CONFIGURATION. ATCOM AT-320 IAX2, AT-323

AT-323 IAX2 Phone User Manual (V1.43)

3. Configuration

Four different ways can be used to configure AT-320 IP phone: phone keypad, web browser, Telnet commands and PalmTool configuration tool on computer.

3.1 Phone Keypad setup

3.1.1 Function Keys Introduction:

When using keypad and LCD to configure the settings of IP phone, following keys will be used:

Keys Function Keys Function

SET/LOCIP Enter setting mode OK/Speaker Enter submenu; confirm change

VOL+

Digital key

Turn over menu backward

Modify values

VOL-

EXIT/Redial

Turn over menu forward; move cursor backward

Exit current menu; exit setting mode

● Enter the keypad setting mode

Press “Speaker” key

Æenter “1234#”Æyou can see LCD display password” Æenter “1234”Æpress “speaker” key to confirm.

● Select the submenu

After entering the main menu, press “VOL+” or “VOL-” to page the menu up or page the menu down; when you want to set the submenu item to be displayed, press “OK/speaker” to enter the submenu.

● Enter the EDIT mode

After entering the submenu, when you want to set the submenu item to be selected, press “Set” to enter EDIT mode.

● Enter the settings

Once the phone enters EDIT mode, enter the settings by numeric keypad respectively, then press “OK/speaker” key to confirm.

● Modify enter error

If the errors come forth when you enter the settings, press“VOL-” key to delete it and enter the settings again

● Abort the settings

If there is no need for the modified settings, press “EXIT” key to return to the main menu, and press “VOL+” or “VOL-” to page the menu up or page the menu down; When “exit settings” submenu item is selected, press “OK/speaker” key to confirm, AT-320 IP phone will reboot and be used the current settings.

7

Keison Products www.keison.co.uk [email protected] Tel: +44 (0)1245 600560


● Save the settings

When all parameters have modified, press “EXIT” key to return to the main menu, and press “VOL+” or “VOL-” to page the menu up or page the menu down; When “save settings” submenu item is selected, press

“OK/speaker” key to confirm,AT-320 IP phone will reboot and use the already modified setting.

Refer to above operation; you can reach any menu to modify any value.

Please refer to following structure illustrations to learn the values of each menu item. As for the meaning of each item and value, please refer to Web

Browser Setting chapter.

8



¾ Menu Structure:

9



10



For example, you want to setup jack’s number 56712389 as speed dial number, you can:

Step Enter setup mode: press “Speaker” key Æenter “1234#”Æyou can see LCD display “password” Æenter “1234”Æpress “Speaker” key to confirm. dial setting” menu Æpress “speaker” enter its submenu and choose “memory

1” Æ press “Local IP” key and enter “jack” to modifyÆ press “Speaker” to confirm Æchoose “number 1”Æpress “Local IP” key and enter “56712389” to modify

Æ press “Speaker” to confirm. menu Æchoose “save setting”Æ press “Speaker” to confirm the change.

11



3.2 Configured by WEB

Double click icon to open the IE browser. Input the IP address of the phone into address bar ( ), and then input password of the phone into the following page. Default password 1234 is ordinary password and super password is 12345678. With Debug set 0[disable], please input super password; while Debug is not set as 0[disable], please input ordinary password. Then click button. The following configured page wills pop up. Refer to Fig 3.1 please.

Fig 3.1 Http Setting

12



Fig 3.2 Network Setting

● IPtype: Set how IP phone gets relevant network parameters by selecting corresponding item from drop down list.

static IP: Select this item to authorize users set IP address, subnet mask and router IP address of IP phone manually.

dhcp: Select this item to enable DHCP mode. With this system, your

LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on. AT-320 IP phone is shIPped from the factory with DHCP on. So, if your LAN or router is configured to use DHCP addressing, the IP phone’s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up.

