Medium
(1)
Long
(2)
Suppress Power Up Beeps
Parameter # 721 (SSI # F1h D1h)
Scan a barcode below to select whether or not to suppress the digital scanner power-up beeps.
*
Do Not Suppress Power Up Beeps
(0)
71
Suppress Power Up Beeps
(1)
User Preferences
Decode Pager Motor
Parameter # 613 (SSI # F1h 65h)
The scanner includes a pager motor which, when enabled, vibrates the scanner for a period of time when a successful decode occurs.
Scan a barcode below to enable or disable the pager motor. If enabled, scan the appropriate barcode to
set the period of time in which to vibrate the scanner (see Decode Pager Motor Duration
below).
Pager Motor Disable
(0)
* Pager Motor Enable
(1)
Decode Pager Motor Duration
Parameter # 626 (SSI # F1h 72h)
* 150 msec
(15)
200 msec
(20)
72
User Preferences
Decode Pager Motor Duration (continued)
250 msec
(25)
300 msec
(30)
400 msec
(40)
500 msec
(50)
600 msec
(60)
750 msec
(75)
73
User Preferences
Night Mode
Parameter # 1215 (SSI # F8h 04h BFh)
The Night Mode feature allows the user to easily switch to a quiet mode in order to use the pager motor with the beeper off.
Enter and exit Night Mode in one of two ways:
•
Scan
Enable Night Mode Trigger (1) on page 75 and use the trigger to toggle between entering and
exiting Night Mode.
•
Scan the
Toggle Night Mode on page 75 to enter or exit Night Mode, regardless of the state of the
Night Mode Trigger
parameter.
Entering Night Mode:
•
Enables
Decode Pager Motor
•
Disables
Beep After Good Decode
.
•
Disables
Beep on Insertion
.
•
Disables the page beep if the
Page Button on page 161 is enabled (the LED and vibrate features
remain enabled).
•
Disables the Bluetooth disconnect beep.
•
Vibrates the pager motor.
Exiting Night Mode:
•
Returns the scanner to the previously programmed states for the parameter changes above. For example, if
Beep After Good Decode
was enabled before entering Night Mode, it returns to enabled upon exiting night mode.
•
Sounds two short beeps.
In Night Mode:
•
Scanning the pairing barcode activates the pager motor instead of the warble beep and, on pairing connection, the pager motor re-activates.
•
Scanning a default parameter barcode exits Night Mode.
•
Removing the scanner battery exits Night Mode.
•
If the scanner loses power due to a dead battery or
Battery Off
is scanned, the scanner exits Night
Mode on the next power up and resumes normal operation.
For scanners that do not use a pager motor (non-HC units), scanning any Night Mode or pager motor parameters sounds an error beep.
Night Mode Trigger
Enable this to use the trigger to toggle between entering and exiting Night Mode. To toggle, point the scanner away from a barcode, press the trigger until the beam goes off, and then continue pressing the trigger for an additional 5 seconds. Note that pressing the trigger an additional 5 seconds after decoding a barcode has no affect.
74
User Preferences
When entering Night Mode, the pager motor vibrates. When exiting Night Mode, the scanner emits two short beeps.
Enable Night Mode Trigger
(1)
* Disable Night Mode Trigger
(0)
Night Mode Toggle
To toggle between entering and exiting Night Mode without using the trigger, scan this barcode. This functions regardless of the state of the
Night Mode Trigger
parameter.
When scanning this barcode, the pager motor vibrates when entering Night Mode, and the scanner emits two short beeps when exiting Night Mode.
Toggle Night Mode
75
User Preferences
Scan Button Sensitivity
Parameter # 2133 (SSI # F8 08 55)
To adjust the force required to activate the Scan Button, scan one of the barcodes below.
*
Normal Touch
(0)
Light Touch
(1)
Programmable Button Sensitivity
Parameter # 2134 (SSI # F8 08 56)
To adjust the force required to activate the Programmable Button, scan one of the barcodes below.
*
Normal Touch
(0)
Light Touch
(1)
76
User Preferences
Haptic Feedback (Vibrate) on
Button
Touch
Parameter # 1251 (SSI # F8h 04h E3h)
The scanner provides haptic feedback which, when enabled, vibrates the scanner upon a button
touch.
Scan one of the following barcodes to enable or disable this parameter.
* Enable Haptic Feedback (Vibrate) on
Button
Touch
(1)
Disable Haptic Feedback (Vibrate) on
Button
Touch
(0)
Click o
n
Button
Touch
Parameter # 1252 (SSI # F8h 04h E4)
Scan one of the following barcodes to enable or disable a click upon a button
touch.
* Enable
Click
on
Button
Touch
(1)
Disable
Click
on
Button
Touch
(0)
ADF Rule Selection
ADF Rule Selection allows for different ADF rules to be applied to decode data depending on how the data was scanned. On the CS6080 scanner, data can be scanned using the Scan Button, the Programmable
Button or in Presentation Mode.
