advertisement
Installation
Lens Control DB-15 HD Connector Pinouts for Servomotor Mode
Pin
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
PosiTrack DB-15 HD connector functions
+12 VDC
GND
Zoom-drive
Focus-drive
Iris-drive
Zoom-speed/position
Focus-speed/position
Iris-local/auto
Iris-speed/position
VREF-A (+7.5V)
VREF-B (+2.5 V)
POT-REF+ (+5 VDC)
POT-REF- (GND)
Zoom-wiper (0-5 VDC)
Focus-wiper (0-5 VDC)
Direction
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Input
Output
Output
Input
Input
Lens function
Motor Power (see following note)
Lens common
Zoom motor
Focus motor
Iris motor
Zoom-positional/speed mode
Focus-positional/speed mode
Iris-local/auto select
Iris-positional/speed mode
VREF-A (+7.5 V). The reference voltage must be
present to operate correctly in servomotor mode.
VREF-B (+2.5 V). The reference voltage must be present to operate correctly in servomotor mode.
POT-high side
POT-low side
Zoom-POT wiper
Focus-POT wiper
Pin 1 is not required if the lens is powered independently. Pins 12-15 are required for
Speed mode but are not required for Positional mode.
This feature is controlled by the PANJA/CAM switch on the connector panel.
Servomotor driven outputs are intended to drive servo-type motors only. The outputs have very low current (milliampere range) capability. DO NOT attempt to drive conventional motors with these outputs or you may damage the output drivers. If you are not sure about the motor type, refer to the
Specifications section on page 1for more information.
Pan Characteristics
The pan drive has a maximum pan range of ± 174° (348° total). The maximum pan rate is 35° per second. Pan travel is capable of being limited to a restricted range around the center of pan travel by software limits adjustable by the programmer/end user. Pan limits refer to the horizontal range of motion available to the PosiTrack unit. These limits are set via the Axcess program. The center position marks the center of the range.
If you are using firmware version 1.01, do not set a preset at the same location as a limit stop.
Setting the adjustable pan-limit stops
The Central Controller should be programmed by an AMX Axcess programmer before beginning.
Refer to the Specifications section on page 1 for more information on programming devices. To set
the adjustable pan-limit stops:
AXB-PT10/30 PosiTrack Camera Controllers 23
advertisement
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 Specifications
- 7 Lens Control Modes
- 7 Servomotor Mode
- 7 Motor Mode
- 7 Pan and Tilt Control
- 8 Zoom, Focus, and Iris Control
- 8 Sample Product Application
- 9 Pre-Installation
- 9 Configuration Settings
- 10 Setting zoom, focus, and iris switches to servomotor or motor mode
- 10 Setting the RS-232 DIP switch (S2)
- 11 Setting the AXlink Device DIP switch (S5)
- 12 Accessing the AXB-PT10 Internal Jumpers
- 13 Accessing the AXB-PT30 Internal Jumpers
- 14 Setting the Internal Jumper Communication Mode
- 15 Configuring An External Camera/Lens Power Supply
- 17 Installation
- 17 Mounting the PT10 and PT
- 19 PT10 Camera/Lens Mounting and Balancing
- 21 PT30 Camera/Lens Mounting and Balancing
- 22 Wiring the Connectors
- 23 Wiring Guidelines
- 24 Preparing captive wires
- 24 Using the AXlink connector for data and power
- 25 Using the RS-232 DB-9 connector
- 26 Preparing the PosiTrack Controllers for communication
- 26 Using the lens control DB-15 HD (high density) connector
- 27 Pan Characteristics
- 27 Setting the adjustable pan-limit stops
- 28 Tilt Characteristics
- 28 Setting the adjustable tilt-limit stops
- 29 Programming
- 29 Configuration Commands
- 37 Channel Commands
- 37 Pan/tilt functions
- 38 Motor mode lens functions
- 38 Preset functions
- 40 Levels
- 40 Send_Commands
- 43 Diagnostic error values
- 44 Preset parameters and commands
- 46 RS-232 commands
- 48 RS-232 Send_Strings
- 48 Stand-Alone RS-232 Protocol
- 50 Response mask
- 51 Upgrading the Firmware
- 51 Configuration
- 51 Downloading the Firmware