PPPoE Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them. With this system, ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on.

modem If the IP phone used with modem, please select this item to get relevant network parameters auto. Then please fill ID and pin into ppp id and ppp pin fields.

● ppp id: With PPPoE or modem selected in IPtype drop down list, please enter the user name here.

● ppp pin: With PPPoE or modem selected in IPtype drop down list, please enter the password here.

● local IP: With static IP selected in IPtype drop down list, please enter IP address of IP phone here.

● subnet mask: With static IP selected in IPtype drop down list, please enter subnet mask of IP phone here.

● router IP: With static IP selected in IPtype drop down list, please enter router IP address of IP phone here.

13



● dns: With static IP selected in IPtype drop down list, please enter IP address of DNS server here.

● dns 2: With static IP selected in IPtype drop down list, please enter IP address of backup DNS server here.

● mac: MAC address is the physical address supplied by the Ethernet

NIC. AT-320 phone is shIPped from the factory with a unique algorism

MAC address printed on the back of the base.

Note To avoid colliding with other device in network, please don’t change the MAC address arbitrarily. If you have use “* and power on twice” method to enter the safe mode of your phone, remember to change the phone’s MAC to factory default after safe mode.

Fig 3.3 Audio Setting

● codec1: Set the priority 1 of the audio compression algorithm. The options are g729 g7231 g711u g711a , gsm and iLBC.






14



● vad: Enable/disable VAD (voice activity detection).

● agc: Enable/disable AGC.

● aec: Enable/disable AEC.

● g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is

6.3kbps, low rate is 5.3kbps.

● audio frame: Set audio frames in RTP package. Minimum is 1 and maximum is 8.

● jitter size : Set buffer size of RTP package. The value range is 0-32.

● ilbc payload : Set the payload type of RTP package when ILBC codec selected to DTMF delay. The value range is 96-255.

● handset in: Drag the slider to adjust the volume of handset input. Drag it to the left to reduce the volume; while drag it to the right to increase the volume.

● handset out: Drag the slider to adjust the volume of handset output. Drag it to the left to reduce the volume; while drag it to the right to increase the volume.

● ring type: Set ring type by selecting corresponding item from drop down list.

dtmf: Set ring as ordinary rings in different frequency

not disturb: Set the phone do not ring by selecting this item.

Advanced: Set ring used the individualized tone provided by system

(need system support).

user define Set ring as music saved by user by selecting this item.

● speaker in: Set the volume of handfree input.

● speaker out: Set the volume of handfree output.

15



3.2.3 Dial plan Setting

Fig 3.4 Dial Plan Setting

● use dialplan: Set whether use dial plan or use dial number by selecting the corresponding item in drop down list.

disable: Do not use dial plan or dial number by selecting this item.

enable: Use dial plan by selecting this item.

dialnum: Use dial number by selecting this item. With this item

selected, please enter the dial prefix into dial number field.

prefix: Use specially service by selecting this item.

Hotline: Use Hotline function by selecting this item. With this item selected, please enter the hotline number into dial number field.

● dial number: With dialnum selected in use dialplan drop down list, please enter the dial prefix into this field according to requirement of log in server. For example, with eTalk card used, enter 00 here.

● ddd code: With enable or dialnum selected in use dialplan drop down list, set area code according to E.164 dial rule. For example, Beiing 10;

Shanghai 21.

● idd code: With enable or dialnum selected in use dialplan drop down list, set country code according to E.164 dial rule. For example, China 86;

U.S.A .1.

● idd prefix: With enable or dialnum selected in use dialplan drop down list, set international call prefix according to E.164 dial rule, such as 00.

● ddd prefix: With enable or dialnum selected in use dialplan drop down list, set long distance call prefix according to E.164 dial rule, such as

0.

Note With dialnum seletcted in use dialplan drop down list, you can also set dddcode, iddcode, iddprefix and dddprefix according to requirement of system.

