Inserting the Battery
49
Insert the battery into the camera. Use only a D-LI90 battery.
Charging the Battery
When using the battery for the first time, or when the battery has not been used in a long time, or when [Battery depleted] appears, recharge the battery.
Note: AC plug cord “Listed, Type SPT-2 or NISPT-2, 18/2 flexible cord, rated 125 V, 7A, minimum 6ft (1.8m)”
Indicator lamp
Lithium-ion battery
3
2
2
1 AC plug cord
Battery charger
1
Connect the AC plug cord to the battery charger.
2
Plug the AC plug cord into the power outlet.
3
Face the 2 mark on the exclusive battery up and insert it into the battery charger.
The indicator lamp is lit during charging and turns off when the battery is fully charged.
4
When the battery is fully charged, remove the battery from the battery charger.
50
2
• Do not use the provided battery charger D-BC90 to charge batteries other than rechargeable lithium-ion battery D-LI90. Charging other batteries may cause damage or heating.
• If the battery is correctly oriented and inserted into the battery charger but the indicator lamp is not lit, the battery is faulty. Use a new battery in the camera.
• The maximum charging time is approximately 390 minutes (it depends on temperature and remaining battery power.) Charge in a location where the temperature is between 0°C and 40°C.
• If battery usage time is reduced even when properly charged, the battery has reached the end of its life. Use a new battery in the camera.
Inserting/Removing the Battery
When using the battery for the first time, charge the battery and insert it into the camera.
• Do not open the battery cover or remove the battery while the power is on.
• Remove the battery when you will not use the camera for a long while. The battery may leak.
• If the date and time settings have been reset when you install a new battery after a long time has passed since the battery was removed, follow the
procedure for “Setting the Date and Time” (p.67).
• Insert the battery correctly. Batteries inserted incorrectly may cause a camera breakdown. Wipe the electrodes of the battery with a soft dry cloth before inserting.
• Be careful as the camera or battery may become hot when the camera is used continuously for a long period of time.
1
Open the battery cover.
Lift the battery cover unlock knob, turn it towards OPEN (1) to unlock, and then pull the cover open (2).
1
2
2
Face the 2 mark on the battery towards outside of the camera, push the battery lock lever in the direction of the
arrow (3) and insert the battery.
Insert until the battery locks.
To remove the battery, push the battery lock lever in the direction of the arrow (3) with your finger.
Remove the battery when it pops out slightly.
3
51
2
Battery lock lever
3
Close the battery cover (4) and turn the battery cover unlock
knob towards CLOSE (5) to lock.
Stow the battery cover unlock knob after closing the battery cover.
5
4
Use the AC adapter kit K-AC50 (optional) when using the camera for a
prolonged period. (p.53)
52
Battery Level Indicator
2
You can confirm remaining battery level by checking the w /A displayed on the status screen and LCD panel.
Status
Screen w (Green) x (Green) y (Yellow) z (Red)
[Battery depleted]
LCD Panel
A
B
C
D lit
D blinks
Battery Level
Battery is full.
Battery is close to full.
Battery is running low.
Battery is almost empty.
The camera turns off after displaying the message.
(D continues blinking on the LCD panel.)
•
• y, z (red), C or D may appear even when the battery level is sufficient if the camera is used at low temperatures or when performing continuous shooting for a long period of time. In this situation, turn the camera off and on again. If w or A appears, you can use the camera.
W is displayed when using the AC adapter.
Approximate Image Storage Capacity and
Playback Time (Battery Fully Charged)
Battery
D-LI90
(Temperature)
(23°C)
( 0°C)
Normal
Recording
980
810
Flash Photography
50% Use 100% Use
740
680
610
560
Playback Time
440 minutes
400 minutes
The image storage capacity (normal recording, flash use 50%) is based on measuring conditions in accordance with CIPA standards, while other data is based on our measuring conditions. Some deviation from the above figures may occur in actual use depending on shooting mode and shooting conditions.
• Battery performance temporarily decreases as the temperature decreases.
When using the camera in cold climates, have extra batteries on hand and keep them warm in your pocket. Battery performance will return to normal when returned to room temperature.
• Have extra batteries ready when traveling overseas, taking pictures in cold climates, or taking a lot of pictures.
53
Using the AC Adapter (Optional)
We recommend the use of the AC adapter kit K-AC50 (optional) when using the monitor for a long time or when connecting the camera to a computer or AV device.
1
Make sure the camera is turned off.
2
Open the terminal cover.
2
3
Face the 2 mark on the DC terminal of the AC adapter
towards the 2 mark on the camera, and connect the DC terminal to the DC input terminal of the camera.
54
4
Connect the AC plug cord to the AC adapter.
5
Plug the AC cord into the power outlet.
2
• Make sure the camera is turned off before connecting or disconnecting the
AC adapter.
• Make sure connections are secure between the terminals. SD Memory Card or data may be corrupted if disconnected while the card is being accessed.
• Be sure to read the manual of the AC adapter kit K-AC50 when using the AC adapter.
• The battery in your camera will not charge when connected to the AC adapter.
