1 Getting Started. Pentax Optio W80
Annonce
Annonce
1
Getting Started
Attaching the Strap ................................... 32
Powering the Camera ............................... 33
Installing the SD Memory Card ................ 39
Turning the Camera On and Off .............. 43
Initial Settings ........................................... 45
Attaching the Strap
1
Attach the strap (O-ST20) supplied with the camera.
1
Pass the narrow end of the strap through the strap lug.
2
Pass the other end of the strap through the loop and pull tight.
32
Powering the Camera
Charging the Battery
Use the supplied battery charger (D-BC78) to charge the supplied rechargeable lithium-ion battery (D-LI78) before using it in the camera for the first time or after a long period of non-use, or when the [Battery depleted] message appears.
Note: AC plug cord “Listed, Type SPT-2 or NISPT-2, 18/2 flexible cord, rated 125 V, 7A, minimum 6 ft (1.8 m)”
Charging indicator
While charging: Lights
Charging finished: Turns off
2
To power outlet
3
1
Battery
1
AC plug cord
Battery charger
1
Connect the AC plug cord to the battery charger.
2
Plug the AC plug cord into the power outlet.
3
Place the battery in the battery charger so that the
PENTAX logo is facing up.
The charging indicator turns on while charging.
When charging is finished, the charging indicator turns off.
4
Remove the battery from the battery charger when charging is finished.
• Do not charge batteries other than the rechargeable lithium ion D-LI78 battery using the supplied D-BC78 battery charger. Doing otherwise may cause damage or overheating.
• The battery has reached the end of its service life when it starts to run down soon after being charged. Replace it with a new battery.
• If the battery is inserted correctly but the charging indicator fails to light, the battery may be faulty. Replace it with a new battery.
33
The time required to fully charge the battery is about 150 minutes (max.).
(The charging time may vary depending on the ambient temperature and charging conditions.) The appropriate ambient temperature for charging the battery is 0°C to 40°C (32°F to 104°F).
1
Installing the Battery
Use the rechargeable lithium-ion battery D-LI78 that is provided with the camera. Charge the battery before using it in the camera for the first time.
Battery lock lever
Battery/card/terminal cover lock lever
34
Battery/card/ terminal cover
Battery
1
Open the battery/card/terminal cover.
Press the battery/card/terminal cover lock lever in the direction shown
1 , slide the cover towards 2 and open it towards 3.
2
Using the side of the battery to press the battery lock
lever in the direction of 4, insert the battery with the
PENTAX logo pointing toward the lens.
Push the battery in until it is locked in place.
Make sure that the battery is inserted with the PENTAX logo pointing toward the lens. If the battery is incorrectly oriented, malfunction may result.
3
Close the battery/card/terminal cover.
Slide the battery/card/terminal cover lock lever in the opposite direction indicated by 2. If you hear a click, the cover is securely closed.
Removing the Battery
1
Open the battery/card/terminal cover.
2
Press the battery lock lever towards 4.
The battery will be ejected. Take care not to drop the battery when removing it.
• Do not use excessive force when sliding the battery/card/terminal cover open and closed because the waterproof packing may peel off.
If the packing is not in the correct position, the camera will not be waterproof.
• If the battery/card/terminal cover is not locked securely when you close it, water, sand, or dirt may get into the camera.
• This camera uses a rechargeable lithium-ion battery D-LI78. Use of any other type of battery may damage the camera and cause malfunction.
• Insert the battery correctly. If the battery is incorrectly oriented, malfunction may result.
• Do not remove the battery while the camera is turned on.
• When storing the battery for more than 6 months, charge the battery for 30 minutes using the battery charger and store the battery separately.
Be sure to recharge the battery every 6 to 12 months. Storing the battery below room temperature is ideal. Avoid storing it in high temperatures.
• The date and time may be returned to the default setting if the camera is left without the battery for a long time.
• Be careful as the camera or the battery may become hot when the camera is used continuously for a long period of time.
• Allow the camera to dry completely before changing the battery. Avoid changing the battery where the camera is likely to get wet or dirty, and make sure that your hands are dry.
• Battery performance may deteriorate as temperature decreases.
When using the camera in cold regions, we recommend carrying a spare battery in your pocket to keep it warm. Battery performance will return to normal in normal temperatures.
1
35
• Image Storage Capacity, Movie Recording Time, Sound
Recording Time, and Playback Time
(at 23°C or 73.4°F with the display on and the battery fully charged)
1 Image Storage
Capacity
*1
(flash used for 50% of shots)
Approx. 170 pictures
Movie Recording
Time
*2
Sound Recording
Time
*2
Playback Time *2
Approx. 65 min.
Approx. 230 min.
Approx. 180 min.
