Create a New Queue for Calibration Confirmation. Xerox 490
Add to My manualsadvertisement
Xerox 490/980 Color Continuous Feed Printing System Color Calibration Process for v1.1.6 Software
Create a New Queue for Calibration
Confirmation
Depending on whether a simplex or duplex system exists, use the appropriate procedure on the following pages.
Color Management Guide 5-21
Color Calibration Process for v1.1.6 Software Xerox 490/980 Color Continuous Feed Printing System
For Simplex Systems
Create a queue that uses the TRC created for the upstream User TRC.
1.
On the left-side navigation pane of the Xerox 490/980 Color Continuous Feed Printing
System PC-UI, select [Queue Management].
2.
Select [New].
3.
In the Queue Name field, type [CalibrationConfirmation].
4.
Under the Data Format drop-down menu, select [PDF].
5.
In the Delete Job After Printing box, select the [Manual] radio button.
6.
For Input Process Mode, select the [Spool] and [Do Not Hold Job] radio buttons.
7.
For Output Process Mode, select the [Spool] and [Do Not Hold Job] radio buttons.
8.
In the Extended Spool box, select the [Enable] radio button.
9.
Select the [Paper Setting] tab.
10. Ensure that the Stock Set Name is [SYSTEM_DEFAULT].
11. In the Paper Identifier drop-down menu, select the imposition file [Simplex_PreCal].
5-22 Color Management Guide
Xerox 490/980 Color Continuous Feed Printing System Color Calibration Process for v1.1.6 Software
12. Select the [Color] tab.
13. In the Color Characteristics [Upstream] box, in the Printer Name drop-down menu, select
[PRINTER1].
14. In the Color Characteristics [Upstream] box, select [Setting].
15. In the User TRC drop-down menu, select [Upstream.trc].
16. In the Resource Group Name drop-down menu, select [TRC_PRINTER1.cntl].
17. Select [OK].
18. Select the [PDF] tab.
19. In the Page Size drop-down menu, select [Non-standard].
Color Management Guide 5-23
Color Calibration Process for v1.1.6 Software Xerox 490/980 Color Continuous Feed Printing System
Note
In the following step, while using Inches is recommended, it is not required. Millimeters are also supported by this documentation.
20. For Unit, select [Inch].
21. In the Width field type [8.50] (216 mm). In the Length field type [12.00] (305 mm).
22. In the Copies drop-down menu, type [10].
23. Select [OK].
5-24 Color Management Guide
Xerox 490/980 Color Continuous Feed Printing System Color Calibration Process for v1.1.6 Software
For Duplex Systems
Create a queue that uses the TRC’s created for the upstream and downstream as User TRC’s.
1.
On the left-side navigation pane of the Xerox 490/980 Color Continuous Feed Printing
System PC-UI, select [Queue Management].
2.
Select [New].
3.
In the Queue Name field, type [CalibrationConfirmation].
4.
Under the Data Format drop-down menu, select [PDF].
5.
In the Delete Job After Printing box, select the [Manual] radio button.
6.
For Input Process Mode, select the [Spool] and [Do Not Hold Job] radio buttons.
7.
For Output Process Mode, select the [Spool] and [Do Not Hold Job] radio buttons.
8.
In the Extended Spool box, select the [Enable] radio button.
9.
Select the [Paper Setting] tab.
10. In the Paper Identifier drop-down menu, select the imposition file [Duplex_PreCal].
Color Management Guide 5-25
Color Calibration Process for v1.1.6 Software Xerox 490/980 Color Continuous Feed Printing System
11. Select the [Color] tab.
12. In the Color Characteristics [Upstream] box, in the Printer Name drop-down menu, select
[PRINTER1].
13. In the Color Characteristics [Upstream] box, select [Setting].
14. In the User TRC drop-down menu, select [Upstream.trc].
15. In the Resource Group Name drop-down menu, select [TRC_PRINTER1.cntl].
16. Select [OK].
17. In the Color Characteristics [Downstream] box, in the Printer Name drop-down menu, select
[PRINTER2].
18. In the Color Characteristics [Downstream] box, select [Setting].
19. In the User TRC drop-down menu, select [Downstream.trc].
20. In the Resource Group Name drop-down menu, select [TRC_PRINTER2.cntl].
21. Select [OK].
5-26 Color Management Guide
Xerox 490/980 Color Continuous Feed Printing System Color Calibration Process for v1.1.6 Software
22. Select the [PDF] tab.
23. In the Page Size drop-down menu, select [Non-standard].
Note
In the following step, while using Inches is recommended, it is not required. Millimeters are also supported by this documentation.
24. For Unit, select [Inch].
25. In the Width field type [5.6] (142 mm). In the Length field type [12.00] (305 mm).
26. In the Copies drop-down menu, type [10].
27. Select [OK].
Color Management Guide 5-27
advertisement
Related manuals
advertisement