77
User Preferences
Scan Button ADF Rule Selection
Parameter #2070 (SSI # F8h 08h 16h)
* No Action
(0)
Use Rule 1
(1)
Use Rule 2
(2)
Use Rule 3
(3)
Use Rule 4
(4)
Use Generic Rules
(0xff)
78
User Preferences
Programmable Button ADF Rule Selection
Parameter #2071 (SSI # F8h 08h 17h)
* No Action
(0)
Use Rule 1
(1)
Use Rule 2
(2)
Use Rule 3
(3)
Use Rule 4
(4)
Use Generic Rules
(0xff)
79
User Preferences
Hands-Free ADF Rule Selection
Parameter #2072 (SSI # F8h 08h 18h)
* No Action
(0)
Use Rule 1
(1)
Use Rule 2
(2)
Use Rule 3
(3)
Use Rule 4
(4)
Use Generic Rules
(0xff)
80
User Preferences
Lamp Mode
Lamp Mode uses the scanner to illuminate the workspace around the scanner by providing continuous illumination on demand. Lamp Mode may be enabled or disabled. Once enabled, Lamp Mode is activated or deactivated by pressing the Programmable Button on the scanner. Lamp Mode may be enabled with the option to allow barcode scanning, or not.
Lamp Mode Control
Parameter #1711 (SSI # F8h 06h AFh)
This parameter enables or disables the Lamp Mode feature.
NOTE:
The default value for Healthcare configurations of the scanner is
Enable Lamp Mode without
Scanning
.
The default value for SR configurations of the scanner is
Disable Lamp Mode
.
Enable Lamp Mode with Scanning
(1)
* Enable Lamp Mode without Scanning
(2)
(default for HC models)
* Disable Lamp Mode
(0)
(default for SR models)
81
User Preferences
Lamp Mode Timeout
Parameter #1712 (SSI # F8h 06h B0h)
This parameter controls how long the lamp remains on for when Lamp Mode is enabled.
1 Minute
(1)
* 5 Minutes
(5)
Low Power Mode
Parameter # 128 (SSI # 80h)
NOTE:
Applies to cordless configurations only.
This parameter determines whether or not the digital scanner enters low power mode after a decode attempt.
If disabled, power remains on after each decode attempt.
Disable Low Power Mode
(0)
*
Enable Low Power Mode
(1)
82
User Preferences
Time Delay to Low Power Mode
Parameter # 146 (SSI # 92h)
NOTE:
This parameter only applies when Low Power Mode is enabled.
This parameter sets the time the digital scanner remains active before entering low power mode. The digital scanner wakes upon trigger press or when the host attempts to communicate with the digital scanner.
100 msec
(65)
500 msec
(69)
* 1 Sec
(17)
2 sec
(18)
3 sec
(19)
83
Time Delay to Low Power Mode (continued)
User Preferences
4 sec
(20)
5 sec
(21)
10 sec
(26)
15 sec
(27)
84
User Preferences
Timeout to Low Power Mode from Auto Aim
Parameter # 729 (SSI # F1 D9)
This parameter sets the time the scanner remains in auto aim before entering Low Power Mode.
Disabled
(0)
5 sec
(5)
* 15 sec
(11)
30 sec
(13)
1 minute
(17)
85
User Preferences
Battery Preservation Mode
Parameter # 1765 (SSI # F8h 06h E5h)
NOTE:
This parameter only applies to cordless operation.
Battery Preservation Mode preserves the battery charge when the digital scanner is not being used for an extended period of time.
•
Scan
Enable Battery Preservation Mode
to internally disconnect the battery from the digital scanner when the digital scanner is unused and not being charged for five hours
1
. In this mode the scanner completely turns off. This preserves the battery charge as there is no current drain on the battery and significantly extends battery shelf life. To exit Battery Preservation Mode
2
and return to normal operation either press the digital scanner trigger or return to charging. The digital scanner cannot scan until the wake up process is complete
3
. This takes a few seconds. The amount of time before the battery disconnects from the scanner can be set via
Battery Preservation Timeout Value
below.
NOTE:
1
Five hours is the default timeout value but can be changed via
Battery Preservation Timeout
Value
.
2
Low Power Mode (
82 ) must be enabled for Battery Preservation Mode to take effect.
3
When asleep in Battery Preservation Mode, the digital scanner cannot be accessed for remote management.
To return back to normal operation, insert the scanner back into the cradle to complete the wake up process.
•
Scan
Disable Battery Preservation Mode
to keep the battery connected to the digital scanner at all times. This prevents the battery from being disconnected from the scanner after hours of sitting idle (no scanning) and not charging. When Battery Preservation Mode is disabled, substantial battery shelf life improvements are not gained as compared to when Battery Preservation Mode is enabled.
•
Scan
Battery Preservation Timeout
followed by 3 digits in Numeric Barcodes on page 438 to select a
different battery preservation timeout value (the default for battery preservation timeout is five hours).
For example, if the preservation timeout value should be 12 hours, scan
Battery Preservation
Timeout
below, then scan
0
,
1
, and
2
. To correct an error or change the selection, scan
.
86
User Preferences
*
Enable Battery Preservation Mode
(5)
Disable Battery Preservation Mode
(0)
Battery Preservation Timeout Value
Hand-Held Trigger Mode
Parameter # 138 (SSI # 8Ah)
Select one of the following trigger modes for the digital scanner.
• Standard (Level)
- A trigger press activates decode processing. Decode processing continues until the
barcode decodes, you release the trigger, or the Decode Session Timeout on page 98 occurs.
• Presentation (Blink)
- The digital scanner activates decode processing when it detects a barcode in its field of view. After a period of non-use, the digital scanner enters a low power mode, in which the LEDs turn off until the digital scanner senses motion.