*1 Recording capacity shows approximate number of shots recorded during CIPA-compliant testing (with display on, flash used for 50% of the shots, and 23°C or 73.4°F). Actual performance may vary according to operating conditions.
*2 According to the results of in-house testing.
• In general, battery performance may temporarily deteriorate as the temperature decreases.
• Be sure to take a spare battery with you when traveling abroad or to a cold region, or if you intend to take a lot of pictures.
• Battery Level Indicator
You can check the battery level by the indicator on the display.
Screen Display
(green)
(green)
(yellow)
(red)
[Battery depleted]
Battery Status
Adequate power remains.
Battery is running low.
Battery is running very low.
Battery is exhausted.
The camera will turn off after this message appears.
36
Using the AC Adapter
Use of the optional AC adapter kit (K-AC78) is recommended if you intend to use the camera for a long time or connect it to a computer.
1
1
6
5
3 DC coupler
4
DC terminal
1
Make sure that the camera is turned off and open the battery/card/terminal cover.
2
Remove the Battery.
Refer to p.34 - p.35 on how to open the battery/card/terminal cover and
remove the battery.
3
Insert the DC coupler.
Using the side of the DC coupler to press the battery lock lever, insert the DC coupler. Confirm that the DC coupler is locked in place.
The battery/card/terminal cover will not close while the DC coupler is inserted. Leave the cover open when using the AC adapter and do not attempt to close it.
4
Connect the DC terminal of the AC adapter to the DC terminal of the DC coupler.
5
Connect the AC plug cord to the AC adapter.
6
Plug the AC plug cord into the power outlet.
37
1
• Make sure that the camera is turned off before connecting or disconnecting the AC adapter.
• Make sure that the AC plug cord and the DC terminal connecting the
AC adapter to the camera are inserted securely. Data may be lost if either becomes disconnected while data is being recorded on the SD
Memory Card or the built-in memory.
• Use the AC adapter with due care to avoid fire or electric shock.
Be sure to read “About the Battery Charger and the AC Adapter” (p.3)
before using the AC adapter.
• Be sure to read the operation manual accompanying the AC adapter kit K-AC78 before using the adapter.
• When connecting the AC adapter, you cannot set the camera upright on the table because the cord from the DC coupler comes out of the bottom of the camera.
• Do not use excessive force when sliding the battery/card/terminal cover open and closed because the waterproof packing may peel off.
If the packing is not in the correct position, the camera will not be waterproof.
38
Installing the SD Memory Card
This camera uses either an SD Memory Card or an SDHC Memory Card.
(Both cards are referred to as SD Memory Cards hereafter.) Captured images and sound files are saved on the SD Memory Card if a card is inserted in the camera. They are saved in the built-in memory if a card is
1
• Be sure to use this camera to format (initialize) an SD Memory
Card that is unused or has been used on other cameras or digital
devices. Refer to “Formatting an SD Memory Card” (p.200) for
instructions on formatting.
• Make sure that the camera is turned off before inserting or removing the SD Memory Card.
• Allow the camera to dry completely before changing the SD Memory
Card. Avoid changing the card where the camera is likely to get wet or dirty, and make sure that your hands are dry.
• Do not use excessive force when sliding the battery/card/terminal cover open and closed because the waterproof packing may peel off.
If the packing is not in the correct position, the camera will not be waterproof.
• The still picture storage capacity varies depending on the capacity of the SD Memory Card and the selected number of recorded pixels and
• The power lamp blinks while the SD Memory Card is being accessed
(data is being recorded or read).
Backing Up Data
The camera may not be able to access data in the built-in memory in the case of a malfunction. Use a computer or other device to back up important data in another location.
39
1
40
SD Memory Card socket
SD Memory Card
Battery/card/ terminal cover
1
Open the battery/card/terminal cover.
Press the battery/card/terminal cover lock lever in the direction shown
1 , slide the cover towards 2 and open it towards 3.
2
Insert the SD Memory Card into the SD Memory Card socket so that the label is facing toward the front of the camera (the side with the lens).
Push the card in all the way. Images and sound may not be recorded correctly if the card is not inserted all the way.
3
Close the battery/card/terminal cover.
Slide the battery/card/terminal cover lock lever in the opposite direction indicated by 2. If you hear a click, the cover is securely closed.
To Remove the SD Memory Card
1
Open the battery/card/terminal cover.
2
Push the card into the SD Memory Card socket to eject it.
Pull the card out.
If the battery/card/terminal cover is not locked securely when you close it, water, sand, or dirt may get into the camera.
Precautions When Using an SD Memory Card
• The SD Memory Card is equipped with a write-protect switch. Setting the switch to
LOCK prevents new data from being recorded on the card, the stored data from being deleted, and the card from being formatted by the camera or a computer.
r appears on the display when the card is write-protected.
