- Home
- Domestic appliances
- Large home appliances
- Water heaters & boilers
- TRIANGLE TUBE
- Prestige (PS)
- Installation and Maintenance Manual
advertisement
Maintenance Procedures
14. Attach a hose to the boiler drain valve and flush the boiler thoroughly with fresh water by using the purge valves to allow water to enter through the make-up water line to the boiler.
15. Once the boiler has been completely flushed, return the boiler and system piping back to operation.
16. Perform the required startup and checkout procedures as outlined on pages 37 to 57.
Review With Owner
Ensure the owner understands the importance to perform the maintenance schedule specified in this manual.
Remind the owner of the importance to call a licensed contractor should the unit or system exhibit any unusual behavior.
Handling Previously Fired Combustion Chamber Insulation
WARNING
The combustion chamber insulation contains ceramic fibers, which are classified as a possible human carcinogen.
When exposed to extremely high temperatures, the ceramic fibers, which contain crystalline silica, can be converted into cristobalite.
Avoid Breathing and Contact with Skin and Eyes
When removing or repairing the combustion chamber insulation follow these precaution measures:
1. Use a NIOSH approved respirator which meets OSHA requirements for cristobalite dust, similar to N95. Contact NIOSH at
1-800-356-4676 or on the web at www.cdc.gov/niosh for latest recommendations.
2. Wear long sleeved, loose fitting clothing, gloves and eyes protection.
3. Assure adequate ventilation.
4. Wash with soap and water after contact.
5. Wash potentially contaminated clothes separately from other laundry and rinse washing machine thoroughly.
6. Discard used insulation in an air tight plastic bag.
NIOSH Stated First Aid:
Eye/Skin: Immediately irrigate
Breathing: Clean fresh air
64
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Definitions
- 8 Product and Safety Information
- 9 Code Compliance
- 9 Determining Product Location
- 9 Boiler Replacement
- 9 Recommended Clearances
- 10 Residential Garage Installations
- 10 Boiler Freeze Protection Feature
- 11 Combustion Air Contamination
- 12 Ventilation and Combustion Air Requirements - Direct Vent
- 12 Ventilation and Combustion Air Requirements - Category IV
- 13 Methods of Accessing Combustion Air into a Space - Category IV
- 13 - Indoor Combustion Air
- 13 - Outdoor Combustion Air
- 14 - Combination of Indoor and Outdoor Combustion Air
- 15 Combustion Air and Vent Piping
- 16 Removal of an Existing Boiler from a Common Vent System
- 17 Commonwealth of Massachusetts Installation
- 18 Handling Instructions
- 18 Wall Mounting Installation
- 18 Wall Mounting Guidelines
- 19 Wall Bracket Installation - Stud Walls
- 19 Wall Bracket Installation - Solid Walls
- 19 Boiler Mounting
- 20 General Piping Requirements
- 20 Pressure Relief Valve
- 20 Low Water Cut Off Device
- 22 Additional Limit Control
- 22 Backflow Preventer
- 22 Boiler System Piping Applications
- 22 Expansion Tank and Makeup Water
- 23 Diaphragm Expansion Tank
- 23 Closed-Type Expansion Tank
- 23 Circulator
- 23 Sizing Primary Piping
- 23 Domestic Hot Water System Piping
- 23 System Piping - Zone Circulators
- 24 Near Boiler Piping Diagrams
- 25 System Piping - Zone Valves
- 25 System Piping - Through Boiler
- 25 System Piping - Radiant Heating
- 25 System Piping - Special Applications
- 25 System Piping - Multiple Units Installation
- 26 DHW Boiler Piping with PRESTIGE Solo and SMART
- 27 Central Heating System Piping Diagrams
- 31 Installing Vent and Combustion Air
- 31 Installing Condensate Drain Assembly
- 33 Gas Supply Piping Connection
- 34 Pipe Sizing -Natural Gas
- 34 Natural Gas Supply Pressure Requirements
- 35 Pipe Sizing - Propane Gas
- 35 Propane Gas Supply Pressure Requirements
- 36 Gas Valve/Venturi Assembly
- 37 General Requirements
- 37 Control Module Circulator AMP Ratings
- 37 Wiring Tool Instructions
- 38 Internal Factory Wiring Diagram
- 39 Installation Compliance
- 39 Line Voltage Connections
- 39 Domestic Hot Water Aquastat Wiring
- 39 Thermostat Wiring
- 40 CH and DHW Circulator
- 40 System Circulator - Zone Valve Application
- 40 External Modulating Control
- 40 Outdoor Reset Control
- 40 Additional 24V Limit Wiring
- 40 External Wiring Diagrams
- 43 Water pH Level 6.0 to
- 43 Water Hardness Less Than 7 Grains
- 43 Chlorinated Water
- 43 Flush Boiler and Domestic System to Remove Sediment
- 43 Check and Test Antifreeze
- 44 Use of Antifreeze in the Boiler System
- 44 Filling the Boiler System
- 44 Check Low Water Cut-Off Device
- 45 Check for Gas Leaks
- 45 Check Thermostat Circuit
- 45 Inspection of Condensate Drain Assembly
- 46 Final Checks Before Start-Up
- 46 PRESTIGE Solo Start-Up
- 46 If PRESTIGE Solo Does Not Start Correctly
- 46 Check the PRESTIGE Solo and System
- 48 Operating Instructions
- 49 Set Boiler CH Target Temperature
- 49 Operation Verification - Space Heating
- 50 Operation Verification - Domestic Hot Water
- 51 Standby Mode
- 54 Parameter Mode
- 54 Information Mode
- 55 Error (Hard Lockout) Mode
- 56 Mounting the Outdoor Sensor
- 56 Wiring the Sensor
- 57 Summer/Winter Switch at Boiler
- 57 CH Maximum Boiler Operating Setpoint (Parameter 4)
- 57 CH Minimum Boiler Operating Setpoint (Parameter 10)
- 57 CH Reset Curve Coldest Day (Parameter 11)
- 58 CH Reset Curve Warmest Day (Parameter 12)
- 58 Entering MCBA Access Code
- 58 Changing a Parameter Setting
- 59 Outdoor Reset Curve Example
- 60 Wiring the Modulating Controller
- 60 Parameter Adjustment
- 60 Programming of External Modulating Control
- 61 Factory Setting for Parameters
- 62 Check-Out Procedures
- 63 Installation Record
- 64 Service Technician - General
- 64 Owner Maintenance
- 65 Reported Problems
- 65 Check Surrounding Area
- 65 Inspect Burner Area
- 65 Check System Piping
- 66 Clean Condensate Drain Assembly
- 66 Check Ventilation Air Openings
- 66 Inspect Vent and Combustion Air Piping
- 66 Check Boiler System
- 67 Check Expansion Tank
- 67 Check Boiler Relief Valve
- 67 Inspection of Ignition Electrode
- 67 Check Ignition Wiring and Ground Wiring
- 68 Check Control Wiring
- 68 Check Control Settings
- 68 Perform Start-Up and Checkout Procedure
- 68 Check Burner Flame
- 69 Check Flame Signal
- 69 Check Combustion Levels
- 69 Check Flue Gas Temperature
- 69 Clean Heat Exchanger
- 70 Review with Owner
- 70 Handling Previously Fired Combustion Chamber Insulation
- 71 Replacement Parts
- 78 Specifications