Entering Data for Administrative Options. API Audio Accessories 1608-

Local Administrative Options

Entering Data for Administrative Options

This section applies to all 1600 Series IP Telephones and describes how to enter data for administrative options.

1. Invoke all local procedures by pressing the Mute button, up to 7 numeric dial pad buttons, and the # button.

A 6-second timeout is in effect between button presses after pressing the Mute button. If you do not press a valid button within 6 seconds of pressing the previous button, the collected digits are discarded. In this case, no administrative option is invoked.

2. Attempts to enter invalid data are rejected, and the telephone emits an error beep.

3. If you enter a numeric digit for a value or for an IP address or subnet mask field after entering only a zero, the new digit replaces the zero.

4. Press the # button to go to the next step.

5. To backspace, press the leftmost softkey. When you press the applicable button or key to backspace, the most recently entered digit or period is erased from the display. The cursor remains in the erased character’s former position.

6. If PROCPSWD is administered as indicated in Chapter 7 of the Avaya 1600 Series IP

Deskphones Administrator Guide, you must type the Local Procedure password after pressing Mute and before pressing the code for your given local programming option.

Note:

Note:

If PROCSTAT has been administered to 1, you will not be able to invoke any administrative options other than V I E W.

About Local Administrative Procedures

Local administrative procedures allow you to customize the 1600 Series IP Telephone installation for your specific operating environment. This section provides a description of each local administrative option covered in this guide, with references to the pages on which the option appears.

Note:

Note:

Unless otherwise prohibited by administration, the user can view but not change most of the parameters associated with Local Administrative procedures. For more information about this option, see the applicable user guides.

30 Avaya 1600 Series IP Deskphones Installation and Maintenance Guide

About Local Administrative Procedures

Local Programming Option Code See

Set 802.1X operational mode

Static addressing

Automatic Gain Control

DHCP chaddr field value

8 0 2 1 X (8 0 2 1 9)

Set the 802.1X Operational

Mode on page 32.

A D D R (2 3 3 7)

Static Addressing Installation on page 35 .

A G C (2 4 2)

Disable/Enable Automatic Gain

Control on page 38.

C H A D D R (2 4 2 3 3 7)

Manually Setting the DHCP

Client Hardware Address on page 40 .

Clear values to factory defaults C L E A R (2 5 3 2 7)

Enable/disable Debug Mode D E B U G (3 3 2 8 4)

Clear Procedure on page 41

Disable/Enable Debug Mode page 42.

.

on

Group Identifier

Interface Control

Event Logging

G R O U P (4 7 6 8 7)

I N T (4 6 8)

L O G (5 6 4)

Group Identifier on page 43

Disable/Enable Event

Logging on page 46.

.

Interface Control on page 44 .

Reset the telephone R E S E T (7 3 7 3 8)

Reset System Values on page 48 .

Restart the telephone R E S E T (7 3 7 3 8)

Restart the Telephone on page 49 .

Signaling protocol identifier

(not applicable to Release 1.0)

S I G (7 4 4)

Signaling Protocol Identifier on page 50 .

Site-Specific Option number S S O N (7 7 6 6)

Site-Specific Option Number

Setting on page 51.

Test the telephone

View current parameter values and file names

T E S T (8 3 7 8)

V I E W (8 4 3 9)

Self-Test Procedure on page 52

The View Administrative

Option on page 60.

.

Note:

Note:

Unless otherwise prohibited using administration, the user can view but not change most of the parameters associated with Local Administrative Procedures.

For more information about this option, see the applicable user guide(s).

Issue 4 February 2010 31