advertisement
Pre-Installation
RS-232 control port fixed communications settings are: 9600 baud, No Parity, 8 bits, and 1 stop
bit. The following table lists the RS-232 Port DB-9 (male) pinouts.
RS-232 Port DB-9 (male) Pinouts
6
7
8
9
3
4
5
Pin
1
2
Signal
N/A
RXD
TXD
N/A
GND
N/A
RTS
CTS
N/A
Function
N/A
RXD
TXD
N/A
GND
N/A
RTS
CTS
N/A
The following table lists the RS-232 DIP switch settings.
RS-232 DIP Switch (S2) Settings
Position
Function
1 2
Stop Bits Data Bits
3
Off Off
2 bits
On
1 bit
Off
7 bits
On
8 bits
On
Off
On
Off
On
Off
On
4
Parity
Off
Unused
Off
Unused
On
Unused
On
Unused
Off
Unused
Off
Even
On
Odd
On
None
5
Off
Off
Off
Off
On
On
On
On
6
Off
On
Off
On
Off
On
Off
On
4,800
Off
9,600
On
19,200
On
38,400
7 8
Baud Rates
Off Off
300
Off Off
600
On
1,200
On
2,400
Off
Off
Off
On
On
On
On
Setting the AXlink Device DIP switch (S5)
The eight-position Device DIP switch (S5), shown in FIG. 5, must match the number assigned in
the Axcess software program. The Device DIP switch example is set to 90 (2 + 8 + 16 + 64 = 90), the factory default setting.
AXlink
DIP switch
(S5)
1 2 3 4 5 6 7 8
FIG. 5 AXlink device DIP switch (S5) (default value of 90)
AXB-PT10/30 PosiTrack Camera Controllers 7
advertisement
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 Specifications
- 7 Lens Control Modes
- 7 Servomotor Mode
- 7 Motor Mode
- 7 Pan and Tilt Control
- 8 Zoom, Focus, and Iris Control
- 8 Sample Product Application
- 9 Pre-Installation
- 9 Configuration Settings
- 10 Setting zoom, focus, and iris switches to servomotor or motor mode
- 10 Setting the RS-232 DIP switch (S2)
- 11 Setting the AXlink Device DIP switch (S5)
- 12 Accessing the AXB-PT10 Internal Jumpers
- 13 Accessing the AXB-PT30 Internal Jumpers
- 14 Setting the Internal Jumper Communication Mode
- 15 Configuring An External Camera/Lens Power Supply
- 17 Installation
- 17 Mounting the PT10 and PT
- 19 PT10 Camera/Lens Mounting and Balancing
- 21 PT30 Camera/Lens Mounting and Balancing
- 22 Wiring the Connectors
- 23 Wiring Guidelines
- 24 Preparing captive wires
- 24 Using the AXlink connector for data and power
- 25 Using the RS-232 DB-9 connector
- 26 Preparing the PosiTrack Controllers for communication
- 26 Using the lens control DB-15 HD (high density) connector
- 27 Pan Characteristics
- 27 Setting the adjustable pan-limit stops
- 28 Tilt Characteristics
- 28 Setting the adjustable tilt-limit stops
- 29 Programming
- 29 Configuration Commands
- 37 Channel Commands
- 37 Pan/tilt functions
- 38 Motor mode lens functions
- 38 Preset functions
- 40 Levels
- 40 Send_Commands
- 43 Diagnostic error values
- 44 Preset parameters and commands
- 46 RS-232 commands
- 48 RS-232 Send_Strings
- 48 Stand-Alone RS-232 Protocol
- 50 Response mask
- 51 Upgrading the Firmware
- 51 Configuration
- 51 Downloading the Firmware