•
Auto Aim
- This trigger mode projects the aiming dot when you lift the digital scanner. A trigger press activates decode processing. After 5 seconds of inactivity the aiming dot shuts off.
87
* Level (Standard)
(0)
User Preferences
Presentation (Blink)
(7)
Auto Aim
(9)
88
User Preferences
Hands-Free Mode
Parameter # 630 (SSI # F1h 76h)
In hands-free mode, when you place the CS6080 in the presentation cradle, it automatically triggers when presented with a barcode. Lifting the digital scanner causes it to behave according to the setting of the
Hand-Held Trigger Mode on page 87
.
If you select
Disable Hands-Free Mode
, the digital scanner behaves according to the setting of the
Hand-Held Trigger Mode on page 87
regardless of whether the CS6080 is in the presentation cradle.
*
Enable Hands-Free Mode
(1)
Disable Hands-Free Mode
(0)
Hand-Held Decode Aiming Pattern
Parameter # 306 (SSI # F0h 32h)
Select
Enable
Hand-Held
Decode Aiming Pattern
to project the aiming dot during barcode capture,
Disable
Hand-Held
Decode Aiming Pattern
to turn the aiming dot off, or
Enable
Hand-Held
Decode
Aiming Pattern on PDF
to project the aiming dot when the digital scanner detects a 2D barcode.
NOTE:
With
enabled, the decode aiming dot flashes even when the
Hand-Held
Decode Aiming Pattern
is disabled.
89
User Preferences
*
Enable Hand-Held Decode Aiming Pattern
(2)
Disable Hand-Held Decode Aiming Pattern
(0)
Enable Hand-Held Decode Aiming Pattern on PDF
(3)
Hands-Free Decode Aiming Pattern
Parameter # 590 (SSI # F1h 4Eh)
Select
Enable Hands-Free Decode Aiming Pattern
to project the aiming dot during barcode capture,
Disable Hands-Free Decode Aiming Pattern
to turn the aiming dot off, or
Enable Hands-Free Decode
Aiming Pattern on PDF
to project the aiming dot when the digital scanner detects a 2D barcode.
NOTE:
With
enabled, the decode aiming dot flashes even when the
Decode
Aiming Pattern
is disabled.
90
User Preferences
Enable Hands-Free Decode Aiming Pattern
(1)
Enable Hands-Free Decode Aiming Pattern on PDF
(2)
* Disable Hands-Free Decode Aiming Pattern
(0)
91
User Preferences
Picklist Mode
Parameter # 402 (SSI # F0h 92h)
Scan one of the following barcodes to select a Picklist Mode. In this mode, you can pick out and decode a barcode from a group of barcodes that are printed close together by placing the aiming pattern on the barcode you want to decode.
NOTE:
Enabling Picklist Mode overrides the Disable Decode Aiming Pattern options. You can not disable the decode aiming pattern when Picklist Mode is enabled.
Enabling Picklist Mode can slow decode speed and hinder the ability to decode longer barcodes.
•
Enable Picklist Mode Always - Picklist Mode is always enabled.
•
Enable Picklist Mode in Hand-held Mode - Picklist Mode is enabled when the scanner is out of hands-free mode and disabled when the scanner is in presentation mode.
•
Enable Picklist Mode in Hands-free Mode - Picklist Mode is enabled when the scanner is in hands-free mode only.
•
Disable Picklist Mode Always - Picklist Mode is always disabled.
Enable Picklist Mode Always
(2)
Enable Picklist Mode in Hand-held Mode
(1)
Enable Picklist Mode in Hands-free Mode
(3)
* Disable Picklist Mode Always
(0)
92
User Preferences
Virtual Tether
Virtual tether is designed to alert users when a device is taken out of range. It includes an audible, visual
(includes the LEDs and illumination), and haptic alarm on the scanner if the Bluetooth connection is broken.
Virtual Tether Alarm Configuration
Parameter # 2053 (SSI # F8h 08h 05h)
Virtual tether alarm is disabled by default.
NOTE:
Disable Virtual Tether before performing a firmware update.
* Disable Virtual Tether Alarm
(0)
Enable Audio, Visual, and Haptic
Virtual Tether Alarm
(1)
Distance
To adjust the range of the scanner and cradle connection, see
Radio Output Power on page 135
.
Audio vs. Visual
If the scanner is in Night Mode (see
Night Mode on page 74 ), only the Visual alarm and Haptics activate.
The Audio beeper does not sound.
If the Virtual Tether is enabled (and Night Mode is disabled), then the audio alarm (beeper) always sounds at high volume.
93
User Preferences
Delay Before Virtual Alarm Activates
Parameter # 2054 (SSI # F8h 08h 06h)
When the device is out of range, it holds off on sounding the Virtual Tether alarm to provide an opportunity to re-establish a connection (5 - 99 seconds). The default is 30 seconds.
NOTE:
Ensure that this setting is not too short in order to avoid the following:
•
If the cradle resets, it causes the scanner to activate the Virtual Tether alarm.
•
Noisy RF environments can lead to frequent, momentary disconnect/reconnect sequences.
To set a timeout:
1.
Scan the
Delay Before Alarm Activates
barcode.
2.
