advertisement
Introduction
Zoom, Focus, and Iris Control
Each PosiTrack unit delivers a low voltage pulse-width-modulated output for zoom, focus, and iris functions for motor mode lenses. These units are also capable of receiving reference voltage rails and sending zoom, focus, and iris control signals in response to these rails. In this setting (slideswitch configured), no active control signals will reach the lens before power (+ 12 VDC and
GND) is supplied to the lens. This motor mode applies to the control of the Fujinon and Canon teleconferencing lenses. During preset recall operation, these outputs are synchronized with the pan
and tilt motions. Refer to the PosiTrack Unit Lens Compatibility table on page 1. Four solid state
relays are also provided to control the zoom, focus, and iris speed/position mode selection and iris local/auto selection on the Fujinon MD series and Canon KTSA series lenses.
Sample Product Application
FIG. 2 shows a sample camera control application using the AXB-PT10.
Application #1 - AXlink
AXB-PT10
AXB-EM232
Enhanced Master
AXP-PLV
PSN6.5 Power
Supply
AXlink
Application #2 - RS-232
PS2.8
Power
Supply
AXB-PT10
RS-232
PSN6.5 Power
Supply
FIG. 2 Sample AXB-PT10 camera product application
Use a separate PSN6.5 power supply to power each PosiTrack unit. Power to the
PosiTrack unit is supplied from the PSN6.5 power supply to the unused power pin on the PosiTrack unit’s AXlink connector.
PC or other
RS-232 controller
4 AXB-PT10/30 PosiTrack Camera Controllers
advertisement
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 Specifications
- 7 Lens Control Modes
- 7 Servomotor Mode
- 7 Motor Mode
- 7 Pan and Tilt Control
- 8 Zoom, Focus, and Iris Control
- 8 Sample Product Application
- 9 Pre-Installation
- 9 Configuration Settings
- 10 Setting zoom, focus, and iris switches to servomotor or motor mode
- 10 Setting the RS-232 DIP switch (S2)
- 11 Setting the AXlink Device DIP switch (S5)
- 12 Accessing the AXB-PT10 Internal Jumpers
- 13 Accessing the AXB-PT30 Internal Jumpers
- 14 Setting the Internal Jumper Communication Mode
- 15 Configuring An External Camera/Lens Power Supply
- 17 Installation
- 17 Mounting the PT10 and PT
- 19 PT10 Camera/Lens Mounting and Balancing
- 21 PT30 Camera/Lens Mounting and Balancing
- 22 Wiring the Connectors
- 23 Wiring Guidelines
- 24 Preparing captive wires
- 24 Using the AXlink connector for data and power
- 25 Using the RS-232 DB-9 connector
- 26 Preparing the PosiTrack Controllers for communication
- 26 Using the lens control DB-15 HD (high density) connector
- 27 Pan Characteristics
- 27 Setting the adjustable pan-limit stops
- 28 Tilt Characteristics
- 28 Setting the adjustable tilt-limit stops
- 29 Programming
- 29 Configuration Commands
- 37 Channel Commands
- 37 Pan/tilt functions
- 38 Motor mode lens functions
- 38 Preset functions
- 40 Levels
- 40 Send_Commands
- 43 Diagnostic error values
- 44 Preset parameters and commands
- 46 RS-232 commands
- 48 RS-232 Send_Strings
- 48 Stand-Alone RS-232 Protocol
- 50 Response mask
- 51 Upgrading the Firmware
- 51 Configuration
- 51 Downloading the Firmware