● innerline: Enable/disable multi-settings by selecting corresponding items from dropdown list. AT-320 IP phone allows saving 5 settings totally.

disable: Disable multi-settings by selecting this item, then the phone

16


AT-323 IAX2 Phone User Manual (V1.43) will call out using current setting.

enable: Use designated system to place calls by selecting this item.

innerlineprefix: With enable selected in innerline dropdown list, please fill the prefix number pick up to inner line, such as 0.

● Use digitmap: Enable/disable digit map by checking/unchecking the box.

● Call waiting: Enable/disable call waiting by checking/unchecking the box.

● forward number: Enter receiving forwarded calls phone number into this field; If the IP phone used with modem, with modem item selected in

IPtype list box, and then fill ISP number into this field.

● fwd poweroff: Forward calls if power off by checking this box. Please enter receiving forwarded calls phone number into fwd number field.

● fwd noanswer: Forward calls without replying by checking this box.

Please enter receiving forwarded calls phone number into fwd number field.

● fwd always: Forward all calls by checking this box. Please enter receiving forwarded calls phone number into fwd number field.

● fwd busy: Forward calls if busy by checking this box. Please enter receiving forwarded calls phone number into fwd number field.

● answer: Enter a number from 0 through 60 to set the entries of the seconds before the phone answer the call auto or forward the calls.

Note please refer to FAQ for more information of dial plan

17



3.2.4 IAX2 Protocol Settings

Fig 3.5 IAX2 Protocol Settings

● service addr: Please set the URI (domain name/IP address : service port) of the asterisk server into “service addr”. When the default service port

4569 is used, “: service port” can be omitted.

● register ttl : IP phone will send a keep-alive registration message to theasterisk server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60.

● phone number: The local phone number or username of this phone, usually is allocated by system.

● account: With the asterisk server which requires authentication, please put the username/account into this field.

● pin: With the asterisk server which requires authentication, please put the password into this field.

● local port: The local UDP port registered with the asterisk server to accept incoming handshaking messages. The default port number is

4569.

● dtmf: Set DTMF signal sending way by selecting inband audio, outband audio from list box.

● tos: Set the TOS field of the IP header of the RTP packets. The bigger this value is 0, the higher priority the packet is .

● super password: Set the super password of the phone.(Default super password is 12345678).

● debug: Set the debug level of the phone.

disable: Disable output the debug message by selecting this item.

output: Output the operation information to the window, such as register, input by selecting this item.

output all: Output all debug information and data in test window by selecting this item.

remote debug: Save the debug information in SDRAM of IP phone by

18



selecting this item.

no check: Disable checking firmware tags when upgrading. This is not suggested, because it will increase the risk of upgrading the wrong firmware into the phone.

Fig 3.6 Other Setting Page

● password: Set the password of the phone. (Default password is 1234).

● upgradetype: Set the auto-upgrade type of the phone.

disable : Disable auto-upgrade .

all: AT320 will find matching firmware binary file and configuration file of the hardware type only at the FTP server specify by upgradeaddr item .

mac: AT320 phone will find matching firmware binary file and configuration file of the MAC address only at the FTP server specify by

upgradeaddr item .

ppp id: AT320 phone will find matching firmware binary file and configuration file of the ppp id only at the FTP server specify by upgradeaddr item .

account: AT320 phone will find matching firmware binary file and configuration file of the account only at the FTP server specify by upgradeaddr item .

phonenumber: AT320 phone will find matching firmware binary file and configuration file of the phone only at the FTP server specify by upgradeaddr item .

● upgrade addr: Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field.

● sntp IP: Fill IP address of time server here. When network without

Internet connect, Fill special IP address 255.255.255.255.

● use daylight: Enable/disable daylight.

● timezone: Select correct time zone in list box.

When debug set as 0[disable], if input ordinary password (default one is 1234), then following page will pop up after clicking . And only those

19


AT-323 IAX2 Phone User Manual (V1.43) parameters can be modified.

Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable]

● Save Settings : Click this button to save the configuration and the phone will reboot. Once the phone reboots successfully, the new configuration is effective.

Note After entering set page, if save settings button is not clicked within 10 minutes, then when you click it again, the index page asking for pin will pop up again. Then please input the password again to enter the set page and then click save settings button to confirm the modification.

● Address Book: Click this button to open the speed dial settings page.

Please refer to Fig 3.8. In this page, you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name. For example, input Jack in

Name field following 001, and then input 5989426454 into Phone

number field. Then Jack’s number 5989426454 is saved in phone book.

Then please click Save/Back button. In normal state, you can use speed dial to call numbers saved in phone book.

20



Fig 3.8 Phone Book Illustration

● Upgrade Firmware: Click this button to update the program, the ring and the digit map of IP phone.

Fig 3.9 Upgrade firmware Illustration

21



3.3 Configured by PalmTool

PalmTool is a tool designed especially to configure and upgrade the AT-320 IP phone. On a PC double click icon to open the PalmTool. The index page of

PalmTool will popup.

Input the IP address of the phone into Local IP field (such as 192.168.1.100), and then click “Phone Settings” button.

Use PalmTool to set the IP phone, please set debug as output or output all firstly, otherwise PalmTool cannot connect IP phone. The parameters of

PalmTool is same as the parameters in HTTP, so please refer to HTTP set chapter to learn how to set IP phone.

22



3.4 Telnet Configuration

● On the PC choose Start>Run, and then type telnet 192.168.1.100 into

Run field in popuping Run dialog. Or input telnet 192.168.1.100 in the

DOS window. Then the following information will be displayed.

PA168X V1.43 settings

Password :

Then please type password. With debug is set as 0[disable], if type ordinary password (default one is 1234), after Retun, you will see

Password : ****

P:\>

If you type super password, then you will see:

Password : ********

P:\>

Above information indicates that IP phone is under setting mode, and then you can set the AT-320 IP phone by using the telnet commands.

3.4.1 AT-320 Telnet Commands Explanation

AT-320 Telnet Commands

Command Function

? Supply command name and parameters get set

Display basic parameters of AT-320 IP phone

Set parameters of AT-320 IP phone

Save current settings to designated position store load exit

Load designated settings to current position

Exit from the setting mode without saving the configuration write ping

Exit with saving all configurations and restart AT-320

Ping other net parameter ftp The phone connects to FTP server and then get the files

Detail descrIPtion of AT-320 Telnet commands

¾ Command ?

Syntax descrIPtion: No optional parameter

Usage: Type command name and parameters following P:\> . Be used as the keyword to supply keyword and parameters of the relevant commands.

23



Relevant usage: None

Detailed descrIPtion:

List help of all commands

For example:

P:\>? set get list settings store x store current to xth settings load x load xth settings to current exit write save settings

¾ Command get

Syntax descrIPtion: No optional parameter of keywords

Usage: Display basic parameters of AT-320 IP phone


Detailed descrIPtion:

get Display basic running parameters of the AT-320 IP phone. Input ordinary password without debug being set as 0[disable], or input super password with debug set as 0[disable], then following parameters of IP phone will be displayed:


Password: ********

P:\>get

***************Network Settings***************

IPtype 0[static]

IP 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254 dns 202.106.196.152 dns 2202.106.196.115 mac 00-09-45-65-a3-e6

***************Audio Settings*************** codec1 0[g729] codec2 1[g7231] codec3 2[g711u] codec4 3[g711a] codec5 6[null] codec6 6[null] vad 1[enable] agc 0[disable] aec 1[enable] audioframes 2 6.3k 1[enable] ilbcpayload 98 jittersize 0 handsetin 7 handsetout 20 ringtype 0[dtmf] speakerout 20 speakerin 0

***************Dial Plan Settings*************** dialplan 1[enable] dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1[enable] innerlineprefix 0 callwaiting 1[disable]

24


AT-323 IAX2 Phone User Manual (V1.43) fwdnumber 82378009 fwdpoweroff 1[enable] fwdalways 1[enable] fwdbusy 1[enable] fwdnoanswer 1[enable] answer 30 digitmap 1[enable]

***************Protocol Settings*************** serviceaddr 203.93.9.57 registerttl 60 phonenumber 82378808 account [empty] pin [empty] localport 1720 dtmf 1[outband signal] tos 0

***************Other Settings*************** superpassword 12345678 debug 1[output] password 1234 upgradetype 0[disable] upgradeaddr [empty] sntpIP 0.0.0.0 daylight 0[disable] timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

Input ordinary password with debug set as 0[disable], following information will be seen:


Password:****

P:\>get

***************Network Settings***************

IPtype 0[static]

IP 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254 dns 202.106.46.151 dns2 202.96.128.68 mac 00-0d-ea-00-00-03

***************Audio Settings*************** codec1 0[g729] codec2 1[g7231] codec3 2[g711u] codec4 3[g711a] codec5 6[null] codec6 6[null] vad 1[enable] agc 0[disable] aec 1[enable] audioframes 2 6.3k 1[enable] ilbcpayload 98 jittersize 0 handsetin 7 handsetout 20 ringtype 0[dtmf] speakerout 20 speakerin 0

***************Dial Plan Settings*************** dialplan 1[enable] dddcode 10 iddcode 86 iddprefix 00 dddprefix 0 innerline 1[enable] innerlineprefix 0 callwaiting 1[disable] fwdnumber 82378009 fwdpoweroff 1[enable] fwdalways 1[enable] fwdbusy 1[enable] fwdnoanswer 1[enable] answer 30 digitmap 1[enable]

***************Other Settings*************** password 1234 upgradetype 0[disable] upgradeaddr [empty] sntpIP 0.0.0.0 daylight 0[disable] timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

25



¾ Command set

Syntax descrIPtion: set keywords value

Usage: Used to configure password and other running parameters of

AT-320 IP phone.

Detailed descrIPtion: set IPtype X

Set how IP phone gets relevant network parameters. X ranged from 0 through 3: 0: authorize users set IP address, subnet mask and router

IP address of IP phone manually; 1: use DHCP mode. With this system, your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on. AT-320 IP phone is shIPped from the factory with DHCP on. So, if your LAN or router is configured to use DHCP addressing, the IP phone’s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up; 2: use PPPoE mode. Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them. With this system,

ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on; 3: use modem mode.

Those who use IP phone with modem, please set the value as 3. set pppid XXX

With IPtype set as 2, use this command to set ADSL ID; with IPtype set as 3, use this command to set Modem ID. set ppppin XXX

With IPtype set as 2, use this command to set ADSL pin; with IPtype set as 3, use this command to set Modem pin. set IP XXX.XXX.XXX.XXX

With IPtype set as 0, use this command to set IP address of AT-320

IP phone. set subnetmask XXX.XXX.XXX.XXX

With IPtype set as 0, use this command to set subnet mask of

AT-320 IP phone. set router XXX.XXX.XXX.XXX

With IPtype set as 0, use this command to set router IP of network with AT-320 IP phone. set dns XXX.XXX.XXX.XXX

With IPtype set as 0, use this command to set IP address of DNS server. set dns2 XXX.XXX.XXX.XXX

With IPtype set as 0, use this command to set IP of backup DNS server. set mac XX-XX-XX-XX-XX-XX

Set MAC address of the AT-320 IP phone. Parameter xx-xx-xx-xx-xx-xx must be an HEX number.

26



set codec1 X

Set the priority 1of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec2 X

Set the priority 2 of the audio compression algorithm. X is range from 0 through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec3 X


set codec4 X


set codec5 X


set codec6 X


set vad X

Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD; 1: enable VAD.

set agc X

Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC; 1: enable AGC.

set aec X

Enable/disable AEC. X is ranged from 0 through 1: 0: disable AEC; 1: disable AEC.

set audioframes X

Set audio frames in RTP package. X is Arabic numerals between 0 and 7.

set 6.3k X

With G.7231, set AT320 IP phone to use 6.3K rate or not. X is ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate.

set jittersize X

Set buffer size of RTP package. X is range from 0-32.

set ilbcpayload X

Set the payload type of RTP package whne ILBC codec selected to

DTMF delay.X is range from 96-255.

set handsetin X

Set initial volume of handset. X is ranged from 0 through 15.

set handsetout X

Set initial volume of handout. X is ranged from 0 through 31.

set ringtype X

Set types of ring. X is ranged from 0 through 3: 0: ring as ordinary

27


AT-323 IAX2 Phone User Manual (V1.43) rings in different frequency; 1: do not ring; 2: ring as music saved by user; 3: Set ring used the individualized tone provided by system

(need system support).

set speakerin X

Set initial volume of microphone of the base. X is ranged from 0 through 15.

set speakerout X

Set initial volume of speaker out. X is ranged from 0 through 31.

set dialplan X

Enable/disable dial plan and dial number. Parameter X ranged from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number;

3: use 179XX service.;4: use hotline function.

set dialnumber XX

When set dialplan value set as 2, please use this command to set dial number. For example, with eTalk card used, please set it as 00.

When set dialplan value set as 4, please use this command to set hotline number.

set dddcode XX

Set the area code when set dialplan value set as 1 or 2. For example, the area code of Beijing is 10; the area code of Shanghai is 21, and the area code of Chengdu is 28, etc. Parameter xxx must be an Arabic numeral and no longer than 3 characters.

set iddcode XXX

Set the country code when set dialplan value set as 1 or 2. For example, the country code of China is 86; the country code of USA is 1, etc. Parameter xxxx must be an Arabic numeral and no longer than 4 characters.

set iddprefix XX

Set IDD service prefix number when set dialplan value set as 1 or 2.

For example, IDD service prefix number of china is 00; IDD service prefix number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer than 3 characters.

set dddprefix XX

Set DDD service prefix number when set dialplan value set as 1 or 2.

For example, DDD service prefix number of china is 0; DDD service prefix number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer than 3 characters.

set innerline X

Set use innerline call or not. X ranged from 0 through 1: 0: disable; 1: enable innerline call.

set innerlinepreifx X

With innerline set as 1[enable] , please set the prefix to pick up inner line, such as 0.

28



set callwait X

Set whether to use call wait. X ranged from 0 to 1: 0: do not use call wait; 1: use call wait.

set fwdnumber XXXXXXX

Set receiving forwarded calls phone number. XXXX must be an Arabic numeral and no longer than 16 characters

set fwdalways X

Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not forward all calls; 1: forward all calls.

set fwdbusy X

Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not forward calls if busy; 1: forward call if busy.

set fwdnoanswer X

Enable/disable forward calls without replying. X is ranged from 0 through 1. 0: do not forward calls without replying; 1: forward call without replying.

set answer X

Set the ring seconds before the phone answers the call auto or forward the calls. X is ranged from 0 through 60.

set digitmap X

Set whether to use digitmap. X ranged from 0 to 1: 0: do not use digitmap; 1: use digitmap. set serviceaddr XXXX

Set IP address or domain name of asterisk server. set registerttl X

Set register TTL. X is range from 10 through 65535 Sec. Default value is 60 Sec. set phonenumber XXXXXXXX

Set a local ID of AT-320 IP Phone. Value xxxxx must be an Arabic numeral and no longer than 16 characters. set account XXXXXX

Set the account; Value xxxxxx must be an Arabic numeral and no longer than 32 characters. set pin XXXXXXXXXX