Scan two barcodes from Numeric Barcodes that correspond to the desired timeout duration. Enter a
leading zero for single digit numbers (for example, for an alarm to start after 5 seconds, scan the 0 barcode and then the 5 barcode).
To correct an error or change the selection, scan Cancel on page 438
.
Delay Before Alarm Activates
Virtual Tether Alarm Duration
Parameter # 2055 (SSI # F8h 08h 07h)
Set up the amount of time for the Alarm to play in minutes (1 - 99 minutes). The default is 5 minutes.
To set a timeout:
1.
2.
Scan the
Alarm Duration
barcode.
Scan two barcodes from Numeric Barcodes that correspond to the desired alarm duration. Enter a
leading zero for single digit numbers (for example, for an alarm to start after 5 minutes, scan the 0 barcode and then the 5 barcode). The value of zero sets the duration to
Infinite
.
To correct an error or change the selection, scan Cancel on page 438
.
Alarm Duration
94
User Preferences
Stopping the Alarm
The alarm stops once the connection is established, the timeout period expires or the scanner’s battery is drained.
NOTE:
Any connection stops the alarm. The scanner does not need to connect to the same cradle.
Defeat Virtual Tether Alarm
Parameter # 2119 (SSI # F8h 08h 47h)
Pressing the Scan Button on the scanner can be configured to defeat or pause the alarm.
Continue Alarm on Scan Button
(0)
* Pause Alarm on Scan Button
(1)
Stop Alarm on Scan Button
(2)
Pause Virtual Tether Alarm Duration
Parameter # 2120 (SSI # F8h 08h 48h)
Pressing the Scan Button on the scanner pauses the alarm for a programmable number of seconds (1 - 99 seconds). The default is
30 Seconds
.
To set a timeout:
1.
Scan the
Pause Virtual Tether Alarm Duration
barcode.
95
User Preferences
2.
Scan two barcodes from Numeric Barcodes that correspond to the desired alarm duration. Enter a
leading zero for single digit numbers (for example, for an alarm to start after 5 seconds, scan the 0 barcode and then the 5 barcode).
To correct an error or change the selection, scan Cancel on page 438
.
Pause Virtual Tether Alarm Duration
Virtual Tether Alarm Considerations
Causes for the alarm to activate include:
•
The device goes out of range.
•
If the cradle does not have power, the scanner sounds an alarm. Includes USB suspend of the cradle.
•
The scanner enters Battery Preservation Mode and disconnects the battery.
•
If multiple cradles lose power during a power outage, scanners sound an alarm. To stop the alarm:
•
Unpower the scanners by removing the battery.
•
Connect the scanner to another device.
•
Press the Scan Button (must be configured to Stop Alarm on Scan Button)
Causes for the alarm to not activate:
•
The scanner and cradle need to have an existing connection before an alarm activates. No alarm on power up.
•
If the scanner is connected to another cradle/host by insertion or by scanning the pairing barcode.
•
If another scanner connects to the cradle and causes the original scanner to disconnect.
•
If any of the batch modes are enabled or if auto-reconnect is not set to reconnect immediately.
•
Virtual Tether does not apply to hosts that do not support the auto-reconnect feature such as HID
Bluetooth Low Energy (Discoverable) and SPP BT Classic (Discoverable).
96
User Preferences
Continuous Barcode Read
Parameter # 649 (SSI # F1h 89h)
Enable this to report every barcode while the trigger is pressed.
NOTE:
Zebra strongly recommends enabling
Picklist Mode on page 92 with this feature. Disabling Picklist
Mode can cause accidental decodes when more than one barcode is in the digital scanner's field of view.
*
Disable Continuous Barcode Read
(0)
Enable Continuous Barcode Read
(1)
Unique Barcode Reporting
Parameter # 723 (SSI # F1h D3h)
Enable this to report only unique barcodes while the trigger is pressed. This option only applies when
Continuous Barcode Read
is enabled.
Disable Continuous Barcode Read Uniqueness
(0)
97
*
Enable Continuous Barcode Read Uniqueness
(1)
User Preferences
Decode Session Timeout
Parameter # 136 (SSI # 88h)
This parameter sets the maximum time decode processing continues during a scan attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The default timeout is 9.9 seconds.
To set a Decode Session Timeout, scan the barcode below. Next, scan two numeric barcodes from
that correspond to the desired on time. Enter a leading zero for single digit numbers. For example, to set a Decode Session Timeout of 0.5 seconds, scan the barcode below, then scan the
0
and
5
barcodes. To correct an error or change the selection, scan Cancel on page 438 .
Decode Session Timeout
98
User Preferences
Hands-free Decode Session Timeout
Parameter # 400 (SSI # F0h 90h)
This parameter is the hands-free compliment to the
Decode Session Timeout
. It configures the minimum and maximum decode processing time during a hands-free scan attempt. It only applies to the hands-free trigger mode or when a scanner is placed in the Presentation cradle (CR6080-PC).
The minimum decode processing time is defined as the time in which the scanner stops decoding when an object is removed or left stationary in the imaging field of view.
The maximum decode processing time is defined as the time in which the scanner stops decoding when an object is left in and is moving in the field of view.
