Binding. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800
Add to My manuals32 Pages
advertisement
![Binding. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800 | Manualzz Binding. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800 | Manualzz](http://s1.manualzz.com/store/data/002503854_1-7513acdab7e9be265296efaff9b8aa77-360x466.png)
BINDING
You must bind the receiver to the transmitter before it will operate. Binding teaches the receiver the specific code of the transmitter.
Once bound, the receiver only connects to the transmitter when the previously bound model memory is selected. You will need to rebind the receiver after the model is set in the transmitter to fully program the model’s failsafe positions. If another model memory is selected, the receiver will not connect. This feature is called ModelMatch™ and prevents flying a model using the wrong model memory.
1. 3.
1. 2. 3.
EN
4.
4. HOLD BUTTON WHILE POWERING ON
HOLD BUTTON WHILE POWERING ON 5.
5.
6.
6.
Mode 2 Shown
1.
Mode 2 Shown
1. Lower throttle to the lowest position and make sure the transmitter is powered off.
2. Insert bind plug into the BIND/DATA port.
3. Insert receiver battery into ANY open port. The receiver’s LED will flash when the receiver is ready to bind.
4. While pressing the Trainer/Bind button, power on the transmitter.
Binding Using the Receiver and ESC
1. 2.
2. 3.
3.
5. Release the Trainer/Bind button after the receiver has stopped flashing rapidly, once the receiver’s LED stays illuminated; this indicates the receiver is bound to the transmitter. The screen also provides binding information.
6. Remove the bind plug from the receiver.
4.
4.
5.
5. HOLD BUTTON WHILE POWERING ON
HOLD BUTTON WHILE POWERING ON 6.
6.
7.
7.
Mode 2 Shown
1. Lower throttle to the lowest position and make sure the
2. Insert bind plug into the BIND/DATA port.
3. Insert ESC plug into the THRO port.
4. Connect battery to ESC and turn on ESC switch, if available.
The receiver’s LED will rapidly flash when the receiver is ready to bind.
5. While pressing the Trainer/Bind button, power on the transmitter.
SPEKTRUM DX7s • RADIO INSTRUCTION MANUAL
6. Release the Trainer/Bind button after the receiver has stopped flashing rapidly, once the receiver’s LED stays illuminated; this indicates the receiver is bound to the transmitter. The screen also provides binding information.
7. Remove the bind plug from the receiver.
7
advertisement
Related manuals
advertisement
Table of contents
- 4 Quick Start Guide
- 5 Charging Your Transmitter
- 5 Transmitter Batteries
- 6 Transmitter Functions
- 7 Binding
- 8 Using the transmitter
- 8 Antenna
- 8 Main Screen
- 9 Navigation
- 9 System Settings
- 9 User Name
- 9 Contrast
- 10 Selecting a Region (EU Version)
- 10 Selecting a Language
- 10 Acro and Heli setup
- 11 System Setup
- 11 Model Select
- 11 Model Type
- 11 Model Name
- 11 Switch Select
- 11 Model Reset
- 12 Model Copy
- 12 Warnings
- 12 Telemetry
- 13 Frame Rate
- 13 Wing Type
- 14 Differential
- 14 Flap System
- 14 Swash Type
- 15 Throttle, Pitch and Tail Curves
- 16 Governor
- 16 Flight Mode
- 16 Swashplate
- 17 Function List
- 17 Servo Setup
- 17 D/R & Exponential
- 17 Throttle Cut
- 18 Range Test
- 19 Timer
- 19 Monitor
- 19 Trainer
- 20 Failsafes
- 20 SmartSafe Failsafe
- 20 Hold Last Command
- 20 Preset Failsafe
- 21 Receiver and servo information
- 21 Receiver Installation
- 21 Servo Installation
- 21 Servo Precautions
- 21 Power System Requirements
- 21 Recommended Power System Guidelines
- 22 Appendix
- 22 Mode Conversion
- 23 Installing Optional LiPo Battery Pack
- 24 Servo Control
- 27 Troubleshooting Guide
- 27 Parts list
- 28 AMA National Model Aircraft Safety Code
- 29 FCC Information
- 29 FAA Information
- 31 Warranty and Service Contact Information
- 31 Parts Contact Information
- 31 Compliance Information for the European Union