- Home
- Domestic appliances
- Large home appliances
- Water heaters & boilers
- TRIANGLE TUBE
- Prestige (PS)
- Installation and Maintenance Manual
advertisement
Unit Preparations
PRESTIGE Solo 60/175/250 Stud Walls -
Installation
1. Locate the studs in the general area of the boiler placement.
2. Place the wall-mounting bracket on the wall centering the mounting slots with the stud centers and ensuring the upper edge of the bracket is away from the wall.
3. Level the bracket, while maintaining it’s centering with the studs and use a pencil to mark the location of the mounting slots.
4. Remove the bracket from the wall and drill
1/4” diameter hole by 3” deep positioned in the center of each mark. For applications using metal studs and 3/16” toggle bolts, drill the required clearance hole.
5. Reposition the bracket onto the wall and align mounting slots/holes. Insert the two lag screws provided (or toggle bolts for metal studs) through the mounting slots/holes and loosely tighten.
6. Level bracket and tighten screws (bolts for metal studs) securely making sure not to over-tighten to avoid damaging drywall or plaster.
Wall Bracket Installation - Solid Walls
1. Locate the general area of the boiler placement.
2. Place the wall-mounting bracket on the wall ensuring the upper edge of the bracket is away from the wall.
3. Level the bracket and use a pencil to mark the location of the mounting slots on the wall.
4. Remove the bracket from the wall and drill a 5/8” diameter hole by 1-3/8” deep positioned in the center of each mark.
5. Install the anchors (provided) flush or slightly recessed in the drilled holes with threaded side facing down.
6. Reposition the bracket on the wall and align mounting slots/holes. Insert the two bolts (provided) through the mounting slots/holes and loosely tighten.
7. Level bracket and tighten bolts securely.
Boiler Mounting
1. Obtain assistance in lifting the boiler onto the wall bracket.
2. Install the boiler making sure the boiler mounting lip located along the upper edge of the rear jacket panel engages the wallmounting bracket. Ensure the boiler is seated properly and is secure.
PRESTIGE Solo 399 Stud Walls -
Installation
1. To distribute the weight of the boiler evenly when mounting onto a stud wall it is recommended to use the PRESTIGE Solo
Wall Frame kit.
2. When using the wall frame to mount the boiler reference the kit installation instructions and ensure the frame is securely fastened to the wall.
3. If the structure of wall is questionable, in supporting a minimum weight of 250 pounds [115 kg.], it is recommended to use the optional floor stand.
13
advertisement
Related manuals
advertisement
Table of contents
- 7 Definitions
- 8 Product and Safety Information
- 9 Code Compliance
- 9 Determining Product Location
- 9 Boiler Replacement
- 9 Recommended Clearances
- 10 Residential Garage Installations
- 10 Boiler Freeze Protection Feature
- 11 Combustion Air Contamination
- 12 Ventilation and Combustion Air Requirements - Direct Vent
- 12 Ventilation and Combustion Air Requirements - Category IV
- 13 Methods of Accessing Combustion Air into a Space - Category IV
- 13 - Indoor Combustion Air
- 13 - Outdoor Combustion Air
- 14 - Combination of Indoor and Outdoor Combustion Air
- 15 Combustion Air and Vent Piping
- 16 Removal of an Existing Boiler from a Common Vent System
- 17 Commonwealth of Massachusetts Installation
- 18 Handling Instructions
- 18 Wall Mounting Installation
- 18 Wall Mounting Guidelines
- 19 Wall Bracket Installation - Stud Walls
- 19 Wall Bracket Installation - Solid Walls
- 19 Boiler Mounting
- 20 General Piping Requirements