Both the maximum and minimum times are configured using a single setting. The relationship of this setting is as follows:
Setting Value
X < 25
X >= 25
Minimum Time
250 ms
X * 10 ms
Maximum Time
X * 100 ms
X * 100 ms
For example, a setting value of 100 results in the scanner turning off approximately 1 second after an object is removed from the field of view or 10 seconds while an object is in the field of view moving.
The default value of the setting is 15 which results in a Minimum time of 250 ms and Maximum time of 1.5 seconds.
Adjust this setting based on your requirements. For example, when doing PDF prioritization, this parameter should be set to a value where the maximum time is above the PDF prioritization timeout.
Hands-free Decode Session Timeout
99
User Preferences
Timeout Between Decodes, Same Symbol
Parameter # 137 (SSI # 89h)
Use this option in Continuous Barcode Read mode to prevent the beeper from continuously beeping when a symbol is left in the digital scanner field of view. The barcode must be out of the field of view for the timeout period before the digital scanner reads the same consecutive symbol. It is programmable in 0.1 second increments from 0.0 to 9.9 seconds. The default interval is 0.5 seconds.
To select the timeout between decodes for the same symbol, scan the barcode below, then scan two
numeric barcodes from Numeric Barcodes on page 438
that correspond to the desired interval, in 0.1 second increments.
Timeout Between Decodes, Same Symbol
Timeout Between Decodes, Different Symbols
Parameter # 144 (SSI # 90h)
Use this option in presentation mode or Continuous Barcode Read to control the time the digital scanner is inactive between decoding different symbols. It is programmable in 0.1 second increments from 0.1 to 9.9 seconds. The default is 0.1 seconds.
To select the timeout between decodes for different symbols, scan the barcode below, then scan two
numeric barcodes from Numeric Barcodes on page 438
that correspond to the desired interval, in 0.1 second increments.
NOTE:
Timeout Between Decodes, Different Symbols cannot be greater than or equal to the Decode
Session Timeout.
Timeout Between Decodes, Different Symbols
100
User Preferences
Triggered Timeout, Same Symbol
Parameter # 724 (SSI # F1 D4)
Scan
Enable Triggered Timeout, Same Symbol
below to apply
Timeout Between Decodes, Same
Symbol
(parameter #137 on page
100 ) in hand-held trigger mode. Subsequent scans of
Enable
Triggered Timeout, Same Symbol
are ignored until
Timeout Between Decodes, Same Symbol
expires.
NOTE:
1.This feature does not apply to Timeout Between Decodes, Different Symbols.
2.Timeout Between Decodes, Same Symbol should not be greater than or equal to the Time Delay
to Low Power Mode (parameter #146 on page 83 ).
Enable Triggered Timeout, Same Symbol
*
Disable Triggered Timeout, Same Symbol
101
User Preferences
Mobile Phone/Display Mode
Parameter # 716 (SSI # F1h CCh)
This mode improves barcode reading performance off mobile phones and electronic displays. Select
Enhanced in hand-held, hands-free, or both modes, or select Normal Mobile Phone/Display Mode.
*
Normal Mobile Phone/Display Mode
(0)
Enhanced in Hand-Held Mode
(1)
Enhanced in Hands-Free Mode
(2)
Enhanced in Both Modes
(3)
102
User Preferences
PDF Prioritization
Parameter # 719 (SSI # F1h CFh)
. During that time the digital scanner attempts to decode a PDF417 symbol (e.g., on a US driver's license), and if successful, reports this only. If it does not decode (can not find) a PDF417 symbol, it reports the 1D symbol after the timeout. The 1D symbol must be in the device field of view for the digital scanner to report it. This parameter does not affect decoding other symbologies.
NOTE:
The 1D Code 128 barcode lengths include the following:
•
7 to 10 characters
•
14 to 22 characters
•
27 to 28 characters
In addition, a Code 39 barcode with the following lengths are considered to potentially be part of a
US driver’s license:
•
8 characters
•
12 characters.
*
Disable PDF Prioritization
(0)
Enable PDF Prioritization
(1)
103
User Preferences
PDF Prioritization Timeout
Parameter # 720 (SSI # F1h D0h)
Hands-free Decode Session Timeout on page 98
should be set to a longer duration than Prioritization
Timeout when configured.
is enabled, this timeout specifies how long the digital scanner attempts to decode a PDF417 symbol before reporting the 1D barcode in the field of view.
Scan the following barcode, then scan four digits from
Numeric Barcodes on page 438 that specify the
timeout in milliseconds. For example, to enter 400 ms, scan the following barcode, then scan 0400. The range is 0 to 5000 ms, and the default is 200 ms.
PDF Prioritization Timeout
Decoding Illumination
Parameter # 298 (SSI # F0h 2Ah)
Selecting
Enable Decoding Illumination
causes the digital scanner to flash illumination to aid decoding.
Select
Disable Decoding Illumination
to prevent the digital scanner from using decoding illumination.
Enabling illumination usually results in superior images. The effectiveness of the illumination decreases as the distance to the target increases.
*
Enable Decoding Illumination
(1)
Disable Decoding Illumination
(0)
104
User Preferences
Illumination Brightness Hand-Held
Parameter # 669 (SSI # F1h 9Dh)
Scan one of the following barcodes to set the illumination brightness used during an active decode session. This only applies in hand-held mode (not in presentation mode).
NOTE:
Selecting a lower brightness level can affect decode performance.
Low Illumination Brightness for Hand-Held
(0)
Medium Illumination Brightness for Hand-Held
(3)
* High Illumination Brightness for Hand-Held
(8)
105
User Preferences
Illumination Brightness Hands-Free
Parameter # 2118 (SSI # F8h 08h 46h)
Scan one of the following barcodes to set the illumination brightness used when the scanner is in
Presentation Mode. This does not apply in hand-held mode.
NOTE:
Selecting a lower brightness level can affect decode performance.
Low Illumination Brightness for Hands-Free
(0)
* Medium Illumination Brightness for Hands-Free
(3)
High Illumination Brightness for Hands-Free
(7)
106
User Preferences
Low Light Scene Detection
Parameter # 810
SSI # F2h 2Ah
Scan one of the following barcodes to allow the scanner to detect motion in dim to dark illumination environments when in presentation mode:
• No Low Light Scene Detection
- The scanner attempts to detect motion as best it can with the aim pattern and illumination turned off when the scanner is idle.
• Aiming Pattern Low Light Assist Scene Detection
- Illumination is off, but the aim pattern is on when the scanner is idle to assist in scene detection.
• Dim Illumination Low Light Assist Scene Detection
- The aim pattern is off, but illumination is on at a dim level to assist in scene detection.
* No Low Light Assist Scene Detection
(0)
Aiming Pattern Low Light Assist Scene Detection
(1)
Dim Illumination Low Light Assist Scene Detection
(2)
107
User Preferences
Scene Detect Sensitivity
Parameter # 1943 (SSI # F8h 97h)
This parameter sets the illumination range sensitivity when motion is detected.
* Low
(10)
Medium
(128)
High
(190)
108
User Preferences
Motion Tolerance (Hand-Held Trigger Modes Only)
Parameter # 858 (SSI # F2h 5Ah)
Less Motion Tolerance
provides optimal decoding performance on 1D barcodes.
To increase motion tolerance and speed decoding when scanning a series of 1D barcodes in rapid progression, scan
More Motion Tolerance
.
* Less Motion Tolerance
(0)
More Motion Tolerance
(1)
109
User Preferences
Product ID (PID) Type
Parameter # 1281
SSI # F8h 05h 01h
Scan one of the following bar codes to define the PID value reported in USB enumeration.
* Host Type Unique
(0)
Product Unique
(1)
IBM Unique
(2)
Product ID (PID) Value
Parameter # 1725
SSI # F8h 06h BDh
To set a Product ID value, scan
Set PID Value
, and then scan four numeric bar codes in Numeric
NOTE:
This parameter is applicable to customers using a Firmware Flash Update per the Toshiba Global
Commerce Solutions (TGCS) Universal Serial Bus OEM Point-of-Sale Device Interface.
Set PID Value
110
User Preferences
ECLevel
Parameter # 1710
SSI # F8h 06h AEh
To set an ECLevel value, scan
Set ECLevel
, and then scan five numeric bar codes in
that correspond to the desired level. Enter a leading zero for single digit numbers. To correct an error, or change a selection, scan
NOTE:
This parameter is applicable to customers using a Firmware Flash Update per the Toshiba Global Commerce
Solutions (TGCS) Universal Serial Bus OEM Point-of-Sale Device Interface. It allows a customer to define an ECLevel value in order to manage and control Flash Update operations on the 4690 operating system.
Contact the Zebra Customer Support Center online at: www.zebra.com/support for more information.
Set ECLevel
Add an Enter Key
To add an Enter key (carriage return/line feed) after scanned data, scan the following barcode.
To program other prefixes and/or suffixes, see
Prefix/Suffix Values on page 112.
Add Enter Key (Carriage Return/Line Feed)
Transmit Code ID Character
Parameter # 45 (SSI # 2Dh)
A Code ID character identifies the code type of a scanned barcode. This is useful when decoding more than one code type. In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol.
Select no Code ID character, a Symbol Code ID character, or an AIM Code ID character. For Code ID characters, see
Programming Reference on page 417
.
NOTE:
If you enable Symbol Code ID Character or AIM Code ID Character, and enable Transmit “No
, the digital scanner appends the code ID for Code 39 to the NR message.
111
User Preferences
Transmit Code ID Character (continued)
Symbol Code ID Character
(2)
AIM Code ID Character
(1)
*
None
(0)
Prefix/Suffix Values
Key Category Parameter # P = 99, S1 = 98, S2 = 100 (SSI # P = 63h, S1 = 62h, S2
= 64h)
Decimal Value Parameter # P = 105, S1 = 104, S2 = 106 (SSI # P = 69h, S1 = 68h,
S2 = 6Ah)
You can append a prefix and/or one or two suffixes to scan data for use in data editing. To set a value for
a prefix or suffix, scan a four-digit number (i.e., four barcodes from Numeric Barcodes on page 438
) that corresponds to that value. See
ASCII Character Sets on page 457
for the four-digit codes.
When using host commands to set the prefix or suffix, set the key category parameter to 1, then set the
3-digit decimal value. See
ASCII Character Sets on page 457
for the four-digit codes.
The default prefix and suffix value is 7013 <CR><LF> (the Enter key). To correct an error or change a selection, scan
.
NOTE:
To use Prefix/Suffix values, first set the Scan Data Transmission Format on page 113
112
User Preferences
Scan Prefix
(7)
Scan Suffix 1
(6)
Scan Suffix 2
(8)
Data Format Cancel
Scan Data Transmission Format
Parameter # 235 (SSI # EBh)
To change the scan data format, scan one of the following eight barcodes corresponding to the desired format.
NOTE:
If using this parameter do not use ADF rules to set the prefix/suffix
.
113
User Preferences
To set values for the prefix and/or suffix, see Prefix/Suffix Values on page 112 .
*
Data As Is
(0)
<DATA> <SUFFIX 1>
(1)
<DATA> <SUFFIX 2>
(2)
<DATA> <SUFFIX 1> <SUFFIX 2>
(3)
<PREFIX> <DATA >
(4)
114
User Preferences
Scan Data Transmission Format (continued)
<PREFIX> <DATA> <SUFFIX 1>
(5)
<PREFIX> <DATA> <SUFFIX 2>
(6)
<PREFIX> <DATA> <SUFFIX 1> <SUFFIX 2>
(7)
FN1 Substitution Values
Key Category Parameter # 103 (SSI # 67h)
Decimal Value Parameter # 109 (SSI # 6Dh)
The wedge and USB HID keyboard hosts support a FN1 Substitution feature. Enabling this substitutes any
FN1 character (0x1b) in an EAN128 barcode with a value. This value defaults to 7013 (Enter Key).
When using host commands to set the FN1 substitution value, set the key category parameter to 1, then set the 3-digit keystroke value. See the ASCII Character Set table for the current host interface for the desired value.
To select a FN1 substitution value via barcode menus:
1.
Scan the barcode below.
Set FN1 Substitution Value
2.
Locate the keystroke desired for FN1 Substitution in the ASCII Character Set table for the current host interface. Enter the 4-digit ASCII Value by scanning each digit in
.
115
User Preferences
To correct an error or change the selection, scan
Cancel
.
To enable FN1 substitution for USB HID keyboard, scan the
Enable FN1 Substitution
barcode on page
.
Transmit “No Read” Message
Parameter # 94 (SSI # 5Eh)
Scan a barcode below to select whether or not to transmit a No Read message. Enable this to transmit the characters NR when a successful decode does not occur before trigger release or the
Decode Session
Timeout
expires. See Decode Session Timeout on page 98 . Disable this to send nothing to the host if a
symbol does not decode.
NOTE:
If you enable
Transmit No Read
, and also enable Symbol Code ID Character or AIM Code ID
Character for Transmit Code ID Character on page 111
, the digital scanner appends the code ID for Code
39 to the NR message.
Enable No Read
(1)
*
Disable No Read
(0)
116
User Preferences
Unsolicited Heartbeat Interval
Parameter # 1118 (SSI #
F8h 04h
5Eh)
The imager supports sending
Unsolicited Heartbeat Messages
to assist in diagnostics. To enable this feature and set the desired unsolicited heartbeat interval, scan one of the time interval barcodes below, or scan
Set Another Interval
followed by four numeric barcodes from Numeric Barcodes
(scan sequential numbers that correspond to the desired number of seconds).
Scan
Disable Unsolicited Heartbeat Interval
to turn off the feature.
The heartbeat event is sent as decode data (with no decode beep) in the form of:
MOTEVTHB:nnn where nnn is a three-digit sequence number starting at 001 and wrapping after 100.
10 seconds
(10)
1 minute
(60)
Set Another Interval
*
Disable Unsolicited Heartbeat Interval
(0)
117
User Preferences
securPharm Decoding
Parameter # 1752 (SSI #
F8h 06h D8h
)
securPharm decoding implements the IFA and GS1 Coding System for the European pharmaceutical industry. securPharm code is used to prevent pharmaceutical counterfeiting.
When this feature is enabled, if a GS1 symbol is decoded and includes any aspects of the Application
Identifier associated with the securPharm GS1 specifications, the entire GS1 symbol is processed as a securPharm symbol. For this reason, it is expected that under certain circumstances, a GS1 barcodes that is a securPharm symbol may not be processed properly; if the GS1 symbol is not created as per the specification. The output cannot be guaranteed as valid.
Although the GS1-128 type and the GS1 DataBar family are not specifically indicated in the IFA specification, they are supported.
The securPharm output is in XML format and can include the product number, serial number, lot number, expiration and Date of Manufacturing. The XML tags can be arranged in any order. Tags that are not in the barcode are omitted. For example:
<content dfi=”value_dfi”>
<Daten_1>value_Daten_1</Daten_1>
<Daten_2>value_Daten_2</Daten_2>
<Daten_n>value_Daten_n</Daten_n>
</content>
Where: value_dfi = IFA or GS1
Daten_1 to Daten_n is the production number, serial number, etc.
Scan a barcode below to enable or disable the ability to process pharmaceutical type barcodes.
*
Disable securPharm Decoding
(0)
Enable securPharm Decoding
(1)
118
User Preferences
securPharm Output Formatting
Parameter # 1753 (SSI #
F8h 06h D9h
)
NOTE:
securPharm Output Formatting is effective only when securPharm Decoding on page 118
is enabled.
securPharm Output Formatting parameter options represent bit positions. Therefore, any combination of formatting can be used.
When you scan a securPharm Output Formatting barcode, the securPharm output is formatted in a number of ways.
Sample GS1 Format
Product Number: GTINData Identifier DI Data Format Identifier: GS1
Data Carrier
FNC1
04150123456782
101A234B5
FNC1
1717231
211234567890123456
> Scanned Barcode >
<content dfi="GS1">
<gtin>04150123456782</gtin>
<lot>1A234B5</lot>
<exp>151231</exp>
<sn>1234567890123456</sn>
Sample GS1 Output - Feature Disabled
The output has no format:
0104150123456782101A234B517151231211234567890123456
Sample GS1 Output - No Formatting (0)
The output is a single line of characters:
<content dfi="GS1"><gtin>04150123456782</gtin><lot>1A234B5</lot><exp>151231</exp><sn>1234567890123
456</sn></content>
Sample GS1 Output - Insert Tab (1)
The output is a single line of characters with a tab inserted in the XML body:
<content dfi="GS1">
[tab]
<gtin>04150123456782</gtin>
[tab]
<lot>1A234B5</lot>
[tab]
<exp>151231</exp>
[tab]
<sn>123
4567890123456</sn></content>
Sample GS1 Output - Insert New Line (2)
The output consists of multiple lines of characters with a new line character at the end of each line.
<content dfi="GS1">
<gtin>04150123456782</gtin>
<lot>1A234B5</lot>
<exp>151231</exp>
<sn>1234567890123456</sn>
</content>
119
User Preferences
Sample GS1 Output - Insert Tab and New Line (3)
The output consists of multiple lines of characters with tabs and a new line character at the end of each line.
<content dfi="GS1">
[tab]
<gtin>04150123456782</gtin>
[tab]
<lot>1A234B5</lot>
[tab]
<exp>151231</exp>
[tab]
<sn>1234567890123456</sn>
</content>
Sample IFA Format
Product Number: PPNData Identifier DI Data Format Identifier: IFA
Data Carrier
Mac06
9N11123456782
Gs
1T1A234B5
Gs
D151231
Gs
S1234567890123456
> Scanned Barcode >
<content dfi="IFA">
<ppn>111234567842</ppn>
<lot>1A234B5</lot>
<sn>1234567890123456</sn>
</content>
Sample GS1 Output - Feature Disabled
The output has no format:
[)>069N1112345678421T1A234B5S1234567890123456
Sample GS1 Output - No Formatting (0)
The output is a single line of characters:
<content dfi="IFA"><ppn>111234567842</ppn><lot>1A234B5</lot><sn>1234567890123456</sn></content>
Sample GS1 Output - Insert Tab (1)
The output is a single line of characters with a tab inserted in the XML body:
<content dfi="IFA">
[tab]
<ppn>111234567842</ppn>
[tab]
<lot>1A234B5</lot>
[tab]
<sn>1234567890123456</sn></con tent>
Sample GS1 Output - Insert New Line (2)
The output consists of multiple lines of characters with a new line character at the end of each line.
<content dfi="IFA">
<ppn>111234567842</ppn>
<lot>1A234B5</lot>
<sn>1234567890123456</sn>
</content>
120
User Preferences
Sample GS1 Output - Insert Tab and New Line (3)
The output consists of multiple lines of characters with tabs and a new line character at the end of each line.
<content dfi="IFA">
[tab]
<ppn>111234567842</ppn>
[tab]
<lot>1A234B5</lot>
[tab]
<sn>1234567890123456</sn>
</content>
securPharm Output Formatting Barcodes
Scan a barcode below to format the securPharm output.
*
No Formatting
(0)
Insert Tab
(1)
Insert New Line
(2)
Insert Tab and New Line
(3)
121
User Preferences
Programmable Button for Single Press
Parameter # 2060 (SSI # F8h 08h 0Ch)
The Programmable Button can be configured for the following options:
• Apple Show/Hide Keypad
- If connecting to Apple devices in HID Keyboard Mode, a press of the
Programmable Button (-) shows or hides the keypad.
NOTE:
Apple features must be enabled for the show/hide keyboard feature to work (see Apple iOS Virtual
Keyboard Toggle on page 138 ).
• Second Trigger
- The Programmable Button (-) acts as a second trigger to scan parameters and decode data.
• Lamp Mode
- The Programmable Button (-) activates Lamp Mode (for more information, see
).
* Apple Show/Hide Keypad
(0)
Second Trigger
(1)
Lamp Mode
(2)
122
User Preferences
Programmable Button for Double Press
Parameter # 2103 (SSI # F8h 08h 37h)
The CS6080 can be programmed to drop the Bluetooth connection on a double press of the
Programmable Button.
NOTE:
The double press of the Scan Button issues Bluetooth connection to the last know device.
* No Action
(0)
Drop Bluetooth Connection
(1)
123
ಡೌನ್ಲೋಡ್ ಮಾಡಿ
ಸಾರ್ವಜನಿಕ ಲಿಂಕ್ ನವೀಕರಿಸಲಾಗಿದೆ
ನಿಮ್ಮ ಚಾಟ್ಗೆ ಸಾರ್ವಜನಿಕ ಲಿಂಕ್ ಅನ್ನು ನವೀಕರಿಸಲಾಗಿದೆ. You may view and manage your chat links after registration here.
ದಾಖಲೆಯ ಸಾರ್ವಜನಿಕ ಲಿಂಕ್
ಜಾಹಿರಾತು