Write-protect switch
• Care should be taken when removing the SD Memory Card immediately after using the camera, as the card may be hot.
• Do not remove the SD Memory Card or turn off the camera while data is being written or played back from the SD Memory Card or while connected to a computer with a USB cable. Doing so may result in data corruption or damage to the card.
• Do not bend the SD Memory Card or subject it to violent impact. Keep it away from water and store away from high temperature.
• Never remove the SD Memory Card while it is being formatted. This may damage the card and make it unusable.
• The data on the SD Memory Card may be deleted in the following circumstances. We do not accept any liability for data that is deleted. This includes the following:
(1) When the SD Memory Card is mishandled by the user.
(2) When the SD Memory Card is exposed to static electricity or electrical interference.
(3) When the SD Memory Card has not been used for a long time.
(4) When the SD Memory Card is ejected or the battery is removed while the data on the card is being recorded or accessed.
• If it is not used for a long time, the data on the card may become unreadable.
Be sure to regularly make a backup of important data on a computer.
• Avoid using or storing the card where it may be exposed to static electricity or electrical interference.
• Avoid using or storing the card in direct sunlight or where it may be exposed to rapid changes in temperature or to condensation.
• When using an SD Memory Card with a slow recording speed, recording may stop while you are taking movies even when there is adequate space in the memory, or shooting and playback may take a long time.
• Be sure to format SD Memory Cards that are unused or have been used on
another camera. Refer to “Formatting an SD Memory Card” (p.200).
• Please note that formatting the SD Memory Card will not necessarily delete the data so that it cannot be recovered using off-the-shelf data recovery software. There are off-the-shelf secure data deletion software programs available that will completely delete the data. If you are going to discard, give away or sell your SD Memory Card, you should ensure that the data on the card is completely deleted or the card itself is destroyed if it contains any personal or sensitive information. In any case, the data on your SD Memory
Card should be managed at your own risk.
1
41
1
Number of Images Recordable on an SD Memory
Card
The size of a recorded image differs depending on the number of recorded pixels of the images. This affects the number of images that can be saved on an SD Memory Card.
Choose the appropriate number of recorded pixels for still pictures on the
[A Rec. Mode] menu.
Selecting the Number of Recorded Pixels 1p.113
Choose the appropriate number of recorded pixels and frame rate in
[Movie] on the [A Rec. Mode] menu.
Selecting the Number of Recorded Pixels and Frame Rate for Movies
1
For an approximate guide to the number of images or the length of
recorded movies that can be saved on an SD Memory Card, see “Main
42
Turning the Camera On and Off
Power switch/Power lamp
1
1
Press the power switch.
The camera turns on and both the power lamp and display turn on.
If the [Language/ ] screen or [Date Adjustment] screen appears
when you turn the camera on, follow the procedure on p.45 to set the
display language and/or current date and time.
2
Press the power switch again.
The camera turns off and both the power lamp and display turn off.
Checking the SD Memory Card
The SD Memory Card is checked when the camera turns on and the memory status is displayed.
a
+ r
The SD Memory Card is inserted. Images and sound files will be saved on the SD Memory
Card.
The SD Memory Card is not inserted. Images and sound files will be saved in the built-in memory.
The write-protect switch on the SD Memory Card
is in the LOCK position (p.41). Images and
sounds cannot be recorded.
Memory status
43
1
Starting-up in the Playback Mode
Use this function when you want to play back images or sound files straightaway without taking any pictures.
Power switch
Q button
1
Press the power switch while holding down the Q button.
The display turns on and the camera starts up in playback mode.
To switch from Playback Mode to A mode, press the Q button or press the shutter release button halfway.
Playing Back Still Pictures 1p.146
44
Initial Settings
The [Language/ ] screen appears when the camera is turned on for
the first time. Perform the operations in “Setting the Display Language”
below to set the language, and in “Setting the Date and Time” (p.49) to
set the current date and time.
The language, date, and time can be changed later. Refer to the pages below for instructions.
• To change the language, follow the steps in “Changing the Display Language”
• To change the date and time, follow the steps in “Changing the Date and
1
Setting the Display Language
3 button
Four-way controller
4 button
1
Use the four-way controller
(2345) to choose the display language.
E n g l i s h
Deutsch
D a n s k
Svenska
S u o m i
P o l s k i
I t a l i a n o
Nederlands
MENU C a n c e l
Magyar
OK O K
45
1
2
Press the 4 button.
The [Initial Setting] screen appears in the selected language. If the desired settings for [Hometown] and [DST] (Daylight Saving
Time) appear, use the four-way controller
Initial Setting
Hometown
New York
English
DST
(23) to move the frame to [Settings complete], and press the 4 button to MENU
Settings complete
Cancel display the [Date Adjustment] screen. Go to
DST
“Setting the Date and Time” (p.49).