Set the account; Value xxxxxx must be an Arabic numeral and no longer than 32 characters. set localport XXXX

Set the local port. Value XXXX default is 4569. set dtmf X

Set DTMF relay type. X is ranged form 0 through 1: 0: Inband audio

1: outband audio.

set tos X

Set TOS segment of IP head package in RTP digital follow. X is range

29


AT-323 IAX2 Phone User Manual (V1.43) from 0 through 224.

set superpassword XXXX

Set super password of the AT320 IP phone. XXX must be ASCII characters.

set debug X

Set open debugging message output grade for special tool. X is ranged from 0 through 5: 0: close debugging output; 1: output the operation information to the window; 2: output all the bug information and data in test window; 3: save the bug information into SDRAM; 4: disable checks the mark.

set password XXXX

Set password of the AT-320 IP phone. XXX must be ASCII characters.

set upgradetype X

Set auto-upgrade matching type X is range from 0 through 5

0------disable 1------all 2------ mac 3------ppp id; 4------ account;

5------ phone number

set upgradeaddr XXX.XXX.XXX.XXX

Set IP address or domain name of FTP server supplying upgraded program of AT-320 IP phone.

set sntpIP XXX.XXX.XXX.XXX

Set IP address of time server.

set daylight X

Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight; 1: use daylight.

set timezone XX

Set time zone.

¾

Command store

Syntax descrIPtion: no keyword. Parameter ranged from 0 through 4.

Usage: Save the current settings to the designated position.

Relevant Usage: store 1

¾

Command load

Syntax descrIPtion: no keyword. Parameter ranged from 0 through 4.

Usage: Load the designated settings to the current position.

Relevant Usage: load 1

¾ Command exit

Syntax descrIPtion: no keyword and parameter

Usage: Exit from Telnet command window without saving the configuration.

30




¾ Command write

Syntax descrIPtion: No keyword and parameter

Usage: Save the configuration and restart the AT-320 IP phone.

¾ Command ping

Syntax descrIPtion: ping IP address

Usage: ping IP address of other NAT device

Relevant usage: In telnet window, input ping xx.xxx.xx.xx an IP address and return, then the result will be displayed. If the address is effective, “ping OK” will be seen; if the address is ineffective, nothing will be seen. Fox example:

P:\>ping 203.93.9.57

P:\> ping OK

P:\>ping 27.56.120.56

P:\>

Note Usually, the echo time of ping command is no more than 1 second. So if the result is not displayed in 5 seconds, ping command is fail.

¾ Command ftp

Syntax descrIPtion: ftp value

Usage: the system connects to the FTP server auto to get the corresponding file and deal with it.

Relevant usage: ftp X

X ranged from 0 through 2:

X-0: Connect to FTP Server to get the file of updating program and save it to the SDRAM of the phone. Then the file can be read by PalmTool.

This operation aims at testing.

X-1: Connect to FTP Server to get the file of updating program and update program Flash. This operation aims at updating program.

X-2: Connect to FTP Server to get the file of updating dial rules and update program Flash. This operation aims at updating dial rule.

Note When you use ftp 0 and ftp 1 commands, if the file get from FTP server is too large or the net speed is too slow, then the process will not be seen in telnet window.

31



Please be patient. Using ftp command in telnet to get file spends almost same minutes as getting file using phone. So if nothing is displayed after too long time, it means that ftp is fail.

Note All the Telnet commands of AT-320 IP phone should be written in low case and the password is case sensitive.

32


CONFIGURATION. ATCOM AT-320 IAX2, AT-323

3. Configuration

Related manuals

Table of contents

CONFIGURATION. ATCOM AT-320 IAX2, AT-323

3. Configuration

Related manuals

ServComp

500

Perfectone Net Ware

GW-200

Yoda

VP200

UTStarcom

F1000 Series

PalmMicro

PA168X

Centrality

PA168X IAX2

Table of contents