Check for Queue and Imposition Files. Xerox 490
Add to My manualsadvertisement
![Check for Queue and Imposition Files. Xerox 490 | Manualzz Check for Queue and Imposition Files. Xerox 490 | Manualzz](http://s1.manualzz.com/store/data/002112658_1-334133b98dfdda4d87bd503b330e5792-360x466.png)
Xerox 490/980 Color Continuous Feed Printing System Prepare for Color Calibration
Check for Queue and Imposition Files
The purpose of this section is to determine if any of the imposition files or queues used in chapter 4 have already been created.
The following procedures explain how to check for pre-existing imposition files and queues.
Check for Existing Imposition Files
A new imposition file is required only if the paper stock is being changed. An imposition file may have already been created to accommodate the new paper stock width. The following procedure explains how to check for existing imposition files.
1.
Ensure that the Xerox 490/980 Color Continuous Feed Printing System is powered on and is connected to the PC-UI.
2.
Select [Resource Management] on the left-side navigation pane of the PC-UI.
3.
Look for any imposition files that are named with the following convention:
• Simplex_PreCal_[Paper Stock Width]
Note
As an example, if you were changing to 18 in (457 mm) width paper stock, you would look for an imposition file called [Simplex_PreCal_18in].
4.
If you find an imposition file that has the width of paper stock you are using, you can skip
the Set Up Imposition Files section of Chapter 4.
5.
If you do not find an imposition file that has the width of paper stock that you are using,
you must perform the Set Up Imposition Files section of Chapter 4.
Check for Existing Queues
A new queue is required only if the paper stock width is being changed. A queue may have already been created to accommodate the new paper stock width. The following procedure explains how to check for existing queues.
1.
Ensure that the Xerox 490/980 Color Continuous Feed Printing System is powered on and is connected to the PC-UI.
2.
Select [Queue Management] on the left-side navigation pane of the PC-UI.
3.
Look for any imposition files that are named with the following convention:
• TRC_[Paper Stock Width]
Note
As an example, if you were changing to 19.5 in (495 mm) width paper stock, you would look for a queue called [TRC_19-5in].
4.
If you find a queue that has the width of paper stock you are using, you can skip the
Create a New Queue section of Chapter 4.
5.
If you do not find a queue that has the width of paper stock that you are using, you must perform the
section of Chapter 4.
Color Management Guide 3-11
Prepare for Color Calibration Xerox 490/980 Color Continuous Feed Printing System
3-12 Color Management Guide
Pre-Calibration
Engine Density
Adjustment
This chapter discusses how to set the color densities of Yellow, Magenta, Cyan and Black (Y/M/
C/K) to within optimal parameters for color calibration.
This procedure should be performed as desired, but especially:
• After changing the Developer of a color
• After using approximately one roll of paper since the Developer of a color was changed
• When the highest level of image quality is required
4
Color Management Guide 4-1
advertisement
Related manuals
advertisement
Table of contents
- 1 Cover Page
- 3 Table of Contents
- 5 Color Management Overview
- 6 CMS Option Tool Overview
- 6 Major Functions of the CMS Option Tool
- 7 CMS Option Tool Setup
- 7 Prerequisites to setting up CMS Option Tool
- 7 Color Options
- 7 Color Resource Set
- 7 Convert CMYK/RGB Black to K
- 8 Black Overprint
- 8 Color Characteristics
- 11 Pre-Printed Paper
- 13 CMS Option Tool
- 13 Introduction to the CMS Option Tool
- 13 Measuring devices
- 14 Install the CMS Option Tool
- 15 CMS Option tool tab menus
- 15 After the installation
- 16 Cancelling the installation
- 16 Uninstall the CMS Option Tool
- 17 Using the CMS Option Tool
- 20 Create Calibration Data
- 22 Custom Paper
- 24 Registering Custom Paper
- 25 Custom Ink Characteristic
- 25 Paper Information
- 28 Color Resource Management
- 29 Prepare for Color Calibration
- 30 Recommended Calibration Conditions
- 31 Verify Color Calibration Resources
- 36 Copy Color Calibration Resources
- 38 Download ColorPort Utility Software
- 39 Check for Queue and Imposition Files
- 39 Check for Existing Imposition Files
- 39 Check for Existing Queues
- 41 Pre-Calibration Engine Density Adjustment
- 42 Create an Empty Color Resource
- 42 For Simplex Systems
- 44 For Duplex Systems
- 46 Set Up Imposition Files
- 46 Import Simplex/Duplex Imposition Files
- 47 Manipulate the Imported Simplex Imposition File
- 48 Manipulate the Imported Duplex Imposition File
- 49 Create a New Queue
- 49 Create a new Simplex Queue
- 53 Create a new Duplex Queue
- 58 Color Density Adjustment
- 61 Color Calibration Process for v1.1.6 Software
- 62 Create a TRC File
- 62 For Simplex Systems
- 66 For Duplex Systems
- 71 Regional Settings
- 72 Use ColorPort to Measure Targets
- 74 Create TRC File with TRC Viewer
- 74 For Simplex Systems
- 76 For Duplex Systems
- 78 Import TRC File into PC-UI
- 78 For Simplex Systems
- 80 For Duplex Systems
- 81 Create a New Queue for Calibration Confirmation
- 82 For Simplex Systems
- 85 For Duplex Systems
- 88 Post-Calibration Density Check
- 90 Apply a Calibration TRC to existing Queues using the User TRC option
- 90 For Simplex Systems
- 90 For Duplex Systems
- 91 Color Calibration Using ColorPort Utility Software
- 92 Color Calibration
- 93 Using ColorPort for Color Calibration
- 95 Appendix A - Logical Page Setting
- 95 Logical Page Setting
- 95 Offset Specification
- 95 Logical Page Size
- 96 Offset Specification and Logical Page Size Explained
- 97 Calculate Offset Specification and Logical Page Size Values
- 98 Table of Offset Specification and Logical Page Size Values
- 99 Appendix B - Print Using LPR
- 99 Print Using LPR
- 102 Copyright Page