- 20 Pressure Relief Valve
- 20 Low Water Cut Off Device
- 22 Additional Limit Control
- 22 Backflow Preventer
- 22 Boiler System Piping Applications
- 22 Expansion Tank and Makeup Water
- 23 Diaphragm Expansion Tank
- 23 Closed-Type Expansion Tank
- 23 Circulator
- 23 Sizing Primary Piping
- 23 Domestic Hot Water System Piping
- 23 System Piping - Zone Circulators
- 24 Near Boiler Piping Diagrams
- 25 System Piping - Zone Valves
- 25 System Piping - Through Boiler
- 25 System Piping - Radiant Heating
- 25 System Piping - Special Applications
- 25 System Piping - Multiple Units Installation
- 26 DHW Boiler Piping with PRESTIGE Solo and SMART
- 27 Central Heating System Piping Diagrams
- 31 Installing Vent and Combustion Air
- 31 Installing Condensate Drain Assembly
- 33 Gas Supply Piping Connection
- 34 Pipe Sizing -Natural Gas
- 34 Natural Gas Supply Pressure Requirements
- 35 Pipe Sizing - Propane Gas
- 35 Propane Gas Supply Pressure Requirements
- 36 Gas Valve/Venturi Assembly
- 37 General Requirements
- 37 Control Module Circulator AMP Ratings
- 37 Wiring Tool Instructions
- 38 Internal Factory Wiring Diagram
- 39 Installation Compliance
- 39 Line Voltage Connections
- 39 Domestic Hot Water Aquastat Wiring
- 39 Thermostat Wiring
- 40 CH and DHW Circulator
- 40 System Circulator - Zone Valve Application
- 40 External Modulating Control
- 40 Outdoor Reset Control
- 40 Additional 24V Limit Wiring
- 40 External Wiring Diagrams
- 43 Water pH Level 6.0 to
- 43 Water Hardness Less Than 7 Grains
- 43 Chlorinated Water
- 43 Flush Boiler and Domestic System to Remove Sediment
- 43 Check and Test Antifreeze
- 44 Use of Antifreeze in the Boiler System
- 44 Filling the Boiler System
- 44 Check Low Water Cut-Off Device
- 45 Check for Gas Leaks
- 45 Check Thermostat Circuit
- 45 Inspection of Condensate Drain Assembly
- 46 Final Checks Before Start-Up
- 46 PRESTIGE Solo Start-Up
- 46 If PRESTIGE Solo Does Not Start Correctly
- 46 Check the PRESTIGE Solo and System
- 48 Operating Instructions
- 49 Set Boiler CH Target Temperature
- 49 Operation Verification - Space Heating
- 50 Operation Verification - Domestic Hot Water
- 51 Standby Mode
- 54 Parameter Mode
- 54 Information Mode
- 55 Error (Hard Lockout) Mode
- 56 Mounting the Outdoor Sensor
- 56 Wiring the Sensor
- 57 Summer/Winter Switch at Boiler
- 57 CH Maximum Boiler Operating Setpoint (Parameter 4)
- 57 CH Minimum Boiler Operating Setpoint (Parameter 10)
- 57 CH Reset Curve Coldest Day (Parameter 11)
- 58 CH Reset Curve Warmest Day (Parameter 12)
- 58 Entering MCBA Access Code
- 58 Changing a Parameter Setting
- 59 Outdoor Reset Curve Example
- 60 Wiring the Modulating Controller
- 60 Parameter Adjustment
- 60 Programming of External Modulating Control
- 61 Factory Setting for Parameters
- 62 Check-Out Procedures
- 63 Installation Record
- 64 Service Technician - General
- 64 Owner Maintenance
- 65 Reported Problems
- 65 Check Surrounding Area
- 65 Inspect Burner Area
- 65 Check System Piping
- 66 Clean Condensate Drain Assembly
- 66 Check Ventilation Air Openings
- 66 Inspect Vent and Combustion Air Piping
- 66 Check Boiler System
- 67 Check Expansion Tank
- 67 Check Boiler Relief Valve
- 67 Inspection of Ignition Electrode
- 67 Check Ignition Wiring and Ground Wiring
- 68 Check Control Wiring
- 68 Check Control Settings
- 68 Perform Start-Up and Checkout Procedure
- 68 Check Burner Flame
- 69 Check Flame Signal
- 69 Check Combustion Levels
- 69 Check Flue Gas Temperature
- 69 Clean Heat Exchanger
- 70 Review with Owner
- 70 Handling Previously Fired Combustion Chamber Insulation
- 71 Replacement Parts
- 78 Specifications