Go to step 3 in “To Set Hometown and DST” (p.48) if the desired
settings do not appear.
46
If you accidentally select the wrong language and go to the next procedure, perform the following operation to set the language back.
When the Wrong Language Has Been Inadvertently Selected
1
Press the four-way controller (5).
2
Use the four-way controller (2345) to select the
language and press the 4 button.
The [Initial Setting] screen appears in the selected language.
When the Screen After Step 2 Appears in the Wrong Language
1
Press the 3 button.
This exits the settings screen and returns the camera to capture mode.
2
Press the 3 button.
The [A Rec. Mode] menu appears.
3
Press the four-way controller (5).
4
Use the four-way controller (32) to select [Language/
].
5
Press the four-way controller (5).
The [Language/ ] screen appears.
6
Use the four-way controller (2345) to select the language.
7
Press the 4 button.
The [W Setting] menu appears in the selected language.
The language is now switched to your desired language. To reset [Hometown],
[Date] and [Time], refer to the pages below for instructions.
• To change [Hometown], follow the steps in “Setting the World Time”
• To change the date and time, follow the steps in “Changing the Date and
1
47
1
To Set Hometown and DST
3
Press the four-way controller (3).
The frame moves to [Hometown].
4
Press the four-way controller (5).
The [Hometown] screen appears.
Initial Setting
English
Hometown
New York
Settings complete
MENU Cancel
DST
5
Use the four-way controller (45) to choose a city.
H o m e t o w n
C i t y
D S T
N e w Yo r k
MENU C a n c e l OK O K
6
Press the four-way controller (3).
The frame moves to [DST] (Daylight Saving Time).
7
Use the four-way controller (45) to select O (On) or P (Off).
8
Press the 4 button.
The [Initial Setting] screen appears.
9
Press the four-way controller (23) to move the frame
to [Settings complete] and press the 4 button.
The [Date Adjustment] screen appears. Next, set the date and time.
The video output format (NTSC/PAL) is set to the format of the city selected in
[Hometown] on the [Initial Setting] screen. See the following pages for information on the available video output formats and how to change the initial settings.
• Video output formats available initially: “List of World Time Cities” (1p.260)
• To change the video out format, follow the steps in “Changing the Video
48
Setting the Date and Time
Set the current date and time and the display format.
1
Press the four-way controller (5).
The frame moves to [mm/dd/yy].
2
Use the four-way controller (23) to choose the date and time display format.
Choose from [mm/dd/yy], [dd/mm/yy] or [yy/ mm/dd].
Date Adjustment
Date Format
Date mm dd yy 24h
0 1 / 0 1 / 2 0 0 9
Time 0 0 : 0 0
Settings complete
MENU Cancel
3
Press the four-way controller (5).
The frame moves to [24h].
4
Use the four-way controller (23) to select [24h] (24-hour display) or
[12h] (12-hour display).
Date Adjustment
Date Format
Date
Time mm dd yy 24h
0 1 / 0 1 / 2 0 0 9
0 0 : 0 0
Settings complete
MENU Cancel
5
Press the four-way controller (5).
The frame returns to [Date Format].
6
Press the four-way controller (3).
The frame moves to [Date].
Date Adjustment
Date Format
Date
Time mm dd yy 24h
0 1 / 0 1 / 2 0 0 9
0 0 : 0 0
Settings complete
MENU Cancel
7
Press the four-way controller (5).
The frame moves to the month.
1
49
1
8
Use the four-way controller (23) to change the month.
Change the day and year in the same manner.
Next, change the time.
If you selected [12h] in step 4, the setting switches between am and pm corresponding to the time.
9
Press the four-way controller (3).
The frame moves to [Settings complete].
10
Press the 4 button.
This confirms the date and time.
Date Adjustment
Date Format mm dd yy 24h
Date 0 1 / 0 1 / 2 0 0 9
Time 0 0 : 0 0
Settings complete
MENU Cancel
If you press the 4 button in step 10, the camera clock is reset to 00 seconds. To set the exact time, press the 4 button when the time signal (on the TV, radio, etc.) reaches 00 seconds.
When the [Initial Setting] or [Date Adjustment] screen is displayed, you can cancel the setting operation and switch to the capture mode by pressing the 3 button. In this case, the [Initial Setting] screen will appear next time you turn the camera on.
[Language/ ], [Date], [Time], [Hometown] and [DST] can be changed. Refer to the pages below for instructions.
• To change the language, follow the steps in “Changing the Display Language”
• To change the date and time, follow the steps in “Changing the Date and
• To change the city or turn DST on and off, follow the steps in “Setting the
50
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce